Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.9 (3 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 958225/tftp-deploy-sxwm7562/kernel/zImage tftp 0x82000000 958225/tftp-deploy-sxwm7562/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '958225/tftp-deploy-sxwm7562/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 5.1 MiB/s done Bytes transferred = 10334720 (9db200 hex) => tftp 0x83000000 958225/tftp-deploy-sxwm7562/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 958225/tftp-deploy-sxwm7562/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '958225/tftp-deploy-sxwm7562/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################ 5.1 MiB/s done Bytes transferred = 15495940 (ec7304 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 958225/tftp-deploy-sxwm7562/dtb/am335x-boneblack.dtb tftp 0x88000000 958225/tftp-deploy-sxwm7562/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '958225/tftp-deploy-sxwm7562/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *### 4.2 MiB/s done Bytes transferred = 34893 (884d hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-06-09 16:14:52 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15495876 Bytes = 14.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8800b84c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.284-cip99 (KernelCI@build-j15434-arm-gcc-10-multi-v7-defconfig-kselftest-dp2f9) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Fri Jun 9 15:02:50 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omapserial0 at MMIO 0x44e09000 (options '') [ 0.000000] bootconsole [omapserial0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 17 pages/cpu s40104 r8192 d21336 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129540 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) <6>[ 0.000000] Memory: 403680K/522240K available (14336K kernel code, 1759K rwdata, 6288K rodata, 2048K init, 7699K bss, 53024K reserved, 65536K cma-reserved, 0K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xdfe00000 ( 510 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (15328 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1760 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7700 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] ftrace: allocating 48530 entries in 190 pages <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz <6>[ 0.000020] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008260] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.017996] OMAP clocksource: timer1 at 24000000 Hz <2>[ 0.027397] timer_probe: no matching timers found <6>[ 0.033101] Console: colour dummy device 80x30 <4>[ 0.037900] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.046136] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.050573] ... MAX_LOCK_DEPTH: 48 <4>[ 0.055083] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.059843] ... CLASSHASH_SIZE: 4096 <4>[ 0.064541] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.069390] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.074178] ... CHAINHASH_SIZE: 32768 <4>[ 0.079033] memory used by lock dependency info: 4655 kB <4>[ 0.084797] per task-struct memory footprint: 1536 bytes <6>[ 0.090697] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.185149] pid_max: default: 32768 minimum: 301 <6>[ 0.190533] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.197537] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.206954] CPU: Testing write buffer coherency: ok <6>[ 0.212368] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.218949] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.226671] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.235791] rcu: Hierarchical SRCU implementation. <6>[ 0.244974] EFI services will not be available. <6>[ 0.250537] smp: Bringing up secondary CPUs ... <6>[ 0.255389] smp: Brought up 1 node, 1 CPU <6>[ 0.259833] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.266458] CPU: All CPU(s) started in SVC mode. <6>[ 0.274578] devtmpfs: initialized <6>[ 0.308856] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.318015] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.328518] futex hash table entries: 256 (order: 2, 16384 bytes) <6>[ 0.339945] pinctrl core: initialized pinctrl subsystem <6>[ 0.351050] DMI not present or invalid. <6>[ 0.357095] NET: Registered protocol family 16 <6>[ 0.370554] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.479338] l4_wkup_cm:clk:0010:0: failed to disable <6>[ 0.532011] cpuidle: using governor menu <6>[ 0.561977] OMAP GPIO hardware version 0.1 <6>[ 0.608004] No ATAGs? <6>[ 0.608022] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 0.635603] Serial: AMBA PL011 UART driver <6>[ 0.708192] edma 49000000.edma: TI EDMA DMA engine driver <6>[ 0.724356] vgaarb: loaded <5>[ 0.730098] SCSI subsystem initialized <6>[ 0.735931] usbcore: registered new interface driver usbfs <6>[ 0.742144] usbcore: registered new interface driver hub <6>[ 0.747930] usbcore: registered new device driver usb <6>[ 0.758024] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.763450] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.773141] PTP clock support registered <6>[ 0.777944] EDAC MC: Ver: 3.0.0 <6>[ 0.792300] clocksource: Switched to clocksource timer1 <6>[ 1.052660] NET: Registered protocol family 2 <6>[ 1.057880] IP idents hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 1.066539] tcp_listen_portaddr_hash hash table entries: 256 (order: 1, 10240 bytes) <6>[ 1.074905] TCP established hash table entries: 4096 (order: 2, 16384 bytes) <6>[ 1.082483] TCP bind hash table entries: 4096 (order: 5, 147456 bytes) <6>[ 1.090060] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 1.097201] UDP hash table entries: 256 (order: 2, 20480 bytes) <6>[ 1.103679] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) <6>[ 1.110912] NET: Registered protocol family 1 <6>[ 1.118434] RPC: Registered named UNIX socket transport module. <6>[ 1.124938] RPC: Registered udp transport module. <6>[ 1.129968] RPC: Registered tcp transport module. <6>[ 1.135146] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.144051] Trying to unpack rootfs image as initramfs... <6>[ 2.664080] Freeing initrd memory: 15136K <6>[ 2.670387] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 2.686170] Initialise system trusted keyrings <6>[ 2.692259] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 2.727061] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.736544] NFS: Registering the id_resolver key type <5>[ 2.742075] Key type id_resolver registered <5>[ 2.746744] Key type id_legacy registered <6>[ 2.751305] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.764525] Key type asymmetric registered <5>[ 2.769090] Asymmetric key parser 'x509' registered <6>[ 2.774692] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 2.782666] io scheduler noop registered <6>[ 2.786900] io scheduler deadline registered <6>[ 2.792067] io scheduler cfq registered (default) <6>[ 2.797202] io scheduler mq-deadline registered <6>[ 2.802049] io scheduler kyber registered <4>[ 2.807283] test_firmware: interface ready <6>[ 2.832625] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 3.075453] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.093365] SuperH (H)SCI(F) driver initialized <6>[ 3.100897] msm_serial: driver initialized <6>[ 3.106325] omap_uart 44e09000.serial: no wakeirq for uart0 <6>[ 3.112780] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 30, base_baud = 3000000) is a OMAP UART0 <6>[ 3.123003] console [ttyO0] enabled <6>[ 3.123003] console [ttyO0] enabled <6>[ 3.130721] bootconsole [omapserial0] disabled <6>[ 3.130721] bootconsole [omapserial0] disabled <6>[ 3.143032] STMicroelectronics ASC driver initialized <6>[ 3.153043] STM32 USART driver initialized <6>[ 3.162383] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 3.177784] random: crng init done <6>[ 3.184224] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <6>[ 3.233802] brd: module loaded <6>[ 3.266718] loop: module loaded <6>[ 3.303502] CAN device driver interface <6>[ 3.310265] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.319550] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 3.326048] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.332768] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 3.340335] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.432341] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 3.440706] davinci_mdio 4a101000.mdio: detected phy mask fffffffe <6>[ 3.481724] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 3.497241] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 3.505583] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 3.512779] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 3.523693] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.531917] usbcore: registered new interface driver pegasus <6>[ 3.538485] usbcore: registered new interface driver asix <6>[ 3.544615] usbcore: registered new interface driver ax88179_178a <6>[ 3.551375] usbcore: registered new interface driver cdc_ether <6>[ 3.558455] usbcore: registered new interface driver smsc75xx <6>[ 3.565042] usbcore: registered new interface driver smsc95xx <6>[ 3.571442] usbcore: registered new interface driver net1080 <6>[ 3.577832] usbcore: registered new interface driver cdc_subset <6>[ 3.584475] usbcore: registered new interface driver zaurus <6>[ 3.590760] usbcore: registered new interface driver cdc_ncm <6>[ 3.603360] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.610500] ehci-pci: EHCI PCI platform driver <6>[ 3.615708] ehci-platform: EHCI generic platform driver <6>[ 3.622059] ehci-orion: EHCI orion driver <6>[ 3.627166] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.632229] ehci-st: EHCI STMicroelectronics driver <6>[ 3.638110] ehci-exynos: EHCI EXYNOS driver <6>[ 3.643365] ehci-atmel: EHCI Atmel driver <6>[ 3.648317] tegra-ehci: Tegra EHCI driver <6>[ 3.653392] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.660242] ohci-pci: OHCI PCI platform driver <6>[ 3.665428] ohci-platform: OHCI generic platform driver <6>[ 3.671753] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.676853] ohci-st: OHCI STMicroelectronics driver <6>[ 3.682823] ohci-atmel: OHCI Atmel driver <6>[ 3.689308] usbcore: registered new interface driver usb-storage <6>[ 3.713571] i2c /dev entries driver <6>[ 3.757301] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.764225] sdhci: Copyright(c) Pierre Ossman <6>[ 3.772652] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 3.782060] omap_hsmmc 48060000.mmc: Got CD GPIO <6>[ 3.789012] omap_hsmmc 48060000.mmc: Linked as a consumer to regulator.1 <6>[ 3.826683] omap_hsmmc 481d8000.mmc: Linked as a consumer to regulator.1 <6>[ 3.861249] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.872283] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.889841] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.900537] usbcore: registered new interface driver usbhid <6>[ 3.906834] usbhid: USB HID core driver <6>[ 3.926014] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.934021] IPv4 over IPsec tunneling driver <6>[ 3.942741] NET: Registered protocol family 10 <6>[ 3.952452] Segment Routing with IPv6 <6>[ 3.958972] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.969686] NET: Registered protocol family 17 <6>[ 3.974883] can: controller area network core (rev 20170425 abi 9) <6>[ 3.981903] NET: Registered protocol family 29 <6>[ 3.986953] can: raw protocol (rev 20170425) <6>[ 3.991848] can: broadcast manager protocol (rev 20170425 t) <6>[ 3.998178] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 4.005809] Key type dns_resolver registered <6>[ 4.016409] ThumbEE CPU extension supported. <5>[ 4.021212] Registering SWP/SWPB emulation handler <3>[ 4.026630] omap_voltage_late_init: Voltage driver support not added <5>[ 4.040114] Loading compiled-in X.509 certificates <6>[ 4.153064] mmc1: new high speed MMC card at address 0001 <6>[ 4.163764] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.170226] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 4.178136] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 4.186565] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (235:0) <6>[ 4.203417] mmcblk1: p1 <6>[ 4.246325] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.255355] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 4.264233] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.394642] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.404245] hctosys: unable to open rtc device (rtc0) <6>[ 4.428421] net eth0: initializing cpsw version 1.12 (0) <6>[ 4.533645] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 4.555038] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 7.713395] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 7.732381] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.762257] Sending DHCP requests ., OK <6>[ 7.806616] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.9 <6>[ 7.815113] IP-Config: Complete: <6>[ 7.818782] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.9, mask=255.255.255.0, gw=192.168.11.1 <6>[ 7.829821] host=192.168.11.9, domain=usen.ad.jp, nis-domain=(none) <6>[ 7.837176] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 7.837183] nameserver0=192.168.11.1 <6>[ 7.894142] Freeing unused kernel memory: 2048K <6>[ 7.900562] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.410733] udevd[84]: starting version 3.2.9 <27>[ 8.436664] udevd[84]: specified user 'tss' unknown <27>[ 8.443258] udevd[84]: specified group 'tss' unknown <30>[ 8.460424] udevd[85]: starting eudev-3.2.9 <4>[ 12.764303] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator <6>[ 12.775410] am335x-phy-driver 47401300.usb-phy: Linked as a consumer to regulator.0 <4>[ 13.056540] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator <6>[ 13.067798] am335x-phy-driver 47401b00.usb-phy: Linked as a consumer to regulator.0 <6>[ 13.251868] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 13.258850] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 13.394077] hub 1-0:1.0: USB hub found <6>[ 13.425024] hub 1-0:1.0: 1 port detected done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-958225/environment . /lava-958225/environment / # /lava-958225/bin/lava-test-runner /lava-958225/0 /lava-958225/bin/lava-test-runner /lava-958225/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-958225/0/tests/0_dmesg + cat uuid + UUID=958225_1.5.2.4.1 + set +x <8>[ 16.891153] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh kern :crit : timer_probe: no matching timers found <8>[ 17.020209] <8>[ 17.134578] <8>[ 17.248680] + set +x <8>[ 17.263353] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-958225/environment / # . /lava-958225/environment/lava-958225/bin/lava-test-runner /lava-958225/1 / # /lava-958225/bin/lava-test-runner /lava-958225/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-958225/1/tests/1_bootrr + cat uuid + UUID=958225_1.5.2.4.5 + set +x <8>[ 17.879358] + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-958225/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto sound /lava-958225/1/../bin/lava-test-case <8>[ 19.053421] /lava-958225/1/../bin/lava-test-case <8>[ 19.165352] /lava-958225/1/../bin/lava-test-case <8>[ 19.226024] /lava-958225/1/../bin/lava-test-case <8>[ 20.367897] /lava-958225/1/../bin/lava-test-case <8>[ 21.465941] /lava-958225/1/../bin/lava-test-case <8>[ 21.548450] /lava-958225/1/../bin/lava-test-case <8>[ 21.655609] /lava-958225/1/../bin/lava-test-case <8>[ 21.761289] /lava-958225/1/../bin/lava-test-case <8>[ 21.843898] /lava-958225/1/../bin/lava-test-case <8>[ 21.948619] /lava-958225/1/../bin/lava-test-case <8>[ 23.046149] /lava-958225/1/../bin/lava-test-case <8>[ 24.143442] /lava-958225/1/../bin/lava-test-case <8>[ 24.204070] /lava-958225/1/../bin/lava-test-case <8>[ 24.264458] /lava-958225/1/../bin/lava-test-case <8>[ 24.347481] /lava-958225/1/../bin/lava-test-case <8>[ 24.453860] /lava-958225/1/../bin/lava-test-case <8>[ 24.536775] /lava-958225/1/../bin/lava-test-case <8>[ 25.658201] /lava-958225/1/../bin/lava-test-case <8>[ 26.778947] /lava-958225/1/../bin/lava-test-case <8>[ 26.861321] /lava-958225/1/../bin/lava-test-case <8>[ 26.968377] /lava-958225/1/../bin/lava-test-case <8>[ 27.078481] /lava-958225/1/../bin/lava-test-case <8>[ 27.161528] /lava-958225/1/../bin/lava-test-case <8>[ 27.269465] /lava-958225/1/../bin/lava-test-case <8>[ 27.351886] /lava-958225/1/../bin/lava-test-case <8>[ 27.459268] /lava-958225/1/../bin/lava-test-case <8>[ 28.556153] /lava-958225/1/../bin/lava-test-case <8>[ 29.655713] /lava-958225/1/../bin/lava-test-case <8>[ 30.753595] /lava-958225/1/../bin/lava-test-case <8>[ 31.851486] /lava-958225/1/../bin/lava-test-case <8>[ 31.935808] /lava-958225/1/../bin/lava-test-case <8>[ 32.041349] /lava-958225/1/../bin/lava-test-case <8>[ 33.138885] /lava-958225/1/../bin/lava-test-case <8>[ 34.238120] /lava-958225/1/../bin/lava-test-case <8>[ 34.321109] /lava-958225/1/../bin/lava-test-case <8>[ 34.429312] <6>[ 34.449812] platform sound: deferred probe pending /lava-958225/1/../bin/lava-test-case <8>[ 35.540242] /lava-958225/1/../bin/lava-test-case <8>[ 36.638129] /lava-958225/1/../bin/lava-test-case <8>[ 37.735123] /lava-958225/1/../bin/lava-test-case <8>[ 38.833596] /lava-958225/1/../bin/lava-test-case <8>[ 39.929022] /lava-958225/1/../bin/lava-test-case <8>[ 41.028051] /lava-958225/1/../bin/lava-test-case <8>[ 42.126403] /lava-958225/1/../bin/lava-test-case <8>[ 43.223662] /lava-958225/1/../bin/lava-test-case <8>[ 44.320162] /lava-958225/1/../bin/lava-test-case <8>[ 45.418151] /lava-958225/1/../bin/lava-test-case <8>[ 46.515008] /lava-958225/1/../bin/lava-test-case <8>[ 47.611877] /lava-958225/1/../bin/lava-test-case <8>[ 48.708685] /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: line 84: assert_device-present: not found /lava-958225/1/../bin/lava-test-case <8>[ 48.795862] /lava-958225/1/../bin/lava-test-case <8>[ 49.916555] /lava-958225/1/../bin/lava-test-case <8>[ 51.008248] + set +x <8>[ 51.035000] / #