[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.36 (14 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9726566/tftp-deploy-lzplgz7z/kernel/zImage tftp 0x10000000 9726566/tftp-deploy-lzplgz7z/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9726566/tftp-deploy-lzplgz7z/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################## 10.7 MiB/s done Bytes transferred = 10449408 (9f7200 hex) => tftp 0x14000000 9726566/tftp-deploy-lzplgz7z/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9726566/tftp-deploy-lzplgz7z/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9726566/tftp-deploy-lzplgz7z/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# # 5.5 MiB/s done Bytes transferred = 11460452 (aedf64 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9726566/tftp-deploy-lzplgz7z/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9726566/tftp-deploy-lzplgz7z/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9726566/tftp-deploy-lzplgz7z/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.6 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9726566/extract-nfsrootfs-jkgu1tar,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9726566/extract-nfsrootfs-jkgu1tar,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x9f7200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 11460388 Bytes = 10.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.277-cip94 (KernelCI@build-j1225729-arm-gcc-10-multi-v7-defconfig-kselftest-96h2r) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Mar 22 06:50:18 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s40104 r8192 d21336 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9726566/extract-nfsrootfs-jkgu1tar,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 928352K/1048576K available (15360K kernel code, 1762K rwdata, 6312K rodata, 2048K init, 7700K bss, 54688K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (16352 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1763 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7701 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 49054 entries in 192 pages [ 0.000000] Running RCU self tests [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU lockdep checking is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000035] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.003831] Console: colour dummy device 80x30 [ 0.003877] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.003901] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.003924] ... MAX_LOCK_DEPTH: 48 [ 0.003945] ... MAX_LOCKDEP_KEYS: 8191 [ 0.003968] ... CLASSHASH_SIZE: 4096 [ 0.003990] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.004011] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.004033] ... CHAINHASH_SIZE: 32768 [ 0.004055] memory used by lock dependency info: 4655 kB [ 0.004078] per task-struct memory footprint: 1536 bytes [ 0.004159] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.004193] pid_max: default: 32768 minimum: 301 [ 0.004528] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.004573] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006290] CPU: Testing write buffer coherency: ok [ 0.006383] CPU0: Spectre v2: using BPIALL workaround [ 0.007528] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.010005] Setting up static identity map for 0x10300000 - 0x103000a0 [ 0.012334] rcu: Hierarchical SRCU implementation. [ 0.016887] EFI services will not be available. [ 0.017873] smp: Bringing up secondary CPUs ... [ 0.020447] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.020460] CPU1: Spectre v2: using BPIALL workaround [ 0.023419] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.023431] CPU2: Spectre v2: using BPIALL workaround [ 0.026048] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.026061] CPU3: Spectre v2: using BPIALL workaround [ 0.026508] smp: Brought up 1 node, 4 CPUs [ 0.026539] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.026564] CPU: All CPU(s) started in SVC mode. [ 0.029472] devtmpfs: initialized [ 0.066240] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.068898] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.068957] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.072990] pinctrl core: initialized pinctrl subsystem [ 0.078108] DMI not present or invalid. [ 0.080174] NET: Registered protocol family 16 [ 0.089267] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.095848] cpuidle: using governor menu [ 0.096345] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.132125] vdd1p1: supplied by regulator-dummy [ 0.134170] vdd3p0: supplied by regulator-dummy [ 0.136004] vdd2p5: supplied by regulator-dummy [ 0.137826] vddarm: supplied by regulator-dummy [ 0.140402] vddpu: supplied by regulator-dummy [ 0.141753] vddsoc: supplied by regulator-dummy [ 0.191242] No ATAGs? [ 0.191729] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.191813] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.203292] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory [ 0.204705] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.223283] Serial: AMBA PL011 UART driver [ 0.324242] mxs-dma 110000.dma-apbh: initialized [ 0.348709] vgaarb: loaded [ 0.351775] SCSI subsystem initialized [ 0.353221] usbcore: registered new interface driver usbfs [ 0.353433] usbcore: registered new interface driver hub [ 0.353602] usbcore: registered new device driver usb [ 0.358296] i2c i2c-0: IMX I2C adapter registered [ 0.358351] i2c i2c-0: can't use DMA, using PIO instead. [ 0.360313] i2c i2c-1: IMX I2C adapter registered [ 0.360366] i2c i2c-1: can't use DMA, using PIO instead. [ 0.361709] i2c i2c-2: IMX I2C adapter registered [ 0.361762] i2c i2c-2: can't use DMA, using PIO instead. [ 0.365846] pps_core: LinuxPPS API ver. 1 registered [ 0.365878] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.365957] PTP clock support registered [ 0.366782] EDAC MC: Ver: 3.0.0 [ 0.378171] clocksource: Switched to clocksource mxc_timer1 [ 0.644549] NET: Registered protocol family 2 [ 0.645268] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.648297] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 20480 bytes) [ 0.648448] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.648668] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) [ 0.649944] TCP: Hash tables configured (established 8192 bind 8192) [ 0.650535] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 0.650789] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 0.651466] NET: Registered protocol family 1 [ 0.653488] RPC: Registered named UNIX socket transport module. [ 0.653541] RPC: Registered udp transport module. [ 0.653567] RPC: Registered tcp transport module. [ 0.653594] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.655551] Trying to unpack rootfs image as initramfs... [ 1.878877] Freeing initrd memory: 11192K [ 1.879828] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 1.880790] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 1.888502] Initialise system trusted keyrings [ 1.889543] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 1.917896] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.920666] NFS: Registering the id_resolver key type [ 1.920796] Key type id_resolver registered [ 1.920852] Key type id_legacy registered [ 1.921053] ntfs: driver 2.1.32 [Flags: R/O]. [ 1.928798] Key type asymmetric registered [ 1.928903] Asymmetric key parser 'x509' registered [ 1.929243] bounce: pool size: 64 pages [ 1.929397] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.929477] io scheduler noop registered [ 1.929511] io scheduler deadline registered [ 1.929978] io scheduler cfq registered (default) [ 1.930014] io scheduler mq-deadline registered [ 1.930047] io scheduler kyber registered [ 1.930646] test_firmware: interface ready [ 2.006493] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.007065] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.007945] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.008340] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.054683] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set [ 2.055049] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc [ 2.055224] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set [ 2.055643] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 [ 2.056200] PU : no governor for states [ 2.056271] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc [ 2.080639] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 2.080842] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 2.270925] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 2.283672] SuperH (H)SCI(F) driver initialized [ 2.285898] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX [ 2.288914] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX [ 3.254264] console [ttymxc1] enabled [ 3.262068] msm_serial: driver initialized [ 3.267019] STMicroelectronics ASC driver initialized [ 3.277391] STM32 USART driver initialized [ 3.297002] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 [ 3.321680] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 3.330418] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 3.337427] panel-simple panel-lcd: Dropping the link to regulator.0 [ 3.344259] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 3.353306] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 3.360644] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 3.397279] brd: module loaded [ 3.435734] loop: module loaded [ 3.448892] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 3.456846] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 3.464943] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 3.473201] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 3.484433] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 3.491537] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 3.500427] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.513526] scsi host0: ahci-imx [ 3.518686] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 [ 3.563283] CAN device driver interface [ 3.570724] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 3.579482] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator [ 3.588466] fec 2188000.ethernet: Linked as a consumer to regulator.0 [ 3.598456] pps pps0: new PPS source ptp0 [ 3.637984] fec 2188000.ethernet eth0: registered PHC device 0 [ 3.647132] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 3.653065] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.659228] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 3.666212] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.689031] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 3.696564] usbcore: registered new interface driver pegasus [ 3.702463] usbcore: registered new interface driver asix [ 3.707992] usbcore: registered new interface driver ax88179_178a [ 3.714279] usbcore: registered new interface driver cdc_ether [ 3.720340] usbcore: registered new interface driver smsc75xx [ 3.726259] usbcore: registered new interface driver smsc95xx [ 3.732183] usbcore: registered new interface driver net1080 [ 3.737968] usbcore: registered new interface driver cdc_subset [ 3.744077] usbcore: registered new interface driver zaurus [ 3.749956] usbcore: registered new interface driver cdc_ncm [ 3.764266] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.770880] ehci-pci: EHCI PCI platform driver [ 3.775462] ehci-platform: EHCI generic platform driver [ 3.781570] ehci-orion: EHCI orion driver [ 3.786310] SPEAr-ehci: EHCI SPEAr driver [ 3.791076] ehci-st: EHCI STMicroelectronics driver [ 3.796640] ehci-exynos: EHCI EXYNOS driver [ 3.801557] ehci-atmel: EHCI Atmel driver [ 3.806239] tegra-ehci: Tegra EHCI driver [ 3.811023] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.817328] ohci-pci: OHCI PCI platform driver [ 3.821980] ohci-platform: OHCI generic platform driver [ 3.828016] SPEAr-ohci: OHCI SPEAr driver [ 3.832784] ohci-st: OHCI STMicroelectronics driver [ 3.838418] ohci-atmel: OHCI Atmel driver [ 3.845157] usbcore: registered new interface driver usb-storage [ 3.857599] imx_usb 2184000.usb: Linked as a consumer to regulator.9 [ 3.860760] ata1: SATA link down (SStatus 0 SControl 300) [ 3.869592] ahci-imx 2200000.sata: no device found, disabling link. [ 3.874449] imx_usb 2184200.usb: Linked as a consumer to regulator.14 [ 3.875886] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 3.887485] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 3.894760] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 3.928183] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 3.937688] hub 1-0:1.0: USB hub found [ 3.941892] hub 1-0:1.0: 1 port detected [ 3.968582] i2c /dev entries driver [ 4.020558] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [ 4.041912] sdhci: Secure Digital Host Controller Interface driver [ 4.048183] sdhci: Copyright(c) Pierre Ossman [ 4.058925] Synopsys Designware Multimedia Card Interface Driver [ 4.070972] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.078858] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [ 4.084119] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [ 4.089742] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 [ 4.133359] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 4.141844] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO [ 4.147462] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 [ 4.187155] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [ 4.206264] ledtrig-cpu: registered to indicate activity on CPUs [ 4.214714] usbcore: registered new interface driver usbhid [ 4.220404] usbhid: USB HID core driver [ 4.239245] mmc0: new high speed SDHC card at address aaaa [ 4.242342] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 4.248226] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 4.249464] mmcblk0: mmc0:aaaa SL16G 14.8 GiB [ 4.252037] IPv4 over IPsec tunneling driver [ 4.269736] NET: Registered protocol family 10 [ 4.277957] Segment Routing with IPv6 [ 4.284173] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.294296] NET: Registered protocol family 17 [ 4.299377] can: controller area network core (rev 20170425 abi 9) [ 4.305801] NET: Registered protocol family 29 [ 4.310353] can: raw protocol (rev 20170425) [ 4.314735] can: broadcast manager protocol (rev 20170425 t) [ 4.320555] can: netlink gateway (rev 20170425) max_hops=1 [ 4.326788] 8021q: 802.1Q VLAN Support v1.8 [ 4.331845] Key type dns_resolver registered [ 4.344663] cpu cpu0: Linked as a consumer to regulator.4 [ 4.350496] cpu cpu0: Linked as a consumer to regulator.5 [ 4.356206] cpu cpu0: Linked as a consumer to regulator.6 [ 4.366210] ThumbEE CPU extension supported. [ 4.370607] Registering SWP/SWPB emulation handler [ 4.380847] Loading compiled-in X.509 certificates [ 4.461296] hub 1-1:1.0: USB hub found [ 4.465441] hub 1-1:1.0: 3 ports detected [ 4.468777] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 4.479329] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 4.491020] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 4.498824] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 4.510803] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 4.519607] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 4.526795] panel-simple panel-lcd: Dropping the link to regulator.0 [ 4.537408] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 4.546462] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 4.553874] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 4.567528] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 4.580206] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 4.587601] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 4.595227] GPT:7812499 != 31116287 [ 4.598772] GPT:Alternate GPT header not at the end of the disk. [ 4.604798] GPT:7812499 != 31116287 [ 4.608345] GPT: Use GNU Parted to correct GPT errors. [ 4.613551] mmcblk0: p1 p2 p3 [ 4.617406] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 4.628759] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 4.636873] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 4.648821] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 4.657409] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 4.668948] panel-simple panel-lcd: Dropping the link to regulator.0 [ 4.679675] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 4.688650] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 4.697966] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 4.708218] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 4.715523] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 4.726720] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 4.734165] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 4.745960] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 4.754608] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 4.761579] panel-simple panel-lcd: Dropping the link to regulator.0 [ 4.772423] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 4.781461] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 4.788671] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 4.798781] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 4.806083] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 4.817179] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 4.824619] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 4.836344] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 4.844972] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 4.851945] panel-simple panel-lcd: Dropping the link to regulator.0 [ 4.864481] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 4.872303] hctosys: unable to open rtc device (rtc0) [ 4.882785] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 4.891852] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 4.899132] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 4.909406] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 4.916716] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 4.927906] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 4.935599] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 4.947393] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 4.956036] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 4.963016] panel-simple panel-lcd: Dropping the link to regulator.0 [ 5.011688] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 5.027253] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 8.170209] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 8.178958] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 8.208183] Sending DHCP requests ., OK [ 8.252550] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.36 [ 8.260805] IP-Config: Complete: [ 8.264092] device=eth0, hwaddr=00:19:b8:08:f1:1c, ipaddr=192.168.201.36, mask=255.255.255.0, gw=192.168.201.1 [ 8.274710] host=imx6q-sabrelite-lava-cbg-6, domain=lava-rack, nis-domain=(none) [ 8.282702] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 8.282716] nameserver0=192.168.201.1 [ 8.353541] Freeing unused kernel memory: 2048K [ 8.359163] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 11.289757] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 [ 11.298888] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) [ 11.307586] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 11.315132] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 11.316721] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 11.334521] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 11.336333] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 11.350974] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 11.353058] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 11.357567] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 11.366667] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 11.385805] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 11.393918] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 11.409783] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 11.418504] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 11.428342] panel-simple panel-lcd: Dropping the link to regulator.0 [ 11.484122] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 11.541115] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 11.547252] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 11.557004] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 1 [ 11.567640] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 11.576753] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 11.585839] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 11.598270] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 11.606659] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 11.615978] sgtl5000 0-000a: Linked as a consumer to regulator.7 [ 11.624665] sgtl5000 0-000a: Linked as a consumer to regulator.8 [ 11.632324] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 11.635974] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 11.643382] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 11.657157] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 11.666041] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 11.673097] panel-simple panel-lcd: Dropping the link to regulator.0 [ 11.684052] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 11.693246] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 11.700433] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 11.711462] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 11.779246] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 11.786588] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 11.798347] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 11.806700] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 11.819681] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 11.828482] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 11.837453] panel-simple panel-lcd: Dropping the link to regulator.0 [ 11.848568] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 11.857599] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 11.866056] panel-simple panel-lvds0: Dropping the link to regulator.0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:1c mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.36 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-6 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 13.877610] systemd[1]: System time before build time, advancing clock. [ 13.989815] cgroup: cgroup2: unknown option "memory_recursiveprot" [ 14.034750] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 14.063138] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 14.124508] systemd[1]: Set hostname to . [ 15.662657] systemd[1]: Queued start job for default target Graphical Interface. [ 15.672585] random: systemd: uninitialized urandom read (16 bytes read) [ 15.682464] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 15.719072] random: systemd: uninitialized urandom read (16 bytes read) [ 15.730153] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 15.769092] random: systemd: uninitialized urandom read (16 bytes read) [ 15.780056] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 15.820117] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 15.862140] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 15.911368] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 15.950350] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 15.963191] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 16.009835] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 16.049149] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 16.088975] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 16.128805] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 16.172521] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 16.278494] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 16.291678] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 16.344479] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 16.384863] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 16.440174] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 16.483784] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 16.532341] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 16.542526] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 16.560808] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 16.607777] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 16.737184] random: systemd: uninitialized urandom read (16 bytes read) [ 16.758899] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 16.799571] random: systemd: uninitialized urandom read (16 bytes read) [ 16.815341] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 16.859328] random: systemd: uninitialized urandom read (16 bytes read) [ 16.874849] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 16.918229] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 16.967076] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 16.997895] systemd[1]: Starting Journal Service... Starting Journal Service... [ 17.013143] fuse init (API version 7.27) [ 17.059693] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 17.108691] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 17.166330] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 17.223297] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 17.270772] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 17.325873] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 17.406195] systemd[1]: modprobe@configfs.service: Succeeded. [ 17.415461] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 17.463562] systemd[1]: modprobe@drm.service: Succeeded. [ 17.472262] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. [ 17.493523] systemd[1]: modprobe@fuse.service: Succeeded. [ 17.504962] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. [ 17.553093] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. [ 17.603016] systemd[1]: Finished Remount Root and Kernel File Systems. [ OK ] Finished Remount Root and Kernel File Systems. [ 17.659192] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... [ 17.705916] systemd[1]: Mounting Kernel Configuration File System... Mounting Kernel Configuration File System... [ 17.765730] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. [ 17.775404] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. [ 17.785174] random: systemd: uninitialized urandom read (16 bytes read) [ 17.799071] systemd[1]: Starting Load/Save Random Seed... [ 17.804319] random: systemd-journal: uninitialized urandom read (16 bytes read) Starting Load/Save Random Seed... [ 17.839388] random: systemd: uninitialized urandom read (16 bytes read) [ 17.854946] systemd[1]: Starting Apply Kernel Variables... Starting Apply Kernel Variables... [ 17.896795] systemd[1]: Starting Create System Users... Starting Create System Users... [ 17.934318] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. Starting Flush Journal to Persistent Storage... [ OK ] Finished Create System Users. Starting Create Static [ 18.199160] systemd-journald[166]: Received client request to flush runtime journal. Device Nodes in /dev... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Rule-based Manage…for Device Events and Files... [ 19.239343] random: crng init done [ 19.242892] random: 45 urandom warning(s) missed due to ratelimiting [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.277-cip94 #1 SMP Wed Mar 22 06:50:18 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9726566/extract-nfsrootfs-jkgu1tar' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9726566/extract-nfsrootfs-jkgu1tar' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh [ 35.056523] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 35.064437] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 35.083193] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 35.091214] pwm-backlight backlight-lvds: Dropping the link to regulator.8 export SHELL=/bin/sh[ 35.110977] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 35.120078] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 35.127472] panel-simple panel-lcd: Dropping the link to regulator.0 [ 35.144450] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 35.153885] panel-simple panel-lvds0: Linked as a consumer to regulator.0 / # [ 35.161616] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 35.172938] platform backlight-lcd: deferred probe pending [ 35.179042] platform backlight-lvds: deferred probe pending [ 35.184681] platform panel-lcd: deferred probe pending [ 35.190171] platform panel-lvds0: deferred probe pending . /lava-9726566/environment . /lava-9726566/environment / # /lava-9726566/bin/lava-test-runner /lava-9726566/0 /lava-9726566/bin/lava-test-runner /lava-9726566/0 + export TESTRUN_ID=0_dmesg + cd /lava-9726566/0/tests/0_dmesg + cat uuid + UUID=9726566_1.6.2.4.1 [ 35.901817] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 36.119377] [ 36.268953] [ 36.717723] + set +x[ 36.728688] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-9726566/environment / # . /lava-9726566/environment/lava-9726566/bin/lava-test-runner /lava-9726566/1 / # /lava-9726566/bin/lava-test-runner /lava-9726566/1 + export TESTRUN_ID=1_bootrr + cd /lava-9726566/1/tests/1_bootrr + cat uuid + UUID=9726566_1.6.2.4.5[ 37.461291] + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9726566/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd panel-lvds0 /lava-9726566/1/../bin/lava-test-case [ 38.728590] /lava-9726566/1/../bin/lava-test-case [ 38.882250] [ 38.891448] usb_otg_vbus: disabling [ 38.895128] CAN XCVR: disabling /lava-9726566/1/../bin/lava-test-case [ 38.962148] + set +x [ 39.015905] / #