Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot 2019.04-lf-5.4.y_v2019.04+g228843cdf5 (Feb 24 2020 - 11:58:52 +0000) CPU: Freescale i.MX6UL rev1.2 696 MHz (running at 396 MHz) CPU: Automotive temperature grade (-40C to 125C) at 32C Reset cause: POR Model: Freescale i.MX6 UltraLite 14x14 EVK Board Board: MX6UL 14x14 EVK DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc1 is current device flash target is MMC:1 Net: Warning: ethernet@020b4000 using MAC address from ROM eth1: ethernet@020b4000 [PRIME] Warning: ethernet@02188000 using MAC address from ROM , eth0: ethernet@02188000 Fastboot: Normal Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.212 (1298 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp ${loadaddr} 1253282/tftp-deploy-9d3lme5j/kernel/zImage tftp ${loadaddr} 1253282/tftp-deploy-9d3lme5j/kernel/zImage Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.212; sending through gateway 172.16.1.4 Filename '1253282/tftp-deploy-9d3lme5j/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 4.9 MiB/s done Bytes transferred = 8733184 (854200 hex) => tftp ${initrd_addr} 1253282/tftp-deploy-9d3lme5j/ramdisk/ramdisk.cpio.gz.uboot tftp ${initrd_addr} 1253282/tftp-deploy-9d3lme5j/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.212; sending through gateway 172.16.1.4 Filename '1253282/tftp-deploy-9d3lme5j/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# 4.9 MiB/s done Bytes transferred = 13344267 (cb9e0b hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp ${fdt_addr} 1253282/tftp-deploy-9d3lme5j/dtb/imx6ul-14x14-evk.dtb tftp ${fdt_addr} 1253282/tftp-deploy-9d3lme5j/dtb/imx6ul-14x14-evk.dtb Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.212; sending through gateway 172.16.1.4 Filename '1253282/tftp-deploy-9d3lme5j/dtb/imx6ul-14x14-evk.dtb'. Load address: 0x83000000 Loading: *## 3.3 MiB/s done Bytes transferred = 27998 (6d5e hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz ${loadaddr} ${initrd_addr} ${fdt_addr} bootz ${loadaddr} ${initrd_addr} ${fdt_addr} Kernel image @ 0x80800000 [ 0x000000 - 0x854200 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13344203 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 83009d5d ft_system_setup for mx6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.295-cip103 (KernelCI@build-j60840-arm-gcc-10-multi-v7-defconfig-556x5) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Thu Sep 28 23:52:00 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 UltraLite 14x14 EVK Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x02020000 (options '') [ 0.000000] bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) <6>[ 0.000000] Memory: 419456K/524288K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 39296K reserved, 65536K cma-reserved, 0K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] Switching to timer-based delay loop, resolution 41ns <6>[ 0.000018] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008102] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.023357] Console: colour dummy device 80x30 <6>[ 0.025294] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.035921] CPU: Testing write buffer coherency: ok <6>[ 0.040977] pid_max: default: 32768 minimum: 301 <6>[ 0.046182] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.052731] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) <3>[ 0.061966] /cpus/cpu@0 missing clock-frequency property <6>[ 0.065607] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.073291] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.080599] rcu: Hierarchical SRCU implementation. <6>[ 0.088417] EFI services will not be available. <6>[ 0.090834] smp: Bringing up secondary CPUs ... <6>[ 0.095255] smp: Brought up 1 node, 1 CPU <6>[ 0.099430] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.105899] CPU: All CPU(s) started in SVC mode. <6>[ 0.112460] devtmpfs: initialized <6>[ 0.126468] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.132203] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.141802] futex hash table entries: 256 (order: 2, 16384 bytes) <6>[ 0.152991] pinctrl core: initialized pinctrl subsystem <6>[ 0.159089] DMI not present or invalid. <6>[ 0.162536] NET: Registered protocol family 16 <6>[ 0.169383] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.178789] cpuidle: using governor menu <6>[ 0.197807] vdd3p0: supplied by regulator-dummy <6>[ 0.200754] cpu: supplied by regulator-dummy <6>[ 0.205762] vddsoc: supplied by regulator-dummy <6>[ 0.234052] No ATAGs? <6>[ 0.234197] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.242248] hw-breakpoint: maximum watchpoint size is 8 bytes. <4>[ 0.254645] imx6ul-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e4000 debugfs directory <6>[ 0.261901] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.276269] Serial: AMBA PL011 UART driver <6>[ 0.331236] mxs-dma 1804000.dma-apbh: initialized <6>[ 0.343923] vgaarb: loaded <5>[ 0.346083] SCSI subsystem initialized <6>[ 0.349365] usbcore: registered new interface driver usbfs <6>[ 0.353905] usbcore: registered new interface driver hub <6>[ 0.359532] usbcore: registered new device driver usb <6>[ 0.367464] i2c i2c-0: IMX I2C adapter registered <6>[ 0.369782] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.376677] i2c i2c-1: IMX I2C adapter registered <6>[ 0.380279] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.388692] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.391179] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.400529] PTP clock support registered <6>[ 0.405181] EDAC MC: Ver: 3.0.0 <6>[ 0.414687] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.550724] NET: Registered protocol family 2 <6>[ 0.553015] IP idents hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.560921] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.567365] TCP established hash table entries: 4096 (order: 2, 16384 bytes) <6>[ 0.574608] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) <6>[ 0.581359] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.588069] UDP hash table entries: 256 (order: 1, 8192 bytes) <6>[ 0.593960] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) <6>[ 0.600881] NET: Registered protocol family 1 <6>[ 0.606636] RPC: Registered named UNIX socket transport module. <6>[ 0.611233] RPC: Registered udp transport module. <6>[ 0.616333] RPC: Registered tcp transport module. <6>[ 0.621151] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.628928] Trying to unpack rootfs image as initramfs... <6>[ 3.082431] Freeing initrd memory: 13032K <5>[ 3.087808] Initialise system trusted keyrings <6>[ 3.090625] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 3.113614] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.118869] NFS: Registering the id_resolver key type <5>[ 3.122286] Key type id_resolver registered <5>[ 3.126737] Key type id_legacy registered <6>[ 3.130998] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.141206] Key type asymmetric registered <5>[ 3.142737] Asymmetric key parser 'x509' registered <6>[ 3.148136] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.155594] io scheduler noop registered <6>[ 3.159699] io scheduler deadline registered <6>[ 3.164694] io scheduler cfq registered (default) <6>[ 3.169185] io scheduler mq-deadline registered <6>[ 3.173966] io scheduler kyber registered <4>[ 3.217479] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 3.225036] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 3.232710] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 3.278359] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.285391] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.421272] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.432860] SuperH (H)SCI(F) driverJ��ѥ���镑5 <6>[ 3.438022] console [ttymxc0] enabled <6>[ 3.438022] console [ttymxc0] enabled <6>[ 3.443019] bootconsole [ec_imx6q0] disabled <6>[ 3.443019] bootconsole [ec_imx6q0] disabled <6>[ 3.454292] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 61, base_baud = 5000000) is a IMX <6>[ 3.466692] msm_serial: driver initialized <6>[ 3.471578] STMicroelectronics ASC driver initialized <6>[ 3.480325] STM32 USART driver initialized <4>[ 3.505039] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 3.513123] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 3.519935] panel-simple panel: Dropping the link to regulator.0 <6>[ 3.549504] brd: module loaded <6>[ 3.567053] loop: module loaded <6>[ 3.598400] CAN device driver interface <6>[ 3.605152] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 3.613075] fec 20b4000.ethernet: 20b4000.ethernet supply phy not found, using dummy regulator <6>[ 3.622239] fec 20b4000.ethernet: Linked as a consumer to regulator.0 <6>[ 3.629861] pps pps0: new PPS source ptp0 <6>[ 3.744411] fec 20b4000.ethernet eth0: registered PHC device 0 <4>[ 3.752499] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 3.761714] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 3.769358] pps pps1: new PPS source ptp1 <6>[ 5.464325] fec 2188000.ethernet eth1: registered PHC device 1 <6>[ 5.472959] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 5.479186] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 5.485583] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 5.492826] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 5.510120] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 5.518070] usbcore: registered new interface driver pegasus <6>[ 5.524127] usbcore: registered new interface driver asix <6>[ 5.529967] usbcore: registered new interface driver ax88179_178a <6>[ 5.536485] usbcore: registered new interface driver cdc_ether <6>[ 5.542709] usbcore: registered new interface driver smsc75xx <6>[ 5.548918] usbcore: registered new interface driver smsc95xx <6>[ 5.555086] usbcore: registered new interface driver net1080 <6>[ 5.561108] usbcore: registered new interface driver cdc_subset <6>[ 5.567442] usbcore: registered new interface driver zaurus <6>[ 5.573508] usbcore: registered new interface driver cdc_ncm <6>[ 5.585518] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 5.592339] ehci-pci: EHCI PCI platform driver <6>[ 5.597279] ehci-platform: EHCI generic platform driver <6>[ 5.603447] ehci-orion: EHCI orion driver <6>[ 5.608292] SPEAr-ehci: EHCI SPEAr driver <6>[ 5.612958] ehci-st: EHCI STMicroelectronics driver <6>[ 5.618598] ehci-exynos: EHCI EXYNOS driver <6>[ 5.623429] ehci-atmel: EHCI Atmel driver <6>[ 5.628181] tegra-ehci: Tegra EHCI driver <6>[ 5.632894] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 5.639487] ohci-pci: OHCI PCI platform driver <6>[ 5.644379] ohci-platform: OHCI generic platform driver <6>[ 5.650543] SPEAr-ohci: OHCI SPEAr driver <6>[ 5.655324] ohci-st: OHCI STMicroelectronics driver <6>[ 5.660849] ohci-atmel: OHCI Atmel driver <6>[ 5.667364] usbcore: registered new interface driver usb-storage <4>[ 5.678134] imx_usb 2184000.usb: 2184000.usb supply vbus not found, using dummy regulator <6>[ 5.686884] imx_usb 2184000.usb: Linked as a consumer to regulator.0 <4>[ 5.701211] imx_usb 2184200.usb: 2184200.usb supply vbus not found, using dummy regulator <6>[ 5.709986] imx_usb 2184200.usb: Linked as a consumer to regulator.0 <6>[ 5.721506] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 5.726913] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 5.764713] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 5.772292] hub 1-0:1.0: USB hub found <6>[ 5.776616] hub 1-0:1.0: 1 port detected <6>[ 5.794200] i2c /dev entries driver <6>[ 5.830442] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 5.847739] sdhci: Secure Digital Host Controller Interface driver <6>[ 5.854208] sdhci: Copyright(c) Pierre Ossman <6>[ 5.863414] Synopsys Designware Multimedia Card Interface Driver <6>[ 5.873862] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 5.882474] sdhci-esdhc-imx 2190000.usdhc: Got CD GPIO <6>[ 5.888338] sdhci-esdhc-imx 2190000.usdhc: Linked as a consumer to regulator.4 <6>[ 5.929808] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA <6>[ 5.972268] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA <6>[ 5.987815] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 5.996576] usbcore: registered new interface driver usbhid <6>[ 6.002437] usbhid: USB HID core driver <6>[ 6.020130] NET: Registered protocol family 10 <6>[ 6.028323] Segment Routing with IPv6 <6>[ 6.032470] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 6.040275] NET: Registered protocol family 17 <6>[ 6.045143] can: controller area network core (rev 20170425 abi 9) <6>[ 6.051760] NET: Registered protocol family 29 <6>[ 6.056561] can: raw protocol (rev 20170425) <6>[ 6.061119] can: broadcast manager protocol (rev 20170425 t) <6>[ 6.067122] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 6.073913] Key type dns_resolver registered <6>[ 6.080773] cpu cpu0: Linked as a consumer to regulator.2 <6>[ 6.086793] cpu cpu0: Linked as a consumer to regulator.3 <6>[ 6.093683] ThumbEE CPU extension supported. <5>[ 6.098387] Registering SWP/SWPB emulation handler <5>[ 6.107605] Loading compiled-in X.509 certificates <4>[ 6.132786] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 6.143136] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 6.151095] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 6.161705] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 6.169839] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 6.176727] panel-simple panel: Dropping the link to regulator.0 <6>[ 6.187397] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 6.199270] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 6.209617] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 6.217659] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 6.228211] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 6.236345] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 6.244191] panel-simple panel: Dropping the link to regulator.0 <4>[ 6.252849] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 6.263222] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 6.271146] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 6.281685] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 6.289827] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 6.297670] panel-simple panel: Dropping the link to regulator.0 <6>[ 6.306259] hctosys: unable to open rtc device (rtc0) <4>[ 6.366530] mmc1: host does not support reading read-only switch, assuming write-enable <6>[ 6.388228] mmc1: new high speed SDHC card at address aaaa <6>[ 6.400359] mmcblk1: mmc1:aaaa SS16G 14.8 GiB <6>[ 6.416085] mmcblk1: p1 p2 <4>[ 6.421934] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 6.432297] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 6.440294] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 6.450826] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 6.458970] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 6.465839] panel-simple panel: Dropping the link to regulator.0 <6>[ 6.473699] Micrel KSZ8081 or KSZ8091 20b4000.ethernet-1:01: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=20b4000.ethernet-1:01, irq=POLL) <6>[ 6.488537] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 6.606282] Micrel KSZ8081 or KSZ8091 20b4000.ethernet-1:02: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=20b4000.ethernet-1:02, irq=POLL) <6>[ 6.621433] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready <6>[ 9.598800] fec 20b4000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 9.627515] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 9.657181] Sending DHCP requests .., OK <6>[ 12.901713] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.212 <6>[ 12.909759] IP-Config: Complete: <6>[ 12.913305] device=eth0, hwaddr=00:04:9f:05:20:41, ipaddr=172.16.1.212, mask=255.255.255.0, gw=172.16.1.4 <6>[ 12.923689] host=172.16.1.212, domain=example.org, nis-domain=(none) <6>[ 12.930843] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 12.930862] nameserver0=172.16.1.4 <6>[ 12.953546] Freeing unused kernel memory: 2048K <6>[ 12.967831] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 13.217430] udevd[116]: starting version 3.2.9 <5>[ 13.223846] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 13.231927] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 13.239149] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 13.260383] udevd[116]: specified user 'tss' unknown <27>[ 13.266287] udevd[116]: specified group 'tss' unknown <30>[ 13.277412] udevd[117]: starting eudev-3.2.9 <4>[ 15.141124] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 15.151490] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 15.276168] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 15.286862] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 15.294993] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 15.390341] panel-simple panel: Dropping the link to regulator.0 <6>[ 15.610029] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 15.617055] [drm] No driver support for vblank timestamp query. <3>[ 15.623398] mxsfb 21c8000.lcdif: Failed to create outputs <6>[ 15.637863] fsl-quadspi 21e0000.qspi: n25q256a (32768 Kbytes) <4>[ 15.686739] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 15.697139] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 15.778759] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 15.789408] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 15.797564] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 15.915774] panel-simple panel: Dropping the link to regulator.0 <6>[ 15.958762] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 15.965813] [drm] No driver support for vblank timestamp query. <3>[ 15.972161] mxsfb 21c8000.lcdif: Failed to create outputs <4>[ 16.036953] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 16.047338] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 16.113711] pwm-backlight backlight-display: Dropping the link to regulator.0 done Saving random seed: <5>[ 17.322513] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 17.453928] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1253282/environment . /lava-1253282/environment / # /lava-1253282/bin/lava-test-runner /lava-1253282/0 /lava-1253282/bin/lava-test-runner /lava-1253282/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1253282/0/tests/0_dmesg + cat uuid + UUID=1253282_1.5.2.4.1 <8>[ 23.313511] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 23.380294] <8>[ 23.441102] <8>[ 23.501943] + set +x<8>[ 23.513128] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1253282/environment / # . /lava-1253282/environment/lava-1253282/bin/lava-test-runner /lava-1253282/1 / # /lava-1253282/bin/lava-test-runner /lava-1253282/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1253282/1/tests/1_bootrr + cat uuid + UUID=1253282_1.5.2.4.5 <8>[ 29.265080] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1253282/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel sound 21c8000.lcdif backlight-display /lava-1253282/1/../bin/lava-test-case <8>[ 30.370692] /lava-1253282/1/../bin/lava-test-case <8>[ 30.428225] /lava-1253282/1/../bin/lava-test-case <8>[ 30.462315] + set +x<8>[ 30.488059] / #