[Enter `^Ec?' for help]  U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9975238/tftp-deploy-d_cazwv7/kernel/zImage tftp 0x10000000 9975238/tftp-deploy-d_cazwv7/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '9975238/tftp-deploy-d_cazwv7/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 11.1 MiB/s done Bytes transferred = 10424832 (9f1200 hex) => tftp 0x14000000 9975238/tftp-deploy-d_cazwv7/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9975238/tftp-deploy-d_cazwv7/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '9975238/tftp-deploy-d_cazwv7/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 6 MiB/s done Bytes transferred = 11427172 (ae5d64 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9975238/tftp-deploy-d_cazwv7/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9975238/tftp-deploy-d_cazwv7/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '9975238/tftp-deploy-d_cazwv7/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4.4 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9975238/extract-nfsrootfs-g15v0bii,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9975238/extract-nfsrootfs-g15v0bii,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x9f1200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 11427108 Bytes = 10.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.280-cip96 (KernelCI@build-j1346709-arm-gcc-10-multi-v7-defconfig-kselftest-vr5cs) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Fri Apr 14 09:46:15 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s40104 r8192 d21336 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9975238/extract-nfsrootfs-g15v0bii,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 928384K/1048576K available (15360K kernel code, 1762K rwdata, 6312K rodata, 2048K init, 7700K bss, 54656K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (16352 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1763 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7701 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 49054 entries in 192 pages <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000009] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022061] Console: colour dummy device 80x30 <4>[ 0.023948] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.031973] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.036320] ... MAX_LOCK_DEPTH: 48 <4>[ 0.040725] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.045336] ... CLASSHASH_SIZE: 4096 <4>[ 0.049975] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.054646] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.059370] ... CHAINHASH_SIZE: 32768 <4>[ 0.064042] memory used by lock dependency info: 4655 kB <4>[ 0.069723] per task-struct memory footprint: 1536 bytes <6>[ 0.075400] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.085826] pid_max: default: 32768 minimum: 301 <6>[ 0.090974] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.097595] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.106589] CPU: Testing write buffer coherency: ok <6>[ 0.109983] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.116427] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.123449] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.130296] rcu: Hierarchical SRCU implementation. <6>[ 0.137457] EFI services will not be available. <6>[ 0.140347] smp: Bringing up secondary CPUs ... <6>[ 0.146602] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.146614] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.158282] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.158294] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.169196] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.169208] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.178320] smp: Brought up 1 node, 4 CPUs <6>[ 0.182259] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.188770] CPU: All CPU(s) started in SVC mode. <6>[ 0.196400] devtmpfs: initialized <6>[ 0.230845] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.238510] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.246171] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.256498] pinctrl core: initialized pinctrl subsystem <6>[ 0.264048] DMI not present or invalid. <6>[ 0.267280] NET: Registered protocol family 16 <6>[ 0.278362] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.289028] cpuidle: using governor menu <6>[ 0.290851] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.330650] vdd1p1: supplied by regulator-dummy <6>[ 0.334565] vdd3p0: supplied by regulator-dummy <6>[ 0.339216] vdd2p5: supplied by regulator-dummy <6>[ 0.343933] vddarm: supplied by regulator-dummy <6>[ 0.349458] vddpu: supplied by regulator-dummy <6>[ 0.352970] vddsoc: supplied by regulator-dummy <6>[ 0.404876] No ATAGs? <6>[ 0.405359] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.413422] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.430624] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.438636] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.462439] Serial: AMBA PL011 UART driver <6>[ 0.561043] mxs-dma 110000.dma-apbh: initialized <6>[ 0.587078] vgaarb: loaded <5>[ 0.590041] SCSI subsystem initialized <6>[ 0.592609] usbcore: registered new interface driver usbfs <6>[ 0.597220] usbcore: registered new interface driver hub <6>[ 0.602658] usbcore: registered new device driver usb <6>[ 0.612522] i2c i2c-0: IMX I2C adapter registered <6>[ 0.614678] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.622114] i2c i2c-1: IMX I2C adapter registered <6>[ 0.625201] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.632091] i2c i2c-2: IMX I2C adapter registered <6>[ 0.635779] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.645228] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.647667] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.657105] PTP clock support registered <6>[ 0.662000] EDAC MC: Ver: 3.0.0 <6>[ 0.675504] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.941118] NET: Registered protocol family 2 <6>[ 0.943565] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.952211] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 20480 bytes) <6>[ 0.958071] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.965428] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) <6>[ 0.973208] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.979183] UDP hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.984952] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.992066] NET: Registered protocol family 1 <6>[ 0.997909] RPC: Registered named UNIX socket transport module. <6>[ 1.002159] RPC: Registered udp transport module. <6>[ 1.007200] RPC: Registered tcp transport module. <6>[ 1.012069] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.020656] Trying to unpack rootfs image as initramfs... <6>[ 2.218175] Freeing initrd memory: 11160K <4>[ 2.220584] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 2.228004] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 2.242678] Initialise system trusted keyrings <6>[ 2.245646] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.278303] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.284176] NFS: Registering the id_resolver key type <5>[ 2.287117] Key type id_resolver registered <5>[ 2.291322] Key type id_legacy registered <6>[ 2.296214] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.307577] Key type asymmetric registered <5>[ 2.309180] Asymmetric key parser 'x509' registered <6>[ 2.314489] bounce: pool size: 64 pages <6>[ 2.318493] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 2.326086] io scheduler noop registered <6>[ 2.330157] io scheduler deadline registered <6>[ 2.335131] io scheduler cfq registered (default) <6>[ 2.339713] io scheduler mq-deadline registered <6>[ 2.344426] io scheduler kyber registered <4>[ 2.349292] test_firmware: interface ready <6>[ 2.427489] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.432517] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.439945] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.446791] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.498962] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 2.502630] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 2.510352] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 2.516763] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 2.524644] PU : no governor for states <6>[ 2.528336] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <4>[ 2.560020] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 2.567200] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 2.752493] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.768641] SuperH (H)SCI(F) driver initialized <6>[ 2.772767] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 2.782235] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 2.791421] console [ttymxc1] enabled <6>[ 2.791421] console [ttymxc1] enabled <6>[ 2.796519] bootconsole [ec_imx21] disabled <6>[ 2.796519] bootconsole [ec_imx21] disabled <6>[ 2.809353] msm_serial: driver initialized <6>[ 2.814558] STMicroelectronics ASC driver initialized <6>[ 2.825084] STM32 USART driver initialized <6>[ 2.844752] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 2.869278] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.878246] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.885561] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.892580] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.901855] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.909426] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.945164] brd: module loaded <6>[ 2.982709] loop: module loaded <6>[ 2.995884] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.004098] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.012456] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.020970] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 3.032412] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.039764] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.048908] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.061918] scsi host0: ahci-imx <6>[ 3.067306] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 3.111527] CAN device driver interface <6>[ 3.119129] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 3.128094] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 3.137333] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 3.147449] pps pps0: new PPS source ptp0 <6>[ 3.186391] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.195748] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 3.201867] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.208283] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 3.215571] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.238204] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.246051] usbcore: registered new interface driver pegasus <6>[ 3.252155] usbcore: registered new interface driver asix <6>[ 3.257988] usbcore: registered new interface driver ax88179_178a <6>[ 3.264464] usbcore: registered new interface driver cdc_ether <6>[ 3.270790] usbcore: registered new interface driver smsc75xx <6>[ 3.277012] usbcore: registered new interface driver smsc95xx <6>[ 3.283143] usbcore: registered new interface driver net1080 <6>[ 3.289233] usbcore: registered new interface driver cdc_subset <6>[ 3.295828] usbcore: registered new interface driver zaurus <6>[ 3.301885] usbcore: registered new interface driver cdc_ncm <6>[ 3.316344] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.323162] ehci-pci: EHCI PCI platform driver <6>[ 3.328062] ehci-platform: EHCI generic platform driver <6>[ 3.334357] ehci-orion: EHCI orion driver <6>[ 3.339408] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.344358] ehci-st: EHCI STMicroelectronics driver <6>[ 3.350226] ehci-exynos: EHCI EXYNOS driver <6>[ 3.355388] ehci-atmel: EHCI Atmel driver <6>[ 3.360349] tegra-ehci: Tegra EHCI driver <6>[ 3.365385] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.371904] ohci-pci: OHCI PCI platform driver <6>[ 3.376809] ohci-platform: OHCI generic platform driver <6>[ 3.383080] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.388097] ohci-st: OHCI STMicroelectronics driver <6>[ 3.393915] ohci-atmel: OHCI Atmel driver <6>[ 3.400901] usbcore: registered new interface driver usb-storage <6>[ 3.407859] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.413537] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 3.413674] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.426892] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.430479] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 3.446187] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.451547] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.485470] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.495014] hub 1-0:1.0: USB hub found <6>[ 3.499446] hub 1-0:1.0: 1 port detected <6>[ 3.525914] i2c /dev entries driver <6>[ 3.577217] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 3.598749] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.605216] sdhci: Copyright(c) Pierre Ossman <6>[ 3.616167] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.628356] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.636405] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 3.641921] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 3.647796] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 3.691503] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 3.700230] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 3.706164] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 3.745919] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 3.765116] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.773630] usbcore: registered new interface driver usbhid <6>[ 3.779547] usbhid: USB HID core driver <6>[ 3.800930] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.808324] IPv4 over IPsec tunneling driver <6>[ 3.816410] NET: Registered protocol family 10 <6>[ 3.822856] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 3.831742] Segment Routing with IPv6 <6>[ 3.838245] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.844169] mmc0: new high speed SDHC card at address e624 <6>[ 3.848391] NET: Registered protocol family 17 <6>[ 3.854835] mmcblk0: mmc0:e624 SL16G 14.8 GiB <6>[ 3.855461] can: controller area network core (rev 20170425 abi 9) <6>[ 3.866504] NET: Registered protocol family 29 <6>[ 3.871256] can: raw protocol (rev 20170425) <4>[ 3.872658] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 3.875984] can: broadcast manager protocol (rev 20170425 t) <4>[ 3.883691] GPT:29296874 != 31116287 <6>[ 3.889698] can: netlink gateway (rev 20170425) max_hops=1 <4>[ 3.893516] GPT:Alternate GPT header not at the end of the disk. <6>[ 3.900095] 8021q: 802.1Q VLAN Support v1.8 <4>[ 3.905681] GPT:29296874 != 31116287 <5>[ 3.910865] Key type dns_resolver registered <4>[ 3.913949] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.914017] mmcblk0: p1 p2 p3 <4>[ 3.935448] ------------[ cut here ]------------ <6>[ 3.936339] cpu cpu0: Linked as a consumer to regulator.4 <4>[ 3.940357] WARNING: CPU: 0 PID: 0 at include/trace/events/lock.h:13 lock_acquire+0x138/0x1f0 <4>[ 3.940365] Modules linked in: <6>[ 3.946347] cpu cpu0: Linked as a consumer to regulator.5 <4>[ 3.954825] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.280-cip96 #1 <6>[ 3.958488] cpu cpu0: Linked as a consumer to regulator.6 <4>[ 3.963795] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 3.963802] Backtrace: <4>[ 3.965424] ------------[ cut here ]------------ <4>[ 3.965441] WARNING: CPU: 1 PID: 0 at include/trace/events/lock.h:58 lock_release+0x364/0x370 <4>[ 3.965446] Modules linked in: <6>[ 3.975147] ThumbEE CPU extension supported. <4>[ 3.976350] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 3.976361] r7:ffffffff r6:00000000 r5:60000093 r4:c1c9d66c <4>[ 3.976378] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 3.976392] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <4>[ 3.976404] r9:60000093 r8:c1b084bc r7:00000000 r6:00000009 r5:00000000 r4:00000000 <5>[ 3.983224] Registering SWP/SWPB emulation handler <4>[ 3.985909] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 3.985917] r6:c03b8c3c r5:0000000d r4:c16816b0 <4>[ 3.985931] [] (warn_slowpath_null) from [] (lock_acquire+0x138/0x1f0) <4>[ 3.985942] r6:00000000 r5:00000000 r4:c1b05990 <4>[ 4.076351] [] (lock_acquire) from [] (_raw_spin_lock+0x58/0x68) <4>[ 4.084386] r10:ef79a2f8 r9:ef79a2f8 r8:00000001 r7:ef79e740 r6:00000001 r5:c23e9aec <4>[ 4.092494] r4:c1b05980 <4>[ 4.095331] [] (_raw_spin_lock) from [] (__tick_broadcast_oneshot_control+0x4c/0x2ac) <4>[ 4.105174] r4:c1b01e88 <4>[ 4.108004] [] (__tick_broadcast_oneshot_control) from [] (tick_broadcast_oneshot_control+0x3c/0x40) <4>[ 4.119162] r9:ef79a2f8 r8:00000001 r7:c1b10e94 r6:c1b10ea4 r5:c1b10e44 r4:00000001 <4>[ 4.127200] [] (tick_broadcast_oneshot_control) from [] (cpuidle_enter_state+0x50/0x520) <4>[ 4.137316] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 4.145870] r10:ef79a2f8 r9:c1b10e44 r8:c1aa22f0 r7:c1b08500 r6:c1b10e44 r5:ef79a2f8 <4>[ 4.153976] r4:00000001 <4>[ 4.156812] [] (cpuidle_enter) from [] (do_idle+0x20c/0x2f8) <4>[ 4.164494] r7:c1b08500 r6:c1b084bc r5:00000000 r4:c1b00000 <4>[ 4.170447] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 4.178305] r10:c19e4a50 r9:00000001 r8:efffe9c0 r7:c1b08480 r6:00000002 r5:c1b01f78 <4>[ 4.186411] r4:000000cb <4>[ 4.189243] [] (cpu_startup_entry) from [] (rest_init+0x2c8/0x2e0) <4>[ 4.197460] [] (rest_init) from [] (start_kernel+0x46c/0x4a8) <4>[ 4.205225] r6:ffffffff r5:00000001 r4:c1cb9058 <4>[ 4.210129] [] (start_kernel) from [<00000000>] ( (null)) <4>[ 4.216773] r10:10c5387d r9:412fc09a r8:13f00000 r7:00000eb9 r6:10c0387d r5:00000051 <4>[ 4.224879] r4:c19004b0 <4>[ 4.227691] irq event stamp: 7588 <4>[ 4.227705] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.19.280-cip96 #1 <4>[ 4.227719] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 4.231309] hardirqs last enabled at (7587): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 4.231339] hardirqs last disabled at (7588): [] do_idle+0xb0/0x2f8 <4>[ 4.238208] Backtrace: <4>[ 4.245019] softirqs last enabled at (7580): [] __do_softirq+0x344/0x520 <4>[ 4.254074] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 4.261476] softirqs last disabled at (7567): [] irq_exit+0x170/0x1c8 <4>[ 4.264174] r7:ffffffff r6:00000000 r5:60000093 r4:c1c9d66c <4>[ 4.272092] ---[ end trace c218574d320fdb4b ]--- <4>[ 4.279946] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 4.305894] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <4>[ 4.313667] r9:c03ff708 r8:00000001 r7:60000093 r6:00000009 r5:00000000 r4:00000000 <4>[ 4.321701] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 4.330161] r6:c03b8af8 r5:0000003a r4:c16816b0 <4>[ 4.335071] [] (warn_slowpath_null) from [] (lock_release+0x364/0x370) <4>[ 4.343618] r6:c1b456c4 r5:c1b456c4 r4:c1b084bc <4>[ 4.348529] [] (lock_release) from [] (ktime_get+0x84/0x1ac) <4>[ 4.356213] r10:00000001 r9:60000093 r8:00000001 r7:c1b45700 r6:c1b456c4 r5:c03ff708 <4>[ 4.364319] r4:c1b45600 <4>[ 4.367145] [] (ktime_get) from [] (clockevents_program_event+0x6c/0x184) <4>[ 4.375956] r10:ef7ab2f8 r9:c23e9b00 r8:00000001 r7:eb703780 r6:00000000 r5:00000001 <4>[ 4.384063] r4:ee829c40 <4>[ 4.386889] [] (clockevents_program_event) from [] (tick_broadcast_set_event+0x54/0xb4) <4>[ 4.396912] r7:eb703780 r6:00000000 r5:00000001 r4:ee829c40 <4>[ 4.402866] [] (tick_broadcast_set_event) from [] (__tick_broadcast_oneshot_control+0x140/0x2ac) <4>[ 4.413670] r7:ef7af740 r6:ee829c40 r5:00000000 r4:00000001 <4>[ 4.419622] [] (__tick_broadcast_oneshot_control) from [] (tick_broadcast_oneshot_control+0x3c/0x40) <4>[ 4.430777] r9:ef7ab2f8 r8:00000001 r7:c1b10e94 r6:c1b10ea4 r5:c1b10e44 r4:00000001 <4>[ 4.438810] [] (tick_broadcast_oneshot_control) from [] (cpuidle_enter_state+0x50/0x520) <4>[ 4.448924] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 4.457477] r10:ef7ab2f8 r9:c1b10e44 r8:c1aa22f0 r7:c1b08500 r6:c1b10e44 r5:ef7ab2f8 <4>[ 4.465583] r4:00000001 <4>[ 4.468411] [] (cpuidle_enter) from [] (do_idle+0x20c/0x2f8) <4>[ 4.476091] r7:c1b08500 r6:c1b084bc r5:00000001 r4:ee9d6000 <4>[ 4.482042] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 4.489900] r10:00000000 r9:412fc09a r8:1020406a r7:c1cb9650 r6:00000001 r5:ee9d6000 <4>[ 4.498007] r4:0000008a <4>[ 4.500842] [] (cpu_startup_entry) from [] (secondary_start_kernel+0x170/0x17c) <4>[ 4.510181] [] (secondary_start_kernel) from [<1030312c>] (0x1030312c) <4>[ 4.517865] r7:c1cb9650 r6:10c0387d r5:00000051 r4:3e9c406a <4>[ 4.523803] irq event stamp: 17682 <4>[ 4.527499] hardirqs last enabled at (17681): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 4.536659] hardirqs last disabled at (17682): [] do_idle+0xb0/0x2f8 <4>[ 4.544167] softirqs last enabled at (17674): [] __do_softirq+0x344/0x520 <4>[ 4.552201] softirqs last disabled at (17661): [] irq_exit+0x170/0x1c8 <4>[ 4.559874] ---[ end trace c218574d320fdb4c ]--- <5>[ 4.567162] Loading compiled-in X.509 certificates <6>[ 4.618579] hub 1-1:1.0: USB hub found <6>[ 4.622988] hub 1-1:1.0: 3 ports detected <6>[ 4.651275] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.659225] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 4.671136] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 4.678837] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.690927] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 4.699917] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 4.707130] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 4.717885] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 4.727111] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 4.734450] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 4.748066] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 4.760718] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.768388] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 4.779882] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 4.787587] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.799628] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 4.808517] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 4.815736] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 4.826439] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 4.835691] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 4.843030] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 4.853713] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.861362] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 4.872873] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 4.880573] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.892524] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 4.901411] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 4.908622] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 4.919337] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 4.928576] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 4.935950] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 4.948810] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 4.956984] hctosys: unable to open rtc device (rtc0) <6>[ 4.967175] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.974759] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 4.986359] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 4.994010] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.006393] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.015231] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.022463] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.033219] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.042456] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.049845] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.088446] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 5.104932] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 8.257450] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 8.285842] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.315474] Sending DHCP requests ., OK <6>[ 8.359996] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 <6>[ 8.368476] IP-Config: Complete: <6>[ 8.372028] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 <6>[ 8.382807] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) <6>[ 8.390947] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 8.390952] nameserver0=192.168.201.1 <6>[ 8.453197] Freeing unused kernel memory: 2048K <6>[ 8.465903] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 <6>[ 11.361720] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.369692] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 11.376937] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.387332] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 11.388729] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.407564] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 11.407942] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <4>[ 11.419919] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.422720] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.430512] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.444681] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.448383] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 11.451581] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <4>[ 11.463805] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.473858] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.482402] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 11.493090] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.504270] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.516154] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.523860] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 11.555236] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 11.643131] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 11.649701] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <4>[ 11.657472] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.666475] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.667425] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 1 <6>[ 11.677646] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 11.692596] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.701962] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.709133] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 11.715767] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 11.722077] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 11.724228] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 11.732715] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.744039] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.755992] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.762132] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 11.763674] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 11.785592] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.794499] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.809854] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 11.821249] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.830521] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.838106] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 11.861676] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.870201] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.882056] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.889986] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 11.902522] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.911497] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.918765] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 11.929962] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.939244] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.946841] panel-simple panel-lvds0: Dropping the link to regulator.0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f0:fd mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.37 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-7 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 13.892292] systemd[1]: System time before build time, advancing clock. <3>[ 13.969590] cgroup: cgroup2: unknown option "memory_recursiveprot" <30>[ 14.008545] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 14.034068] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 14.082242] systemd[1]: Set hostname to . <30>[ 15.518859] systemd[1]: Queued start job for default target Graphical Interface. <5>[ 15.529446] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 15.540720] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <5>[ 15.575848] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 15.584607] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <5>[ 15.626312] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 15.636709] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 15.677340] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 15.719110] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 15.768335] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 15.817553] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 15.830938] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 15.877063] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 15.917108] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 15.955910] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 15.996632] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 16.039158] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 16.147417] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 16.160858] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 16.198658] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 16.241604] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 16.296344] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 16.340331] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 16.389088] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 16.399694] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 16.419953] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 16.464456] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 16.519230] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <5>[ 16.576570] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 16.594181] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <5>[ 16.636720] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 16.652805] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <5>[ 16.686621] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 16.710696] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 16.752075] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 16.777995] systemd[1]: Starting Journal Service... Starting Journal Service... <6>[ 16.807664] fuse init (API version 7.27) <30>[ 16.830269] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 16.875123] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 16.922909] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 16.978278] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 17.029797] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 17.084226] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 17.162803] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 17.172262] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 17.230835] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 17.240318] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. <30>[ 17.291438] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 17.300556] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. <30>[ 17.350622] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. <30>[ 17.391537] systemd[1]: Finished Remount Root and Kernel File Systems. [ OK ] Finished Remount Root and Kernel File Systems. <30>[ 17.446016] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... <30>[ 17.493867] systemd[1]: Mounting Kernel Configuration File System... Mounting Kernel Configuration File System... <30>[ 17.542710] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. <30>[ 17.554632] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. <30>[ 17.571922] systemd[1]: Starting Load/Save Random Seed... Starting Load/Save Random Seed... <5>[ 17.615997] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 17.629900] systemd[1]: Starting Apply Kernel Variables... <5>[ 17.635775] random: systemd-journal: uninitialized urandom read (16 bytes read) Starting Apply Kernel Variables... <5>[ 17.654956] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 17.668952] systemd[1]: Starting Create System Users... Starting Create System Users... <30>[ 17.711381] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. Starting Flush Journal to Persistent Storage... [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... <46>[ 17.991059] systemd-journald[167]: Received client request to flush runtime journal. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Rule-based Manage…for Device Events and Files... <5>[ 19.006308] random: crng init done <5>[ 19.010133] random: 46 urandom warning(s) missed due to ratelimiting [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Started Network Service. [ OK ] Finished Create Volatile Files and Directories. Starting Network Name Resolution... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Found device /dev/ttymxc1. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.280-cip96 #1 SMP Fri Apr 14 09:46:15 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9975238/extract-nfsrootfs-g15v0bii' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9975238/extract-nfsr<6>[ 35.063145] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 35.071258] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 35.090455] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 35.098682] pwm-backlight backlight-lvds: Dropping the link to regulator.8 o<4>[ 35.119046] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 35.128359] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 35.136113] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 35.153261] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 35.162967] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 35.170902] panel-simple panel-lvds0: Dropping the link to regulator.0 o<6>[ 35.182100] platform backlight-lcd: deferred probe pending <6>[ 35.188454] platform backlight-lvds: deferred probe pending <6>[ 35.194352] platform panel-lcd: deferred probe pending <6>[ 35.199960] platform panel-lvds0: deferred probe pending tfs-g15v0bii' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-9975238/environment . /lava-9975238/environment / # /lava-9975238/bin/lava-test-runner /lava-9975238/0 /lava-9975238/bin/lava-test-runner /lava-9975238/0 <6>[ 38.907099] usb_otg_vbus: disabling <6>[ 38.911085] CAN XCVR: disabling + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-9975238/0/tests/0_timesync-off ++ cat uuid + UUID=9975238_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-lib + TESTRUN_ID=1_kselftest-lib + cd /lava-9975238/0/tests/1_kselftest-lib ++ cat uuid + UUID=9975238_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c lib -T '' -t kselftest_armhf.tar.gz -s True -u None -L '' -S /dev/null -b imx6q-sabrelite -g cip -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-04-14 09:53:57-- http://none/ Resolving none (none)... failed: Name or service not known. wget: unable to resolve host address 'none' tar: None: Cannot open: No such file or directory tar: Error is not recoverable: exiting now ./kselftest.sh: 160: cd: can't cd to kselftest / #