Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.2 (4 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 883156/tftp-deploy-z90jk1p7/kernel/zImage tftp 0x82000000 883156/tftp-deploy-z90jk1p7/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '883156/tftp-deploy-z90jk1p7/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################## 5.1 MiB/s done Bytes transferred = 10449408 (9f7200 hex) => tftp 0x83000000 883156/tftp-deploy-z90jk1p7/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 883156/tftp-deploy-z90jk1p7/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '883156/tftp-deploy-z90jk1p7/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 5.2 MiB/s done Bytes transferred = 15389432 (ead2f8 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 883156/tftp-deploy-z90jk1p7/dtb/am335x-boneblack.dtb tftp 0x88000000 883156/tftp-deploy-z90jk1p7/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '883156/tftp-deploy-z90jk1p7/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *### 4.8 MiB/s done Bytes transferred = 34893 (884d hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-03-22 7:01:53 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15389368 Bytes = 14.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8800b84c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.277-cip94 (KernelCI@build-j1225729-arm-gcc-10-multi-v7-defconfig-kselftest-96h2r) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Mar 22 06:50:18 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omapserial0 at MMIO 0x44e09000 (options '') [ 0.000000] bootconsole [omapserial0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 17 pages/cpu s40104 r8192 d21336 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129540 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) <6>[ 0.000000] Memory: 402756K/522240K available (15360K kernel code, 1762K rwdata, 6312K rodata, 2048K init, 7700K bss, 53948K reserved, 65536K cma-reserved, 0K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xdfe00000 ( 510 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (16352 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1763 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7701 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] ftrace: allocating 49054 entries in 192 pages <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz <6>[ 0.000020] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008263] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018014] OMAP clocksource: timer1 at 24000000 Hz <2>[ 0.027418] timer_probe: no matching timers found <6>[ 0.033134] Console: colour dummy device 80x30 <4>[ 0.037927] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.046161] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.050597] ... MAX_LOCK_DEPTH: 48 <4>[ 0.055110] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.059875] ... CLASSHASH_SIZE: 4096 <4>[ 0.064575] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.069430] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.074213] ... CHAINHASH_SIZE: 32768 <4>[ 0.079067] memory used by lock dependency info: 4655 kB <4>[ 0.084831] per task-struct memory footprint: 1536 bytes <6>[ 0.090729] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.185165] pid_max: default: 32768 minimum: 301 <6>[ 0.190544] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.197547] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.206987] CPU: Testing write buffer coherency: ok <6>[ 0.212396] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.219019] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.226838] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.236035] rcu: Hierarchical SRCU implementation. <6>[ 0.245293] EFI services will not be available. <6>[ 0.250907] smp: Bringing up secondary CPUs ... <6>[ 0.255768] smp: Brought up 1 node, 1 CPU <6>[ 0.260221] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.266846] CPU: All CPU(s) started in SVC mode. <6>[ 0.275041] devtmpfs: initialized <6>[ 0.312571] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.321943] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.332396] futex hash table entries: 256 (order: 2, 16384 bytes) <6>[ 0.343700] pinctrl core: initialized pinctrl subsystem <6>[ 0.355059] DMI not present or invalid. <6>[ 0.361350] NET: Registered protocol family 16 <6>[ 0.375567] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.484267] l4_wkup_cm:clk:0010:0: failed to disable <6>[ 0.537131] cpuidle: using governor menu <6>[ 0.567742] OMAP GPIO hardware version 0.1 <6>[ 0.615192] No ATAGs? <6>[ 0.615211] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 0.643809] Serial: AMBA PL011 UART driver <6>[ 0.720979] edma 49000000.edma: TI EDMA DMA engine driver <6>[ 0.737428] vgaarb: loaded <5>[ 0.743284] SCSI subsystem initialized <6>[ 0.749332] usbcore: registered new interface driver usbfs <6>[ 0.755412] usbcore: registered new interface driver hub <6>[ 0.761296] usbcore: registered new device driver usb <6>[ 0.771639] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.776947] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.786777] PTP clock support registered <6>[ 0.791682] EDAC MC: Ver: 3.0.0 <6>[ 0.806521] clocksource: Switched to clocksource timer1 <6>[ 1.074566] NET: Registered protocol family 2 <6>[ 1.080091] IP idents hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 1.088816] tcp_listen_portaddr_hash hash table entries: 256 (order: 1, 10240 bytes) <6>[ 1.097182] TCP established hash table entries: 4096 (order: 2, 16384 bytes) <6>[ 1.104732] TCP bind hash table entries: 4096 (order: 5, 147456 bytes) <6>[ 1.112372] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 1.119541] UDP hash table entries: 256 (order: 2, 20480 bytes) <6>[ 1.125937] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) <6>[ 1.133254] NET: Registered protocol family 1 <6>[ 1.140919] RPC: Registered named UNIX socket transport module. <6>[ 1.147440] RPC: Registered udp transport module. <6>[ 1.152466] RPC: Registered tcp transport module. <6>[ 1.157744] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.167210] Trying to unpack rootfs image as initramfs... <6>[ 2.726590] Freeing initrd memory: 15032K <6>[ 2.733196] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 2.749399] Initialise system trusted keyrings <6>[ 2.755436] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 2.792155] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.801851] NFS: Registering the id_resolver key type <5>[ 2.807627] Key type id_resolver registered <5>[ 2.812148] Key type id_legacy registered <6>[ 2.816807] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.830388] Key type asymmetric registered <5>[ 2.834963] Asymmetric key parser 'x509' registered <6>[ 2.840623] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 2.848617] io scheduler noop registered <6>[ 2.852854] io scheduler deadline registered <6>[ 2.858120] io scheduler cfq registered (default) <6>[ 2.863164] io scheduler mq-deadline registered <6>[ 2.868154] io scheduler kyber registered <4>[ 2.873317] test_firmware: interface ready <6>[ 2.900174] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 3.154935] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.173691] SuperH (H)SCI(F) driver initialized <6>[ 3.181586] msm_serial: driver initialized <6>[ 3.187032] omap_uart 44e09000.serial: no wakeirq for uart0 <6>[ 3.193392] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 30, base_baud = 3000000) is a OMAP UART0 <6>[ 3.203659] console [ttyO0] enabled <6>[ 3.203659] console [ttyO0] enabled <6>[ 3.211474] bootconsole [omapserial0] disabled <6>[ 3.211474] bootconsole [omapserial0] disabled <6>[ 3.223777] STMicroelectronics ASC driver initialized <6>[ 3.233513] STM32 USART driver initialized <6>[ 3.242961] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 3.258737] random: crng init done <6>[ 3.265038] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <6>[ 3.317294] brd: module loaded <6>[ 3.351267] loop: module loaded <6>[ 3.389573] CAN device driver interface <6>[ 3.396552] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.405782] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 3.412287] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.419046] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 3.426688] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.516566] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 3.524935] davinci_mdio 4a101000.mdio: detected phy mask fffffffe <6>[ 3.566277] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 3.581919] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 3.590343] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 3.597562] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 3.608810] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.617188] usbcore: registered new interface driver pegasus <6>[ 3.623569] usbcore: registered new interface driver asix <6>[ 3.629713] usbcore: registered new interface driver ax88179_178a <6>[ 3.637038] usbcore: registered new interface driver cdc_ether <6>[ 3.643600] usbcore: registered new interface driver smsc75xx <6>[ 3.650178] usbcore: registered new interface driver smsc95xx <6>[ 3.656665] usbcore: registered new interface driver net1080 <6>[ 3.662977] usbcore: registered new interface driver cdc_subset <6>[ 3.669645] usbcore: registered new interface driver zaurus <6>[ 3.675934] usbcore: registered new interface driver cdc_ncm <6>[ 3.688756] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.695898] ehci-pci: EHCI PCI platform driver <6>[ 3.701082] ehci-platform: EHCI generic platform driver <6>[ 3.707512] ehci-orion: EHCI orion driver <6>[ 3.712517] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.717604] ehci-st: EHCI STMicroelectronics driver <6>[ 3.723496] ehci-exynos: EHCI EXYNOS driver <6>[ 3.728760] ehci-atmel: EHCI Atmel driver <6>[ 3.733727] tegra-ehci: Tegra EHCI driver <6>[ 3.738827] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.745683] ohci-pci: OHCI PCI platform driver <6>[ 3.750862] ohci-platform: OHCI generic platform driver <6>[ 3.757295] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.762282] ohci-st: OHCI STMicroelectronics driver <6>[ 3.768272] ohci-atmel: OHCI Atmel driver <6>[ 3.774808] usbcore: registered new interface driver usb-storage <6>[ 3.799491] i2c /dev entries driver <6>[ 3.844358] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.851294] sdhci: Copyright(c) Pierre Ossman <6>[ 3.859806] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 3.869373] omap_hsmmc 48060000.mmc: Got CD GPIO <6>[ 3.876236] omap_hsmmc 48060000.mmc: Linked as a consumer to regulator.1 <6>[ 3.913324] omap_hsmmc 481d8000.mmc: Linked as a consumer to regulator.1 <6>[ 3.948306] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.959360] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.977509] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.988382] usbcore: registered new interface driver usbhid <6>[ 3.994519] usbhid: USB HID core driver <6>[ 4.014244] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.022416] IPv4 over IPsec tunneling driver <6>[ 4.031334] NET: Registered protocol family 10 <6>[ 4.041441] Segment Routing with IPv6 <6>[ 4.048355] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.059413] NET: Registered protocol family 17 <6>[ 4.064796] can: controller area network core (rev 20170425 abi 9) <6>[ 4.071996] NET: Registered protocol family 29 <6>[ 4.077050] can: raw protocol (rev 20170425) <6>[ 4.081940] can: broadcast manager protocol (rev 20170425 t) <6>[ 4.088277] can: netlink gateway (rev 20170425) max_hops=1 <6>[ 4.095160] 8021q: 802.1Q VLAN Support v1.8 <5>[ 4.100847] Key type dns_resolver registered <6>[ 4.111938] ThumbEE CPU extension supported. <5>[ 4.116863] Registering SWP/SWPB emulation handler <3>[ 4.122205] omap_voltage_late_init: Voltage driver support not added <5>[ 4.135855] Loading compiled-in X.509 certificates <6>[ 4.248796] mmc1: new high speed MMC card at address 0001 <6>[ 4.259391] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.265945] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 4.273998] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 4.282520] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (235:0) <6>[ 4.300690] mmcblk1: p1 <6>[ 4.344265] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.353456] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 4.362382] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.489844] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.499413] hctosys: unable to open rtc device (rtc0) <6>[ 4.524060] net eth0: initializing cpsw version 1.12 (0) <6>[ 4.627903] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 4.649511] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 4.655938] 8021q: adding VLAN 0 to HW filter on device eth0 <6>[ 7.797602] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 7.807044] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.836471] Sending DHCP requests ., OK <6>[ 7.880875] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.2 <6>[ 7.889396] IP-Config: Complete: <6>[ 7.893068] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.2, mask=255.255.255.0, gw=192.168.11.1 <6>[ 7.904074] host=192.168.11.2, domain=usen.ad.jp, nis-domain=(none) <6>[ 7.911478] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 7.911486] nameserver0=192.168.11.1 <6>[ 7.986149] Freeing unused kernel memory: 2048K <6>[ 7.992902] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.525274] udevd[84]: starting version 3.2.9 <27>[ 8.551998] udevd[84]: specified user 'tss' unknown <27>[ 8.558705] udevd[84]: specified group 'tss' unknown <30>[ 8.576290] udevd[85]: starting eudev-3.2.9 <4>[ 13.165434] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator <6>[ 13.176698] am335x-phy-driver 47401300.usb-phy: Linked as a consumer to regulator.0 <4>[ 13.378703] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator <6>[ 13.390011] am335x-phy-driver 47401b00.usb-phy: Linked as a consumer to regulator.0 <6>[ 13.630889] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 13.637886] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 13.778286] hub 1-0:1.0: USB hub found <6>[ 13.807950] hub 1-0:1.0: 1 port detected done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-883156/environment . /lava-883156/environment / # /lava-883156/bin/lava-test-runner /lava-883156/0 /lava-883156/bin/lava-test-runner /lava-883156/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-883156/0/tests/0_dmesg + cat uuid + UUID=883156_1.5.2.4.1 + set +x <8>[ 17.300574] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh kern :crit : timer_probe: no matching timers found <8>[ 17.437627] <8>[ 17.555515] <8>[ 17.674815] + set +x <8>[ 17.689251] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-883156/environment / # . /lava-883156/environment/lava-883156/bin/lava-test-runner /lava-883156/1 / # /lava-883156/bin/lava-test-runner /lava-883156/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-883156/1/tests/1_bootrr + cat uuid + UUID=883156_1.5.2.4.5 + set +x <8>[ 18.312587] + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-883156/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto sound /lava-883156/1/../bin/lava-test-case <8>[ 19.493093] /lava-883156/1/../bin/lava-test-case <8>[ 19.608424] /lava-883156/1/../bin/lava-test-case <8>[ 19.672364] /lava-883156/1/../bin/lava-test-case <8>[ 20.818136] /lava-883156/1/../bin/lava-test-case <8>[ 21.919121] /lava-883156/1/../bin/lava-test-case <8>[ 22.003792] /lava-883156/1/../bin/lava-test-case <8>[ 22.115163] /lava-883156/1/../bin/lava-test-case <8>[ 22.225670] /lava-883156/1/../bin/lava-test-case <8>[ 22.311615] /lava-883156/1/../bin/lava-test-case <8>[ 22.421479] /lava-883156/1/../bin/lava-test-case <8>[ 23.521587] /lava-883156/1/../bin/lava-test-case <8>[ 24.623509] /lava-883156/1/../bin/lava-test-case <8>[ 24.685855] /lava-883156/1/../bin/lava-test-case <8>[ 24.748546] /lava-883156/1/../bin/lava-test-case <8>[ 24.833733] /lava-883156/1/../bin/lava-test-case <8>[ 24.941839] /lava-883156/1/../bin/lava-test-case <8>[ 25.027783] /lava-883156/1/../bin/lava-test-case <8>[ 26.153994] /lava-883156/1/../bin/lava-test-case <8>[ 27.278254] /lava-883156/1/../bin/lava-test-case <8>[ 27.363027] /lava-883156/1/../bin/lava-test-case <8>[ 27.474063] /lava-883156/1/../bin/lava-test-case <8>[ 27.585412] /lava-883156/1/../bin/lava-test-case <8>[ 27.672198] /lava-883156/1/../bin/lava-test-case <8>[ 27.783538] /lava-883156/1/../bin/lava-test-case <8>[ 27.868455] /lava-883156/1/../bin/lava-test-case <8>[ 27.979795] /lava-883156/1/../bin/lava-test-case <8>[ 29.080312] /lava-883156/1/../bin/lava-test-case <8>[ 30.181512] /lava-883156/1/../bin/lava-test-case <8>[ 31.282155] /lava-883156/1/../bin/lava-test-case <8>[ 32.384116] /lava-883156/1/../bin/lava-test-case <8>[ 32.470824] /lava-883156/1/../bin/lava-test-case <8>[ 32.579463] /lava-883156/1/../bin/lava-test-case <8>[ 33.680254] /lava-883156/1/../bin/lava-test-case <8>[ 34.780132] /lava-883156/1/../bin/lava-test-case <8>[ 34.865552] /lava-883156/1/../bin/lava-test-case <8>[ 34.977408] <6>[ 35.084225] platform sound: deferred probe pending /lava-883156/1/../bin/lava-test-case <8>[ 36.075301] /lava-883156/1/../bin/lava-test-case <8>[ 37.178016] /lava-883156/1/../bin/lava-test-case <8>[ 38.280281] /lava-883156/1/../bin/lava-test-case <8>[ 39.381058] /lava-883156/1/../bin/lava-test-case <8>[ 40.481017] /lava-883156/1/../bin/lava-test-case <8>[ 41.581890] /lava-883156/1/../bin/lava-test-case <8>[ 42.682109] /lava-883156/1/../bin/lava-test-case <8>[ 43.783465] /lava-883156/1/../bin/lava-test-case <8>[ 44.883160] /lava-883156/1/../bin/lava-test-case <8>[ 45.983509] /lava-883156/1/../bin/lava-test-case <8>[ 47.083697] /lava-883156/1/../bin/lava-test-case <8>[ 48.185096] /lava-883156/1/../bin/lava-test-case <8>[ 49.285418] /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: line 84: assert_device-present: not found /lava-883156/1/../bin/lava-test-case <8>[ 49.374356] /lava-883156/1/../bin/lava-test-case <8>[ 50.500598] /lava-883156/1/../bin/lava-test-case <8>[ 51.595479] + set +x <8>[ 51.623247] / #