[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.101.99 (3 ms) => setenv serverip 192.168.101.1 setenv serverip 192.168.101.1 => tftp 0x10000000 9098038/tftp-deploy-m99tx5w0/kernel/zImage tftp 0x10000000 9098038/tftp-deploy-m99tx5w0/kernel/zImage Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.99 Filename '9098038/tftp-deploy-m99tx5w0/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 2.5 MiB/s done Bytes transferred = 8729088 (853200 hex) => tftp 0x14000000 9098038/tftp-deploy-m99tx5w0/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9098038/tftp-deploy-m99tx5w0/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.99 Filename '9098038/tftp-deploy-m99tx5w0/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 3 MiB/s done Bytes transferred = 9400058 (8f6efa hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9098038/tftp-deploy-m99tx5w0/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9098038/tftp-deploy-m99tx5w0/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.99 Filename '9098038/tftp-deploy-m99tx5w0/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.3 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/9098038/extract-nfsrootfs-k6w54xfs,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/9098038/extract-nfsrootfs-k6w54xfs,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x853200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9399994 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.272-cip91 (KernelCI@build-j1017050-arm-gcc-10-multi-v7-defconfig-pql88) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Fri Feb 10 10:26:06 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/9098038/extract-nfsrootfs-k6w54xfs,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 942984K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 40056K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000025] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.003066] Console: colour dummy device 80x30 [ 0.003110] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.003125] pid_max: default: 32768 minimum: 301 [ 0.003262] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003285] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003818] CPU: Testing write buffer coherency: ok [ 0.003847] CPU0: Spectre v2: using BPIALL workaround [ 0.004210] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.004882] Setting up static identity map for 0x10300000 - 0x103000a0 [ 0.006464] rcu: Hierarchical SRCU implementation. [ 0.009588] EFI services will not be available. [ 0.009887] smp: Bringing up secondary CPUs ... [ 0.010673] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.010679] CPU1: Spectre v2: using BPIALL workaround [ 0.011580] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.011585] CPU2: Spectre v2: using BPIALL workaround [ 0.012452] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.012458] CPU3: Spectre v2: using BPIALL workaround [ 0.012558] smp: Brought up 1 node, 4 CPUs [ 0.012570] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.012579] CPU: All CPU(s) started in SVC mode. [ 0.013640] devtmpfs: initialized [ 0.020987] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.021335] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.021358] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.024528] pinctrl core: initialized pinctrl subsystem [ 0.026122] DMI not present or invalid. [ 0.026944] NET: Registered protocol family 16 [ 0.030412] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.032695] cpuidle: using governor menu [ 0.032874] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.042659] vdd1p1: supplied by regulator-dummy [ 0.043179] vdd3p0: supplied by regulator-dummy [ 0.043668] vdd2p5: supplied by regulator-dummy [ 0.044177] vddarm: supplied by regulator-dummy [ 0.044833] vddpu: supplied by regulator-dummy [ 0.045219] vddsoc: supplied by regulator-dummy [ 0.059274] No ATAGs? [ 0.059412] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.059426] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.062814] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory [ 0.063057] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.068196] Serial: AMBA PL011 UART driver [ 0.070553] console [pstore-1] enabled [ 0.070743] pstore: Registered ramoops as persistent store backend [ 0.070758] ramoops: attached 0x10000@0x30000000, ecc: 0/0 [ 0.093191] mxs-dma 110000.dma-apbh: initialized [ 0.100653] vgaarb: loaded [ 0.101475] SCSI subsystem initialized [ 0.101898] usbcore: registered new interface driver usbfs [ 0.101950] usbcore: registered new interface driver hub [ 0.102007] usbcore: registered new device driver usb [ 0.103252] i2c i2c-0: IMX I2C adapter registered [ 0.103274] i2c i2c-0: can't use DMA, using PIO instead. [ 0.103823] i2c i2c-1: IMX I2C adapter registered [ 0.103841] i2c i2c-1: can't use DMA, using PIO instead. [ 0.104249] i2c i2c-2: IMX I2C adapter registered [ 0.104266] i2c i2c-2: can't use DMA, using PIO instead. [ 0.105817] pps_core: LinuxPPS API ver. 1 registered [ 0.105829] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.105853] PTP clock support registered [ 0.106095] EDAC MC: Ver: 3.0.0 [ 0.108819] clocksource: Switched to clocksource mxc_timer1 [ 0.167828] NET: Registered protocol family 2 [ 0.168302] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.169590] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.169633] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.169724] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.169877] TCP: Hash tables configured (established 8192 bind 8192) [ 0.170095] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.170142] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.170310] NET: Registered protocol family 1 [ 0.170826] RPC: Registered named UNIX socket transport module. [ 0.170839] RPC: Registered udp transport module. [ 0.170848] RPC: Registered tcp transport module. [ 0.170857] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.171318] Trying to unpack rootfs image as initramfs... [ 0.889286] Freeing initrd memory: 9180K [ 0.889721] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.890101] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.892106] Initialise system trusted keyrings [ 0.892398] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 0.898389] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.899070] NFS: Registering the id_resolver key type [ 0.899139] Key type id_resolver registered [ 0.899149] Key type id_legacy registered [ 0.899192] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.901416] Key type asymmetric registered [ 0.901432] Asymmetric key parser 'x509' registered [ 0.901484] bounce: pool size: 64 pages [ 0.901531] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.901544] io scheduler noop registered [ 0.901555] io scheduler deadline registered [ 0.901699] io scheduler cfq registered (default) [ 0.901711] io scheduler mq-deadline registered [ 0.901722] io scheduler kyber registered [ 0.923485] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 0.923567] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 0.923739] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 0.923796] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 0.936830] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set [ 0.936904] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc [ 0.936964] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set [ 0.937057] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 [ 0.937204] PU : no governor for states [ 0.937228] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc [ 0.945292] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.945316] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.991569] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.995212] SuperH (H)SCI(F) driver initialized [ 0.996112] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX [ 0.996892] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX [ 1.903993] console [ttymxc1] enabled [ 1.908889] msm_serial: driver initialized [ 1.913249] STMicroelectronics ASC driver initialized [ 1.920187] STM32 USART driver initialized [ 1.935074] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 1.943522] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 1.950240] panel-simple panel-lcd: Dropping the link to regulator.0 [ 1.956734] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 1.965509] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 1.972419] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 1.986735] brd: module loaded [ 1.999388] loop: module loaded [ 2.005697] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 2.013680] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 2.021715] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 2.029920] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 2.040429] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 2.047425] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 2.056254] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 2.066780] scsi host0: ahci-imx [ 2.070622] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 [ 2.089341] CAN device driver interface [ 2.094440] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.101263] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator [ 2.109961] fec 2188000.ethernet: Linked as a consumer to regulator.0 [ 2.118782] pps pps0: new PPS source ptp0 [ 2.140252] fec 2188000.ethernet eth0: registered PHC device 0 [ 2.147386] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 2.153256] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.159253] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 2.166219] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.177678] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.185143] usbcore: registered new interface driver pegasus [ 2.190862] usbcore: registered new interface driver asix [ 2.196296] usbcore: registered new interface driver ax88179_178a [ 2.202440] usbcore: registered new interface driver cdc_ether [ 2.208327] usbcore: registered new interface driver smsc75xx [ 2.214140] usbcore: registered new interface driver smsc95xx [ 2.219940] usbcore: registered new interface driver net1080 [ 2.225633] usbcore: registered new interface driver cdc_subset [ 2.231601] usbcore: registered new interface driver zaurus [ 2.237248] usbcore: registered new interface driver cdc_ncm [ 2.245877] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.252442] ehci-pci: EHCI PCI platform driver [ 2.256929] ehci-platform: EHCI generic platform driver [ 2.262474] ehci-orion: EHCI orion driver [ 2.266711] SPEAr-ehci: EHCI SPEAr driver [ 2.270941] ehci-st: EHCI STMicroelectronics driver [ 2.276016] ehci-exynos: EHCI EXYNOS driver [ 2.280415] ehci-atmel: EHCI Atmel driver [ 2.284606] tegra-ehci: Tegra EHCI driver [ 2.288855] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.295070] ohci-pci: OHCI PCI platform driver [ 2.299581] ohci-platform: OHCI generic platform driver [ 2.305082] SPEAr-ohci: OHCI SPEAr driver [ 2.309311] ohci-st: OHCI STMicroelectronics driver [ 2.314377] ohci-atmel: OHCI Atmel driver [ 2.319415] usbcore: registered new interface driver usb-storage [ 2.327714] imx_usb 2184000.usb: Linked as a consumer to regulator.9 [ 2.339551] imx_usb 2184200.usb: Linked as a consumer to regulator.14 [ 2.349450] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 2.354365] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 2.388848] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 2.394896] hub 1-0:1.0: USB hub found [ 2.398692] hub 1-0:1.0: 1 port detected [ 2.408970] i2c /dev entries driver [ 2.426991] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [ 2.438168] sdhci: Secure Digital Host Controller Interface driver [ 2.444377] sdhci: Copyright(c) Pierre Ossman [ 2.451031] Synopsys Designware Multimedia Card Interface Driver [ 2.459072] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.465601] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [ 2.470806] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [ 2.476041] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 [ 2.515688] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 2.523467] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO [ 2.528714] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 [ 2.568331] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [ 2.578865] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.585109] ledtrig-cpu: registered to indicate activity on CPUs [ 2.591247] ata1.00: ATA-8: INTEL SSDSA2CW080G3, 4PC10362, max UDMA/133 [ 2.591959] usbcore: registered new interface driver usbhid [ 2.592239] mmc0: new high speed SDHC card at address 0001 [ 2.593888] mmcblk0: mmc0:0001 SD 14.6 GiB [ 2.597874] ata1.00: 156301488 sectors, multi 1: LBA48 NCQ (depth 32) [ 2.613269] ata1.00: configured for UDMA/133 [ 2.619701] usbhid: USB HID core driver [ 2.633990] NET: Registered protocol family 10 [ 2.639745] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2CW08 0362 PQ: 0 ANSI: 5 [ 2.639902] Segment Routing with IPv6 [ 2.648501] ata1.00: Enabling discard_zeroes_data [ 2.651677] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.656468] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB) [ 2.662784] NET: Registered protocol family 17 [ 2.669924] sd 0:0:0:0: [sda] Write Protect is off [ 2.674353] can: controller area network core (rev 20170425 abi 9) [ 2.685398] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.685412] NET: Registered protocol family 29 [ 2.694870] ata1.00: Enabling discard_zeroes_data [ 2.698931] can: raw protocol (rev 20170425) [ 2.707926] can: broadcast manager protocol (rev 20170425 t) [ 2.707988] sda: sda1 sda2 sda3 [ 2.713621] can: netlink gateway (rev 20170425) max_hops=1 [ 2.717865] ata1.00: Enabling discard_zeroes_data [ 2.722794] Key type dns_resolver registered [ 2.727358] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.736885] cpu cpu0: Linked as a consumer to regulator.4 [ 2.742389] cpu cpu0: Linked as a consumer to regulator.5 [ 2.747847] cpu cpu0: Linked as a consumer to regulator.6 [ 2.754093] ThumbEE CPU extension supported. [ 2.758379] Registering SWP/SWPB emulation handler [ 2.758849] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 2.770364] Loading compiled-in X.509 certificates [ 2.776804] pstore: Using compression: deflate [ 2.795322] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.802760] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.811323] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.818561] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.826981] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.835436] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.842165] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.849817] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 2.858560] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 2.865463] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 2.873813] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 2.873910] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 2.884039] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.890643] GPT:29296874 != 30560255 [ 2.890646] GPT:Alternate GPT header not at the end of the disk. [ 2.890649] GPT:29296874 != 30560255 [ 2.890651] GPT: Use GNU Parted to correct GPT errors. [ 2.890694] mmcblk0: p1 p2 p3 [ 2.897770] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.927203] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.934456] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.942816] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.951239] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.957914] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.965457] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 2.974226] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 2.981088] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 2.988507] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.995638] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 3.003146] hub 1-1:1.0: USB hub found [ 3.003681] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 3.014107] hub 1-1:1.0: 3 ports detected [ 3.014131] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 3.026547] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 3.034967] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 3.041676] panel-simple panel-lcd: Dropping the link to regulator.0 [ 3.049237] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 3.057985] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 3.064854] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 3.072287] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 3.079399] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 3.087245] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 3.094441] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 3.103117] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 3.109779] hctosys: unable to open rtc device (rtc0) [ 3.120246] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 3.128653] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 3.135426] panel-simple panel-lcd: Dropping the link to regulator.0 [ 3.143161] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 3.151952] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 3.158842] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 3.166325] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 3.173447] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 3.181351] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 3.188530] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 3.249487] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 3.264197] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 5.369521] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 5.398946] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 5.428970] Sending DHCP requests ., OK [ 6.252815] IP-Config: Got DHCP answer from 192.168.101.1, my address is 192.168.101.99 [ 6.260882] IP-Config: Complete: [ 6.264139] device=eth0, hwaddr=00:19:b8:07:40:03, ipaddr=192.168.101.99, mask=255.255.255.0, gw=192.168.101.1 [ 6.274634] host=imx6q-sabrelite-cbg-0, domain=lava.cbg.collabora.co.uk, nis-domain=(none) [ 6.283382] bootserver=192.168.101.1, rootserver=192.168.101.1, rootpath= [ 6.283390] nameserver0=192.168.101.1 [ 6.302452] Freeing unused kernel memory: 2048K [ 6.339165] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 7.151394] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.157173] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 7.159899] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.173321] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 7.174497] panel-simple panel-lcd: Dropping the link to regulator.0 [ 7.186647] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 7.187967] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 7.193293] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 7.202105] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 7.215098] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 7.221940] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 [ 7.229478] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) [ 7.229482] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 7.229531] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 7.252469] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 7.259698] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 7.268424] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.276886] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.283614] panel-simple panel-lcd: Dropping the link to regulator.0 [ 7.291611] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 7.300408] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 7.307280] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 7.315122] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 7.322273] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 7.330695] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 7.337903] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 7.346996] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.355530] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.362340] panel-simple panel-lcd: Dropping the link to regulator.0 [ 7.371910] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 7.380811] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 7.387841] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 7.394859] sgtl5000 0-000a: Linked as a consumer to regulator.7 [ 7.401128] sgtl5000 0-000a: Linked as a consumer to regulator.8 [ 7.407904] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 7.410824] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 7.415616] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 7.426392] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 7.428528] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 7.442385] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 7.451426] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.459911] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.466673] panel-simple panel-lcd: Dropping the link to regulator.0 [ 7.480009] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 7.488799] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 7.491318] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 7.496979] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 7.510151] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 7.517319] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 7.526433] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 7.533827] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 7.542520] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 7.543625] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.548642] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 7.557117] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.570914] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 [ 7.578449] panel-simple panel-lcd: Dropping the link to regulator.0 [ 7.586805] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 7.595664] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 7.602609] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 7.610570] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 7.617707] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 7.626205] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 7.633504] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 7.642519] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.650992] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.657692] panel-simple panel-lcd: Dropping the link to regulator.0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:07:40:03 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.101.1): address: 192.168.101.99 broadcast: 192.168.101.255 netmask: 255.255.255.0 gateway: 192.168.101.1 dns0 : 192.168.101.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-cbg-0 domain : lava.cbg.collabora.co.uk rootserver: 192.168.101.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 10.034010] systemd[1]: System time before build time, advancing clock. [ 10.092203] cgroup: cgroup2: unknown option "memory_recursiveprot" [ 10.107333] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 10.131882] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 10.181102] systemd[1]: Set hostname to . [ 10.956591] systemd[1]: Queued start job for default target Graphical Interface. [ 10.965458] random: systemd: uninitialized urandom read (16 bytes read) [ 10.972303] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 10.984741] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 10.994018] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 11.029093] random: systemd: uninitialized urandom read (16 bytes read) [ 11.036836] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 11.079202] random: systemd: uninitialized urandom read (16 bytes read) [ 11.086938] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 11.130049] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 11.169303] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 11.209663] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 11.249676] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 11.261906] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 11.299916] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 11.329419] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 11.369274] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 11.399493] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 11.430037] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 11.502610] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 11.512260] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 11.550566] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 11.591184] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 11.631473] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 11.670407] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 11.710345] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 11.719580] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 11.731833] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 11.772548] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 11.899252] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 11.946981] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 11.979423] random: systemd: uninitialized urandom read (16 bytes read) [ 11.989190] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 12.019406] random: systemd: uninitialized urandom read (16 bytes read) [ 12.029200] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 12.063144] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 12.073051] random: systemd: uninitialized urandom read (16 bytes read) [ 12.085536] systemd[1]: Starting Journal Service... Starting Journal Service... [ 12.126821] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 12.162561] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 12.201775] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 12.244070] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 12.258904] random: crng init done [ 12.262320] random: 22 urandom warning(s) missed due to ratelimiting [ 12.279795] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 12.320292] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 12.375722] systemd[1]: modprobe@configfs.service: Succeeded. [ 12.382287] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 12.419878] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... [ 12.700613] systemd-journald[164]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Reached target Hardware activated USB gadget. [ OK ] Started Network Time Synchronization. [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.272-cip91 #1 SMP Fri Feb 10 10:26:06 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9098038/extract-nfsrootfs-k6w54xfs' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9098038/extract-nfsrootfs-k6w54xfs' / # export NFS_SERVER_IP='192.168.101.1' export NFS_SERVER_IP='192.168.101.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9098038/environment . /lava-9098038/environment / # /lava-9098038/bin/lava-test-runner /lava-9098038/0 /lava-9098038/bin/lava-test-runner /lava-9098038/0 + export TESTRUN_ID=0_dmesg + cd /lava-9098038/0/tests/0_dmesg + cat uuid + UUID=9098038_1.6.2.4.1 + [ 29.073676] set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 29.188753] [ 29.265306] [ 29.357544] + set +x [ 29.366806] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-9098038/environment / # . /lava-9098038/environment/lava-9098038/bin/lava-test-runner /lava-9098038/1 / # /lava-9098038/bin/lava-test-runner /lava-9098038/1 + export TESTRUN_ID=1_bootrr + cd /lava-9098038/1/tests/1_bootrr + cat uuid + UUID=9098038_1.6.2.4.5 + set[ 29.955874] +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9098038/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds panel-lcd /lava-9098038/1/../bin/lava-test-case [ 31.119619] /lava-9098038/1/../bin/lava-test-case [ 31.206195] /lava-9098038/1/../bin/lava-test-case [ 31.248497] + set +x [ 31.287730] / #