[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Error selecting device Error selecting device Error selecting device Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (4 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11637457/tftp-deploy-h20f0q9m/kernel/zImage tftp 0x10000000 11637457/tftp-deploy-h20f0q9m/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '11637457/tftp-deploy-h20f0q9m/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 14.2 MiB/s done Bytes transferred = 10433024 (9f3200 hex) => tftp 0x14000000 11637457/tftp-deploy-h20f0q9m/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11637457/tftp-deploy-h20f0q9m/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '11637457/tftp-deploy-h20f0q9m/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 14.1 MiB/s done Bytes transferred = 11427756 (ae5fac hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11637457/tftp-deploy-h20f0q9m/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11637457/tftp-deploy-h20f0q9m/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '11637457/tftp-deploy-h20f0q9m/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5 MiB/s done Bytes transferred = 41818 (a35a hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11637457/extract-nfsrootfs-udzz2s1o,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11637457/extract-nfsrootfs-udzz2s1o,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x9f3200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 11427692 Bytes = 10.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d359 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.295-cip103 (KernelCI@build-j60818-arm-gcc-10-multi-v7-defconfig-kselftest-s2kwm) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Thu Sep 28 23:50:18 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s40104 r8192 d21336 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11637457/extract-nfsrootfs-udzz2s1o,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 928380K/1048576K available (15360K kernel code, 1762K rwdata, 6316K rodata, 2048K init, 7700K bss, 54660K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (16352 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1763 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7701 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 49070 entries in 192 pages <6>[ 0.000000] ftrace: allocated 192 pages with 2 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022001] Console: colour dummy device 80x30 <4>[ 0.023888] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.031914] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.036258] ... MAX_LOCK_DEPTH: 48 <4>[ 0.040665] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.045276] ... CLASSHASH_SIZE: 4096 <4>[ 0.049916] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.054584] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.059310] ... CHAINHASH_SIZE: 32768 <4>[ 0.063981] memory used by lock dependency info: 4655 kB <4>[ 0.069664] per task-struct memory footprint: 1536 bytes <6>[ 0.075342] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.085766] CPU: Testing write buffer coherency: ok <6>[ 0.090868] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.096207] pid_max: default: 32768 minimum: 301 <6>[ 0.101359] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.107972] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.118061] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.123371] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.130244] rcu: Hierarchical SRCU implementation. <6>[ 0.137378] EFI services will not be available. <6>[ 0.140268] smp: Bringing up secondary CPUs ... <6>[ 0.146514] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.146527] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.158125] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.158137] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.169030] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.169042] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.178256] smp: Brought up 1 node, 4 CPUs <6>[ 0.182142] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.188663] CPU: All CPU(s) started in SVC mode. <6>[ 0.196187] devtmpfs: initialized <6>[ 0.231510] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.239173] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.246848] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.257135] pinctrl core: initialized pinctrl subsystem <6>[ 0.264733] DMI not present or invalid. <6>[ 0.267982] NET: Registered protocol family 16 <6>[ 0.279215] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.289882] cpuidle: using governor menu <6>[ 0.291712] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.331577] vdd1p1: supplied by regulator-dummy <6>[ 0.335523] vdd3p0: supplied by regulator-dummy <6>[ 0.340140] vdd2p5: supplied by regulator-dummy <6>[ 0.344875] vddarm: supplied by regulator-dummy <6>[ 0.350364] vddpu: supplied by regulator-dummy <6>[ 0.353912] vddsoc: supplied by regulator-dummy <6>[ 0.406035] No ATAGs? <6>[ 0.406522] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.414522] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.431920] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.439934] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.463889] Serial: AMBA PL011 UART driver <6>[ 0.563527] mxs-dma 110000.dma-apbh: initialized <6>[ 0.589536] vgaarb: loaded <5>[ 0.592541] SCSI subsystem initialized <6>[ 0.595096] usbcore: registered new interface driver usbfs <6>[ 0.599729] usbcore: registered new interface driver hub <6>[ 0.605162] usbcore: registered new device driver usb <6>[ 0.614975] i2c i2c-0: IMX I2C adapter registered <6>[ 0.617183] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.624524] i2c i2c-1: IMX I2C adapter registered <6>[ 0.627705] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.634482] i2c i2c-2: IMX I2C adapter registered <6>[ 0.638228] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.647788] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.650178] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.659671] PTP clock support registered <6>[ 0.664556] EDAC MC: Ver: 3.0.0 <6>[ 0.678167] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.940719] NET: Registered protocol family 2 <6>[ 0.943156] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.951772] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 20480 bytes) <6>[ 0.957584] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.965057] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) <6>[ 0.972897] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.978772] UDP hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.984554] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.991677] NET: Registered protocol family 1 <6>[ 0.997472] RPC: Registered named UNIX socket transport module. <6>[ 1.001840] RPC: Registered udp transport module. <6>[ 1.006709] RPC: Registered tcp transport module. <6>[ 1.011726] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.020329] Trying to unpack rootfs image as initramfs... <6>[ 2.211079] Freeing initrd memory: 11160K <4>[ 2.213497] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 2.221013] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 2.235836] Initialise system trusted keyrings <6>[ 2.238692] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.272258] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.278247] NFS: Registering the id_resolver key type <5>[ 2.280922] Key type id_resolver registered <5>[ 2.285276] Key type id_legacy registered <6>[ 2.289790] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.301759] Key type asymmetric registered <5>[ 2.303364] Asymmetric key parser 'x509' registered <6>[ 2.308764] bounce: pool size: 64 pages <6>[ 2.312693] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 2.320266] io scheduler noop registered <6>[ 2.324341] io scheduler deadline registered <6>[ 2.329374] io scheduler cfq registered (default) <6>[ 2.333825] io scheduler mq-deadline registered <6>[ 2.338658] io scheduler kyber registered <4>[ 2.343456] test_firmware: interface ready <6>[ 2.422334] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.427373] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.434821] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.441841] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.493386] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 2.497068] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 2.504779] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 2.511160] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 2.519126] PU : no governor for states <6>[ 2.522705] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <4>[ 2.554478] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 2.561670] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 2.745221] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.761455] SuperH (H)SCI(F) driver initialized <6>[ 2.765579] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 2.775071] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 2.784235] console [ttymxc1] enabled <6>[ 2.784235] console [ttymxc1] enabled <6>[ 2.789337] bootconsole [ec_imx21] disabled <6>[ 2.789337] bootconsole [ec_imx21] disabled <6>[ 2.802143] msm_serial: driver initialized <6>[ 2.807346] STMicroelectronics ASC driver initialized <6>[ 2.817854] STM32 USART driver initialized <6>[ 2.837705] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 2.862350] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.871315] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.878637] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.885657] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.894946] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.902526] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.938676] brd: module loaded <6>[ 2.970646] loop: module loaded <6>[ 2.983778] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.992045] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.000398] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.008908] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 3.020230] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.027508] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.036692] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.049969] scsi host0: ahci-imx <6>[ 3.055273] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 3.099725] CAN device driver interface <6>[ 3.107243] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 3.116205] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 3.125425] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 3.135608] pps pps0: new PPS source ptp0 <6>[ 3.173938] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.183336] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 3.189518] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.195892] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 3.203188] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.225944] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.233813] usbcore: registered new interface driver pegasus <6>[ 3.239968] usbcore: registered new interface driver asix <6>[ 3.245757] usbcore: registered new interface driver ax88179_178a <6>[ 3.252287] usbcore: registered new interface driver cdc_ether <6>[ 3.258599] usbcore: registered new interface driver smsc75xx <6>[ 3.264805] usbcore: registered new interface driver smsc95xx <6>[ 3.270985] usbcore: registered new interface driver net1080 <6>[ 3.277029] usbcore: registered new interface driver cdc_subset <6>[ 3.283412] usbcore: registered new interface driver zaurus <6>[ 3.289753] usbcore: registered new interface driver cdc_ncm <6>[ 3.304241] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.311110] ehci-pci: EHCI PCI platform driver <6>[ 3.315952] ehci-platform: EHCI generic platform driver <6>[ 3.322312] ehci-orion: EHCI orion driver <6>[ 3.327315] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.332334] ehci-st: EHCI STMicroelectronics driver <6>[ 3.338214] ehci-exynos: EHCI EXYNOS driver <6>[ 3.343336] ehci-atmel: EHCI Atmel driver <6>[ 3.348330] tegra-ehci: Tegra EHCI driver <6>[ 3.353321] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.359889] ohci-pci: OHCI PCI platform driver <6>[ 3.364732] ohci-platform: OHCI generic platform driver <6>[ 3.371052] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.376015] ohci-st: OHCI STMicroelectronics driver <6>[ 3.381907] ohci-atmel: OHCI Atmel driver <6>[ 3.388934] usbcore: registered new interface driver usb-storage <6>[ 3.390682] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.401079] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.401577] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 3.407631] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.424460] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 3.436296] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.441747] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.478137] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.487726] hub 1-0:1.0: USB hub found <6>[ 3.492177] hub 1-0:1.0: 1 port detected <6>[ 3.518820] i2c /dev entries driver <6>[ 3.570311] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 3.591742] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.598269] sdhci: Copyright(c) Pierre Ossman <6>[ 3.609192] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.621411] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.629421] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 3.634942] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 3.640883] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 3.684635] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 3.693320] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 3.699247] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 3.738775] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 3.757987] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.767250] usbcore: registered new interface driver usbhid <6>[ 3.773193] usbhid: USB HID core driver <6>[ 3.794536] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.801986] IPv4 over IPsec tunneling driver <6>[ 3.810100] NET: Registered protocol family 10 <6>[ 3.816563] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 3.825370] Segment Routing with IPv6 <6>[ 3.831893] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.835542] mmc0: new high speed SDHC card at address 0001 <6>[ 3.842127] NET: Registered protocol family 17 <6>[ 3.848590] mmcblk0: mmc0:0001 SD 14.8 GiB (ro) <6>[ 3.849136] can: controller area network core (rev 20170425 abi 9) <6>[ 3.858573] mmcblk0: p1 <6>[ 3.860325] NET: Registered protocol family 29 <6>[ 3.867641] can: raw protocol (rev 20170425) <6>[ 3.872344] can: broadcast manager protocol (rev 20170425 t) <6>[ 3.878374] can: netlink gateway (rev 20170425) max_hops=1 <6>[ 3.884899] 8021q: 802.1Q VLAN Support v1.8 <5>[ 3.890193] Key type dns_resolver registered <6>[ 3.905655] cpu cpu0: Linked as a consumer to regulator.4 <4>[ 3.911445] ------------[ cut here ]------------ <6>[ 3.911672] cpu cpu0: Linked as a consumer to regulator.5 <4>[ 3.916348] WARNING: CPU: 0 PID: 0 at include/trace/events/lock.h:13 lock_acquire+0x138/0x1f0 <4>[ 3.916356] Modules linked in: <6>[ 3.922416] cpu cpu0: Linked as a consumer to regulator.6 <4>[ 3.930808] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.295-cip103 #1 <4>[ 3.930814] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 3.930820] Backtrace: <4>[ 3.930840] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 3.930850] r7:ffffffff r6:00000000 r5:60000093 r4:c1c9d72c <4>[ 3.930871] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 3.938107] ------------[ cut here ]------------ <6>[ 3.938732] ThumbEE CPU extension supported. <5>[ 3.938771] Registering SWP/SWPB emulation handler <4>[ 3.939851] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <4>[ 3.946834] WARNING: CPU: 1 PID: 0 at include/trace/events/lock.h:58 lock_release+0x364/0x370 <4>[ 3.953608] r9:60000093 r8:c1b084bc r7:00000000 r6:00000009 r5:00000000 r4:00000000 <4>[ 3.956316] Modules linked in: <4>[ 3.964168] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 4.028424] r6:c03b8c74 r5:0000000d r4:c1681ef4 <4>[ 4.033335] [] (warn_slowpath_null) from [] (lock_acquire+0x138/0x1f0) <4>[ 4.041880] r6:00000000 r5:00000000 r4:c1b05990 <4>[ 4.046799] [] (lock_acquire) from [] (_raw_spin_lock+0x58/0x68) <4>[ 4.054832] r10:ef79a2f8 r9:ef79a2f8 r8:00000001 r7:ef79e740 r6:00000001 r5:c23e9aec <4>[ 4.062939] r4:c1b05980 <4>[ 4.065772] [] (_raw_spin_lock) from [] (__tick_broadcast_oneshot_control+0x4c/0x2ac) <4>[ 4.075618] r4:c1b01e88 <4>[ 4.078443] [] (__tick_broadcast_oneshot_control) from [] (tick_broadcast_oneshot_control+0x3c/0x40) <4>[ 4.089599] r9:ef79a2f8 r8:00000001 r7:c1b10e94 r6:c1b10ea4 r5:c1b10e44 r4:00000001 <4>[ 4.097635] [] (tick_broadcast_oneshot_control) from [] (cpuidle_enter_state+0x50/0x520) <4>[ 4.107754] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 4.116306] r10:ef79a2f8 r9:c1b10e44 r8:c1aa22f0 r7:c1b08500 r6:c1b10e44 r5:ef79a2f8 <4>[ 4.124414] r4:00000001 <4>[ 4.127251] [] (cpuidle_enter) from [] (do_idle+0x20c/0x2f8) <4>[ 4.134932] r7:c1b08500 r6:c1b084bc r5:00000000 r4:c1b00000 <4>[ 4.140885] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 4.148742] r10:c19e4a50 r9:00000001 r8:efffe8c0 r7:c1b08480 r6:00000002 r5:c1b01f78 <4>[ 4.156849] r4:000000ca <4>[ 4.159675] [] (cpu_startup_entry) from [] (rest_init+0x2c8/0x2e0) <4>[ 4.167890] [] (rest_init) from [] (start_kernel+0x468/0x4a4) <4>[ 4.175654] r6:ffffffff r5:00000001 r4:c1cb9058 <4>[ 4.180557] [] (start_kernel) from [<00000000>] ( (null)) <4>[ 4.187199] r10:10c5387d r9:412fc09a r8:13f00000 r7:00000eb9 r6:10c0387d r5:00000051 <4>[ 4.195305] r4:c19004b0 <4>[ 4.198117] irq event stamp: 7764 <4>[ 4.198129] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.19.295-cip103 #1 <4>[ 4.198142] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 4.201744] hardirqs last enabled at (7763): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 4.208689] Backtrace: <4>[ 4.215501] hardirqs last disabled at (7764): [] do_idle+0xb0/0x2f8 <4>[ 4.224554] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 4.227264] softirqs last enabled at (7756): [] __do_softirq+0x344/0x520 <4>[ 4.234657] r7:ffffffff r6:00000000 r5:60000093 r4:c1c9d72c <4>[ 4.242508] softirqs last disabled at (7743): [] irq_exit+0x170/0x1c8 <4>[ 4.250429] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 4.256335] ---[ end trace 591caa272618a51d ]--- <4>[ 4.263923] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <4>[ 4.284120] r9:c03ff720 r8:00000001 r7:60000093 r6:00000009 r5:00000000 r4:00000000 <4>[ 4.292155] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 4.300615] r6:c03b8b30 r5:0000003a r4:c1681ef4 <4>[ 4.305525] [] (warn_slowpath_null) from [] (lock_release+0x364/0x370) <4>[ 4.314071] r6:c1b456c4 r5:c1b456c4 r4:c1b084bc <4>[ 4.318983] [] (lock_release) from [] (ktime_get+0x84/0x1ac) <4>[ 4.326666] r10:00000001 r9:60000093 r8:00000001 r7:c1b45700 r6:c1b456c4 r5:c03ff720 <4>[ 4.334772] r4:c1b45600 <4>[ 4.337596] [] (ktime_get) from [] (clockevents_program_event+0x6c/0x184) <4>[ 4.346409] r10:ef7ab2f8 r9:c23e9b00 r8:00000001 r7:ea3f0a80 r6:00000000 r5:00000001 <4>[ 4.354514] r4:ee829c40 <4>[ 4.357339] [] (clockevents_program_event) from [] (tick_broadcast_set_event+0x54/0xb4) <4>[ 4.367361] r7:ea3f0a80 r6:00000000 r5:00000001 r4:ee829c40 <4>[ 4.373311] [] (tick_broadcast_set_event) from [] (__tick_broadcast_oneshot_control+0x140/0x2ac) <4>[ 4.384116] r7:ef7af740 r6:ee829c40 r5:00000000 r4:00000001 <4>[ 4.390065] [] (__tick_broadcast_oneshot_control) from [] (tick_broadcast_oneshot_control+0x3c/0x40) <4>[ 4.401220] r9:ef7ab2f8 r8:00000001 r7:c1b10e94 r6:c1b10ea4 r5:c1b10e44 r4:00000001 <4>[ 4.409254] [] (tick_broadcast_oneshot_control) from [] (cpuidle_enter_state+0x50/0x520) <4>[ 4.419368] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 4.427920] r10:ef7ab2f8 r9:c1b10e44 r8:c1aa22f0 r7:c1b08500 r6:c1b10e44 r5:ef7ab2f8 <4>[ 4.436025] r4:00000001 <4>[ 4.438852] [] (cpuidle_enter) from [] (do_idle+0x20c/0x2f8) <4>[ 4.446530] r7:c1b08500 r6:c1b084bc r5:00000001 r4:ee9d6000 <4>[ 4.452483] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 4.460339] r10:00000000 r9:412fc09a r8:1020406a r7:c1cb9650 r6:00000001 r5:ee9d6000 <4>[ 4.468445] r4:00000089 <4>[ 4.471278] [] (cpu_startup_entry) from [] (secondary_start_kernel+0x170/0x17c) <4>[ 4.480617] [] (secondary_start_kernel) from [<1030312c>] (0x1030312c) <4>[ 4.488296] r7:c1cb9650 r6:10c0387d r5:00000051 r4:3e9c406a <4>[ 4.494233] irq event stamp: 17400 <4>[ 4.497927] hardirqs last enabled at (17399): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 4.507087] hardirqs last disabled at (17400): [] do_idle+0xb0/0x2f8 <4>[ 4.514595] softirqs last enabled at (17392): [] __do_softirq+0x344/0x520 <4>[ 4.522627] softirqs last disabled at (17381): [] irq_exit+0x170/0x1c8 <4>[ 4.530300] ---[ end trace 591caa272618a51e ]--- <5>[ 4.538878] Loading compiled-in X.509 certificates <6>[ 4.581124] hub 1-1:1.0: USB hub found <6>[ 4.585574] hub 1-1:1.0: 3 ports detected <6>[ 4.622267] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.630225] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 4.642144] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 4.649851] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.662000] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 4.671059] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 4.678287] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 4.689094] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 4.698337] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 4.705675] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 4.719490] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 4.732118] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.739763] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 4.751211] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 4.758931] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.770966] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 4.779858] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 4.787023] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 4.797768] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 4.807017] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 4.814400] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 4.825094] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.832727] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 4.844276] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 4.851973] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.863970] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 4.872857] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 4.880073] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 4.890818] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 4.900057] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 4.907390] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 4.920380] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 4.928451] hctosys: unable to open rtc device (rtc0) <6>[ 4.938404] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.946053] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 4.957599] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 4.965501] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.977618] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 4.986515] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 4.993729] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.004499] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.013735] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.021117] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.061054] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 5.077563] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 8.170256] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 8.198877] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.228145] Sending DHCP requests ., OK <6>[ 8.272636] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 <6>[ 8.281137] IP-Config: Complete: <6>[ 8.284688] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 <6>[ 8.295560] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) <6>[ 8.303800] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 8.303814] nameserver0=192.168.201.1 <6>[ 8.373303] Freeing unused kernel memory: 2048K <6>[ 8.379232] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 11.220265] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 11.231988] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.240157] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.249458] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 11.251979] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.271954] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 11.284471] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.293468] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.299641] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.300779] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 11.319014] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.328311] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.330915] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.335694] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 11.352895] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.360755] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.368449] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.372524] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.375282] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 11.383103] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 11.455736] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 11.489655] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 11.496083] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <4>[ 11.506509] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.507087] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 1 <6>[ 11.515455] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.530161] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 11.538614] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 11.545265] sgtl5000 0-000a: Linked as a consumer to regulator.8 <4>[ 11.551872] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.561164] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.563361] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 11.568863] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 11.584159] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.590059] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 11.591898] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.611293] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.619068] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 11.631540] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.640535] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.647756] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 11.677438] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.686793] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.699843] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 11.710620] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.719589] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.731354] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.739171] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 11.751596] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.760539] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.767733] panel-simple panel-lcd: Dropping the link to regulator.0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:10 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.34 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-4 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 13.687928] systemd[1]: System time before build time, advancing clock. <3>[ 13.990926] cgroup: cgroup2: unknown option "memory_recursiveprot" <30>[ 14.030214] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 14.056204] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 14.103200] systemd[1]: Set hostname to . <30>[ 15.451299] systemd[1]: Queued start job for default target Graphical Interface. <5>[ 15.461513] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 15.471766] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <5>[ 15.508568] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 15.517304] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <5>[ 15.558998] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 15.569367] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 15.609969] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 15.652857] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 15.701272] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 15.750139] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 15.763355] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 15.809730] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 15.849823] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 15.888604] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 15.929334] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 15.972345] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 16.075258] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 16.087388] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 16.134121] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 16.183995] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 16.238268] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 16.282987] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 16.331692] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 16.342249] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 16.361132] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 16.416579] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 16.468913] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <5>[ 16.509201] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 16.523946] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <5>[ 16.559279] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 16.574018] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <5>[ 16.609294] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 16.626390] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 16.652802] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 16.680362] systemd[1]: Starting Journal Service... Starting Journal Service... <6>[ 16.696516] fuse init (API version 7.27) <30>[ 16.733121] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 16.776469] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 16.825782] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 16.882784] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 16.921328] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 16.966068] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 17.044796] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 17.054672] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 17.104594] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 17.113530] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. <30>[ 17.154143] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 17.163234] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. <30>[ 17.203203] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. <30>[ 17.243184] systemd[1]: Finished Remount Root and Kernel File Systems. [ OK ] Finished Remount Root and Kernel File Systems. <30>[ 17.299525] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... <30>[ 17.345399] systemd[1]: Mounting Kernel Configuration File System... Mounting Kernel Configuration File System... <30>[ 17.385926] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. <30>[ 17.396303] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. <30>[ 17.414388] systemd[1]: Starting Load/Save Random Seed... Starting Load/Save Random Seed... <30>[ 17.455244] systemd[1]: Starting Apply Kernel Variables... Starting Apply Kernel Variables... <30>[ 17.496524] systemd[1]: Starting Create System Users... Starting Create System Users... <30>[ 17.517107] systemd[1]: Started Journal Service. <5>[ 17.524310] random: systemd-journal: uninitialized urandom read (16 bytes read) [ OK ] Started Journal Service. [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. <5>[ 17.702493] random: systemd: uninitialized urandom read (16 bytes read) <5>[ 17.726527] random: systemd-journal: uninitialized urandom read (16 bytes read) Starting Flush Journal to Persistent Storage... [ OK ] Finished Create System Users. <46>[ 17.820335] systemd-journald[164]: Received client request to flush runtime journal. Starting Create Static Device Nodes in /dev... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Rule-based Manage…for Device Events and Files... <5>[ 18.969423] random: crng init done <5>[ 18.973259] random: 45 urandom warning(s) missed due to ratelimiting [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.295-cip103 #1 SMP Thu Sep 28 23:50:18 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11637457/extract-nfsrootfs-udzz2s1o' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11637457/extract-nfsrootfs-udzz2s1o' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-11637457/environment . /lava-11637457/environment / # /lava-11637457/bin/lava-test-runner /lava-11637457/0 /lava-11637457/bin/lava-test-runner /lava-11637457/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-11637457/0/tests/0_timesync-off ++ cat uuid + UUID=11637457_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x <6>[ 38.899543] usb_otg_vbus: disabling <6>[ 38.903497] CAN XCVR: disabling + export TESTRUN_ID=1_kselftest-lkdtm + TESTRUN_ID=1_kselftest-lkdtm + cd /lava-11637457/0/tests/1_kselftest-lkdtm ++ cat uuid + UUID=11637457_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c lkdtm -T '' -t kselftest_armhf.tar.gz -s True -u None -L '' -S /dev/null -b imx6q-sabrelite -g cip -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-09-29 00:04:43-- http://none/ Resolving none (none)... failed: Name or service not known. wget: unable to resolve host address 'none' tar: None: Cannot open: No such file or directory tar: Error is not recoverable: exiting now ./kselftest.sh: 160: cd: can't cd to kselftest / #