connecting to NetworkSerialPort(target=Target(name='imx53-qsrb-0', env=None), name='NetworkSerialPort', state=, avail=True, host='moxa.cuskci.stw.pengutronix.de', port=4010, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t moxa.cuskci.stw.pengutronix.de:4010 connected to 10.8.254.5 (port 4010) Escape character: Ctrl-\ Type the escape character to get to the prompt. barebox 2023.01.0 #1 Fri Jan 27 16:21:21 CET 2023 Board: Freescale i.MX53 Quick Start-R Board detected i.MX53 revision 2.1 mc13xxx-i2c mc347080: Found MC34708 ID: 0x014 mdio_bus: miibus0: probed eth0: got preset MAC address: 00:04:9f:02:71:b3 imx-usb 53f80200.usb@53f80200.of: USB EHCI 1.00 imx-esdhc 50004000.mmc@50004000.of: registered as mmc0 imx-esdhc 50020000.mmc@50020000.of: registered as mmc2 imx-ipuv3 18000000.ipu@18000000.of: IPUv3M probed netconsole: registered as netconsole-1 malloc space: 0xbfe7d3c0 -> 0xcfcfa77f (size 254.5 MiB) mmc0: detected SD card version 2.0 mmc0: registered mmc0 MCIMX53-START-R board 1.0 rev B envfs: no envfs (magic mismatch) - envfs never written? [?25h Hit m for menu or any to stop autoboot: 3 [1;32mbarebox@[1;36mFreescale i.MX53 Quick Start-R Board:/[0m bootm -v -r /mnt/tftp/972620/tftp-deploy-kkxy6haf/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/972620/tftp-deploy-kkxy6haf/dtb/imx53-qsrb.dtb /mnt/tftp/972620/tftp-deploy-kkxy6haf/kernel/zImage [1;32mbarebox@[1;36mFreescale i.MX53 Quick Start-R Board:/[0m bootm -v -r /mnt/tftp/972620/tftp-deploy-kkxy6haf/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/972620/tftp-deploy-kkxy6haf/dtb/imx53-qsrb.dtb /mnt/tftp/972620/tftp-deploy-kkxy6haf/kernel/zImage eth0: 100Mbps full duplex link detected T eth0: DHCP client bound to address 10.8.254.196 Loading ARM Linux zImage '/mnt/tftp/972620/tftp-deploy-kkxy6haf/kernel/zImage' OS image not yet relocated Passing control to ARM zImage handler no OS load address, defaulting to 0x729a0000 no initrd load address, defaulting to 0x78000000 Loaded initrd GZIP compressed '/mnt/tftp/972620/tftp-deploy-kkxy6haf/ramdisk/ramdisk.cpio.gz' initrd is at 0x78000000-0x78cb9123 Loading devicetree from '/mnt/tftp/972620/tftp-deploy-kkxy6haf/dtb/imx53-qsrb.dtb' commandline: console=ttymxc0,115200n8 Starting kernel at 0x729a0000, initrd at 0x78000000, oftree at 0x78cba000... Starting kernel in secure mode [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.284-cip99 (KernelCI@build-j15426-arm-gcc-10-multi-v7-defconfig-jmc7v) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Fri Jun 9 14:54:24 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX53 Quick Start-R Board [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xcb800000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 261120 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 938652K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 44388K reserved, 65536K cma-reserved, 457624K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] TrustZone Interrupt Controller (TZIC) initialized [ 0.000000] CPU identified as i.MX53, silicon rev 2.1 [ 0.000000] Switching to timer-based delay loop, resolution 25ns [ 0.000010] sched_clock: 32 bits at 40MHz, resolution 25ns, wraps every 53687091187ns [ 0.000027] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 47781511156 ns [ 0.001974] Console: colour dummy device 80x30 [ 0.002043] Calibrating delay loop (skipped), value calculated using timer frequency.. 80.00 BogoMIPS (lpj=400000) [ 0.002061] pid_max: default: 32768 minimum: 301 [ 0.002216] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002232] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002977] CPU: Testing write buffer coherency: ok [ 0.003031] CPU0: Spectre v2: using BPIALL workaround [ 0.003479] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.004307] Setting up static identity map for 0x70300000 - 0x703000a0 [ 0.005389] rcu: Hierarchical SRCU implementation. [ 0.007336] EFI services will not be available. [ 0.007544] smp: Bringing up secondary CPUs ... [ 0.007556] smp: Brought up 1 node, 1 CPU [ 0.007566] SMP: Total of 1 processors activated (80.00 BogoMIPS). [ 0.007574] CPU: All CPU(s) started in SVC mode. [ 0.009348] devtmpfs: initialized [ 0.017146] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2 [ 0.017640] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.017670] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.021661] pinctrl core: initialized pinctrl subsystem [ 0.023553] DMI not present or invalid. [ 0.024391] NET: Registered protocol family 16 [ 0.027121] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.032022] cpuidle: using governor menu [ 0.032523] No ATAGs? [ 0.032533] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.034683] Serial: AMBA PL011 UART driver [ 0.043400] imx53-pinctrl 53fa8000.iomuxc: Failed to create dummy-iomuxc-gpr@53fa8000 debugfs directory [ 0.043703] imx53-pinctrl 53fa8000.iomuxc: initialized IMX pinctrl driver [ 0.080462] vgaarb: loaded [ 0.081582] SCSI subsystem initialized [ 0.082386] usbcore: registered new interface driver usbfs [ 0.082448] usbcore: registered new interface driver hub [ 0.082513] usbcore: registered new device driver usb [ 0.083910] i2c i2c-1: IMX I2C adapter registered [ 0.083938] i2c i2c-1: can't use DMA, using PIO instead. [ 0.084724] i2c i2c-0: IMX I2C adapter registered [ 0.084746] i2c i2c-0: can't use DMA, using PIO instead. [ 0.085904] pps_core: LinuxPPS API ver. 1 registered [ 0.085916] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.085942] PTP clock support registered [ 0.086152] EDAC MC: Ver: 3.0.0 [ 0.089303] clocksource: Switched to clocksource mxc_timer1 [ 0.161422] NET: Registered protocol family 2 [ 0.161740] IP idents hash table entries: 8192 (order: 4, 65536 bytes) [ 0.162392] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.162431] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.162477] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.162539] TCP: Hash tables configured (established 4096 bind 4096) [ 0.162706] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.162731] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.162905] NET: Registered protocol family 1 [ 0.163649] RPC: Registered named UNIX socket transport module. [ 0.163664] RPC: Registered udp transport module. [ 0.163671] RPC: Registered tcp transport module. [ 0.163678] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.164253] Trying to unpack rootfs image as initramfs... [ 1.117517] Freeing initrd memory: 13032K [ 1.118465] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 1.120587] Initialise system trusted keyrings [ 1.121252] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 1.128520] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.129590] NFS: Registering the id_resolver key type [ 1.129671] Key type id_resolver registered [ 1.129680] Key type id_legacy registered [ 1.129734] ntfs: driver 2.1.32 [Flags: R/O]. [ 1.132318] Key type asymmetric registered [ 1.132337] Asymmetric key parser 'x509' registered [ 1.132409] bounce: pool size: 64 pages [ 1.132477] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.132489] io scheduler noop registered [ 1.132498] io scheduler deadline registered [ 1.132692] io scheduler cfq registered (default) [ 1.132705] io scheduler mq-deadline registered [ 1.132713] io scheduler kyber registered [ 1.161641] imx-sdma 63fb0000.sdma: Direct firmware load for imx/sdma/sdma-imx53.bin failed with error -2 [ 1.161671] imx-sdma 63fb0000.sdma: external firmware not found, using ROM firmware [ 1.216124] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.220139] SuperH (H)SCI(F) driver initialized [ 1.220992] 53fbc000.serial: ttymxc0 at MMIO 0x53fbc000 (irq = 47, base_baud = 4166666) is a IMX [ 1.902241] console [ttymxc0] enabled [ 1.907286] msm_serial: driver initialized [ 1.911685] STMicroelectronics ASC driver initialized [ 1.918045] STM32 USART driver initialized [ 1.940408] brd: module loaded [ 1.952427] loop: module loaded [ 1.958708] ahci-imx 10000000.sata: hwmon0: sensor 'sata_ahci' [ 1.966882] ahci-imx 10000000.sata: SSS flag set, parallel bus scan disabled [ 1.974007] ahci-imx 10000000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.982909] ahci-imx 10000000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc [ 1.993024] scsi host0: ahci-imx [ 1.996834] ata1: SATA max UDMA/133 mmio [mem 0x10000000-0x10000fff] port 0x100 irq 44 [ 2.013843] CAN device driver interface [ 2.018695] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.025661] fec 63fec000.ethernet: 63fec000.ethernet supply phy not found, using dummy regulator [ 2.034639] fec 63fec000.ethernet: Linked as a consumer to regulator.0 [ 2.072686] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 2.078538] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.084706] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 2.091735] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.101529] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.109000] usbcore: registered new interface driver pegasus [ 2.114783] usbcore: registered new interface driver asix [ 2.120253] usbcore: registered new interface driver ax88179_178a [ 2.126380] usbcore: registered new interface driver cdc_ether [ 2.132289] usbcore: registered new interface driver smsc75xx [ 2.138082] usbcore: registered new interface driver smsc95xx [ 2.143891] usbcore: registered new interface driver net1080 [ 2.149618] usbcore: registered new interface driver cdc_subset [ 2.155573] usbcore: registered new interface driver zaurus [ 2.161255] usbcore: registered new interface driver cdc_ncm [ 2.169141] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.175749] ehci-pci: EHCI PCI platform driver [ 2.180308] ehci-platform: EHCI generic platform driver [ 2.185793] ehci-orion: EHCI orion driver [ 2.190034] SPEAr-ehci: EHCI SPEAr driver [ 2.194193] ehci-st: EHCI STMicroelectronics driver [ 2.199203] ehci-exynos: EHCI EXYNOS driver [ 2.203570] ehci-atmel: EHCI Atmel driver [ 2.207724] tegra-ehci: Tegra EHCI driver [ 2.211936] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.218161] ohci-pci: OHCI PCI platform driver [ 2.222711] ohci-platform: OHCI generic platform driver [ 2.228160] SPEAr-ohci: OHCI SPEAr driver [ 2.232389] ohci-st: OHCI STMicroelectronics driver [ 2.237415] ohci-atmel: OHCI Atmel driver [ 2.242271] usbcore: registered new interface driver usb-storage [ 2.254508] i2c /dev entries driver [ 2.269252] imx2-wdt 53f98000.wdog: timeout 60 sec (nowayout=0) [ 2.281693] sdhci: Secure Digital Host Controller Interface driver [ 2.287889] sdhci: Copyright(c) Pierre Ossman [ 2.294063] Synopsys Designware Multimedia Card Interface Driver [ 2.301610] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.333598] mmc0: SDHCI controller on 50004000.esdhc [50004000.esdhc] using ADMA [ 2.341962] sdhci-esdhc-imx 50020000.esdhc: Got CD GPIO [ 2.347224] sdhci-esdhc-imx 50020000.esdhc: Got WP GPIO [ 2.373135] ata1: SATA link down (SStatus 0 SControl 300) [ 2.378643] ahci-imx 10000000.sata: no device found, disabling link. [ 2.385118] ahci-imx 10000000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 2.394171] mmc1: SDHCI controller on 50020000.esdhc [50020000.esdhc] using ADMA [ 2.406304] ledtrig-cpu: registered to indicate activity on CPUs [ 2.413463] usbcore: registered new interface driver usbhid [ 2.419048] usbhid: USB HID core driver [ 2.428985] NET: Registered protocol family 10 [ 2.436968] Segment Routing with IPv6 [ 2.440841] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.447518] NET: Registered protocol family 17 [ 2.452065] can: controller area network core (rev 20170425 abi 9) [ 2.458345] NET: Registered protocol family 29 [ 2.462830] can: raw protocol (rev 20170425) [ 2.467107] can: broadcast manager protocol (rev 20170425 t) [ 2.472801] can: netlink gateway (rev 20170425) max_hops=1 [ 2.478961] Key type dns_resolver registered [ 2.483842] ThumbEE CPU extension supported. [ 2.488138] Registering SWP/SWPB emulation handler [ 2.494223] Loading compiled-in X.509 certificates [ 2.530280] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.537786] hctosys: unable to open rtc device (rtc0) [ 2.544130] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.563022] Freeing unused kernel memory: 2048K [ 2.567703] mmc0: new high speed SDHC card at address 0001 [ 2.574557] Run /init as init process [ 2.580548] mmcblk0: mmc0:0001 SD16G 14.6 GiB Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 2.806286] udevd[83]: starting version 3.2.9 [ 2.812420] random: udevd: uninitialized urandom read (16 bytes read) [ 2.819947] random: udevd: uninitialized urandom read (16 bytes read) [ 2.826545] random: udevd: uninitialized urandom read (16 bytes read) [ 2.843325] udevd[83]: specified user 'tss' unknown [ 2.848425] udevd[83]: specified group 'tss' unknown [ 2.858820] udevd[84]: starting eudev-3.2.9 [ 4.376517] usb_phy_generic usbphy-0: usbphy-0 supply vcc not found, using dummy regulator [ 4.385126] usb_phy_generic usbphy-0: Linked as a consumer to regulator.0 [ 4.392217] usb_phy_generic usbphy-1: usbphy-1 supply vcc not found, using dummy regulator [ 4.400632] usb_phy_generic usbphy-1: Linked as a consumer to regulator.0 [ 4.454219] imx_usb 53f80200.usb: Linked as a consumer to regulator.2 [ 4.496114] sgtl5000 1-000a: Linked as a consumer to regulator.1 [ 4.517872] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 4.522992] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 4.555062] sgtl5000 1-000a: sgtl5000 revision 0x11 [ 4.582303] sgtl5000 1-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 4.599645] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 4.616965] hub 1-0:1.0: USB hub found [ 4.634247] hub 1-0:1.0: 1 port detected done Saving random seed: [ 5.575744] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: OK Starting dropbear sshd: [ 5.710015] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-972620/environment . /lava-972620/environment / # /lava-972620/bin/lava-test-runner /lava-972620/0 /lava-972620/bin/lava-test-runner /lava-972620/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-972620/0/tests/0_dmesg + cat uuid + UUID=972620_1.5.2.3.1 [ 6.328809] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 6.389745] [ 6.444388] [ 6.498960] + set +x [ 6.509844] # / # #export SHELL=/bin/sh / # export SHELL=/bin/sh. /lava-972620/environment / # . /lava-972620/environment/lava-972620/bin/lava-test-runner /lava-972620/1 / # /lava-972620/bin/lava-test-runner /lava-972620/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-972620/1/tests/1_bootrr + cat uuid + UUID=972620_1.5.2.3.5 [ 7.027919] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-972620/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-972620/1/../bin/lava-test-case [ 7.101439] /lava-972620/1/../bin/lava-test-case [ 7.153967] /lava-972620/1/../bin/lava-test-case [ 7.185373] + set +x[ 7.209089] / #