[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.101.99 (2 ms) => setenv serverip 192.168.101.1 setenv serverip 192.168.101.1 => tftp 0x10000000 9726586/tftp-deploy-igv185cb/kernel/zImage tftp 0x10000000 9726586/tftp-deploy-igv185cb/kernel/zImage Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.99 Filename '9726586/tftp-deploy-igv185cb/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 2.8 MiB/s done Bytes transferred = 8729088 (853200 hex) => tftp 0x14000000 9726586/tftp-deploy-igv185cb/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9726586/tftp-deploy-igv185cb/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.99 Filename '9726586/tftp-deploy-igv185cb/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 3 MiB/s done Bytes transferred = 9401444 (8f7464 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9726586/tftp-deploy-igv185cb/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9726586/tftp-deploy-igv185cb/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.99 Filename '9726586/tftp-deploy-igv185cb/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 1.9 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/9726586/extract-nfsrootfs-3d9v2znd,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/9726586/extract-nfsrootfs-3d9v2znd,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x853200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9401380 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.277-cip94 (KernelCI@build-j1225715-arm-gcc-10-multi-v7-defconfig-8hxg5) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Mar 22 06:49:40 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/9726586/extract-nfsrootfs-3d9v2znd,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 942980K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 40060K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021424] Console: colour dummy device 80x30 <6>[ 0.023306] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033726] pid_max: default: 32768 minimum: 301 <6>[ 0.038718] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.045468] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.053300] CPU: Testing write buffer coherency: ok <6>[ 0.057913] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.063567] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069813] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077531] rcu: Hierarchical SRCU implementation. <6>[ 0.084077] EFI services will not be available. <6>[ 0.086320] smp: Bringing up secondary CPUs ... <6>[ 0.091582] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091588] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.102925] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.102931] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114105] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114112] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124582] smp: Brought up 1 node, 4 CPUs <6>[ 0.128839] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135255] CPU: All CPU(s) started in SVC mode. <6>[ 0.141215] devtmpfs: initialized <6>[ 0.150807] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156258] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.166011] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175594] pinctrl core: initialized pinctrl subsystem <6>[ 0.179879] DMI not present or invalid. <6>[ 0.183106] NET: Registered protocol family 16 <6>[ 0.190507] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197171] cpuidle: using governor menu <6>[ 0.199161] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.214045] vdd1p1: supplied by regulator-dummy <6>[ 0.216518] vdd3p0: supplied by regulator-dummy <6>[ 0.221248] vdd2p5: supplied by regulator-dummy <6>[ 0.226085] vddarm: supplied by regulator-dummy <6>[ 0.230980] vddpu: supplied by regulator-dummy <6>[ 0.235413] vddsoc: supplied by regulator-dummy <6>[ 0.254008] No ATAGs? <6>[ 0.254155] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.262116] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.271686] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278566] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290609] Serial: AMBA PL011 UART driver <6>[ 0.294487] console [pstore-1] enabled <6>[ 0.296305] pstore: Registered ramoops as persistent store backend <6>[ 0.302554] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.331018] mxs-dma 110000.dma-apbh: initialized <6>[ 0.340610] vgaarb: loaded <5>[ 0.341542] SCSI subsystem initialized <6>[ 0.345133] usbcore: registered new interface driver usbfs <6>[ 0.350573] usbcore: registered new interface driver hub <6>[ 0.356094] usbcore: registered new device driver usb <6>[ 0.362609] i2c i2c-0: IMX I2C adapter registered <6>[ 0.366329] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.372430] i2c i2c-1: IMX I2C adapter registered <6>[ 0.376852] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.382802] i2c i2c-2: IMX I2C adapter registered <6>[ 0.387381] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.394489] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.398158] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.407570] PTP clock support registered <6>[ 0.411959] EDAC MC: Ver: 3.0.0 <6>[ 0.417987] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.482787] NET: Registered protocol family 2 <6>[ 0.485006] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.492533] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.499500] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.506821] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.513608] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.520275] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.526267] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.533030] NET: Registered protocol family 1 <6>[ 0.538036] RPC: Registered named UNIX socket transport module. <6>[ 0.543629] RPC: Registered udp transport module. <6>[ 0.548614] RPC: Registered tcp transport module. <6>[ 0.553545] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.560747] Trying to unpack rootfs image as initramfs... <6>[ 1.286245] Freeing initrd memory: 9184K <4>[ 1.288217] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.295249] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.305297] Initialise system trusted keyrings <6>[ 1.308373] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.320788] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.324662] NFS: Registering the id_resolver key type <5>[ 1.329450] Key type id_resolver registered <5>[ 1.333776] Key type id_legacy registered <6>[ 1.338102] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.344848] Key type asymmetric registered <5>[ 1.347004] Asymmetric key parser 'x509' registered <6>[ 1.352202] bounce: pool size: 64 pages <6>[ 1.356260] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.363899] io scheduler noop registered <6>[ 1.368070] io scheduler deadline registered <6>[ 1.372715] io scheduler cfq registered (default) <6>[ 1.377541] io scheduler mq-deadline registered <6>[ 1.382339] io scheduler kyber registered <6>[ 1.409063] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.413589] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.420733] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.428029] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.448521] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.451912] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.459759] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.465945] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.473900] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 1.478007] PU : no governor for states <6>[ 1.483462] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.487533] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.558841] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.566164] SuperH (H)SCI(F) driver initialized <6>[ 1.569071] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.577734] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.588753] console [ttymxc1] enabled <6>[ 1.588753] console [ttymxc1] enabled <6>[ 1.593735] bootconsole [ec_imx21] disabled <6>[ 1.593735] bootconsole [ec_imx21] disabled <6>[ 1.603872] msm_serial: driver initialized <6>[ 1.610112] STMicroelectronics ASC driver initialized <6>[ 1.617286] STM32 USART driver initialized <4>[ 1.632774] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 1.641477] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 1.648450] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 1.655202] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 1.664231] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 1.671391] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 1.686014] brd: module loaded <6>[ 1.699018] loop: module loaded <6>[ 1.705711] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 1.713965] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 1.722265] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 1.730733] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 1.741524] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 1.748814] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 1.757874] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 1.768692] scsi host0: ahci-imx <6>[ 1.772756] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 1.792013] CAN device driver interface <6>[ 1.797391] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 1.804514] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 1.813475] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 1.822574] pps pps0: new PPS source ptp0 <6>[ 1.844551] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 1.852009] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 1.858127] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.864373] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 1.871616] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.883480] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 1.891209] usbcore: registered new interface driver pegasus <6>[ 1.897183] usbcore: registered new interface driver asix <6>[ 1.902906] usbcore: registered new interface driver ax88179_178a <6>[ 1.909313] usbcore: registered new interface driver cdc_ether <6>[ 1.915454] usbcore: registered new interface driver smsc75xx <6>[ 1.921526] usbcore: registered new interface driver smsc95xx <6>[ 1.927572] usbcore: registered new interface driver net1080 <6>[ 1.933546] usbcore: registered new interface driver cdc_subset <6>[ 1.939784] usbcore: registered new interface driver zaurus <6>[ 1.945692] usbcore: registered new interface driver cdc_ncm <6>[ 1.954639] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.961467] ehci-pci: EHCI PCI platform driver <6>[ 1.966216] ehci-platform: EHCI generic platform driver <6>[ 1.972043] ehci-orion: EHCI orion driver <6>[ 1.976549] SPEAr-ehci: EHCI SPEAr driver <6>[ 1.981049] ehci-st: EHCI STMicroelectronics driver <6>[ 1.986390] ehci-exynos: EHCI EXYNOS driver <6>[ 1.991050] ehci-atmel: EHCI Atmel driver <6>[ 1.995508] tegra-ehci: Tegra EHCI driver <6>[ 2.000034] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.006495] ohci-pci: OHCI PCI platform driver <6>[ 2.011266] ohci-platform: OHCI generic platform driver <6>[ 2.017023] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.021514] ohci-st: OHCI STMicroelectronics driver <6>[ 2.026860] ohci-atmel: OHCI Atmel driver <6>[ 2.032165] usbcore: registered new interface driver usb-storage <6>[ 2.040752] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.052748] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.062914] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.068110] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.098013] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.104343] hub 1-0:1.0: USB hub found <6>[ 2.108425] hub 1-0:1.0: 1 port detected <6>[ 2.119081] i2c /dev entries driver <6>[ 2.137627] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.149181] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.155630] sdhci: Copyright(c) Pierre Ossman <6>[ 2.162579] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.170921] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.177715] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.183184] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.188694] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.228574] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.236589] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.242129] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.278019] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) <6>[ 2.281953] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.284817] ata1.00: ATA-8: INTEL SSDSA2CW080G3, 4PC10362, max UDMA/133 <6>[ 2.298886] ata1.00: 156301488 sectors, multi 1: LBA48 NCQ (depth 32) <6>[ 2.305654] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.305821] mmc0: new high speed SDHC card at address 0001 <6>[ 2.312042] ata1.00: configured for UDMA/133 <6>[ 2.312802] usbcore: registered new interface driver usbhid <6>[ 2.312805] usbhid: USB HID core driver <6>[ 2.319037] NET: Registered protocol family 10 <6>[ 2.319595] mmcblk0: mmc0:0001 SD 14.6 GiB <5>[ 2.338759] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2CW08 0362 PQ: 0 ANSI: 5 <6>[ 2.342669] Segment Routing with IPv6 <6>[ 2.350465] ata1.00: Enabling discard_zeroes_data <6>[ 2.353819] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <5>[ 2.358907] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB) <6>[ 2.365510] NET: Registered protocol family 17 <5>[ 2.372903] sd 0:0:0:0: [sda] Write Protect is off <6>[ 2.377578] can: controller area network core (rev 20170425 abi 9) <5>[ 2.389167] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6>[ 2.389179] NET: Registered protocol family 29 <6>[ 2.398920] ata1.00: Enabling discard_zeroes_data <6>[ 2.403213] can: raw protocol (rev 20170425) <6>[ 2.412760] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.412822] sda: sda1 sda2 sda3 <6>[ 2.418717] can: netlink gateway (rev 20170425) max_hops=1 <6>[ 2.423223] ata1.00: Enabling discard_zeroes_data <5>[ 2.428435] Key type dns_resolver registered <5>[ 2.433241] sd 0:0:0:0: [sda] Attached SCSI disk <6>[ 2.443238] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.448983] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.454719] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.461224] ThumbEE CPU extension supported. <5>[ 2.465776] Registering SWP/SWPB emulation handler <6>[ 2.468014] usb 1-1: new high-speed USB device number 2 using ci_hdrc <5>[ 2.478038] Loading compiled-in X.509 certificates <6>[ 2.484731] pstore: Using compression: deflate <6>[ 2.505365] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.512889] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.521714] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.529258] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.538319] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.546992] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.554015] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.562211] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.571273] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.578465] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.587453] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 2.587577] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 2.598144] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <4>[ 2.604820] GPT:29296874 != 30560255 <6>[ 2.612241] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <4>[ 2.615967] GPT:Alternate GPT header not at the end of the disk. <6>[ 2.624511] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <4>[ 2.629303] GPT:29296874 != 30560255 <4>[ 2.629306] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.629361] mmcblk0: p1 p2 p3 <6>[ 2.636814] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.658395] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.667065] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.674055] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.682205] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.691264] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.698422] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.705784] hub 1-1:1.0: USB hub found <6>[ 2.706453] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.717189] hub 1-1:1.0: 3 ports detected <6>[ 2.717215] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.730081] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.737546] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.746434] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.755150] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.762119] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.770194] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.779231] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.786349] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.794258] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.801646] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.810901] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.818470] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.828922] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.837671] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.844829] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.852712] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.861800] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.868938] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.876649] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.884025] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.892903] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 2.899830] hctosys: unable to open rtc device (rtc0) <6>[ 2.910197] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.917646] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.926420] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.935105] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.942057] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.949911] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.958938] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.966046] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.973760] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.981131] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.038844] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 3.053799] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 5.118654] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 5.128077] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.158138] Sending DHCP requests ., OK <6>[ 5.202225] IP-Config: Got DHCP answer from 192.168.101.1, my address is 192.168.101.99 <6>[ 5.210533] IP-Config: Complete: <6>[ 5.214035] device=eth0, hwaddr=00:19:b8:07:40:03, ipaddr=192.168.101.99, mask=255.255.255.0, gw=192.168.101.1 <6>[ 5.224757] host=imx6q-sabrelite-cbg-0, domain=lava.cbg.collabora.co.uk, nis-domain=(none) <6>[ 5.233742] bootserver=192.168.101.1, rootserver=192.168.101.1, rootpath= <6>[ 5.233747] nameserver0=192.168.101.1 <6>[ 5.251790] Freeing unused kernel memory: 2048K <6>[ 5.288668] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 <6>[ 6.099870] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.107376] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 6.108634] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.114590] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 6.128981] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <4>[ 6.132516] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.137615] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.145541] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.160186] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 6.170247] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <4>[ 6.171985] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.177059] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 6.186118] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.199623] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.207804] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.215223] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.224106] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.231604] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.240783] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.249555] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.256622] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 6.288026] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <4>[ 6.299177] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.308332] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.317713] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.327284] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 6.333718] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 6.340246] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.347635] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.349982] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 6.356344] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.365617] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 6.367452] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.369414] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.391227] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.398258] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 6.408982] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 6.415373] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 6.425773] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <4>[ 6.430735] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.442894] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.450354] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.458898] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.467010] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.475906] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.483509] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.493363] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.502158] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.509166] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.518398] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.527588] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.534896] panel-simple panel-lvds0: Dropping the link to regulator.0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:07:40:03 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.101.1): address: 192.168.101.99 broadcast: 192.168.101.255 netmask: 255.255.255.0 gateway: 192.168.101.1 dns0 : 192.168.101.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-cbg-0 domain : lava.cbg.collabora.co.uk rootserver: 192.168.101.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 9.061227] systemd[1]: System time before build time, advancing clock. <3>[ 9.121356] cgroup: cgroup2: unknown option "memory_recursiveprot" <30>[ 9.138680] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 9.163162] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 9.200688] systemd[1]: Set hostname to . <30>[ 10.091185] systemd[1]: Queued start job for default target Graphical Interface. <5>[ 10.101100] random: systemd: uninitialized urandom read (16 bytes read) <28>[ 10.108186] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 10.120996] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 10.130501] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <5>[ 10.168371] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.176370] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <5>[ 10.218277] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.226256] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 10.269091] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 10.308484] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 10.348869] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 10.388675] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 10.401264] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 10.438911] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 10.468605] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 10.508472] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 10.538555] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 10.569415] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 10.653889] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 10.664095] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 10.699751] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 10.739982] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 10.781716] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 10.819556] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 10.859450] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 10.869032] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 10.881524] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 10.921776] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 11.067538] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <5>[ 11.110131] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 11.124537] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <5>[ 11.158613] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 11.168713] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <5>[ 11.208607] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 11.218770] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 11.262963] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 11.279319] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 11.315106] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 11.352529] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 11.391348] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 11.434653] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <5>[ 11.448025] random: crng init done <5>[ 11.451712] random: 22 urandom warning(s) missed due to ratelimiting <30>[ 11.469454] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 11.509598] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 11.574655] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 11.581597] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 11.618837] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... <46>[ 11.884879] systemd-journald[163]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Create Volatile Files and Directories. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Network Name Resolution. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.277-cip94 #1 SMP Wed Mar 22 06:49:40 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9726586/extract-nfsrootfs-3d9v2znd' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9726586/extract-nfsrootfs-3d9v2znd' / # export NFS_SERVER_IP='192.168.101.1' export NFS_SERVER_IP='192.168.101.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9726586/environment . /lava-9726586/environment / # /lava-9726586/bin/lava-test-runner /lava-9726586/0 /lava-9726586/bin/lava-test-runner /lava-9726586/0 + export TESTRUN_ID=0_dmesg + cd /lava-9726586/0/tests/0_dmesg + cat uuid + UUID=9726586_1.6.2.4.1 + set +x<8>[ 28.483264] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 28.590219] <8>[ 28.667034] <8>[ 28.744418] + set +x <8>[ 28.754018] # / # #export SHELL=/bin/sh / # export SHELL=/bin/sh. /lava-9726586/environment / # . /lava-9726586/environment/lava-9726586/bin/lava-test-runner /lava-9726586/1 / # /lava-9726586/bin/lava-test-runner /lava-9726586/1 + export TESTRUN_ID=1_bootrr + cd /lava-9726586/1/tests/1_bootrr + cat uuid + UUID=9726586_1.6.2.4.5 + set +x<8>[ 29.342193] + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9726586/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd panel-lvds0 /lava-9726586/1/../bin/lava-test-case <8>[ 30.497940] /lava-9726586/1/../bin/lava-test-case <8>[ 30.587291] /lava-9726586/1/../bin/lava-test-case <8>[ 30.637756] + set +x <8>[ 30.672695] / #