Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3006 device /dev/ttyimx7d-sdb-1 [115200 N81] (Debian GNU/Linux) U-Boot 2016.03-imx_v2016.03_4.1.15_2.0.0_ga+g0ec2a01 (Nov 11 2016 - 03:13:54 -0600) CPU: Freescale i.MX7D rev1.3 996 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 24C Reset cause: POR Board: i.MX7D SABRESD RevA I2C: ready DRAM: 1 GiB PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11 MMC: FSL_SDHC: 0, FSL_SDHC: 1 Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc0 is current device Net: FEC0 Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => setenv ipaddr 172.16.1.16; setenv serverip 172.16.1.4; setenv ethact FEC0; setenv ethprime FEC setenv ipaddr 172.16.1.16; setenv serverip 172.16.1.4; setenv ethact FEC0; setenv ethprime FEC => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80800000 1181455/tftp-deploy-nx3pmuw1/kernel/zImage tftp 0x80800000 1181455/tftp-deploy-nx3pmuw1/kernel/zImage Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.16 Filename '1181455/tftp-deploy-nx3pmuw1/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################## 1.7 MiB/s done Bytes transferred = 10449408 (9f7200 hex) => tftp 0x86800000 1181455/tftp-deploy-nx3pmuw1/ramdisk/ramdisk.cpio.gz.uboot tftp 0x86800000 1181455/tftp-deploy-nx3pmuw1/ramdisk/ramdisk.cpio.gz.uboot Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.16 Filename '1181455/tftp-deploy-nx3pmuw1/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 10.6 MiB/s done Bytes transferred = 15389890 (ead4c2 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x83000000 1181455/tftp-deploy-nx3pmuw1/dtb/imx7d-sdb.dtb tftp 0x83000000 1181455/tftp-deploy-nx3pmuw1/dtb/imx7d-sdb.dtb Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.16 Filename '1181455/tftp-deploy-nx3pmuw1/dtb/imx7d-sdb.dtb'. Load address: 0x83000000 Loading: *### 4.6 MiB/s done Bytes transferred = 33576 (8328 hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x80800000 0x86800000 0x83000000 bootz 0x80800000 0x86800000 0x83000000 Kernel image @ 0x80800000 [ 0x000000 - 0x9f7200 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15389826 Bytes = 14.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300b327 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.277-cip94 (KernelCI@build-j1225729-arm-gcc-10-multi-v7-defconfig-kselftest-96h2r) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Mar 22 06:50:18 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX7 SabreSD Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x30860000 (options '') [ 0.000000] bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xbc000000 [ 0.000000] percpu: Embedded 17 pages/cpu s40104 r8192 d21336 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 924688K/1048576K available (15360K kernel code, 1762K rwdata, 6312K rodata, 2048K init, 7700K bss, 58352K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (16352 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1763 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7701 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] ftrace: allocating 49054 entries in 192 pages <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns <6>[ 0.000009] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns <6>[ 0.008300] Switching to timer-based delay loop, resolution 125ns <6>[ 0.016037] Switching to timer-based delay loop, resolution 41ns <6>[ 0.020993] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.029128] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.043228] Console: colour dummy device 80x30 <4>[ 0.045139] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.053217] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.057545] ... MAX_LOCK_DEPTH: 48 <4>[ 0.062007] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.066682] ... CLASSHASH_SIZE: 4096 <4>[ 0.071283] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.076007] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.080768] ... CHAINHASH_SIZE: 32768 <4>[ 0.085458] memory used by lock dependency info: 4655 kB <4>[ 0.091181] per task-struct memory footprint: 1536 bytes <6>[ 0.096898] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.107550] pid_max: default: 32768 minimum: 301 <6>[ 0.112779] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.119380] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.128593] CPU: Testing write buffer coherency: ok <6>[ 0.133029] CPU0: update cpu_capacity 1024 <6>[ 0.136212] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.144835] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.151098] rcu: Hierarchical SRCU implementation. <6>[ 0.158525] EFI services will not be available. <6>[ 0.161270] smp: Bringing up secondary CPUs ... <6>[ 0.168265] smp: Brought up 1 node, 1 CPU <6>[ 0.169715] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.176346] CPU: All CPU(s) started in SVC mode. <6>[ 0.183997] devtmpfs: initialized <6>[ 0.222478] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.228737] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.237919] futex hash table entries: 512 (order: 3, 32768 bytes) <6>[ 0.247695] pinctrl core: initialized pinctrl subsystem <6>[ 0.256302] DMI not present or invalid. <6>[ 0.260185] NET: Registered protocol family 16 <6>[ 0.273023] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.285362] cpuidle: using governor menu <6>[ 0.288587] No ATAGs? <6>[ 0.288892] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.297677] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.310400] Serial: AMBA PL011 UART driver <6>[ 0.345617] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver <4>[ 0.353959] imx7d-pinctrl 30330000.iomuxc: Failed to create dummy-iomuxc-gpr@30340000 debugfs directory <6>[ 0.362581] imx7d-pinctrl 30330000.iomuxc: initialized IMX pinctrl driver <6>[ 0.374545] vdd1p0d: Bringing 0uV into 800000-800000uV <6>[ 0.377845] vdd1p0d: supplied by regulator-dummy <6>[ 0.384479] vdd1p2: supplied by regulator-dummy <6>[ 0.572878] mxs-dma 33000000.dma-apbh: initialized <6>[ 0.598331] vgaarb: loaded <5>[ 0.601850] SCSI subsystem initialized <6>[ 0.604823] usbcore: registered new interface driver usbfs <6>[ 0.609199] usbcore: registered new interface driver hub <6>[ 0.614559] usbcore: registered new device driver usb <6>[ 0.624944] i2c i2c-0: IMX I2C adapter registered <6>[ 0.627122] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.635040] i2c i2c-1: IMX I2C adapter registered <6>[ 0.637705] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.644921] i2c i2c-2: IMX I2C adapter registered <6>[ 0.648291] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.656084] i2c i2c-3: IMX I2C adapter registered <6>[ 0.658879] i2c i2c-3: can't use DMA, using PIO instead. <6>[ 0.668680] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.671089] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.680698] PTP clock support registered <6>[ 0.685589] EDAC MC: Ver: 3.0.0 <6>[ 0.701366] clocksource: Switched to clocksource arch_sys_counter <6>[ 1.036677] NET: Registered protocol family 2 <6>[ 1.039067] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 1.047648] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 20480 bytes) <6>[ 1.053746] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 1.061123] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) <6>[ 1.069152] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.074973] UDP hash table entries: 512 (order: 3, 40960 bytes) <6>[ 1.080793] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) <6>[ 1.088064] NET: Registered protocol family 1 <6>[ 1.094904] RPC: Registered named UNIX socket transport module. <6>[ 1.098309] RPC: Registered udp transport module. <6>[ 1.103440] RPC: Registered tcp transport module. <6>[ 1.108274] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.117382] Trying to unpack rootfs image as initramfs... <6>[ 3.037232] Freeing initrd memory: 15032K <6>[ 3.040941] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 3.055227] Initialise system trusted keyrings <6>[ 3.058139] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.102954] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.109945] NFS: Registering the id_resolver key type <5>[ 3.112695] Key type id_resolver registered <5>[ 3.116919] Key type id_legacy registered <6>[ 3.121450] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.135531] Key type asymmetric registered <5>[ 3.137163] Asymmetric key parser 'x509' registered <6>[ 3.142824] bounce: pool size: 64 pages <6>[ 3.146487] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.154196] io scheduler noop registered <6>[ 3.158253] io scheduler deadline registered <6>[ 3.163474] io scheduler cfq registered (default) <6>[ 3.167792] io scheduler mq-deadline registered <6>[ 3.172676] io scheduler kyber registered <4>[ 3.177696] test_firmware: interface ready <4>[ 3.257030] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 3.263504] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 3.271536] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 3.325366] imx7-pgc imx7-pgc-domain.1: DMA mask not set <6>[ 3.328655] imx7-pgc imx7-pgc-domain.1: Linked as a consumer to regulator.1 <4>[ 3.353131] reset_imx7 30390000.src: Failed to create dummy-src@30390000 debugfs directory <4>[ 3.365792] imx-sdma 30bd0000.sdma: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 <6>[ 3.373166] imx-sdma 30bd0000.sdma: external firmware not found, using ROM firmware <6>[ 3.603703] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.621617] SuperH (H)SCI(F) driver ini� 0<6>[ 3.627635] console [ttymxc0] enabled <6>[ 3.627635] console [ttymxc0] enabled <6>[ 3.632764] bootconsole [ec_imx6q0] disabled <6>[ 3.632764] bootconsole [ec_imx6q0] disabled <6>[ 3.645183] 30a80000.serial: ttymxc5 at MMIO 0x30a80000 (irq = 57, base_baud = 15000000) is a IMX <6>[ 3.658884] msm_serial: driver initialized <6>[ 3.664226] STMicroelectronics ASC driver initialized <6>[ 3.674591] STM32 USART driver initialized <6>[ 3.695185] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <6>[ 3.756785] brd: module loaded <6>[ 3.797720] loop: module loaded <6>[ 3.849453] CAN device driver interface <6>[ 3.857122] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 3.868162] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 3.877681] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 3.885167] fec 30be0000.ethernet: Dropping the link to regulator.0 <4>[ 3.895134] fec 30bf0000.ethernet: 30bf0000.ethernet supply phy not found, using dummy regulator <6>[ 3.904631] fec 30bf0000.ethernet: Linked as a consumer to regulator.0 <6>[ 3.913456] pps pps0: new PPS source ptp0 <3>[ 3.920047] fec 30bf0000.ethernet: Invalid MAC address: 00:00:00:00:00:00 <6>[ 3.927434] fec 30bf0000.ethernet: Using random MAC address: ba:f0:75:f2:79:a3 <6>[ 5.152149] fec 30bf0000.ethernet eth0: registered PHC device 0 <6>[ 5.161453] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 5.167580] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 5.174063] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 5.181380] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 5.204065] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 5.212018] usbcore: registered new interface driver pegasus <6>[ 5.218172] usbcore: registered new interface driver asix <6>[ 5.224062] usbcore: registered new interface driver ax88179_178a <6>[ 5.230570] usbcore: registered new interface driver cdc_ether <6>[ 5.236945] usbcore: registered new interface driver smsc75xx <6>[ 5.243231] usbcore: registered new interface driver smsc95xx <6>[ 5.249407] usbcore: registered new interface driver net1080 <6>[ 5.255550] usbcore: registered new interface driver cdc_subset <6>[ 5.262174] usbcore: registered new interface driver zaurus <6>[ 5.268286] usbcore: registered new interface driver cdc_ncm <6>[ 5.282900] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 5.289725] ehci-pci: EHCI PCI platform driver <6>[ 5.294668] ehci-platform: EHCI generic platform driver <6>[ 5.300945] ehci-orion: EHCI orion driver <6>[ 5.306007] SPEAr-ehci: EHCI SPEAr driver <6>[ 5.310948] ehci-st: EHCI STMicroelectronics driver <6>[ 5.316845] ehci-exynos: EHCI EXYNOS driver <6>[ 5.322044] ehci-atmel: EHCI Atmel driver <6>[ 5.326982] tegra-ehci: Tegra EHCI driver <6>[ 5.332032] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 5.338573] ohci-pci: OHCI PCI platform driver <6>[ 5.343510] ohci-platform: OHCI generic platform driver <6>[ 5.349749] SPEAr-ohci: OHCI SPEAr driver <6>[ 5.354762] ohci-st: OHCI STMicroelectronics driver <6>[ 5.360569] ohci-atmel: OHCI Atmel driver <6>[ 5.367671] usbcore: registered new interface driver usb-storage <6>[ 5.400392] i2c /dev entries driver <6>[ 5.453953] imx2-wdt 30280000.wdog: timeout 60 sec (nowayout=0) <6>[ 5.478726] sdhci: Secure Digital Host Controller Interface driver <6>[ 5.485305] sdhci: Copyright(c) Pierre Ossman <6>[ 5.496125] Synopsys Designware Multimedia Card Interface Driver <6>[ 5.508342] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 5.516475] sdhci-esdhc-imx 30b40000.usdhc: Got CD GPIO <6>[ 5.522204] sdhci-esdhc-imx 30b40000.usdhc: Got WP GPIO <6>[ 5.564152] mmc0: SDHCI controller on 30b40000.usdhc [30b40000.usdhc] using ADMA <6>[ 5.574217] sdhci-esdhc-imx 30b50000.usdhc: Linked as a consumer to regulator.6 <6>[ 5.632453] mmc0: new high speed SDHC card at address e624 <6>[ 5.642644] mmcblk0: mmc0:e624 SA16G 14.8 GiB <6>[ 5.653343] mmcblk0: p1 p2 <6>[ 5.833139] mmc1: SDHCI controller on 30b50000.usdhc [30b50000.usdhc] using ADMA <6>[ 5.879769] mmc2: SDHCI controller on 30b60000.usdhc [30b60000.usdhc] using ADMA <6>[ 5.898955] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 5.907761] usbcore: registered new interface driver usbhid <6>[ 5.913710] usbhid: USB HID core driver <6>[ 5.937190] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 5.944999] IPv4 over IPsec tunneling driver <6>[ 5.954291] NET: Registered protocol family 10 <6>[ 5.964241] Segment Routing with IPv6 <6>[ 5.970918] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 5.982164] NET: Registered protocol family 17 <6>[ 5.987206] can: controller area network core (rev 20170425 abi 9) <6>[ 5.993998] NET: Registered protocol family 29 <6>[ 5.998750] can: raw protocol (rev 20170425) <6>[ 6.003454] can: broadcast manager protocol (rev 20170425 t) <6>[ 6.009442] can: netlink gateway (rev 20170425) max_hops=1 <6>[ 6.016149] 8021q: 802.1Q VLAN Support v1.8 <5>[ 6.021619] Key type dns_resolver registered <6>[ 6.033363] ThumbEE CPU extension supported. <5>[ 6.037954] Registering SWP/SWPB emulation handler <4>[ 6.045468] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) <5>[ 6.056134] Loading compiled-in X.509 certificates <4>[ 6.064806] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) <4>[ 6.292382] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 6.301957] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 6.310116] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 6.335701] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 6.345372] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 6.353350] fec 30be0000.ethernet: Dropping the link to regulator.0 <4>[ 6.387756] mmc1: queuing unknown CIS tuple 0x80 (6 bytes) <4>[ 6.404973] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 6.414155] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 6.422461] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 6.447186] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 6.456785] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 6.464848] fec 30be0000.ethernet: Dropping the link to regulator.0 <6>[ 6.503425] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 6.513461] hctosys: unable to open rtc device (rtc0) <4>[ 6.532209] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 6.541412] pwm-backlight backlight: Linked as a consumer to regulator.0 <3>[ 6.562576] fec 30bf0000.ethernet eth0: Unable to connect to phy <3>[ 6.587220] IP-Config: Failed to open eth0 <3>[ 6.591691] IP-Config: No network devices available <6>[ 6.602487] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 6.652430] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 6.662012] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 6.736939] fec 30be0000.ethernet: Dropping the link to regulator.0 <6>[ 6.777481] Freeing unused kernel memory: 2048K <6>[ 6.783501] Run /init as init process <6>[ 6.901067] mmc1: new ultra high speed SDR104 SDIO card at address 0001 Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.413750] udevd[120]: starting version 3.2.9 <5>[ 7.424189] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.432731] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.439689] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.463891] udevd[120]: specified user 'tss' unknown <27>[ 7.469547] udevd[120]: specified group 'tss' unknown <30>[ 7.487475] udevd[121]: starting eudev-3.2.9 <6>[ 11.302005] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 11.308925] [drm] No driver support for vblank timestamp query. <3>[ 11.316024] mxsfb 30730000.lcdif: Failed to create outputs <6>[ 11.416896] flexcan 30a10000.can: Linked as a consumer to regulator.7 <6>[ 11.426428] flexcan 30a10000.can: device registered (reg_base=(ptrval), irq=52) <4>[ 11.445435] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 11.454671] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 11.640819] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 11.876266] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 11.885819] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <5>[ 12.043099] cfg80211: Loading compiled-in X.509 certificates for regulatory database <6>[ 12.096818] fec 30be0000.ethernet: Dropping the link to regulator.0 <6>[ 12.432740] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 12.439666] [drm] No driver support for vblank timestamp query. <3>[ 12.446693] mxsfb 30730000.lcdif: Failed to create outputs <4>[ 12.463054] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 12.472226] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 12.700006] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 12.724470] usb_phy_generic usbphynop1: usbphynop1 supply vcc not found, using dummy regulator <6>[ 12.733818] usb_phy_generic usbphynop1: Linked as a consumer to regulator.0 <4>[ 12.872005] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 12.881611] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 12.941812] fec 30be0000.ethernet: Dropping the link to regulator.0 <6>[ 12.957736] imx_usb 30b10000.usb: Linked as a consumer to regulator.3 <4>[ 12.968215] usb_phy_generic usbphynop3: usbphynop3 supply vcc not found, using dummy regulator <6>[ 12.977572] usb_phy_generic usbphynop3: Linked as a consumer to regulator.0 <4>[ 12.985986] usb_phy_generic usbphynop2: usbphynop2 supply vcc not found, using dummy regulator <6>[ 12.995326] usb_phy_generic usbphynop2: Linked as a consumer to regulator.0 <6>[ 13.209835] imx_usb 30b20000.usb: Linked as a consumer to regulator.4 <6>[ 13.335490] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 13.341629] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 13.401543] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 13.463078] hub 1-0:1.0: USB hub found <6>[ 13.496458] hub 1-0:1.0: 1 port detected <5>[ 13.548310] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <6>[ 13.674460] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 13.681558] [drm] No driver support for vblank timestamp query. <3>[ 13.688163] mxsfb 30730000.lcdif: Failed to create outputs <4>[ 13.704513] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 13.713772] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 13.887276] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 13.966845] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 13.976513] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 14.054911] fec 30be0000.ethernet: Dropping the link to regulator.0 <4>[ 14.108173] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 14.117309] cfg80211: failed to load regulatory.db <6>[ 14.226132] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <6>[ 14.282203] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 14.289123] [drm] No driver support for vblank timestamp query. <3>[ 14.295960] mxsfb 30730000.lcdif: Failed to create outputs <4>[ 14.312215] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 14.321398] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 14.489101] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 14.602113] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 14.611754] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 14.662606] fec 30be0000.ethernet: Dropping the link to regulator.0 <6>[ 14.769448] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 14.776616] [drm] No driver support for vblank timestamp query. <3>[ 14.783288] mxsfb 30730000.lcdif: Failed to create outputs <4>[ 14.857866] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed with error -2 done Saving random seed: <3>[ 15.932184] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 <5>[ 15.961768] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 16.270514] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1181455/environment . /lava-1181455/environment / # /lava-1181455/bin/lava-test-runner /lava-1181455/0 /lava-1181455/bin/lava-test-runner /lava-1181455/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1181455/0/tests/0_dmesg + cat uuid + UUID=1181455_1.5.2.4.1<8>[ 22.300155] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 22.442304] <8>[ 22.568315] <8>[ 22.694700] + set +x <8>[ 22.706933] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1181455/environment / # . /lava-1181455/environment/lava-1181455/bin/lava-test-runner /lava-1181455/1 / # /lava-1181455/bin/lava-test-runner /lava-1181455/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1181455/1/tests/1_bootrr + cat uuid + UUID=1181455_1.5.2.4.5<8>[ 28.588640] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1181455/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto regulator-lcd-3v3 backlight panel 30be0000.ethernet tempmon cpufreq-dt 30730000.lcdif /lava-1181455/1/../bin/lava-test-case <8>[ 29.778512] /lava-1181455/1/../bin/lava-test-case <8>[ 30.912923] /lava-1181455/1/../bin/lava-test-case <8>[ 30.979192] + set +x <8>[ 31.025695] / #