Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3023 device /dev/ttyimx6ul-14x14-evk-1 [115200 N81] (Debian GNU/Linux) U-Boot 2019.04-lf-5.4.y_v2019.04+g228843cdf5 (Feb 24 2020 - 11:58:52 +0000) CPU: Freescale i.MX6UL rev1.2 696 MHz (running at 396 MHz) CPU: Automotive temperature grade (-40C to 125C) at 32C Reset cause: POR Model: Freescale i.MX6 UltraLite 14x14 EVK Board Board: MX6UL 14x14 EVK DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc1 is current device flash target is MMC:1 Net: Warning: ethernet@020b4000 using MAC address from ROM eth1: ethernet@020b4000 [PRIME] Warning: ethernet@02188000 using MAC address from ROM , eth0: ethernet@02188000 Fastboot: Normal Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.160 (1255 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80800000 1181456/tftp-deploy-omq0o4n4/kernel/zImage tftp 0x80800000 1181456/tftp-deploy-omq0o4n4/kernel/zImage Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.160; sending through gateway 172.16.1.4 Filename '1181456/tftp-deploy-omq0o4n4/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################## 5 MiB/s done Bytes transferred = 10449408 (9f7200 hex) => tftp 0x86800000 1181456/tftp-deploy-omq0o4n4/ramdisk/ramdisk.cpio.gz.uboot tftp 0x86800000 1181456/tftp-deploy-omq0o4n4/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.160; sending through gateway 172.16.1.4 Filename '1181456/tftp-deploy-omq0o4n4/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 5 MiB/s done Bytes transferred = 15389688 (ead3f8 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x83000000 1181456/tftp-deploy-omq0o4n4/dtb/imx6ul-14x14-evk.dtb tftp 0x83000000 1181456/tftp-deploy-omq0o4n4/dtb/imx6ul-14x14-evk.dtb Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.160; sending through gateway 172.16.1.4 Filename '1181456/tftp-deploy-omq0o4n4/dtb/imx6ul-14x14-evk.dtb'. Load address: 0x83000000 Loading: *## 3.8 MiB/s done Bytes transferred = 27892 (6cf4 hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x80800000 0x86800000 0x83000000 bootz 0x80800000 0x86800000 0x83000000 Kernel image @ 0x80800000 [ 0x000000 - 0x9f7200 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15389624 Bytes = 14.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 83009cf3 ft_system_setup for mx6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.277-cip94 (KernelCI@build-j1225729-arm-gcc-10-multi-v7-defconfig-kselftest-96h2r) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Mar 22 06:50:18 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 UltraLite 14x14 EVK Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x02020000 (options '') [ 0.000000] bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s40104 r8192 d21336 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) <6>[ 0.000000] Memory: 404856K/524288K available (15360K kernel code, 1762K rwdata, 6312K rodata, 2048K init, 7700K bss, 53896K reserved, 65536K cma-reserved, 0K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (16352 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1763 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7701 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] ftrace: allocating 49054 entries in 192 pages <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] Switching to timer-based delay loop, resolution 41ns <6>[ 0.000021] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008106] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.024894] Console: colour dummy device 80x30 <4>[ 0.026871] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.035150] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.039191] ... MAX_LOCK_DEPTH: 48 <4>[ 0.043625] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.048354] ... CLASSHASH_SIZE: 4096 <4>[ 0.052846] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.057546] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.062338] ... CHAINHASH_SIZE: 32768 <4>[ 0.066942] memory used by lock dependency info: 4655 kB <4>[ 0.072694] per task-struct memory footprint: 1536 bytes <6>[ 0.078368] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.088986] pid_max: default: 32768 minimum: 301 <6>[ 0.094590] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.100770] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.112385] CPU: Testing write buffer coherency: ok <3>[ 0.117320] /cpus/cpu@0 missing clock-frequency property <6>[ 0.120474] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.133128] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.141346] rcu: Hierarchical SRCU implementation. <6>[ 0.152326] EFI services will not be available. <6>[ 0.155923] smp: Bringing up secondary CPUs ... <6>[ 0.159347] smp: Brought up 1 node, 1 CPU <6>[ 0.163400] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.169977] CPU: All CPU(s) started in SVC mode. <6>[ 0.181025] devtmpfs: initialized <6>[ 0.241073] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.248379] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.256739] futex hash table entries: 256 (order: 2, 16384 bytes) <6>[ 0.269956] pinctrl core: initialized pinctrl subsystem <6>[ 0.285746] DMI not present or invalid. <6>[ 0.292712] NET: Registered protocol family 16 <6>[ 0.317050] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.338109] cpuidle: using governor menu <6>[ 0.411964] vdd3p0: supplied by regulator-dummy <6>[ 0.418555] cpu: supplied by regulator-dummy <6>[ 0.426282] vddsoc: supplied by regulator-dummy <6>[ 0.527843] No ATAGs? <6>[ 0.528498] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.536795] hw-breakpoint: maximum watchpoint size is 8 bytes. <4>[ 0.568720] imx6ul-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e4000 debugfs directory <6>[ 0.578963] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.614668] Serial: AMBA PL011 UART driver <6>[ 0.851217] mxs-dma 1804000.dma-apbh: initialized <6>[ 0.891000] vgaarb: loaded <5>[ 0.898888] SCSI subsystem initialized <6>[ 0.904518] usbcore: registered new interface driver usbfs <6>[ 0.908098] usbcore: registered new interface driver hub <6>[ 0.913396] usbcore: registered new device driver usb <6>[ 0.930252] i2c i2c-0: IMX I2C adapter registered <6>[ 0.932513] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.943470] i2c i2c-1: IMX I2C adapter registered <6>[ 0.945728] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.959883] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.962563] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.971896] PTP clock support registered <6>[ 0.977944] EDAC MC: Ver: 3.0.0 <6>[ 1.008656] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.745478] NET: Registered protocol family 2 <6>[ 1.748786] IP idents hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 1.758599] tcp_listen_portaddr_hash hash table entries: 256 (order: 1, 10240 bytes) <6>[ 1.764022] TCP established hash table entries: 4096 (order: 2, 16384 bytes) <6>[ 1.771590] TCP bind hash table entries: 4096 (order: 5, 147456 bytes) <6>[ 1.779494] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 1.785480] UDP hash table entries: 256 (order: 2, 20480 bytes) <6>[ 1.791214] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) <6>[ 1.798854] NET: Registered protocol family 1 <6>[ 1.809227] RPC: Registered named UNIX socket transport module. <6>[ 1.812710] RPC: Registered udp transport module. <6>[ 1.817643] RPC: Registered tcp transport module. <6>[ 1.822909] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.834371] Trying to unpack rootfs image as initramfs... <6>[ 6.397065] Freeing initrd memory: 15032K <5>[ 6.415838] Initialise system trusted keyrings <6>[ 6.421372] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 6.508820] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.521140] NFS: Registering the id_resolver key type <5>[ 6.523990] Key type id_resolver registered <5>[ 6.528148] Key type id_legacy registered <6>[ 6.533133] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.562136] Key type asymmetric registered <5>[ 6.563944] Asymmetric key parser 'x509' registered <6>[ 6.569949] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 6.576687] io scheduler noop registered <6>[ 6.580979] io scheduler deadline registered <6>[ 6.586636] io scheduler cfq registered (default) <6>[ 6.590420] io scheduler mq-deadline registered <6>[ 6.594963] io scheduler kyber registered <4>[ 6.601249] test_firmware: interface ready <4>[ 6.755578] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 6.764303] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 6.773661] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 6.922788] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 6.930776] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 7.498480] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 7.534107] SuperH (H)SCI(F) driver initialized <6>[ 7.542584] console [ttymxc0] enabled <6>[ 7.542584] console [ttymxc0] enabled <6>[ 7.547704] bootconsole [ec_imx6q0] disabled <6>[ 7.547704] bootconsole [ec_imx6q0] disabled <6>[ 7.565622] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 61, base_baud = 5000000) is a IMX <6>[ 7.584027] msm_serial: driver initialized <6>[ 7.590724] STMicroelectronics ASC driver initialized <6>[ 7.607000] STM32 USART driver initialized <6>[ 7.647619] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 7.691475] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 7.700483] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 7.709012] panel-simple panel: Dropping the link to regulator.0 <6>[ 7.805867] brd: module loaded <6>[ 7.891854] loop: module loaded <6>[ 7.999942] CAN device driver interface <6>[ 8.011714] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 8.024162] fec 20b4000.ethernet: 20b4000.ethernet supply phy not found, using dummy regulator <6>[ 8.034116] fec 20b4000.ethernet: Linked as a consumer to regulator.0 <6>[ 8.044661] pps pps0: new PPS source ptp0 <6>[ 8.238078] fec 20b4000.ethernet eth0: registered PHC device 0 <4>[ 8.248870] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 8.258956] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 8.269005] pps pps1: new PPS source ptp1 <6>[ 10.989596] fec 2188000.ethernet eth1: registered PHC device 1 <6>[ 11.002223] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 11.008646] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 11.015401] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 11.022900] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 11.065087] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 11.073426] usbcore: registered new interface driver pegasus <6>[ 11.080100] usbcore: registered new interface driver asix <6>[ 11.086186] usbcore: registered new interface driver ax88179_178a <6>[ 11.093154] usbcore: registered new interface driver cdc_ether <6>[ 11.100100] usbcore: registered new interface driver smsc75xx <6>[ 11.106623] usbcore: registered new interface driver smsc95xx <6>[ 11.113240] usbcore: registered new interface driver net1080 <6>[ 11.119801] usbcore: registered new interface driver cdc_subset <6>[ 11.126362] usbcore: registered new interface driver zaurus <6>[ 11.133074] usbcore: registered new interface driver cdc_ncm <6>[ 11.157813] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 11.164963] ehci-pci: EHCI PCI platform driver <6>[ 11.170285] ehci-platform: EHCI generic platform driver <6>[ 11.177604] ehci-orion: EHCI orion driver <6>[ 11.183793] SPEAr-ehci: EHCI SPEAr driver <6>[ 11.189888] ehci-st: EHCI STMicroelectronics driver <6>[ 11.196551] ehci-exynos: EHCI EXYNOS driver <6>[ 11.202815] ehci-atmel: EHCI Atmel driver <6>[ 11.209030] tegra-ehci: Tegra EHCI driver <6>[ 11.214958] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 11.221890] ohci-pci: OHCI PCI platform driver <6>[ 11.227045] ohci-platform: OHCI generic platform driver <6>[ 11.234526] SPEAr-ohci: OHCI SPEAr driver <6>[ 11.240636] ohci-st: OHCI STMicroelectronics driver <6>[ 11.247337] ohci-atmel: OHCI Atmel driver <6>[ 11.258082] usbcore: registered new interface driver usb-storage <4>[ 11.278211] imx_usb 2184000.usb: 2184000.usb supply vbus not found, using dummy regulator <6>[ 11.287738] imx_usb 2184000.usb: Linked as a consumer to regulator.0 <4>[ 11.318909] imx_usb 2184200.usb: 2184200.usb supply vbus not found, using dummy regulator <6>[ 11.328151] imx_usb 2184200.usb: Linked as a consumer to regulator.0 <6>[ 11.345814] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 11.351974] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 11.388616] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 11.405761] hub 1-0:1.0: USB hub found <6>[ 11.411306] hub 1-0:1.0: 1 port detected <6>[ 11.469565] i2c /dev entries driver <6>[ 11.587965] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 11.629443] sdhci: Secure Digital Host Controller Interface driver <6>[ 11.635973] sdhci: Copyright(c) Pierre Ossman <6>[ 11.654653] Synopsys Designware Multimedia Card Interface Driver <6>[ 11.674492] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 11.686380] sdhci-esdhc-imx 2190000.usdhc: Got CD GPIO <6>[ 11.693540] sdhci-esdhc-imx 2190000.usdhc: Linked as a consumer to regulator.4 <6>[ 11.744292] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA <6>[ 11.795273] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA <6>[ 11.831096] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 11.843102] usbcore: registered new interface driver usbhid <6>[ 11.849312] usbhid: USB HID core driver <6>[ 11.895346] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 11.905764] IPv4 over IPsec tunneling driver <6>[ 11.921523] NET: Registered protocol family 10 <6>[ 11.939748] Segment Routing with IPv6 <6>[ 11.950148] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 11.967630] NET: Registered protocol family 17 <6>[ 11.973612] can: controller area network core (rev 20170425 abi 9) <6>[ 11.980993] NET: Registered protocol family 29 <6>[ 11.985836] can: raw protocol (rev 20170425) <6>[ 11.990934] can: broadcast manager protocol (rev 20170425 t) <6>[ 11.997050] can: netlink gateway (rev 20170425) max_hops=1 <6>[ 12.005201] 8021q: 802.1Q VLAN Support v1.8 <5>[ 12.011950] Key type dns_resolver registered <6>[ 12.041376] cpu cpu0: Linked as a consumer to regulator.2 <6>[ 12.047953] cpu cpu0: Linked as a consumer to regulator.3 <6>[ 12.065002] ThumbEE CPU extension supported. <5>[ 12.070008] Registering SWP/SWPB emulation handler <5>[ 12.089896] Loading compiled-in X.509 certificates <4>[ 12.246863] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 12.258438] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 12.267793] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 12.285701] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 12.294496] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 12.302440] panel-simple panel: Dropping the link to regulator.0 <6>[ 12.323981] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 12.341739] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 12.352579] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 12.362185] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 12.379457] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 12.387905] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 12.396030] panel-simple panel: Dropping the link to regulator.0 <4>[ 12.410770] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 12.421722] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <4>[ 12.430054] mmc1: host does not support reading read-only switch, assuming write-enable <6>[ 12.439452] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 12.456701] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 12.465371] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 12.476873] mmc1: new high speed SDHC card at address aaaa <6>[ 12.489725] mmcblk1: mmc1:aaaa SS16G 14.8 GiB <6>[ 12.501034] panel-simple panel: Dropping the link to regulator.0 <6>[ 12.515465] hctosys: unable to open rtc device (rtc0) <6>[ 12.526380] mmcblk1: p1 p2 <4>[ 12.550151] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 12.560972] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 12.569877] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 12.587052] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 12.595733] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 12.603344] panel-simple panel: Dropping the link to regulator.0 <6>[ 12.682316] Micrel KSZ8081 or KSZ8091 20b4000.ethernet-1:01: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=20b4000.ethernet-1:01, irq=POLL) <6>[ 12.700317] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 12.841743] Micrel KSZ8081 or KSZ8091 20b4000.ethernet-1:02: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=20b4000.ethernet-1:02, irq=POLL) <6>[ 12.858662] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready <6>[ 15.855334] fec 20b4000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 15.869147] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 15.888835] Sending DHCP requests ..., OK <6>[ 23.596811] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.160 <6>[ 23.605322] IP-Config: Complete: <6>[ 23.609369] device=eth0, hwaddr=00:04:9f:05:20:41, ipaddr=172.16.1.160, mask=255.255.255.0, gw=172.16.1.4 <6>[ 23.620228] host=172.16.1.160, domain=example.org, nis-domain=(none) <6>[ 23.627431] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 23.627467] nameserver0=172.16.1.4 <6>[ 23.763305] Freeing unused kernel memory: 2048K <6>[ 23.769715] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 24.555092] udevd[117]: starting version 3.2.9 <5>[ 24.565991] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 24.576183] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 24.584038] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 24.617836] udevd[117]: specified user 'tss' unknown <27>[ 24.624837] udevd[117]: specified group 'tss' unknown <30>[ 24.647094] udevd[118]: starting eudev-3.2.9 <4>[ 30.621555] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 30.632437] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 30.871437] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 30.889005] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 30.897445] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 31.042688] panel-simple panel: Dropping the link to regulator.0 <6>[ 31.707531] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 31.714934] [drm] No driver support for vblank timestamp query. <3>[ 31.722352] mxsfb 21c8000.lcdif: Failed to create outputs <6>[ 31.809331] fsl-quadspi 21e0000.qspi: n25q256a (32768 Kbytes) <4>[ 31.911317] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 31.922140] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 32.050837] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 32.068115] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 32.076868] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 32.359833] panel-simple panel: Dropping the link to regulator.0 <6>[ 32.496110] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 32.503466] [drm] No driver support for vblank timestamp query. <3>[ 32.510528] mxsfb 21c8000.lcdif: Failed to create outputs done Saving random seed: <5>[ 36.527980] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 36.947440] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1181456/environment . /lava-1181456/environment / # /lava-1181456/bin/lava-test-runner /lava-1181456/0 /lava-1181456/bin/lava-test-runner /lava-1181456/0 <4>[ 42.824503] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 42.836633] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 42.891041] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 42.934142] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 42.944023] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 43.020530] panel-simple panel: Dropping the link to regulator.0 <6>[ 43.130722] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 43.137797] [drm] No driver support for vblank timestamp query. <3>[ 43.146765] mxsfb 21c8000.lcdif: Failed to create outputs <6>[ 43.249412] platform backlight-display: deferred probe pending <6>[ 43.256464] platform panel: deferred probe pending <6>[ 43.262195] platform 21c8000.lcdif: deferred probe pending <6>[ 43.268117] platform sound: deferred probe pending + export 'TESTRUN_ID=0_dmesg' + cd /lava-1181456/0/tests/0_dmesg + cat uuid + UUID=1181456_1.5.2.4.1 + set +x <8>[ 43.540578] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 43.731219] <8>[ 43.902085] <8>[ 44.071842] + set +x <8>[ 44.086061] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1181456/environment / # . /lava-1181456/environment/lava-1181456/bin/lava-test-runner /lava-1181456/1 / # /lava-1181456/bin/lava-test-runner /lava-1181456/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1181456/1/tests/1_bootrr + cat uuid + UUID=1181456_1.5.2.4.5 + set +x <8>[ 50.059091] + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1181456/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-display panel 21c8000.lcdif sound /lava-1181456/1/../bin/lava-test-case <8>[ 51.340834] /lava-1181456/1/../bin/lava-test-case <8>[ 51.505464] /lava-1181456/1/../bin/lava-test-case <8>[ 51.594767] + set +x <8>[ 51.661519]