[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.11 (5 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11367984/tftp-deploy-cgl45xmb/kernel/zImage tftp 0x10000000 11367984/tftp-deploy-cgl45xmb/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '11367984/tftp-deploy-cgl45xmb/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 5.1 MiB/s done Bytes transferred = 10433024 (9f3200 hex) => tftp 0x14000000 11367984/tftp-deploy-cgl45xmb/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11367984/tftp-deploy-cgl45xmb/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '11367984/tftp-deploy-cgl45xmb/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###### 4.8 MiB/s done Bytes transferred = 15354103 (ea48f7 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11367984/tftp-deploy-cgl45xmb/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11367984/tftp-deploy-cgl45xmb/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '11367984/tftp-deploy-cgl45xmb/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.2 MiB/s done Bytes transferred = 41818 (a35a hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x9f3200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15354039 Bytes = 14.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d359 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.292-cip102 (KernelCI@build-j24383-arm-gcc-10-multi-v7-defconfig-kselftest-qqt2s) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Sun Aug 27 23:29:55 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s40104 r8192 d21336 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 924548K/1048576K available (15360K kernel code, 1762K rwdata, 6316K rodata, 2048K init, 7700K bss, 58492K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (16352 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1763 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7701 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 49070 entries in 192 pages <6>[ 0.000000] ftrace: allocated 192 pages with 2 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022033] Console: colour dummy device 80x30 <4>[ 0.023923] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.031952] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.036294] ... MAX_LOCK_DEPTH: 48 <4>[ 0.040699] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.045310] ... CLASSHASH_SIZE: 4096 <4>[ 0.049950] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.054620] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.059345] ... CHAINHASH_SIZE: 32768 <4>[ 0.064016] memory used by lock dependency info: 4655 kB <4>[ 0.069697] per task-struct memory footprint: 1536 bytes <6>[ 0.075375] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.085799] CPU: Testing write buffer coherency: ok <6>[ 0.090902] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.096239] pid_max: default: 32768 minimum: 301 <6>[ 0.101401] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.108010] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.118101] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.123441] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.130278] rcu: Hierarchical SRCU implementation. <6>[ 0.137428] EFI services will not be available. <6>[ 0.140329] smp: Bringing up secondary CPUs ... <6>[ 0.146592] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.146604] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.158217] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.158228] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.169113] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.169125] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.178249] smp: Brought up 1 node, 4 CPUs <6>[ 0.182191] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.188702] CPU: All CPU(s) started in SVC mode. <6>[ 0.196344] devtmpfs: initialized <6>[ 0.231957] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.240232] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.247524] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.258023] pinctrl core: initialized pinctrl subsystem <6>[ 0.265825] DMI not present or invalid. <6>[ 0.268994] NET: Registered protocol family 16 <6>[ 0.280082] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.290794] cpuidle: using governor menu <6>[ 0.292612] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.333644] vdd1p1: supplied by regulator-dummy <6>[ 0.337619] vdd3p0: supplied by regulator-dummy <6>[ 0.342244] vdd2p5: supplied by regulator-dummy <6>[ 0.346998] vddarm: supplied by regulator-dummy <6>[ 0.352472] vddpu: supplied by regulator-dummy <6>[ 0.356014] vddsoc: supplied by regulator-dummy <6>[ 0.409356] No ATAGs? <6>[ 0.409826] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.417824] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.435494] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.443504] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.467793] Serial: AMBA PL011 UART driver <6>[ 0.569810] mxs-dma 110000.dma-apbh: initialized <6>[ 0.596343] vgaarb: loaded <5>[ 0.599432] SCSI subsystem initialized <6>[ 0.602004] usbcore: registered new interface driver usbfs <6>[ 0.606529] usbcore: registered new interface driver hub <6>[ 0.612111] usbcore: registered new device driver usb <6>[ 0.621976] i2c i2c-0: IMX I2C adapter registered <6>[ 0.624132] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.631590] i2c i2c-1: IMX I2C adapter registered <6>[ 0.634655] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.641563] i2c i2c-2: IMX I2C adapter registered <6>[ 0.645182] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.654845] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.657236] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.666734] PTP clock support registered <6>[ 0.671671] EDAC MC: Ver: 3.0.0 <6>[ 0.685037] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.953424] NET: Registered protocol family 2 <6>[ 0.955965] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.964428] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 20480 bytes) <6>[ 0.970394] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.977740] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) <6>[ 0.985702] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.991434] UDP hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.997329] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) <6>[ 1.004280] NET: Registered protocol family 1 <6>[ 1.010311] RPC: Registered named UNIX socket transport module. <6>[ 1.014464] RPC: Registered udp transport module. <6>[ 1.019505] RPC: Registered tcp transport module. <6>[ 1.024375] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.033016] Trying to unpack rootfs image as initramfs... <6>[ 2.804895] Freeing initrd memory: 14996K <4>[ 2.807355] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 2.814557] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 2.829870] Initialise system trusted keyrings <6>[ 2.832699] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.867131] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.873150] NFS: Registering the id_resolver key type <5>[ 2.875890] Key type id_resolver registered <5>[ 2.880150] Key type id_legacy registered <6>[ 2.884549] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.896596] Key type asymmetric registered <5>[ 2.898186] Asymmetric key parser 'x509' registered <6>[ 2.903526] bounce: pool size: 64 pages <6>[ 2.907520] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 2.915098] io scheduler noop registered <6>[ 2.919177] io scheduler deadline registered <6>[ 2.924175] io scheduler cfq registered (default) <6>[ 2.928714] io scheduler mq-deadline registered <6>[ 2.933447] io scheduler kyber registered <4>[ 2.938336] test_firmware: interface ready <6>[ 3.018521] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.023528] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.030989] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.037817] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.090855] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 3.094528] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 3.102320] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 3.108647] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 3.116604] PU : no governor for states <6>[ 3.120173] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <4>[ 3.152447] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.159614] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.339476] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.355955] SuperH (H)SCI(F) driver initialized <6>[ 3.360122] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 3.369675] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 3.378789] console [ttymxc1] enabled <6>[ 3.378789] console [ttymxc1] enabled <6>[ 3.383810] bootconsole [ec_imx21] disabled <6>[ 3.383810] bootconsole [ec_imx21] disabled <6>[ 3.396999] msm_serial: driver initialized <6>[ 3.402217] STMicroelectronics ASC driver initialized <6>[ 3.412842] STM32 USART driver initialized <6>[ 3.432813] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 3.457761] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.466742] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.473999] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.481081] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.490373] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.497963] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.534552] brd: module loaded <6>[ 3.567274] loop: module loaded <6>[ 3.580609] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.588876] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.597225] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.605734] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 3.617137] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.624412] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.633568] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.646747] scsi host0: ahci-imx <6>[ 3.652101] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 3.697304] CAN device driver interface <6>[ 3.704879] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 3.713919] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 3.723155] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 3.733400] pps pps0: new PPS source ptp0 <6>[ 3.781703] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.791097] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 3.797267] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.803658] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 3.810952] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.833964] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.841819] usbcore: registered new interface driver pegasus <6>[ 3.847966] usbcore: registered new interface driver asix <6>[ 3.853751] usbcore: registered new interface driver ax88179_178a <6>[ 3.860280] usbcore: registered new interface driver cdc_ether <6>[ 3.866613] usbcore: registered new interface driver smsc75xx <6>[ 3.872795] usbcore: registered new interface driver smsc95xx <6>[ 3.878981] usbcore: registered new interface driver net1080 <6>[ 3.885086] usbcore: registered new interface driver cdc_subset <6>[ 3.891397] usbcore: registered new interface driver zaurus <6>[ 3.897744] usbcore: registered new interface driver cdc_ncm <6>[ 3.912372] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.919243] ehci-pci: EHCI PCI platform driver <6>[ 3.924099] ehci-platform: EHCI generic platform driver <6>[ 3.930480] ehci-orion: EHCI orion driver <6>[ 3.935562] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.940539] ehci-st: EHCI STMicroelectronics driver <6>[ 3.946433] ehci-exynos: EHCI EXYNOS driver <6>[ 3.951570] ehci-atmel: EHCI Atmel driver <6>[ 3.956583] tegra-ehci: Tegra EHCI driver <6>[ 3.961590] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.968156] ohci-pci: OHCI PCI platform driver <6>[ 3.973005] ohci-platform: OHCI generic platform driver <6>[ 3.979354] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.984342] ohci-st: OHCI STMicroelectronics driver <6>[ 3.987325] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.990255] ohci-atmel: OHCI Atmel driver <6>[ 3.995351] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.002290] usbcore: registered new interface driver usb-storage <6>[ 4.006122] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.018835] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 4.036733] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 4.048689] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.054068] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.085112] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.094747] hub 1-0:1.0: USB hub found <6>[ 4.099198] hub 1-0:1.0: 1 port detected <6>[ 4.126157] i2c /dev entries driver <6>[ 4.178329] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 4.200127] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.206646] sdhci: Copyright(c) Pierre Ossman <6>[ 4.217790] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.230162] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.238280] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 4.243798] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 4.249753] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 4.293527] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 4.302332] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 4.308296] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 4.349790] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 4.369344] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.378757] usbcore: registered new interface driver usbhid <6>[ 4.384660] usbhid: USB HID core driver <6>[ 4.393466] mmc0: new high speed SDHC card at address 0001 <6>[ 4.403674] mmcblk0: mmc0:0001 SD 14.6 GiB <6>[ 4.406926] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.409549] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.415661] IPv4 over IPsec tunneling driver <6>[ 4.429411] NET: Registered protocol family 10 <6>[ 4.437932] Segment Routing with IPv6 <6>[ 4.444226] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.454604] NET: Registered protocol family 17 <6>[ 4.459689] can: controller area network core (rev 20170425 abi 9) <6>[ 4.466585] NET: Registered protocol family 29 <6>[ 4.471330] can: raw protocol (rev 20170425) <6>[ 4.476035] can: broadcast manager protocol (rev 20170425 t) <6>[ 4.482069] can: netlink gateway (rev 20170425) max_hops=1 <6>[ 4.488646] 8021q: 802.1Q VLAN Support v1.8 <5>[ 4.493861] Key type dns_resolver registered <6>[ 4.507656] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 4.513637] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 4.519667] cpu cpu0: Linked as a consumer to regulator.6 <4>[ 4.525032] ------------[ cut here ]------------ <6>[ 4.529961] ThumbEE CPU extension supported. <4>[ 4.530243] WARNING: CPU: 1 PID: 0 at include/trace/events/lock.h:13 lock_acquire+0x138/0x1f0 <4>[ 4.530251] Modules linked in: <5>[ 4.534813] Registering SWP/SWPB emulation handler <4>[ 4.536105] ------------[ cut here ]------------ <4>[ 4.536138] WARNING: CPU: 3 PID: 0 at include/trace/events/lock.h:58 lock_release+0x364/0x370 <4>[ 4.536146] Modules linked in: <4>[ 4.536172] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.19.292-cip102 #1 <4>[ 4.536183] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 4.536191] Backtrace: <4>[ 4.536229] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 4.536251] r7:ffffffff r6:00000000 r5:60000093 r4:c1c9d72c <4>[ 4.536281] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 4.536306] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <4>[ 4.536328] r9:c03ff6d8 r8:00000003 r7:60000093 r6:00000009 r5:00000000 r4:00000000 <4>[ 4.536350] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 4.536366] r6:c03b8ae8 r5:0000003a r4:c1681e10 <4>[ 4.536390] [] (warn_slowpath_null) from [] (lock_release+0x364/0x370) <4>[ 4.536405] r6:c1b456c4 r5:c1b456c4 r4:c1b084bc <4>[ 4.536430] [] (lock_release) from [] (ktime_get+0x84/0x1ac) <4>[ 4.536452] r10:00000001 r9:60000093 r8:00000003 r7:c1b45700 r6:c1b456c4 r5:c03ff6d8 <4>[ 4.536463] r4:c1b45600 <4>[ 4.536488] [] (ktime_get) from [] (clockevents_program_event+0x6c/0x184) <4>[ 4.536508] r10:ef7cd2f8 r9:c23e9b00 r8:00000003 r7:37fe7a74 r6:00000001 r5:00000001 <4>[ 4.536517] r4:ee829c40 <4>[ 4.536542] [] (clockevents_program_event) from [] (tick_broadcast_set_event+0x54/0xb4) <4>[ 4.536558] r7:37fe7a74 r6:00000001 r5:00000003 r4:ee829c40 <4>[ 4.536584] [] (tick_broadcast_set_event) from [] (__tick_broadcast_oneshot_control+0x140/0x2ac) <4>[ 4.536600] r7:ef7d1740 r6:ee829c40 r5:00000000 r4:00000003 <4>[ 4.536623] [] (__tick_broadcast_oneshot_control) from [] (tick_broadcast_oneshot_control+0x3c/0x40) <4>[ 4.536644] r9:ef7cd2f8 r8:00000001 r7:c1b10e94 r6:c1b10ea4 r5:c1b10e44 r4:00000001 <4>[ 4.536670] [] (tick_broadcast_oneshot_control) from [] (cpuidle_enter_state+0x50/0x520) <4>[ 4.536691] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 4.536712] r10:ef7cd2f8 r9:c1b10e44 r8:c1aa22f0 r7:c1b08500 r6:c1b10e44 r5:ef7cd2f8 <4>[ 4.536721] r4:00000001 <4>[ 4.536755] [] (cpuidle_enter) from [] (do_idle+0x20c/0x2f8) <4>[ 4.536771] r7:c1b08500 r6:c1b084bc r5:00000003 r4:ee9da000 <4>[ 4.536797] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 4.536817] r10:00000000 r9:412fc09a r8:1020406a r7:c1cb9650 r6:00000003 r5:ee9da000 <4>[ 4.536826] r4:00000089 <4>[ 4.536859] [] (cpu_startup_entry) from [] (secondary_start_kernel+0x170/0x17c) <4>[ 4.536882] [] (secondary_start_kernel) from [<1030312c>] (0x1030312c) <4>[ 4.536899] r7:c1cb9650 r6:10c0387d r5:00000051 r4:3e9c406a <4>[ 4.536909] irq event stamp: 4702 <4>[ 4.536939] hardirqs last enabled at (4701): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 4.536962] hardirqs last disabled at (4702): [] do_idle+0xb0/0x2f8 <4>[ 4.536992] softirqs last enabled at (4694): [] _local_bh_enable+0x34/0x68 <4>[ 4.537013] softirqs last disabled at (4693): [] irq_enter+0x6c/0x94 <4>[ 4.537069] ---[ end trace 0e9ad3e7b4964ca6 ]--- <4>[ 4.543582] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G W 4.19.292-cip102 #1 <4>[ 4.543593] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 4.543600] Backtrace: <4>[ 4.543633] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 4.543652] r7:ffffffff r6:00000000 r5:60000093 r4:c1c9d72c <4>[ 4.543681] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 4.543705] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <4>[ 4.543726] r9:60000093 r8:c1b084bc r7:00000000 r6:00000009 r5:00000000 r4:00000000 <5>[ 4.553466] Loading compiled-in X.509 certificates <4>[ 4.557004] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 4.557020] r6:c03b8c2c r5:0000000d r4:c1681e10 <4>[ 4.557046] [] (warn_slowpath_null) from [] (lock_acquire+0x138/0x1f0) <4>[ 4.557060] r6:00000000 r5:00000000 r4:c1b05990 <4>[ 4.557091] [] (lock_acquire) from [] (_raw_spin_lock+0x58/0x68) <4>[ 4.557112] r10:ef7ab2f8 r9:ef7ab2f8 r8:00000001 r7:ef7af740 r6:00000001 r5:c23e9aec <4>[ 4.557122] r4:c1b05980 <4>[ 4.557152] [] (_raw_spin_lock) from [] (__tick_broadcast_oneshot_control+0x4c/0x2ac) <4>[ 4.557169] r4:ee9d7ee8 <4>[ 4.983030] [] (__tick_broadcast_oneshot_control) from [] (tick_broadcast_oneshot_control+0x3c/0x40) <4>[ 4.994194] r9:ef7ab2f8 r8:00000001 r7:c1b10e94 r6:c1b10ea4 r5:c1b10e44 r4:00000001 <4>[ 5.002237] [] (tick_broadcast_oneshot_control) from [] (cpuidle_enter_state+0x50/0x520) <4>[ 5.012356] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 5.020911] r10:ef7ab2f8 r9:c1b10e44 r8:c1aa22f0 r7:c1b08500 r6:c1b10e44 r5:ef7ab2f8 <4>[ 5.029018] r4:00000001 <4>[ 5.031860] [] (cpuidle_enter) from [] (do_idle+0x20c/0x2f8) <4>[ 5.039543] r7:c1b08500 r6:c1b084bc r5:00000001 r4:ee9d6000 <4>[ 5.045502] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 5.053359] r10:00000000 r9:412fc09a r8:1020406a r7:c1cb9650 r6:00000001 r5:ee9d6000 <4>[ 5.061467] r4:00000089 <4>[ 5.064304] [] (cpu_startup_entry) from [] (secondary_start_kernel+0x170/0x17c) <4>[ 5.073642] [] (secondary_start_kernel) from [<1030312c>] (0x1030312c) <4>[ 5.081325] r7:c1cb9650 r6:10c0387d r5:00000051 r4:3e9c406a <4>[ 5.087263] irq event stamp: 10782 <4>[ 5.090969] hardirqs last enabled at (10781): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 5.100133] hardirqs last disabled at (10782): [] do_idle+0xb0/0x2f8 <4>[ 5.107655] softirqs last enabled at (10774): [] _local_bh_enable+0x34/0x68 <4>[ 5.115861] softirqs last disabled at (10773): [] irq_enter+0x6c/0x94 <4>[ 5.123449] ---[ end trace 0e9ad3e7b4964ca8 ]--- <6>[ 5.132710] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.140660] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.152743] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.160569] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.173002] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.182018] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.189406] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.200512] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.209844] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.217500] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.224620] hub 1-1:1.0: USB hub found <6>[ 5.229113] hub 1-1:1.0: 3 ports detected <6>[ 5.231559] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 5.246565] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.254291] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.266046] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.273804] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.286286] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.295179] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.302436] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.313459] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.322753] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.330288] panel-simple panel-lvds0: Dropping the link to regulator.0 <4>[ 5.339223] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 5.341371] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <4>[ 5.347089] GPT:7812499 != 30560255 <6>[ 5.354589] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <4>[ 5.358157] GPT:Alternate GPT header not at the end of the disk. <4>[ 5.358168] GPT:7812499 != 30560255 <4>[ 5.358177] GPT: Use GNU Parted to correct GPT errors. <6>[ 5.369702] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.371584] mmcblk0: p1 p2 p3 <6>[ 5.375579] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.403879] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.412961] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.420246] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.431236] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.440495] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.447915] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.458435] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.466062] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.477647] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.485348] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 5.499473] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 5.507559] hctosys: unable to open rtc device (rtc0) <4>[ 5.518118] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.527154] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.534406] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.545495] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.554692] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.562095] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.572615] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.580231] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.591848] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.599547] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 5.637286] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 5.653835] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 7.707144] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 7.725180] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.755913] Sending DHCP requests ., OK <6>[ 7.799662] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.11 <6>[ 7.808059] IP-Config: Complete: <6>[ 7.811577] device=eth0, hwaddr=00:19:b8:07:40:03, ipaddr=192.168.201.11, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.822369] host=imx6q-sabrelite-lava-cbg-0, domain=lava-rack, nis-domain=(none) <6>[ 7.830543] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.830552] nameserver0=192.168.201.1 <6>[ 7.895255] Freeing unused kernel memory: 2048K <6>[ 7.905689] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.248188] udevd[109]: starting version 3.2.9 <5>[ 8.256463] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.264249] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.271790] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.290221] udevd[109]: specified user 'tss' unknown <27>[ 8.295802] udevd[109]: specified group 'tss' unknown <30>[ 8.307467] udevd[110]: starting eudev-3.2.9 <4>[ 9.270449] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 9.279515] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 9.315076] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 9.321810] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <4>[ 9.332570] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 9.338016] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 9.345705] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 9.353964] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 9.360673] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 9.375058] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 9.389664] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 9.392257] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 9.404795] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 9.408448] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 9.411760] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 9.419452] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 9.438028] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 9.447023] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 9.454220] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 9.465557] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 9.474791] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 9.482252] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 9.509086] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 9.533302] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 9.539799] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 9.552405] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 1 <6>[ 9.562349] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 9.570935] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 9.583217] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 9.591031] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 9.603807] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 9.612939] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 9.620241] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 9.631929] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 9.641291] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 9.648797] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 9.665390] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 9.673137] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 9.682527] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 9.689202] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 9.696390] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 9.701397] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 9.704092] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 9.722069] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 9.731030] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 9.738315] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 9.749814] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 9.759133] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 9.760512] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 9.768901] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 9.822964] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 9.830666] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 9.842761] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 9.850533] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 9.863620] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 9.872702] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 9.880007] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 9.891934] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 9.901497] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 9.908954] panel-simple panel-lvds0: Dropping the link to regulator.0 done Saving random seed: <5>[ 10.359313] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 10.609210] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11367984/environment . /lava-11367984/environment / # /lava-11367984/bin/lava-test-runner /lava-11367984/0 /lava-11367984/bin/lava-test-runner /lava-11367984/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-11367984/0/tests/0_dmesg + cat uuid + UUID=11367984_1.5.2.4.1<8>[ 11.347083] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 11.456286] <8>[ 11.554727] <8>[ 11.649756] + set +x <8>[ 11.661240] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11367984/environment / # . /lava-11367984/environment/lava-11367984/bin/lava-test-runner /lava-11367984/1 / # /lava-11367984/bin/lava-test-runner /lava-11367984/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-11367984/1/tests/1_bootrr + cat uuid + UUID=11367984_1.5.2.4.5<8>[ 12.274892] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11367984/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd panel-lvds0 /lava-11367984/1/../bin/lava-test-case <8>[ 13.441577] /lava-11367984/1/../bin/lava-test-case <8>[ 13.544329] /lava-11367984/1/../bin/lava-test-case <8>[ 13.600203] + set +x <8>[ 13.639461] / #