[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.11 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11637462/tftp-deploy-w3s3qnuw/kernel/zImage tftp 0x10000000 11637462/tftp-deploy-w3s3qnuw/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '11637462/tftp-deploy-w3s3qnuw/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 5.6 MiB/s done Bytes transferred = 10433024 (9f3200 hex) => tftp 0x14000000 11637462/tftp-deploy-w3s3qnuw/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11637462/tftp-deploy-w3s3qnuw/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '11637462/tftp-deploy-w3s3qnuw/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###### 3.7 MiB/s done Bytes transferred = 15353807 (ea47cf hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11637462/tftp-deploy-w3s3qnuw/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11637462/tftp-deploy-w3s3qnuw/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '11637462/tftp-deploy-w3s3qnuw/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.2 MiB/s done Bytes transferred = 41818 (a35a hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x9f3200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15353743 Bytes = 14.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d359 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.295-cip103 (KernelCI@build-j60818-arm-gcc-10-multi-v7-defconfig-kselftest-s2kwm) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Thu Sep 28 23:50:18 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s40104 r8192 d21336 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 924548K/1048576K available (15360K kernel code, 1762K rwdata, 6316K rodata, 2048K init, 7700K bss, 58492K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (16352 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1763 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7701 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 49070 entries in 192 pages <6>[ 0.000000] ftrace: allocated 192 pages with 2 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008446] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022008] Console: colour dummy device 80x30 <4>[ 0.023893] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.031919] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.036264] ... MAX_LOCK_DEPTH: 48 <4>[ 0.040670] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.045281] ... CLASSHASH_SIZE: 4096 <4>[ 0.049920] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.054590] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.059316] ... CHAINHASH_SIZE: 32768 <4>[ 0.063987] memory used by lock dependency info: 4655 kB <4>[ 0.069670] per task-struct memory footprint: 1536 bytes <6>[ 0.075349] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.085770] CPU: Testing write buffer coherency: ok <6>[ 0.090874] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.096211] pid_max: default: 32768 minimum: 301 <6>[ 0.101366] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.107979] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.118067] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.123373] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.130237] rcu: Hierarchical SRCU implementation. <6>[ 0.137394] EFI services will not be available. <6>[ 0.140270] smp: Bringing up secondary CPUs ... <6>[ 0.146549] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.146562] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.158149] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.158161] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.169063] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.169075] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.178267] smp: Brought up 1 node, 4 CPUs <6>[ 0.182159] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.188680] CPU: All CPU(s) started in SVC mode. <6>[ 0.196224] devtmpfs: initialized <6>[ 0.231471] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.239255] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.246811] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.257105] pinctrl core: initialized pinctrl subsystem <6>[ 0.264692] DMI not present or invalid. <6>[ 0.267928] NET: Registered protocol family 16 <6>[ 0.279168] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.289839] cpuidle: using governor menu <6>[ 0.291653] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.331495] vdd1p1: supplied by regulator-dummy <6>[ 0.335435] vdd3p0: supplied by regulator-dummy <6>[ 0.340071] vdd2p5: supplied by regulator-dummy <6>[ 0.344791] vddarm: supplied by regulator-dummy <6>[ 0.350280] vddpu: supplied by regulator-dummy <6>[ 0.353839] vddsoc: supplied by regulator-dummy <6>[ 0.405959] No ATAGs? <6>[ 0.406442] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.414443] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.431861] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.439866] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.463759] Serial: AMBA PL011 UART driver <6>[ 0.563235] mxs-dma 110000.dma-apbh: initialized <6>[ 0.589272] vgaarb: loaded <5>[ 0.592277] SCSI subsystem initialized <6>[ 0.594837] usbcore: registered new interface driver usbfs <6>[ 0.599460] usbcore: registered new interface driver hub <6>[ 0.604895] usbcore: registered new device driver usb <6>[ 0.614656] i2c i2c-0: IMX I2C adapter registered <6>[ 0.616863] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.624207] i2c i2c-1: IMX I2C adapter registered <6>[ 0.627382] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.634162] i2c i2c-2: IMX I2C adapter registered <6>[ 0.637911] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.647418] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.649808] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.659306] PTP clock support registered <6>[ 0.664174] EDAC MC: Ver: 3.0.0 <6>[ 0.677797] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.940303] NET: Registered protocol family 2 <6>[ 0.942762] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.951350] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 20480 bytes) <6>[ 0.957173] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.964638] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) <6>[ 0.972464] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.978353] UDP hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.984138] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.991249] NET: Registered protocol family 1 <6>[ 0.997010] RPC: Registered named UNIX socket transport module. <6>[ 1.001426] RPC: Registered udp transport module. <6>[ 1.006296] RPC: Registered tcp transport module. <6>[ 1.011310] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.019901] Trying to unpack rootfs image as initramfs... <6>[ 2.776353] Freeing initrd memory: 14996K <4>[ 2.778861] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 2.786020] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 2.801233] Initialise system trusted keyrings <6>[ 2.803901] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.837717] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.843635] NFS: Registering the id_resolver key type <5>[ 2.846418] Key type id_resolver registered <5>[ 2.850813] Key type id_legacy registered <6>[ 2.855162] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.867213] Key type asymmetric registered <5>[ 2.868872] Asymmetric key parser 'x509' registered <6>[ 2.874128] bounce: pool size: 64 pages <6>[ 2.878106] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 2.885662] io scheduler noop registered <6>[ 2.889841] io scheduler deadline registered <6>[ 2.894775] io scheduler cfq registered (default) <6>[ 2.899324] io scheduler mq-deadline registered <6>[ 2.904062] io scheduler kyber registered <4>[ 2.908936] test_firmware: interface ready <6>[ 2.987494] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.992564] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.999932] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.006724] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.059237] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 3.062912] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 3.070615] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 3.076965] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 3.084960] PU : no governor for states <6>[ 3.088592] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <4>[ 3.120237] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.127319] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.314618] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.330954] SuperH (H)SCI(F) driver initialized <6>[ 3.335077] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 3.344574] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 3.353735] console [ttymxc1] enabled <6>[ 3.353735] console [ttymxc1] enabled <6>[ 3.358838] bootconsole [ec_imx21] disabled <6>[ 3.358838] bootconsole [ec_imx21] disabled <6>[ 3.371654] msm_serial: driver initialized <6>[ 3.376876] STMicroelectronics ASC driver initialized <6>[ 3.387408] STM32 USART driver initialized <6>[ 3.407334] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 3.432035] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.441000] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.448347] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.455366] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.464666] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.472252] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.508394] brd: module loaded <6>[ 3.540640] loop: module loaded <6>[ 3.553731] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.562040] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.570389] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.578947] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 3.590314] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.597590] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.606762] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.619816] scsi host0: ahci-imx <6>[ 3.625175] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 3.669592] CAN device driver interface <6>[ 3.677144] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 3.686117] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 3.695380] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 3.705601] pps pps0: new PPS source ptp0 <6>[ 3.753521] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.762859] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 3.769028] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.775398] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 3.782689] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.805380] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.813226] usbcore: registered new interface driver pegasus <6>[ 3.819380] usbcore: registered new interface driver asix <6>[ 3.825166] usbcore: registered new interface driver ax88179_178a <6>[ 3.831696] usbcore: registered new interface driver cdc_ether <6>[ 3.838006] usbcore: registered new interface driver smsc75xx <6>[ 3.844177] usbcore: registered new interface driver smsc95xx <6>[ 3.850383] usbcore: registered new interface driver net1080 <6>[ 3.856428] usbcore: registered new interface driver cdc_subset <6>[ 3.862781] usbcore: registered new interface driver zaurus <6>[ 3.869136] usbcore: registered new interface driver cdc_ncm <6>[ 3.883593] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.890464] ehci-pci: EHCI PCI platform driver <6>[ 3.895301] ehci-platform: EHCI generic platform driver <6>[ 3.901663] ehci-orion: EHCI orion driver <6>[ 3.906661] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.911708] ehci-st: EHCI STMicroelectronics driver <6>[ 3.917550] ehci-exynos: EHCI EXYNOS driver <6>[ 3.922735] ehci-atmel: EHCI Atmel driver <6>[ 3.927726] tegra-ehci: Tegra EHCI driver <6>[ 3.932715] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.939284] ohci-pci: OHCI PCI platform driver <6>[ 3.944126] ohci-platform: OHCI generic platform driver <6>[ 3.950442] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.955403] ohci-st: OHCI STMicroelectronics driver <6>[ 3.960260] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.961297] ohci-atmel: OHCI Atmel driver <6>[ 3.966350] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.973340] usbcore: registered new interface driver usb-storage <6>[ 3.977157] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.989784] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 4.007801] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 4.019566] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.024930] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.057766] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.067285] hub 1-0:1.0: USB hub found <6>[ 4.071733] hub 1-0:1.0: 1 port detected <6>[ 4.098134] i2c /dev entries driver <6>[ 4.149555] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 4.171009] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.177476] sdhci: Copyright(c) Pierre Ossman <6>[ 4.188480] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.200731] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.208522] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 4.214039] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 4.219998] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 4.262623] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 4.271412] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 4.277278] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 4.316962] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 4.336258] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.345636] usbcore: registered new interface driver usbhid <6>[ 4.351609] usbhid: USB HID core driver <6>[ 4.368404] mmc0: new high speed SDHC card at address 0001 <6>[ 4.373588] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.378703] mmcblk0: mmc0:0001 SD 14.6 GiB <6>[ 4.381702] IPv4 over IPsec tunneling driver <6>[ 4.392878] NET: Registered protocol family 10 <6>[ 4.401334] Segment Routing with IPv6 <6>[ 4.407598] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.417798] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.417967] NET: Registered protocol family 17 <6>[ 4.430157] can: controller area network core (rev 20170425 abi 9) <6>[ 4.436883] NET: Registered protocol family 29 <6>[ 4.441681] can: raw protocol (rev 20170425) <6>[ 4.446325] can: broadcast manager protocol (rev 20170425 t) <6>[ 4.452350] can: netlink gateway (rev 20170425) max_hops=1 <6>[ 4.458888] 8021q: 802.1Q VLAN Support v1.8 <5>[ 4.464092] Key type dns_resolver registered <4>[ 4.477766] ------------[ cut here ]------------ <6>[ 4.479719] cpu cpu0: Linked as a consumer to regulator.4 <4>[ 4.482672] WARNING: CPU: 1 PID: 0 at include/trace/events/lock.h:13 lock_acquire+0x138/0x1f0 <4>[ 4.482680] Modules linked in: <6>[ 4.488791] cpu cpu0: Linked as a consumer to regulator.5 <4>[ 4.497139] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.19.295-cip103 #1 <6>[ 4.500783] cpu cpu0: Linked as a consumer to regulator.6 <4>[ 4.506110] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 4.506117] Backtrace: <6>[ 4.517612] ThumbEE CPU extension supported. <4>[ 4.518769] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 4.518776] ------------[ cut here ]------------ <4>[ 4.518811] WARNING: CPU: 3 PID: 0 at include/trace/events/lock.h:58 lock_release+0x364/0x370 <4>[ 4.518815] r7:ffffffff r6:00000000 r5:60000093 r4:c1c9d72c <4>[ 4.518820] Modules linked in: <4>[ 4.518848] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 4.518885] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <5>[ 4.525721] Registering SWP/SWPB emulation handler <4>[ 4.528390] r9:60000093 r8:c1b084bc r7:00000000 r6:00000009 r5:00000000 r4:00000000 <4>[ 4.528413] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 4.528428] r6:c03b8c74 r5:0000000d r4:c1681ef4 <4>[ 4.528450] [] (warn_slowpath_null) from [] (lock_acquire+0x138/0x1f0) <4>[ 4.528464] r6:00000000 r5:00000000 r4:c1b05990 <4>[ 4.528508] [] (lock_acquire) from [] (_raw_spin_lock+0x58/0x68) <5>[ 4.539672] Loading compiled-in X.509 certificates <4>[ 4.540875] r10:ef7ab2f8 r9:ef7ab2f8 r8:00000001 r7:ef7af740 r6:00000001 r5:c23e9aec <4>[ 4.640074] r4:c1b05980 <4>[ 4.642914] [] (_raw_spin_lock) from [] (__tick_broadcast_oneshot_control+0x4c/0x2ac) <4>[ 4.652760] r4:ee9d7ee8 <4>[ 4.655587] [] (__tick_broadcast_oneshot_control) from [] (tick_broadcast_oneshot_control+0x3c/0x40) <4>[ 4.666747] r9:ef7ab2f8 r8:00000001 r7:c1b10e94 r6:c1b10ea4 r5:c1b10e44 r4:00000001 <4>[ 4.674789] [] (tick_broadcast_oneshot_control) from [] (cpuidle_enter_state+0x50/0x520) <4>[ 4.684907] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 4.693463] r10:ef7ab2f8 r9:c1b10e44 r8:c1aa22f0 r7:c1b08500 r6:c1b10e44 r5:ef7ab2f8 <4>[ 4.701569] r4:00000001 <4>[ 4.704408] [] (cpuidle_enter) from [] (do_idle+0x20c/0x2f8) <4>[ 4.712088] r7:c1b08500 r6:c1b084bc r5:00000001 r4:ee9d6000 <4>[ 4.718046] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 4.725906] r10:00000000 r9:412fc09a r8:1020406a r7:c1cb9650 r6:00000001 r5:ee9d6000 <4>[ 4.734013] r4:00000089 <4>[ 4.736852] [] (cpu_startup_entry) from [] (secondary_start_kernel+0x170/0x17c) <4>[ 4.746192] [] (secondary_start_kernel) from [<1030312c>] (0x1030312c) <4>[ 4.753876] r7:c1cb9650 r6:10c0387d r5:00000051 r4:3e9c406a <4>[ 4.759815] irq event stamp: 18494 <4>[ 4.759828] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.19.295-cip103 #1 <4>[ 4.759842] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 4.763523] hardirqs last enabled at (18493): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 4.763553] hardirqs last disabled at (18494): [] do_idle+0xb0/0x2f8 <4>[ 4.770508] Backtrace: <4>[ 4.777321] softirqs last enabled at (18486): [] __do_softirq+0x344/0x520 <4>[ 4.786465] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 4.793956] softirqs last disabled at (18465): [] irq_exit+0x170/0x1c8 <4>[ 4.796650] r7:ffffffff r6:00000000 r5:60000093 r4:c1c9d72c <4>[ 4.804652] ---[ end trace 941dc0d0a43c239f ]--- <4>[ 4.812508] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 4.838544] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <4>[ 4.846315] r9:c03ff720 r8:00000003 r7:60000093 r6:00000009 r5:00000000 r4:00000000 <4>[ 4.854350] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 4.862810] r6:c03b8b30 r5:0000003a r4:c1681ef4 <4>[ 4.867722] [] (warn_slowpath_null) from [] (lock_release+0x364/0x370) <4>[ 4.876268] r6:c1b456c4 r5:c1b456c4 r4:c1b084bc <4>[ 4.881181] [] (lock_release) from [] (ktime_get+0x84/0x1ac) <4>[ 4.888864] r10:00000001 r9:60000093 r8:00000003 r7:c1b45700 r6:c1b456c4 r5:c03ff720 <4>[ 4.896971] r4:c1b45600 <4>[ 4.899797] [] (ktime_get) from [] (clockevents_program_event+0x6c/0x184) <4>[ 4.908608] r10:ef7cd2f8 r9:c23e9b00 r8:00000003 r7:3696dbf4 r6:00000001 r5:00000001 <4>[ 4.916713] r4:ee829c40 <4>[ 4.919538] [] (clockevents_program_event) from [] (tick_broadcast_set_event+0x54/0xb4) <4>[ 4.929561] r7:3696dbf4 r6:00000001 r5:00000003 r4:ee829c40 <4>[ 4.935513] [] (tick_broadcast_set_event) from [] (__tick_broadcast_oneshot_control+0x140/0x2ac) <4>[ 4.946317] r7:ef7d1740 r6:ee829c40 r5:00000000 r4:00000003 <4>[ 4.952267] [] (__tick_broadcast_oneshot_control) from [] (tick_broadcast_oneshot_control+0x3c/0x40) <4>[ 4.963421] r9:ef7cd2f8 r8:00000001 r7:c1b10e94 r6:c1b10ea4 r5:c1b10e44 r4:00000001 <4>[ 4.971456] [] (tick_broadcast_oneshot_control) from [] (cpuidle_enter_state+0x50/0x520) <4>[ 4.981571] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 4.990123] r10:ef7cd2f8 r9:c1b10e44 r8:c1aa22f0 r7:c1b08500 r6:c1b10e44 r5:ef7cd2f8 <4>[ 4.998228] r4:00000001 <4>[ 5.001057] [] (cpuidle_enter) from [] (do_idle+0x20c/0x2f8) <4>[ 5.008736] r7:c1b08500 r6:c1b084bc r5:00000003 r4:ee9da000 <4>[ 5.014686] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 5.022543] r10:00000000 r9:412fc09a r8:1020406a r7:c1cb9650 r6:00000003 r5:ee9da000 <4>[ 5.030649] r4:00000089 <4>[ 5.033479] [] (cpu_startup_entry) from [] (secondary_start_kernel+0x170/0x17c) <4>[ 5.042812] [] (secondary_start_kernel) from [<1030312c>] (0x1030312c) <4>[ 5.050491] r7:c1cb9650 r6:10c0387d r5:00000051 r4:3e9c406a <4>[ 5.056426] irq event stamp: 10924 <4>[ 5.060122] hardirqs last enabled at (10923): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 5.069284] hardirqs last disabled at (10924): [] do_idle+0xb0/0x2f8 <4>[ 5.076799] softirqs last enabled at (10916): [] _local_bh_enable+0x34/0x68 <4>[ 5.085003] softirqs last disabled at (10915): [] irq_enter+0x6c/0x94 <4>[ 5.092589] ---[ end trace 941dc0d0a43c23a0 ]--- <6>[ 5.102124] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.110311] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.122326] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.130189] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.142383] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.151386] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.158694] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.169655] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.178920] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.186358] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.200236] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 5.213031] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.220753] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.232327] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.240232] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.252440] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.261359] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.268797] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 5.275741] hub 1-1:1.0: USB hub found <4>[ 5.279665] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.289116] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.296299] hub 1-1:1.0: 3 ports detected <6>[ 5.296659] panel-simple panel-lvds0: Dropping the link to regulator.0 <4>[ 5.300935] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 5.311388] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <4>[ 5.315247] GPT:29296874 != 30560255 <6>[ 5.322816] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <4>[ 5.326403] GPT:Alternate GPT header not at the end of the disk. <4>[ 5.326413] GPT:29296874 != 30560255 <4>[ 5.326425] GPT: Use GNU Parted to correct GPT errors. <6>[ 5.337820] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.339866] mmcblk0: p1 p2 p3 <6>[ 5.343846] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.372105] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.381017] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.388321] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.399136] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.408394] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.415739] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.426104] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.433716] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.445098] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.452803] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.464805] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.473697] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.480923] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 5.493611] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 5.501599] hctosys: unable to open rtc device (rtc0) <4>[ 5.512192] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.521521] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.529352] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.539867] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.547430] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.559007] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.566651] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.578776] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.587623] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.594843] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 5.630771] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 5.647379] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 8.810062] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 8.838132] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.867769] Sending DHCP requests ., OK <6>[ 8.912360] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.11 <6>[ 8.920858] IP-Config: Complete: <6>[ 8.924409] device=eth0, hwaddr=00:19:b8:07:40:03, ipaddr=192.168.201.11, mask=255.255.255.0, gw=192.168.201.1 <6>[ 8.935275] host=imx6q-sabrelite-lava-cbg-0, domain=lava-rack, nis-domain=(none) <6>[ 8.943519] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 8.943534] nameserver0=192.168.201.1 <6>[ 9.012816] Freeing unused kernel memory: 2048K <6>[ 9.018767] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 9.357442] udevd[109]: starting version 3.2.9 <5>[ 9.365504] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 9.374090] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 9.381215] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 9.399523] udevd[109]: specified user 'tss' unknown <27>[ 9.405059] udevd[109]: specified group 'tss' unknown <30>[ 9.416704] udevd[110]: starting eudev-3.2.9 <4>[ 10.341891] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 10.351327] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 10.374464] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 10.386005] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 10.393970] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 10.407244] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 10.407344] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 10.426888] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 10.448966] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 10.450404] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <4>[ 10.461348] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 10.471919] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 10.480642] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 10.485435] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <4>[ 10.492422] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 10.504342] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 10.512797] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 10.521669] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 10.523680] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 10.528628] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 10.542660] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 10.554484] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 10.562219] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 10.594854] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 10.620530] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 10.626924] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 10.647900] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 1 <4>[ 10.659593] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 10.668751] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 10.680354] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 10.687489] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 10.694202] sgtl5000 0-000a: Linked as a consumer to regulator.8 <4>[ 10.701814] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 10.711384] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 10.719268] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 10.719523] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 10.735460] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 10.743736] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 10.755956] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 10.764462] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 10.772217] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 10.777549] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 10.789179] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 10.797117] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 10.868296] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 10.877533] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 10.886122] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 10.897831] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 10.906428] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 10.918585] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 10.926513] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 10.939275] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 10.948267] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 10.955547] panel-simple panel-lcd: Dropping the link to regulator.0 done Saving random seed: <5>[ 11.390801] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 11.632763] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11637462/environment . /lava-11637462/environment / # /lava-11637462/bin/lava-test-runner /lava-11637462/0 /lava-11637462/bin/lava-test-runner /lava-11637462/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-11637462/0/tests/0_dmesg + cat uuid + UUID=11637462_1.5.2.4.1 <8>[ 12.376791] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 12.488117] <8>[ 12.582996] <8>[ 12.677152] + set +x <8>[ 12.688807] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11637462/environment / # . /lava-11637462/environment/lava-11637462/bin/lava-test-runner /lava-11637462/1 / # /lava-11637462/bin/lava-test-runner /lava-11637462/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-11637462/1/tests/1_bootrr + cat uuid + UUID=11637462_1.5.2.4.5<8>[ 13.307808] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11637462/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds panel-lcd /lava-11637462/1/../bin/lava-test-case <8>[ 14.473903] /lava-11637462/1/../bin/lava-test-case <8>[ 14.574736] /lava-11637462/1/../bin/lava-test-case <8>[ 14.631269] + set +x <8>[ 14.668105] / #