[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.13 (9 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10389399/tftp-deploy-c_cq_q5k/kernel/zImage tftp 0x10000000 10389399/tftp-deploy-c_cq_q5k/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.13 Filename '10389399/tftp-deploy-c_cq_q5k/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 4.4 MiB/s done Bytes transferred = 8729088 (853200 hex) => tftp 0x14000000 10389399/tftp-deploy-c_cq_q5k/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10389399/tftp-deploy-c_cq_q5k/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.13 Filename '10389399/tftp-deploy-c_cq_q5k/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 4.9 MiB/s done Bytes transferred = 13333818 (cb753a hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10389399/tftp-deploy-c_cq_q5k/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10389399/tftp-deploy-c_cq_q5k/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.13 Filename '10389399/tftp-deploy-c_cq_q5k/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.6 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x853200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13333754 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.283-cip98 (KernelCI@build-j1532596-arm-gcc-10-multi-v7-defconfig-9qs76) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Fri May 19 13:46:04 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939140K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 43900K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000006] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008096] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.021041] Console: colour dummy device 80x30 <6>[ 0.022925] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.033606] pid_max: default: 32768 minimum: 301 <6>[ 0.038594] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.045347] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.053180] CPU: Testing write buffer coherency: ok <6>[ 0.057792] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.063444] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069699] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077398] rcu: Hierarchical SRCU implementation. <6>[ 0.083966] EFI services will not be available. <6>[ 0.086215] smp: Bringing up secondary CPUs ... <6>[ 0.091477] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091483] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.102820] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.102826] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114007] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114013] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124473] smp: Brought up 1 node, 4 CPUs <6>[ 0.128728] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.135231] CPU: All CPU(s) started in SVC mode. <6>[ 0.141166] devtmpfs: initialized <6>[ 0.150949] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156404] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.166150] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175683] pinctrl core: initialized pinctrl subsystem <6>[ 0.179985] DMI not present or invalid. <6>[ 0.183205] NET: Registered protocol family 16 <6>[ 0.190543] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197203] cpuidle: using governor menu <6>[ 0.199179] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.214021] vdd1p1: supplied by regulator-dummy <6>[ 0.216490] vdd3p0: supplied by regulator-dummy <6>[ 0.221218] vdd2p5: supplied by regulator-dummy <6>[ 0.226052] vddarm: supplied by regulator-dummy <6>[ 0.230959] vddpu: supplied by regulator-dummy <6>[ 0.235381] vddsoc: supplied by regulator-dummy <6>[ 0.253836] No ATAGs? <6>[ 0.253986] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.261945] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.271388] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278270] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290081] Serial: AMBA PL011 UART driver <6>[ 0.293903] console [pstore-1] enabled <6>[ 0.295759] pstore: Registered ramoops as persistent store backend <6>[ 0.302049] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.330113] mxs-dma 110000.dma-apbh: initialized <6>[ 0.339568] vgaarb: loaded <5>[ 0.340492] SCSI subsystem initialized <6>[ 0.344089] usbcore: registered new interface driver usbfs <6>[ 0.349504] usbcore: registered new interface driver hub <6>[ 0.355036] usbcore: registered new device driver usb <6>[ 0.361594] i2c i2c-0: IMX I2C adapter registered <6>[ 0.365267] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.371402] i2c i2c-1: IMX I2C adapter registered <6>[ 0.375791] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.381777] i2c i2c-2: IMX I2C adapter registered <6>[ 0.386339] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.393424] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.397117] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.406525] PTP clock support registered <6>[ 0.410917] EDAC MC: Ver: 3.0.0 <6>[ 0.416852] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.480017] NET: Registered protocol family 2 <6>[ 0.482240] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.489768] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.496693] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.504085] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.510829] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.517507] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.523495] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.530261] NET: Registered protocol family 1 <6>[ 0.535240] RPC: Registered named UNIX socket transport module. <6>[ 0.540890] RPC: Registered udp transport module. <6>[ 0.545817] RPC: Registered tcp transport module. <6>[ 0.550794] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.557989] Trying to unpack rootfs image as initramfs... <6>[ 1.671168] Freeing initrd memory: 13024K <4>[ 1.673094] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.680347] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.690295] Initialise system trusted keyrings <6>[ 1.693301] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.705644] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.709537] NFS: Registering the id_resolver key type <5>[ 1.714239] Key type id_resolver registered <5>[ 1.718662] Key type id_legacy registered <6>[ 1.722936] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.729878] Key type asymmetric registered <5>[ 1.731860] Asymmetric key parser 'x509' registered <6>[ 1.737057] bounce: pool size: 64 pages <6>[ 1.741115] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.748754] io scheduler noop registered <6>[ 1.752912] io scheduler deadline registered <6>[ 1.757581] io scheduler cfq registered (default) <6>[ 1.762395] io scheduler mq-deadline registered <6>[ 1.767195] io scheduler kyber registered <6>[ 1.792966] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.797516] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.804633] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.811930] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.831975] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.835366] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.843221] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.849422] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.857283] PU : no governor for states <4>[ 1.857344] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 1.861246] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.871008] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.934666] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.941965] SuperH (H)SCI(F) driver initialized <6>[ 1.944814] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.953571] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.964543] console [ttymxc1] enabled <6>[ 1.964543] console [ttymxc1] enabled <6>[ 1.969542] bootconsole [ec_imx21] disabled <6>[ 1.969542] bootconsole [ec_imx21] disabled <6>[ 1.979612] msm_serial: driver initialized <6>[ 1.985839] STMicroelectronics ASC driver initialized <6>[ 1.993000] STM32 USART driver initialized <4>[ 2.008094] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.016772] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.023756] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.030535] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.039562] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.046681] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.061236] brd: module loaded <6>[ 2.073968] loop: module loaded <6>[ 2.080619] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.088845] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.097136] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.105585] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.116379] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.123661] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.132737] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.143529] scsi host0: ahci-imx <6>[ 2.147605] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.166502] CAN device driver interface <6>[ 2.171896] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.178991] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.187974] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.197082] pps pps0: new PPS source ptp0 <6>[ 2.227751] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.235155] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.241286] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.247539] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.254768] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.266495] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.274219] usbcore: registered new interface driver pegasus <6>[ 2.280200] usbcore: registered new interface driver asix <6>[ 2.285899] usbcore: registered new interface driver ax88179_178a <6>[ 2.292313] usbcore: registered new interface driver cdc_ether <6>[ 2.298475] usbcore: registered new interface driver smsc75xx <6>[ 2.304537] usbcore: registered new interface driver smsc95xx <6>[ 2.310599] usbcore: registered new interface driver net1080 <6>[ 2.316554] usbcore: registered new interface driver cdc_subset <6>[ 2.322785] usbcore: registered new interface driver zaurus <6>[ 2.328713] usbcore: registered new interface driver cdc_ncm <6>[ 2.337585] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.344382] ehci-pci: EHCI PCI platform driver <6>[ 2.349156] ehci-platform: EHCI generic platform driver <6>[ 2.354939] ehci-orion: EHCI orion driver <6>[ 2.359455] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.363920] ehci-st: EHCI STMicroelectronics driver <6>[ 2.369276] ehci-exynos: EHCI EXYNOS driver <6>[ 2.373906] ehci-atmel: EHCI Atmel driver <6>[ 2.378386] tegra-ehci: Tegra EHCI driver <6>[ 2.382877] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.389358] ohci-pci: OHCI PCI platform driver <6>[ 2.394113] ohci-platform: OHCI generic platform driver <6>[ 2.399880] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.404345] ohci-st: OHCI STMicroelectronics driver <6>[ 2.409692] ohci-atmel: OHCI Atmel driver <6>[ 2.414964] usbcore: registered new interface driver usb-storage <6>[ 2.423509] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.435546] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.445710] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.450900] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.486882] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.488365] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.493197] hub 1-0:1.0: USB hub found <6>[ 2.498267] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.502286] hub 1-0:1.0: 1 port detected <6>[ 2.508794] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.519190] i2c /dev entries driver <3>[ 2.535340] imx_thermal tempmon: invalid sensor calibration data <3>[ 2.541650] imx_thermal tempmon: failed to init from from fsl,tempmon-data <4>[ 2.548821] imx_thermal: probe of tempmon failed with error -22 <6>[ 2.558276] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.569701] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.576150] sdhci: Copyright(c) Pierre Ossman <6>[ 2.583060] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.591329] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.598133] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.603566] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.609108] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.648947] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.656983] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.662488] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.702344] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.713765] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.720824] usbcore: registered new interface driver usbhid <6>[ 2.726664] usbhid: USB HID core driver <6>[ 2.736731] NET: Registered protocol family 10 <6>[ 2.742577] Segment Routing with IPv6 <6>[ 2.746602] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.753363] NET: Registered protocol family 17 <6>[ 2.758116] can: controller area network core (rev 20170425 abi 9) <6>[ 2.764629] NET: Registered protocol family 29 <6>[ 2.769365] can: raw protocol (rev 20170425) <6>[ 2.773905] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.779859] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.786021] Key type dns_resolver registered <6>[ 2.791355] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.797114] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.802829] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.809295] ThumbEE CPU extension supported. <5>[ 2.813842] Registering SWP/SWPB emulation handler <5>[ 2.819701] Loading compiled-in X.509 certificates <6>[ 2.826366] pstore: Using compression: deflate <6>[ 2.850160] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.857597] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.866297] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.874848] mmc0: new high speed SDHC card at address 0001 <6>[ 2.880866] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.889830] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.898535] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.906932] mmcblk0: mmc0:0001 SD 14.8 GiB <6>[ 2.911651] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.918851] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.927272] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.936296] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.943589] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.951890] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.959431] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.967973] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.975565] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.984435] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.993128] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.000313] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.008413] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.017447] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.024814] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.033760] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.040781] hctosys: unable to open rtc device (rtc0) <6>[ 3.047709] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.055108] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.063765] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.071463] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.080405] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.089109] panel-simple panel-lcd: Linked as a consumer to regulator.0 <4>[ 3.096206] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.103908] GPT:7812499 != 30965759 <4>[ 3.107705] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.113978] GPT:7812499 != 30965759 <4>[ 3.117746] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.123196] mmcblk0: p1 p2 p3 <6>[ 3.126743] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.134898] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.143947] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.151255] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.157413] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 3.172890] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 3.179346] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.189225] hub 1-1:1.0: USB hub found <6>[ 3.193303] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.201854] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.209332] hub 1-1:1.0: 3 ports detected <6>[ 3.213697] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.222530] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.231231] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.238298] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.246324] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.255368] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.262554] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.271191] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.278577] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.286968] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.294460] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.303230] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.311935] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.318896] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.326890] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.335902] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.343041] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.277755] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 5.306992] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.337056] Sending DHCP requests ., OK <6>[ 5.381077] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.13 <6>[ 5.389420] IP-Config: Complete: <6>[ 5.392936] device=eth0, hwaddr=00:19:b8:00:e5:47, ipaddr=192.168.201.13, mask=255.255.255.0, gw=192.168.201.1 <6>[ 5.403679] host=imx6q-sabrelite-lava-cbg-2, domain=lava-rack, nis-domain=(none) <6>[ 5.411821] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 5.411831] nameserver0=192.168.201.1 <6>[ 5.430706] Freeing unused kernel memory: 2048K <6>[ 5.457546] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 5.602746] udevd[107]: starting version 3.2.9 <5>[ 5.608557] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.615564] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.622432] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 5.637880] udevd[107]: specified user 'tss' unknown <27>[ 5.643335] udevd[107]: specified group 'tss' unknown <30>[ 5.651214] udevd[108]: starting eudev-3.2.9 <6>[ 6.132356] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.150273] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.157669] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 6.162086] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.165444] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 6.173519] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.191585] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.198737] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.205553] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 6.216601] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.226069] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.234806] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.241816] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.250368] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.259457] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.266604] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.274850] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.282307] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.291627] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.299144] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.312485] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.321288] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.334933] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.343824] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.352952] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.360379] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.369242] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.376592] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 6.383089] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 6.389438] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.394679] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 6.398392] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.409199] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 6.420668] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 6.426600] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 6.454786] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 6.461216] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 6.468458] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <4>[ 6.475984] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.484750] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.492033] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.501212] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.510338] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.517958] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.526500] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.534135] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.543282] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.551235] pwm-backlight backlight-lvds: Dropping the link to regulator.8 done Saving random seed: <5>[ 6.793879] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 6.902834] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10389399/environment . /lava-10389399/environment / # /lava-10389399/bin/lava-test-runner /lava-10389399/0 /lava-10389399/bin/lava-test-runner /lava-10389399/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-10389399/0/tests/0_dmesg + cat uuid + <8>[ 7.537419] UUID=10389399_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 7.581233] <8>[ 7.621569] <8>[ 7.662030] + set +x <8>[ 7.671940] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-10389399/environment / # . /lava-10389399/environment/lava-10389399/bin/lava-test-runner /lava-10389399/1 / # /lava-10389399/bin/lava-test-runner /lava-10389399/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-10389399/1/tests/1_bootrr + cat uuid + UUID=1038939<8>[ 8.207890] 9_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10389399/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lcd panel-lvds0 backlight-lcd backlight-lvds /lava-10389399/1/../bin/lava-test-case <8>[ 9.291632] /lava-10389399/1/../bin/lava-test-case <8>[ 9.341185] /lava-10389399/1/../bin/lava-test-case <8>[ 9.374491] + set +x <8>[ 9.393286] / #