Trying 192.168.56.184... Connected to conserv2. Escape character is '^]'. ser2net port telnet,3002 device serialdev, /dev/serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.1.2.4:1.0-port0, 115200n81, [] (Debian GNU/Linux) U-Boot SPL 2022.04-00708-g42a2d90cf5-dirty (Apr 13 2022 - 18:05:19 +0100) DRAM: 2048 MiB Trying to boot from MMC1 NOTICE: BL31: v2.6(release):v2.6-457-g510155aa7-dirty NOTICE: BL31: Built : 17:52:26, Apr 13 2022 NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689) NOTICE: BL31: Found U-Boot DTB at 0x2099638, model: Pine64+ U-Boot 2022.04-00708-g42a2d90cf5-dirty (Apr 13 2022 - 18:05:19 +0100) Allwinner Technology CPU: Allwinner A64 (SUN50I) Model: Pine64+ DRAM: 2 GiB sunxi_set_gate: (CLK#58) unhandled Core: 61 devices, 17 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0 Loading Environment from FAT... Unable to use mmc 0:1... U-Boot SPL 2022.04-00708-g42a2d90cf5-dirty (Apr 13 2022 - 18:05:19 +0100) DRAM: 2048 MiB Trying to boot from MMC1 NOTICE: BL31: v2.6(release):v2.6-457-g510155aa7-dirty NOTICE: BL31: Built : 17:52:26, Apr 13 2022 NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689) NOTICE: BL31: Found U-Boot DTB at 0x2099638, model: Pine64+ U-Boot 2022.04-00708-g42a2d90cf5-dirty (Apr 13 2022 - 18:05:19 +0100) Allwinner Technology CPU: Allwinner A64 (SUN50I) Model: Pine64+ DRAM: 2 GiB sunxi_set_gate: (CLK#58) unhandled Core: 61 devices, 17 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0 Loading Environment from FAT... ** Bad device specification mmc 0 ** U-Boot SPL 2022.04-00708-g42a2d90cf5-dirty (Apr 13 2022 - 18:05:19 +0100) DRAM: 2048 MiB Trying to boot from MMC1 NOTICE: BL31: v2.6(release):v2.6-457-g510155aa7-dirty NOTICE: BL31: Built : 17:52:26, Apr 13 2022 NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689) NOTICE: BL31: Found U-Boot DTB at 0x2099638, model: Pine64+ U-Boot 2022.04-00708-g42a2d90cf5-dirty (Apr 13 2022 - 18:05:19 +0100) Allwinner Technology CPU: Allwinner A64 (SUN50I) Model: Pine64+ DRAM: 2 GiB sunxi_set_gate: (CLK#58) unhandled Core: 61 devices, 17 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0 Loading Environment from FAT... Unable to use mmc 0:1... In: serial Out: serial Err: serial Net: phy interface10 eth0: ethernet@1c30000 starting USB... Bus usb@1c1a000: sunxi_set_gate: (CLK#11) unhandled USB EHCI 1.00 Bus usb@1c1a400: USB OHCI 1.0 Bus usb@1c1b000: USB EHCI 1.00 Bus usb@1c1b400: USB OHCI 1.0 scanning bus usb@1c1a000 for devices... 1 USB Device(s) found scanning bus usb@1c1a400 for devices... 1 USB Device(s) found scanning bus usb@1c1b000 for devices... 1 USB Device(s) found scanning bus usb@1c1b400 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp ethernet@1c30000 Waiting for PHY auto negotiation to complete........ done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 BOOTP broadcast 5 BOOTP broadcast 6 BOOTP broadcast 7 *** Unhandled DHCP Option in OFFER/ACK: 42 *** Unhandled DHCP Option in OFFER/ACK: 42 DHCP client bound to address 192.168.56.110 (8116 ms) => setenv serverip 192.168.56.76 setenv serverip 192.168.56.76 => tftp 0x40080000 319889/tftp-deploy-bd7y1cwc/kernel/Image tftp 0x40080000 319889/tftp-deploy-bd7y1cwc/kernel/Image Using ethernet@1c30000 device TFTP from server 192.168.56.76; our IP address is 192.168.56.110 Filename '319889/tftp-deploy-bd7y1cwc/kernel/Image'. Load address: 0x40080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################### 14.3 MiB/s done Bytes transferred = 25084416 (17ec200 hex) => tftp 0x4FF00000 319889/tftp-deploy-bd7y1cwc/ramdisk/ramdisk.cpio.gz.uboot tftp 0x4FF00000 319889/tftp-deploy-bd7y1cwc/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@1c30000 device TFTP from server 192.168.56.76; our IP address is 192.168.56.110 Filename '319889/tftp-deploy-bd7y1cwc/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x4ff00000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################################### 14.6 MiB/s done Bytes transferred = 16759577 (ffbb19 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x4FA00000 319889/tftp-deploy-bd7y1cwc/dtb/sun50i-a64-pine64-plus.dtb tftp 0x4FA00000 319889/tftp-deploy-bd7y1cwc/dtb/sun50i-a64-pine64-plus.dtb Using ethernet@1c30000 device TFTP from server 192.168.56.76; our IP address is 192.168.56.110 Filename '319889/tftp-deploy-bd7y1cwc/dtb/sun50i-a64-pine64-plus.dtb'. Load address: 0x4fa00000 Loading: *## 5.1 MiB/s done Bytes transferred = 16184 (3f38 hex) => setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x40080000 0x4FF00000 0x4FA00000 booti 0x40080000 0x4FF00000 0x4FA00000 ## Loading init Ramdisk from Legacy Image at 4ff00000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 16759513 Bytes = 16 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 4fa00000 Booting using the fdt blob at 0x4fa00000 Loading Device Tree to 0000000049ff9000, end 0000000049ffff37 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 4.19.299-cip105 (KernelCI@build-j38063-arm64-gcc-10-defconfig-kselftest-szxtw) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP PREEMPT Thu Dec 7 20:23:41 UTC 2023 [ 0.000000] Machine model: Pine64+ [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 32 MiB at 0x00000000be000000 [ 0.000000] earlycon: uart0 at MMIO32 0x0000000001c28000 (options '115200n8') [ 0.000000] bootconsole [uart0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] NUMA: NODE_DATA [mem 0xbdfda140-0xbdfdb9ff] [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 25 pages/cpu s65480 r8192 d28728 u102400 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 843419 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516096 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Memory: 1977616K/2097152K available (14652K kernel code, 2160K rwdata, 5744K rodata, 1920K init, 12349K bss, 86768K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 47006 entries in 184 pages <6>[ 0.000000] ftrace: allocated 184 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. <6>[ 0.000000] Tasks RCU enabled. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GIC: Using split EOI/Deactivate mode <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.009090] Console: colour dummy device 80x25 <4>[ 0.013858] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.021892] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.026283] ... MAX_LOCK_DEPTH: 48 <4>[ 0.030761] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.035412] ... CLASSHASH_SIZE: 4096 <4>[ 0.040063] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.044801] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.049538] ... CHAINHASH_SIZE: 32768 <4>[ 0.054276] memory used by lock dependency info: 7391 kB <4>[ 0.059967] per task-struct memory footprint: 1920 bytes <6>[ 0.065809] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) <6>[ 0.076367] pid_max: default: 32768 minimum: 301 <6>[ 0.081541] Security Framework initialized <6>[ 0.088040] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) <6>[ 0.096519] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) <6>[ 0.103949] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) <6>[ 0.110984] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes) <6>[ 0.123572] ASID allocator initialised with 32768 entries <6>[ 0.129810] rcu: Hierarchical SRCU implementation. <6>[ 0.137633] EFI services will not be available. <6>[ 0.143402] smp: Bringing up secondary CPUs ... <6>[ 0.150969] Detected VIPT I-cache on CPU1 <6>[ 0.151060] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] <6>[ 0.154108] Detected VIPT I-cache on CPU2 <6>[ 0.154171] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] <6>[ 0.156719] Detected VIPT I-cache on CPU3 <6>[ 0.156777] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] <6>[ 0.157166] smp: Brought up 1 node, 4 CPUs <6>[ 0.195031] SMP: Total of 4 processors activated. <6>[ 0.200090] CPU features: detected: 32-bit EL0 Support <6>[ 0.207228] CPU: All CPU(s) started at EL2 <6>[ 0.211718] alternatives: patching kernel code <6>[ 0.220364] devtmpfs: initialized <6>[ 0.244325] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.254530] futex hash table entries: 1024 (order: 5, 131072 bytes) <6>[ 0.263425] pinctrl core: initialized pinctrl subsystem <6>[ 0.274064] DMI not present or invalid. <6>[ 0.280288] NET: Registered protocol family 16 <6>[ 0.286421] audit: initializing netlink subsys (disabled) <5>[ 0.292652] audit: type=2000 audit(0.200:1): state=initialized audit_enabled=0 res=1 <6>[ 0.300846] cpuidle: using governor menu <6>[ 0.306227] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.318645] DMA: preallocated 256 KiB pool for atomic allocations <6>[ 0.328128] Serial: AMBA PL011 UART driver <6>[ 0.422055] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.430862] cryptd: max_cpu_qlen set to 1000 <6>[ 0.438458] ACPI: Interpreter disabled. <6>[ 0.447526] vgaarb: loaded <5>[ 0.451657] SCSI subsystem initialized <6>[ 0.458303] usbcore: registered new interface driver usbfs <6>[ 0.464428] usbcore: registered new interface driver hub <6>[ 0.470240] usbcore: registered new device driver usb <6>[ 0.478146] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.483448] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.492990] PTP clock support registered <6>[ 0.497769] EDAC MC: Ver: 3.0.0 <6>[ 0.506169] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.516010] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.813269] VFS: Disk quotas dquot_6.6.0 <6>[ 0.817688] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.825582] pnp: PnP ACPI: disabled <6>[ 0.860999] NET: Registered protocol family 2 <6>[ 0.866368] IP idents hash table entries: 32768 (order: 6, 262144 bytes) <6>[ 0.875681] tcp_listen_portaddr_hash hash table entries: 1024 (order: 4, 73728 bytes) <6>[ 0.884197] TCP established hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.892678] TCP bind hash table entries: 16384 (order: 8, 1048576 bytes) <6>[ 0.902166] TCP: Hash tables configured (established 16384 bind 16384) <6>[ 0.909711] UDP hash table entries: 1024 (order: 5, 163840 bytes) <6>[ 0.916618] UDP-Lite hash table entries: 1024 (order: 5, 163840 bytes) <6>[ 0.924336] NET: Registered protocol family 1 <6>[ 0.930986] RPC: Registered named UNIX socket transport module. <6>[ 0.937271] RPC: Registered udp transport module. <6>[ 0.942292] RPC: Registered tcp transport module. <6>[ 0.947312] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.954994] Unpacking initramfs... <6>[ 2.570688] Freeing initrd memory: 16360K <6>[ 2.576453] kvm [1]: 8-bit VMID <6>[ 2.589947] kvm [1]: vgic interrupt IRQ1 <6>[ 2.594573] kvm [1]: Hyp mode initialized successfully <5>[ 2.616408] Initialise system trusted keyrings <6>[ 2.621924] workingset: timestamp_bits=44 max_order=19 bucket_order=0 <6>[ 2.668594] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.677434] NFS: Registering the id_resolver key type <5>[ 2.682974] Key type id_resolver registered <5>[ 2.687527] Key type id_legacy registered <6>[ 2.691901] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 2.698988] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 2.707364] 9p: Installing v9fs 9p2000 file system support <5>[ 2.724419] Key type asymmetric registered <5>[ 2.729016] Asymmetric key parser 'x509' registered <6>[ 2.734406] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) <6>[ 2.742234] io scheduler noop registered <6>[ 2.746503] io scheduler deadline registered <6>[ 2.751672] io scheduler cfq registered (default) <6>[ 2.756726] io scheduler mq-deadline registered <6>[ 2.761582] io scheduler kyber registered <4>[ 2.766570] test_firmware: interface ready <3>[ 2.774867] sun50i-de2-bus 1000000.de2: Error couldn't map SRAM to device <3>[ 2.785323] sun4i-usb-phy 1c19400.phy: failed to get clock usb0_phy <6>[ 2.815511] sun50i-a64-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver <4>[ 2.836902] EINJ: ACPI disabled. <6>[ 2.880806] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.896845] SuperH (H)SCI(F) driver initialized <6>[ 2.902845] msm_serial: driver initialized <4>[ 2.910173] cacheinfo: Unable to detect cache hierarchy for CPU 0 <6>[ 2.951066] loop: module loaded <6>[ 2.972469] thunder_xcv, ver 1.0 <6>[ 2.976282] thunder_bgx, ver 1.0 <6>[ 2.980022] nicpf, ver 1.0 <6>[ 2.984882] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.991058] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.997494] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 3.004799] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.010896] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k <6>[ 3.019067] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 3.026538] sky2: driver version 1.30 <6>[ 3.033309] VFIO - User Level meta-driver version: 0.3 <6>[ 3.043315] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.050219] ehci-pci: EHCI PCI platform driver <6>[ 3.055139] ehci-platform: EHCI generic platform driver <6>[ 3.062662] ehci-orion: EHCI orion driver <6>[ 3.067421] ehci-exynos: EHCI EXYNOS driver <6>[ 3.072335] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.078909] ohci-pci: OHCI PCI platform driver <6>[ 3.083849] ohci-platform: OHCI generic platform driver <6>[ 3.090969] ohci-exynos: OHCI EXYNOS driver <6>[ 3.097189] usbcore: registered new interface driver usb-storage <6>[ 3.114058] sun6i-rtc 1f00000.rtc: rtc core: registered rtc-sun6i as rtc0 <6>[ 3.121216] sun6i-rtc 1f00000.rtc: RTC enabled <6>[ 3.127100] i2c /dev entries driver <6>[ 3.144802] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.151321] sdhci: Copyright(c) Pierre Ossman <6>[ 3.157084] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.166313] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.176325] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.186829] usbcore: registered new interface driver usbhid <6>[ 3.192748] usbhid: USB HID core driver <6>[ 3.208264] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.215741] IPv4 over IPsec tunneling driver <6>[ 3.224080] NET: Registered protocol family 10 <6>[ 3.232740] Segment Routing with IPv6 <6>[ 3.240997] NET: Registered protocol family 17 <6>[ 3.246097] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <6>[ 3.259615] 8021q: 802.1Q VLAN Support v1.8 <6>[ 3.264708] 9pnet: Installing 9P2000 support <5>[ 3.269585] Key type dns_resolver registered <6>[ 3.286331] registered taskstats version 1 <5>[ 3.290781] Loading compiled-in X.509 certificates <6>[ 3.356678] sunxi-rsb 1f03400.rsb: RSB running at 3000000 Hz <6>[ 3.364416] axp20x-rsb sunxi-rsb-3a3: AXP20x variant AXP803 found <6>[ 3.390726] vcc-3v3: supplied by regulator-dummy <6>[ 3.397792] vdd-cpux: supplied by regulator-dummy <6>[ 3.405102] dcdc4: supplied by regulator-dummy <6>[ 3.410650] vcc-dram: supplied by regulator-dummy <6>[ 3.417156] vdd-sys: supplied by regulator-dummy <6>[ 3.424030] vcc-phy: supplied by regulator-dummy <6>[ 3.430224] aldo1: supplied by regulator-dummy <6>[ 3.435676] vcc-pl: supplied by regulator-dummy <6>[ 3.441996] vcc-pll-avcc: supplied by regulator-dummy <6>[ 3.449634] vcc-hdmi: supplied by regulator-dummy <6>[ 3.456172] vcc-mipi: supplied by regulator-dummy <6>[ 3.462559] dldo3: supplied by regulator-dummy <6>[ 3.468818] vcc-wifi: supplied by regulator-dummy <6>[ 3.475248] cpvdd: supplied by regulator-dummy <6>[ 3.481461] eldo2: supplied by regulator-dummy <6>[ 3.487685] eldo3: supplied by regulator-dummy <6>[ 3.493927] vcc-1v2-hsic: supplied by regulator-dummy <6>[ 3.500152] vdd-cpus: supplied by regulator-dummy <6>[ 3.506739] vcc-rtc: supplied by regulator-dummy <6>[ 3.513603] ldo-io0: supplied by regulator-dummy <6>[ 3.519936] ldo-io1: supplied by regulator-dummy <6>[ 3.525317] axp20x-rsb sunxi-rsb-3a3: AXP20X driver loaded <6>[ 3.554452] sun50i-a64-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver <6>[ 3.568115] console [ttyS0] disabled <6>[ 3.592513] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 17, base_baud = 1500000) is a U6_16550A <6>[ 3.602022] console [ttyS0] enabled <6>[ 3.602022] console [ttyS0] enabled <6>[ 3.609602] bootconsole [uart0] disabled <6>[ 3.609602] bootconsole [uart0] disabled <6>[ 3.623882] ehci-platform 1c1a000.usb: EHCI Host Controller <6>[ 3.630153] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1 <6>[ 3.641158] ehci-platform 1c1a000.usb: irq 10, io mem 0x01c1a000 <6>[ 3.660075] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00 <6>[ 3.670478] hub 1-0:1.0: USB hub found <6>[ 3.674900] hub 1-0:1.0: 1 port detected <6>[ 3.684677] ehci-platform 1c1b000.usb: EHCI Host Controller <6>[ 3.690648] ehci-platform 1c1b000.usb: new USB bus registered, assigned bus number 2 <6>[ 3.699887] ehci-platform 1c1b000.usb: irq 12, io mem 0x01c1b000 <6>[ 3.720067] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00 <6>[ 3.729322] hub 2-0:1.0: USB hub found <6>[ 3.733549] hub 2-0:1.0: 1 port detected <6>[ 3.742443] ohci-platform 1c1a400.usb: Generic Platform OHCI controller <6>[ 3.749476] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 3 <6>[ 3.758355] ohci-platform 1c1a400.usb: irq 11, io mem 0x01c1a400 <6>[ 3.830876] hub 3-0:1.0: USB hub found <6>[ 3.835095] hub 3-0:1.0: 1 port detected <6>[ 3.843934] ohci-platform 1c1b400.usb: Generic Platform OHCI controller <6>[ 3.850980] ohci-platform 1c1b400.usb: new USB bus registered, assigned bus number 4 <6>[ 3.859851] ohci-platform 1c1b400.usb: irq 13, io mem 0x01c1b400 <6>[ 3.930566] hub 4-0:1.0: USB hub found <6>[ 3.934796] hub 4-0:1.0: 1 port detected <4>[ 3.944745] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regulator <6>[ 3.956478] usb_phy_generic usb_phy_generic.0.auto: Linked as a consumer to regulator.0 <6>[ 3.967765] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver <6>[ 3.973917] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 5 <6>[ 3.985458] hub 5-0:1.0: USB hub found <6>[ 3.990057] hub 5-0:1.0: 1 port detected <6>[ 4.009535] sunxi-mmc 1c0f000.mmc: Linked as a consumer to regulator.1 <6>[ 4.018427] sunxi-mmc 1c0f000.mmc: Got CD GPIO <6>[ 4.050193] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode <6>[ 4.061264] sun6i-rtc 1f00000.rtc: setting system clock to 1970-01-01 00:00:23 UTC (23) <6>[ 4.117016] mmc0: new high speed SDXC card at address aaaa <6>[ 4.127371] mmcblk0: mmc0:aaaa SE64G 59.5 GiB <6>[ 4.137615] mmcblk0: p1 <6>[ 16.352790] ALSA device list: <6>[ 16.356108] No soundcards found. <6>[ 16.385214] Freeing unused kernel memory: 1920K <6>[ 16.390368] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 16.637313] udevd[1531]: starting version 3.2.9 <5>[ 16.645452] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 16.653095] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 16.660356] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 16.678330] udevd[1531]: specified user 'tss' unknown <27>[ 16.684074] udevd[1531]: specified group 'tss' unknown <30>[ 16.695129] udevd[1532]: starting eudev-3.2.9 <4>[ 17.339924] dwmac-sun8i 1c30000.ethernet: PTP uses main clock <6>[ 17.349568] dwmac-sun8i 1c30000.ethernet: Linked as a consumer to regulator.6 <4>[ 17.360650] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 6 (expect 0) <6>[ 17.369807] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported <6>[ 17.379085] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported <6>[ 17.387345] dwmac-sun8i 1c30000.ethernet: COE Type 2 <6>[ 17.393068] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported <6>[ 17.400651] dwmac-sun8i 1c30000.ethernet: Normal descriptors <6>[ 17.407055] dwmac-sun8i 1c30000.ethernet: Chain mode enabled done Saving random seed: OK Starting network: OK Starting dropbear sshd: <5>[ 17.813035] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-319889/environment . /lava-319889/environment / # /lava-319889/bin/lava-test-runner /lava-319889/0 /lava-319889/bin/lava-test-runner /lava-319889/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-319889/0/tests/0_dmesg + cat uuid + UUID=319889_1.5.2.4.1<8>[ 18.459350] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 18.531913] <8>[ 18.597711] <8>[ 18.663613] + set +x <8>[ 18.676110] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-319889/environment / # . /lava-319889/environment/lava-319889/bin/lava-test-runner /lava-319889/1 / # /lava-319889/bin/lava-test-runner /lava-319889/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-319889/1/tests/1_bootrr + cat uuid + UUID=319889_1.5.2.4.5<8>[ 19.202526] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-319889/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto sound_spdif /lava-319889/1/../bin/lava-test-case <8>[ 20.305445] /lava-319889/1/../bin/lava-test-case <8>[ 20.373287] /lava-319889/1/../bin/lava-test-case <8>[ 20.412305] /lava-319889/1/../bin/lava-test-case <8>[ 20.492440] /lava-319889/1/../bin/lava-test-case <8>[ 20.563034] /lava-319889/1/../bin/lava-test-case <8>[ 20.622765] /lava-319889/1/../bin/lava-test-case <8>[ 20.692843] /lava-319889/1/../bin/lava-test-case <8>[ 20.745212] /lava-319889/1/../bin/lava-test-case <8>[ 20.815234] /lava-319889/1/../bin/lava-test-case <8>[ 20.868520] /lava-319889/1/../bin/lava-test-case <8>[ 20.938078] /lava-319889/1/../bin/lava-test-case <8>[ 21.006720] /lava-319889/1/../bin/lava-test-case <8>[ 21.058990] /lava-319889/1/../bin/lava-test-case <8>[ 21.128668] /lava-319889/1/../bin/lava-test-case <8>[ 21.197156] /lava-319889/1/../bin/lava-test-case <8>[ 21.249461] /lava-319889/1/../bin/lava-test-case <8>[ 21.319245] /lava-319889/1/../bin/lava-test-case <8>[ 21.371596] /lava-319889/1/../bin/lava-test-case <8>[ 21.441035] /lava-319889/1/../bin/lava-test-case <8>[ 22.502875] /lava-319889/1/../bin/lava-test-case <8>[ 23.566848] /lava-319889/1/../bin/lava-test-case <8>[ 24.629383] /lava-319889/1/../bin/lava-test-case <8>[ 25.692392] /lava-319889/1/../bin/lava-test-case <8>[ 26.754111] /lava-319889/1/../bin/lava-test-case <8>[ 27.816776] /lava-319889/1/../bin/lava-test-case <8>[ 28.873238] /lava-319889/1/../bin/lava-test-case <8>[ 29.934715] /lava-319889/1/../bin/lava-test-case <8>[ 30.997625] /lava-319889/1/../bin/lava-test-case <8>[ 31.051501] /lava-319889/1/../bin/lava-test-case <8>[ 31.089691] /lava-319889/1/../bin/lava-test-case <8>[ 32.151134] /lava-319889/1/../bin/lava-test-case <8>[ 33.215254] /lava-319889/1/../bin/lava-test-case <8>[ 34.276727] /lava-319889/1/../bin/lava-test-case <8>[ 35.339379] /lava-319889/1/../bin/lava-test-case <8>[ 36.401654] /lava-319889/1/../bin/lava-test-case <8>[ 37.463862] /lava-319889/1/../bin/lava-test-case <8>[ 37.517076] /lava-319889/1/../bin/lava-test-case <8>[ 37.586681] /lava-319889/1/../bin/lava-test-case <8>[ 38.648338] /lava-319889/1/../bin/lava-test-case <8>[ 39.711353] /lava-319889/1/../bin/lava-test-case <8>[ 40.773069] BusyBox v1.31.1 (2023-06-23 08:09:45 UTC) multi-call binary. Usage: seq [-w] [-s SEP] [FIRST [INC]] LAST Print numbers from FIRST to LAST, in steps of INC. FIRST, INC default to 1. -w Pad to last with leading zeros -s SEP String separator /lava-319889/1/../bin/lava-test-case <8>[ 40.827707] BusyBox v1.31.1 (2023-06-23 08:09:45 UTC) multi-call binary. Usage: seq [-w] [-s SEP] [FIRST [INC]] LAST Print numbers from FIRST to LAST, in steps of INC. FIRST, INC default to 1. -w Pad to last with leading zeros -s SEP String separator /lava-319889/1/../bin/lava-test-case <8>[ 40.885969] /lava-319889/1/../bin/lava-test-case <8>[ 41.951388] /lava-319889/1/../bin/lava-test-case <8>[ 43.013477] + set +x <8>[ 43.027010] / #