[Enter `^Ec?' for help]  U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.36 (5 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9975232/tftp-deploy-7jcrgs5w/kernel/zImage tftp 0x10000000 9975232/tftp-deploy-7jcrgs5w/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9975232/tftp-deploy-7jcrgs5w/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 11 MiB/s done Bytes transferred = 10424832 (9f1200 hex) => tftp 0x14000000 9975232/tftp-deploy-7jcrgs5w/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9975232/tftp-deploy-7jcrgs5w/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9975232/tftp-deploy-7jcrgs5w/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####### 5.8 MiB/s done Bytes transferred = 15368297 (ea8069 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9975232/tftp-deploy-7jcrgs5w/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9975232/tftp-deploy-7jcrgs5w/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9975232/tftp-deploy-7jcrgs5w/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.3 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x9f1200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15368233 Bytes = 14.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.280-cip96 (KernelCI@build-j1346709-arm-gcc-10-multi-v7-defconfig-kselftest-vr5cs) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Fri Apr 14 09:46:15 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s40104 r8192 d21336 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 924532K/1048576K available (15360K kernel code, 1762K rwdata, 6312K rodata, 2048K init, 7700K bss, 58508K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (16352 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1763 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7701 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 49054 entries in 192 pages <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022077] Console: colour dummy device 80x30 <4>[ 0.023965] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.031989] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.036334] ... MAX_LOCK_DEPTH: 48 <4>[ 0.040742] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.045353] ... CLASSHASH_SIZE: 4096 <4>[ 0.049992] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.054663] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.059387] ... CHAINHASH_SIZE: 32768 <4>[ 0.064059] memory used by lock dependency info: 4655 kB <4>[ 0.069740] per task-struct memory footprint: 1536 bytes <6>[ 0.075419] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.085842] pid_max: default: 32768 minimum: 301 <6>[ 0.090996] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.097612] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.106613] CPU: Testing write buffer coherency: ok <6>[ 0.110000] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.116442] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.123468] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.130305] rcu: Hierarchical SRCU implementation. <6>[ 0.137465] EFI services will not be available. <6>[ 0.140364] smp: Bringing up secondary CPUs ... <6>[ 0.146629] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.146642] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.158285] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.158298] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.169169] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.169180] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.178321] smp: Brought up 1 node, 4 CPUs <6>[ 0.182262] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.188769] CPU: All CPU(s) started in SVC mode. <6>[ 0.196423] devtmpfs: initialized <6>[ 0.230855] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.238517] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.246182] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.256504] pinctrl core: initialized pinctrl subsystem <6>[ 0.264064] DMI not present or invalid. <6>[ 0.267309] NET: Registered protocol family 16 <6>[ 0.278448] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.289097] cpuidle: using governor menu <6>[ 0.290894] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.330659] vdd1p1: supplied by regulator-dummy <6>[ 0.334588] vdd3p0: supplied by regulator-dummy <6>[ 0.339253] vdd2p5: supplied by regulator-dummy <6>[ 0.343945] vddarm: supplied by regulator-dummy <6>[ 0.349461] vddpu: supplied by regulator-dummy <6>[ 0.352968] vddsoc: supplied by regulator-dummy <6>[ 0.404838] No ATAGs? <6>[ 0.405327] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.413393] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.430636] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.438645] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.462446] Serial: AMBA PL011 UART driver <6>[ 0.561207] mxs-dma 110000.dma-apbh: initialized <6>[ 0.587265] vgaarb: loaded <5>[ 0.590241] SCSI subsystem initialized <6>[ 0.592810] usbcore: registered new interface driver usbfs <6>[ 0.597423] usbcore: registered new interface driver hub <6>[ 0.602856] usbcore: registered new device driver usb <6>[ 0.612701] i2c i2c-0: IMX I2C adapter registered <6>[ 0.614855] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.622293] i2c i2c-1: IMX I2C adapter registered <6>[ 0.625379] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.632269] i2c i2c-2: IMX I2C adapter registered <6>[ 0.635958] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.645412] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.647850] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.657293] PTP clock support registered <6>[ 0.662178] EDAC MC: Ver: 3.0.0 <6>[ 0.675546] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.940700] NET: Registered protocol family 2 <6>[ 0.943162] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.952314] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 20480 bytes) <6>[ 0.957698] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.964979] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) <6>[ 0.972903] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.978770] UDP hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.984573] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.991656] NET: Registered protocol family 1 <6>[ 0.997505] RPC: Registered named UNIX socket transport module. <6>[ 1.001779] RPC: Registered udp transport module. <6>[ 1.006822] RPC: Registered tcp transport module. <6>[ 1.011691] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.020385] Trying to unpack rootfs image as initramfs... <6>[ 2.786889] Freeing initrd memory: 15012K <4>[ 2.788990] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 2.796579] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 2.811564] Initialise system trusted keyrings <6>[ 2.814243] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.847311] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.853169] NFS: Registering the id_resolver key type <5>[ 2.856100] Key type id_resolver registered <5>[ 2.860328] Key type id_legacy registered <6>[ 2.864743] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.876662] Key type asymmetric registered <5>[ 2.878261] Asymmetric key parser 'x509' registered <6>[ 2.883576] bounce: pool size: 64 pages <6>[ 2.887594] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 2.895113] io scheduler noop registered <6>[ 2.899294] io scheduler deadline registered <6>[ 2.904195] io scheduler cfq registered (default) <6>[ 2.908777] io scheduler mq-deadline registered <6>[ 2.913510] io scheduler kyber registered <4>[ 2.918378] test_firmware: interface ready <6>[ 2.996642] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.001661] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.009072] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.015930] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.067870] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 3.071541] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 3.079247] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 3.085655] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 3.093553] PU : no governor for states <6>[ 3.097235] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <4>[ 3.128790] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.135982] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.320607] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.336796] SuperH (H)SCI(F) driver initialized <6>[ 3.340912] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 3.350370] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 3.359575] console [ttymxc1] enabled <6>[ 3.359575] console [ttymxc1] enabled <6>[ 3.364595] bootconsole [ec_imx21] disabled <6>[ 3.364595] bootconsole [ec_imx21] disabled <6>[ 3.377540] msm_serial: driver initialized <6>[ 3.382749] STMicroelectronics ASC driver initialized <6>[ 3.393215] STM32 USART driver initialized <6>[ 3.413224] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 3.437709] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.446674] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.453929] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.461003] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.470276] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.477844] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.513330] brd: module loaded <6>[ 3.550804] loop: module loaded <6>[ 3.563895] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.572164] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.580513] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.589021] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 3.600481] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.607835] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.616977] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.630004] scsi host0: ahci-imx <6>[ 3.635298] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 3.679608] CAN device driver interface <6>[ 3.687240] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 3.696185] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 3.705340] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 3.715581] pps pps0: new PPS source ptp0 <6>[ 3.763343] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.772688] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 3.778859] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.785227] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 3.792534] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.815163] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.823013] usbcore: registered new interface driver pegasus <6>[ 3.829146] usbcore: registered new interface driver asix <6>[ 3.834947] usbcore: registered new interface driver ax88179_178a <6>[ 3.841480] usbcore: registered new interface driver cdc_ether <6>[ 3.847788] usbcore: registered new interface driver smsc75xx <6>[ 3.853958] usbcore: registered new interface driver smsc95xx <6>[ 3.860133] usbcore: registered new interface driver net1080 <6>[ 3.866244] usbcore: registered new interface driver cdc_subset <6>[ 3.872549] usbcore: registered new interface driver zaurus <6>[ 3.878894] usbcore: registered new interface driver cdc_ncm <6>[ 3.893341] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.900209] ehci-pci: EHCI PCI platform driver <6>[ 3.905048] ehci-platform: EHCI generic platform driver <6>[ 3.911410] ehci-orion: EHCI orion driver <6>[ 3.916456] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.921412] ehci-st: EHCI STMicroelectronics driver <6>[ 3.927285] ehci-exynos: EHCI EXYNOS driver <6>[ 3.932396] ehci-atmel: EHCI Atmel driver <6>[ 3.937399] tegra-ehci: Tegra EHCI driver <6>[ 3.942388] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.948953] ohci-pci: OHCI PCI platform driver <6>[ 3.953796] ohci-platform: OHCI generic platform driver <6>[ 3.960097] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.965062] ohci-st: OHCI STMicroelectronics driver <6>[ 3.970928] ohci-atmel: OHCI Atmel driver <6>[ 3.977758] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.977933] usbcore: registered new interface driver usb-storage <6>[ 3.983571] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.996197] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 3.996432] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.015532] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 4.027360] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.032731] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.065553] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.075028] hub 1-0:1.0: USB hub found <6>[ 4.079466] hub 1-0:1.0: 1 port detected <6>[ 4.106026] i2c /dev entries driver <6>[ 4.157210] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 4.178673] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.185141] sdhci: Copyright(c) Pierre Ossman <6>[ 4.196081] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.208287] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.216351] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 4.221868] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 4.227747] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 4.270566] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 4.279337] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 4.285218] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 4.326222] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 4.345614] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.354277] usbcore: registered new interface driver usbhid <6>[ 4.360269] usbhid: USB HID core driver <6>[ 4.372050] mmc0: new high speed SDHC card at address aaaa <6>[ 4.381844] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.382295] mmcblk0: mmc0:aaaa SL16G 14.8 GiB <6>[ 4.389292] IPv4 over IPsec tunneling driver <6>[ 4.395568] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.400787] NET: Registered protocol family 10 <6>[ 4.413036] Segment Routing with IPv6 <6>[ 4.419455] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.429738] NET: Registered protocol family 17 <6>[ 4.434799] can: controller area network core (rev 20170425 abi 9) <6>[ 4.441546] NET: Registered protocol family 29 <6>[ 4.446351] can: raw protocol (rev 20170425) <6>[ 4.451000] can: broadcast manager protocol (rev 20170425 t) <6>[ 4.457024] can: netlink gateway (rev 20170425) max_hops=1 <6>[ 4.463551] 8021q: 802.1Q VLAN Support v1.8 <5>[ 4.468923] Key type dns_resolver registered <4>[ 4.485539] ------------[ cut here ]------------ <6>[ 4.486620] cpu cpu0: Linked as a consumer to regulator.4 <4>[ 4.490444] WARNING: CPU: 1 PID: 0 at include/trace/events/lock.h:13 lock_acquire+0x138/0x1f0 <4>[ 4.490452] Modules linked in: <6>[ 4.496503] cpu cpu0: Linked as a consumer to regulator.5 <4>[ 4.504905] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.19.280-cip96 #1 <4>[ 4.504915] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <6>[ 4.508565] cpu cpu0: Linked as a consumer to regulator.6 <4>[ 4.513889] Backtrace: <6>[ 4.525401] ThumbEE CPU extension supported. <4>[ 4.525522] ------------[ cut here ]------------ <4>[ 4.525541] WARNING: CPU: 3 PID: 0 at include/trace/events/lock.h:58 lock_release+0x364/0x370 <4>[ 4.525545] Modules linked in: <4>[ 4.527573] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 4.527584] r7:ffffffff r6:00000000 r5:60000093 r4:c1c9d66c <5>[ 4.533273] Registering SWP/SWPB emulation handler <4>[ 4.535963] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 4.535976] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <4>[ 4.535987] r9:60000093 r8:c1b084bc r7:00000000 r6:00000009 r5:00000000 r4:00000000 <4>[ 4.535999] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 4.536007] r6:c03b8c3c r5:0000000d r4:c16816b0 <4>[ 4.612999] [] (warn_slowpath_null) from [] (lock_acquire+0x138/0x1f0) <4>[ 4.621550] r6:00000000 r5:00000000 r4:c1b05990 <4>[ 4.626470] [] (lock_acquire) from [] (_raw_spin_lock+0x58/0x68) <4>[ 4.634503] r10:ef7ab2f8 r9:ef7ab2f8 r8:00000001 r7:ef7af740 r6:00000001 r5:c23e9aec <4>[ 4.642612] r4:c1b05980 <4>[ 4.645445] [] (_raw_spin_lock) from [] (__tick_broadcast_oneshot_control+0x4c/0x2ac) <4>[ 4.655291] r4:ee9d7ee8 <4>[ 4.658117] [] (__tick_broadcast_oneshot_control) from [] (tick_broadcast_oneshot_control+0x3c/0x40) <4>[ 4.669273] r9:ef7ab2f8 r8:00000001 r7:c1b10e94 r6:c1b10ea4 r5:c1b10e44 r4:00000001 <4>[ 4.677311] [] (tick_broadcast_oneshot_control) from [] (cpuidle_enter_state+0x50/0x520) <4>[ 4.687425] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 4.695977] r10:ef7ab2f8 r9:c1b10e44 r8:c1aa22f0 r7:c1b08500 r6:c1b10e44 r5:ef7ab2f8 <4>[ 4.704084] r4:00000001 <4>[ 4.706920] [] (cpuidle_enter) from [] (do_idle+0x20c/0x2f8) <4>[ 4.714602] r7:c1b08500 r6:c1b084bc r5:00000001 r4:ee9d6000 <4>[ 4.720556] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 4.728414] r10:00000000 r9:412fc09a r8:1020406a r7:c1cb9650 r6:00000001 r5:ee9d6000 <4>[ 4.736522] r4:0000008a <4>[ 4.739359] [] (cpu_startup_entry) from [] (secondary_start_kernel+0x170/0x17c) <4>[ 4.748695] [] (secondary_start_kernel) from [<1030312c>] (0x1030312c) <4>[ 4.756378] r7:c1cb9650 r6:10c0387d r5:00000051 r4:3e9c406a <4>[ 4.762315] irq event stamp: 19914 <4>[ 4.762328] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.19.280-cip96 #1 <4>[ 4.762341] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 4.766021] hardirqs last enabled at (19913): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 4.766051] hardirqs last disabled at (19914): [] do_idle+0xb0/0x2f8 <4>[ 4.772917] Backtrace: <4>[ 4.779728] softirqs last enabled at (19906): [] __do_softirq+0x344/0x520 <4>[ 4.788870] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 4.796363] softirqs last disabled at (19891): [] irq_exit+0x170/0x1c8 <4>[ 4.799058] r7:ffffffff r6:00000000 r5:60000093 r4:c1c9d66c <4>[ 4.807064] ---[ end trace 96c5c45a3e13713b ]--- <4>[ 4.814919] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 4.840949] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <4>[ 4.848721] r9:c03ff708 r8:00000003 r7:60000093 r6:00000009 r5:00000000 r4:00000000 <4>[ 4.856756] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 4.865215] r6:c03b8af8 r5:0000003a r4:c16816b0 <4>[ 4.870126] [] (warn_slowpath_null) from [] (lock_release+0x364/0x370) <4>[ 4.878672] r6:c1b456c4 r5:c1b456c4 r4:c1b084bc <4>[ 4.883583] [] (lock_release) from [] (ktime_get+0x84/0x1ac) <4>[ 4.891268] r10:00000001 r9:60000093 r8:00000003 r7:c1b45700 r6:c1b456c4 r5:c03ff708 <4>[ 4.899375] r4:c1b45600 <4>[ 4.902202] [] (ktime_get) from [] (clockevents_program_event+0x6c/0x184) <4>[ 4.911014] r10:ef7cd2f8 r9:c23e9b00 r8:00000003 r7:0e025080 r6:00000001 r5:00000001 <4>[ 4.919121] r4:ee829c40 <4>[ 4.921946] [] (clockevents_program_event) from [] (tick_broadcast_set_event+0x54/0xb4) <4>[ 4.931970] r7:0e025080 r6:00000001 r5:00000003 r4:ee829c40 <4>[ 4.937922] [] (tick_broadcast_set_event) from [] (__tick_broadcast_oneshot_control+0x140/0x2ac) <4>[ 4.948727] r7:ef7d1740 r6:ee829c40 r5:00000000 r4:00000003 <4>[ 4.954676] [] (__tick_broadcast_oneshot_control) from [] (tick_broadcast_oneshot_control+0x3c/0x40) <4>[ 4.965833] r9:ef7cd2f8 r8:00000001 r7:c1b10e94 r6:c1b10ea4 r5:c1b10e44 r4:00000001 <4>[ 4.973867] [] (tick_broadcast_oneshot_control) from [] (cpuidle_enter_state+0x50/0x520) <4>[ 4.983980] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 4.992532] r10:ef7cd2f8 r9:c1b10e44 r8:c1aa22f0 r7:c1b08500 r6:c1b10e44 r5:ef7cd2f8 <4>[ 5.000638] r4:00000001 <4>[ 5.003467] [] (cpuidle_enter) from [] (do_idle+0x20c/0x2f8) <4>[ 5.011146] r7:c1b08500 r6:c1b084bc r5:00000003 r4:ee9da000 <4>[ 5.017097] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 5.024955] r10:00000000 r9:412fc09a r8:1020406a r7:c1cb9650 r6:00000003 r5:ee9da000 <4>[ 5.033062] r4:0000008a <4>[ 5.035891] [] (cpu_startup_entry) from [] (secondary_start_kernel+0x170/0x17c) <4>[ 5.045227] [] (secondary_start_kernel) from [<1030312c>] (0x1030312c) <4>[ 5.052908] r7:c1cb9650 r6:10c0387d r5:00000051 r4:3e9c406a <4>[ 5.058844] irq event stamp: 12518 <4>[ 5.062540] hardirqs last enabled at (12517): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 5.071701] hardirqs last disabled at (12518): [] do_idle+0xb0/0x2f8 <4>[ 5.079212] softirqs last enabled at (12510): [] __do_softirq+0x344/0x520 <4>[ 5.087245] softirqs last disabled at (12499): [] irq_exit+0x170/0x1c8 <4>[ 5.094918] ---[ end trace 96c5c45a3e13713c ]--- <5>[ 5.104062] Loading compiled-in X.509 certificates <6>[ 5.158492] hub 1-1:1.0: USB hub found <6>[ 5.162903] hub 1-1:1.0: 3 ports detected <6>[ 5.189503] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.199662] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.211584] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.219702] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.231879] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.240876] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.248352] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.259184] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.268508] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.276156] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.289897] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 5.302683] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.310676] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.322193] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <4>[ 5.329962] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 5.337781] GPT:7812499 != 31116287 <4>[ 5.341546] GPT:Alternate GPT header not at the end of the disk. <4>[ 5.347920] GPT:7812499 != 31116287 <4>[ 5.351686] GPT: Use GNU Parted to correct GPT errors. <6>[ 5.357187] mmcblk0: p1 p2 p3 <6>[ 5.361173] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.373321] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.382224] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.390138] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.400970] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.410200] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.422193] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.432669] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.442425] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.453893] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.461690] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.473704] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.482591] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.489822] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.500552] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.509794] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.517177] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.527861] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.535511] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.546908] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.554556] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.566635] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.575521] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.582689] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.593377] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.602617] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.610008] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.622815] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 5.630935] hctosys: unable to open rtc device (rtc0) <6>[ 5.640964] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.648676] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.660373] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.668087] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.680173] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.689239] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.696457] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.707218] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.716459] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.723801] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.758808] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 5.775358] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 8.907480] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 8.925622] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.956314] Sending DHCP requests ., OK <6>[ 9.000073] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.36 <6>[ 9.008468] IP-Config: Complete: <6>[ 9.011985] device=eth0, hwaddr=00:19:b8:08:f1:1c, ipaddr=192.168.201.36, mask=255.255.255.0, gw=192.168.201.1 <6>[ 9.022764] host=imx6q-sabrelite-lava-cbg-6, domain=lava-rack, nis-domain=(none) <6>[ 9.030942] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 9.030949] nameserver0=192.168.201.1 <6>[ 9.094876] Freeing unused kernel memory: 2048K <6>[ 9.106106] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 9.451558] udevd[110]: starting version 3.2.9 <5>[ 9.460239] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 9.468227] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 9.475101] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 9.493292] udevd[110]: specified user 'tss' unknown <27>[ 9.499301] udevd[110]: specified group 'tss' unknown <30>[ 9.510834] udevd[111]: starting eudev-3.2.9 <6>[ 10.435719] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 10.447995] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 10.456195] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 10.462474] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 10.476377] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 10.487286] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 10.494998] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 10.507473] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 10.516637] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 10.524449] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 10.531826] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 10.538784] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 10.546122] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 10.557399] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 10.566716] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 10.574095] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 10.584994] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 10.592664] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 10.629377] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 10.662830] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 10.669307] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 10.680852] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 1 <6>[ 10.694778] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 10.703683] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 10.716520] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 10.725647] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 10.733209] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 10.745293] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 10.755207] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 10.763283] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 10.774119] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 10.782493] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 10.790175] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 10.796915] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 10.803672] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 10.808706] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 10.811538] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 10.829013] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 10.830202] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 10.838023] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 10.853233] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 10.864293] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 10.873636] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 10.881174] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 10.952965] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 10.962042] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 10.973827] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 10.984428] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 10.998354] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.007474] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.015341] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 11.026902] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.036455] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.044033] panel-simple panel-lvds0: Dropping the link to regulator.0 done Saving random seed: <5>[ 11.493780] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 11.740847] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9975232/environment . /lava-9975232/environment / # /lava-9975232/bin/lava-test-runner /lava-9975232/0 /lava-9975232/bin/lava-test-runner /lava-9975232/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-9975232/0/tests/0_dmesg + cat uuid + UUID=9975232_1.5.2.4.1<8>[ 12.485569] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 12.591303] <8>[ 12.689095] <8>[ 12.787224] + set +x <8>[ 12.799022] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-9975232/environment / # . /lava-9975232/environment/lava-9975232/bin/lava-test-runner /lava-9975232/1 / # /lava-9975232/bin/lava-test-runner /lava-9975232/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-9975232/1/tests/1_bootrr + cat uuid + UUID=9975232_1.5.2.4.5 <8>[ 13.397675] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9975232/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd panel-lvds0 /lava-9975232/1/../bin/lava-test-case <8>[ 14.562719] /lava-9975232/1/../bin/lava-test-case <8>[ 14.662011] /lava-9975232/1/../bin/lava-test-case <8>[ 14.718366] + set +x <8>[ 14.758327] / #