[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.38 (12 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12709770/tftp-deploy-bx4h2vy_/kernel/zImage tftp 0x10000000 12709770/tftp-deploy-bx4h2vy_/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '12709770/tftp-deploy-bx4h2vy_/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 5.8 MiB/s done Bytes transferred = 10342912 (9dd200 hex) => tftp 0x14000000 12709770/tftp-deploy-bx4h2vy_/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12709770/tftp-deploy-bx4h2vy_/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '12709770/tftp-deploy-bx4h2vy_/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######## 14.3 MiB/s done Bytes transferred = 11559064 (b06098 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12709770/tftp-deploy-bx4h2vy_/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12709770/tftp-deploy-bx4h2vy_/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '12709770/tftp-deploy-bx4h2vy_/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.7 MiB/s done Bytes transferred = 41822 (a35e hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12709770/extract-nfsrootfs-e1_6ptw1,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12709770/extract-nfsrootfs-e1_6ptw1,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x9dd200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 11559000 Bytes = 11 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d35d Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.304-cip106 (KernelCI@build-j100073-arm-gcc-10-multi-v7-defconfig-kselftest-78tct) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Tue Feb 6 22:18:03 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s40104 r8192 d21336 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12709770/extract-nfsrootfs-e1_6ptw1,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 929272K/1048576K available (14336K kernel code, 1760K rwdata, 6292K rodata, 2048K init, 7703K bss, 53768K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (15328 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1761 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7704 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 48541 entries in 190 pages <6>[ 0.000000] ftrace: allocated 190 pages with 6 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021935] Console: colour dummy device 80x30 <4>[ 0.023822] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.031849] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.036191] ... MAX_LOCK_DEPTH: 48 <4>[ 0.040599] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.045209] ... CLASSHASH_SIZE: 4096 <4>[ 0.049849] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.054519] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.059246] ... CHAINHASH_SIZE: 32768 <4>[ 0.063916] memory used by lock dependency info: 4655 kB <4>[ 0.069598] per task-struct memory footprint: 1536 bytes <6>[ 0.075274] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.085701] CPU: Testing write buffer coherency: ok <6>[ 0.090801] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.096140] pid_max: default: 32768 minimum: 301 <6>[ 0.101294] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.107907] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.117958] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.123299] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.130133] rcu: Hierarchical SRCU implementation. <6>[ 0.137252] EFI services will not be available. <6>[ 0.140142] smp: Bringing up secondary CPUs ... <6>[ 0.146401] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.146413] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.158004] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.158017] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.168902] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.168913] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.178134] smp: Brought up 1 node, 4 CPUs <6>[ 0.182015] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.188536] CPU: All CPU(s) started in SVC mode. <6>[ 0.196052] devtmpfs: initialized <6>[ 0.232871] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.240513] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.248213] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.258510] pinctrl core: initialized pinctrl subsystem <6>[ 0.266225] DMI not present or invalid. <6>[ 0.269382] NET: Registered protocol family 16 <6>[ 0.280393] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.291263] cpuidle: using governor menu <6>[ 0.293099] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.332704] vdd1p1: supplied by regulator-dummy <6>[ 0.336697] vdd3p0: supplied by regulator-dummy <6>[ 0.341225] vdd2p5: supplied by regulator-dummy <6>[ 0.346063] vddarm: supplied by regulator-dummy <6>[ 0.351450] vddpu: supplied by regulator-dummy <6>[ 0.355020] vddsoc: supplied by regulator-dummy <6>[ 0.406837] No ATAGs? <6>[ 0.407317] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.415319] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.432596] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.440609] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.464351] Serial: AMBA PL011 UART driver <6>[ 0.565827] mxs-dma 110000.dma-apbh: initialized <6>[ 0.591937] vgaarb: loaded <5>[ 0.594977] SCSI subsystem initialized <6>[ 0.597656] usbcore: registered new interface driver usbfs <6>[ 0.602098] usbcore: registered new interface driver hub <6>[ 0.607702] usbcore: registered new device driver usb <6>[ 0.617395] i2c i2c-0: IMX I2C adapter registered <6>[ 0.619551] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.626907] i2c i2c-1: IMX I2C adapter registered <6>[ 0.630073] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.637120] i2c i2c-2: IMX I2C adapter registered <6>[ 0.640599] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.650179] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.652570] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.662068] PTP clock support registered <6>[ 0.666990] EDAC MC: Ver: 3.0.0 <6>[ 0.680736] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.943941] NET: Registered protocol family 2 <6>[ 0.946380] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.955583] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 20480 bytes) <6>[ 0.960966] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.968245] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) <6>[ 0.976173] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.982064] UDP hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.987843] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.994930] NET: Registered protocol family 1 <6>[ 1.000907] RPC: Registered named UNIX socket transport module. <6>[ 1.005051] RPC: Registered udp transport module. <6>[ 1.009999] RPC: Registered tcp transport module. <6>[ 1.015039] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.023619] Trying to unpack rootfs image as initramfs... <6>[ 2.231210] Freeing initrd memory: 11292K <4>[ 2.233478] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 2.241675] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 2.256002] Initialise system trusted keyrings <6>[ 2.258698] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.293640] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.299586] NFS: Registering the id_resolver key type <5>[ 2.302401] Key type id_resolver registered <5>[ 2.306657] Key type id_legacy registered <6>[ 2.311149] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.322910] Key type asymmetric registered <5>[ 2.324506] Asymmetric key parser 'x509' registered <6>[ 2.329822] bounce: pool size: 64 pages <6>[ 2.333833] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 2.341414] io scheduler noop registered <6>[ 2.345492] io scheduler deadline registered <6>[ 2.350486] io scheduler cfq registered (default) <6>[ 2.355026] io scheduler mq-deadline registered <6>[ 2.359758] io scheduler kyber registered <4>[ 2.364662] test_firmware: interface ready <6>[ 2.442994] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.447999] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.455464] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.462278] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.514491] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 2.518160] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 2.525875] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 2.532316] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 2.540164] PU : no governor for states <6>[ 2.543855] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <4>[ 2.575650] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 2.582833] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 2.769852] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.786133] SuperH (H)SCI(F) driver initialized <6>[ 2.790247] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 2.799768] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 2.808914] console [ttymxc1] enabled <6>[ 2.808914] console [ttymxc1] enabled <6>[ 2.814007] bootconsole [ec_imx21] disabled <6>[ 2.814007] bootconsole [ec_imx21] disabled <6>[ 2.826909] msm_serial: driver initialized <6>[ 2.832206] STMicroelectronics ASC driver initialized <6>[ 2.842694] STM32 USART driver initialized <6>[ 2.862476] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 2.886962] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.895916] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.903225] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.910252] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.919518] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.927093] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.964023] brd: module loaded <6>[ 2.996087] loop: module loaded <6>[ 3.009376] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.017640] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.025990] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.034500] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 3.045905] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.053257] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.062569] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.075582] scsi host0: ahci-imx <6>[ 3.081065] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 3.125778] CAN device driver interface <6>[ 3.133426] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 3.142393] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 3.151619] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 3.161802] pps pps0: new PPS source ptp0 <6>[ 3.200524] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.209873] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 3.216059] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.222480] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 3.229725] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.252539] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.260352] usbcore: registered new interface driver pegasus <6>[ 3.266516] usbcore: registered new interface driver asix <6>[ 3.272357] usbcore: registered new interface driver ax88179_178a <6>[ 3.278837] usbcore: registered new interface driver cdc_ether <6>[ 3.285155] usbcore: registered new interface driver smsc75xx <6>[ 3.291417] usbcore: registered new interface driver smsc95xx <6>[ 3.297554] usbcore: registered new interface driver net1080 <6>[ 3.303653] usbcore: registered new interface driver cdc_subset <6>[ 3.309956] usbcore: registered new interface driver zaurus <6>[ 3.316085] usbcore: registered new interface driver cdc_ncm <6>[ 3.330597] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.337416] ehci-pci: EHCI PCI platform driver <6>[ 3.342305] ehci-platform: EHCI generic platform driver <6>[ 3.348601] ehci-orion: EHCI orion driver <6>[ 3.353679] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.358648] ehci-st: EHCI STMicroelectronics driver <6>[ 3.364527] ehci-exynos: EHCI EXYNOS driver <6>[ 3.369654] ehci-atmel: EHCI Atmel driver <6>[ 3.374651] tegra-ehci: Tegra EHCI driver <6>[ 3.379640] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.386206] ohci-pci: OHCI PCI platform driver <6>[ 3.391098] ohci-platform: OHCI generic platform driver <6>[ 3.397372] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.402388] ohci-st: OHCI STMicroelectronics driver <6>[ 3.408229] ohci-atmel: OHCI Atmel driver <6>[ 3.415276] usbcore: registered new interface driver usb-storage <6>[ 3.423151] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.427941] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 3.428965] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.442185] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.445944] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 3.461449] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.466813] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.500699] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.510314] hub 1-0:1.0: USB hub found <6>[ 3.514754] hub 1-0:1.0: 1 port detected <6>[ 3.541661] i2c /dev entries driver <6>[ 3.593584] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 3.615242] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.621760] sdhci: Copyright(c) Pierre Ossman <6>[ 3.632737] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.645034] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.653108] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 3.658627] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 3.664552] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 3.708239] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 3.716985] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 3.722922] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 3.765363] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 3.784705] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.794149] usbcore: registered new interface driver usbhid <6>[ 3.800052] usbhid: USB HID core driver <6>[ 3.805384] mmc0: new high speed SDHC card at address 0001 <6>[ 3.815672] mmcblk0: mmc0:0001 SD 14.6 GiB <6>[ 3.821547] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 3.822041] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.835911] IPv4 over IPsec tunneling driver <6>[ 3.844295] NET: Registered protocol family 10 <6>[ 3.852878] Segment Routing with IPv6 <6>[ 3.859208] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.869536] NET: Registered protocol family 17 <6>[ 3.874362] can: controller area network core (rev 20170425 abi 9) <6>[ 3.881248] NET: Registered protocol family 29 <6>[ 3.885993] can: raw protocol (rev 20170425) <6>[ 3.890781] can: broadcast manager protocol (rev 20170425 t) <6>[ 3.896759] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 3.904001] Key type dns_resolver registered <6>[ 3.920454] cpu cpu0: Linked as a consumer to regulator.4 <4>[ 3.926334] ------------[ cut here ]------------ <6>[ 3.926470] cpu cpu0: Linked as a consumer to regulator.5 <4>[ 3.931239] WARNING: CPU: 1 PID: 0 at include/trace/events/lock.h:13 lock_acquire+0x138/0x1f0 <4>[ 3.931245] Modules linked in: <4>[ 3.931259] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.19.304-cip106 #1 <4>[ 3.931269] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <6>[ 3.937198] cpu cpu0: Linked as a consumer to regulator.6 <4>[ 3.945712] Backtrace: <4>[ 3.945734] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 3.945745] r7:ffffffff r6:00000000 r5:60000093 r4:c1b9ce48 <4>[ 3.945762] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 3.945778] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <6>[ 3.953596] ThumbEE CPU extension supported. <4>[ 3.956056] r9:60000093 r8:c1a084bc r7:00000000 r6:00000009 r5:00000000 r4:00000000 <4>[ 3.960699] ------------[ cut here ]------------ <4>[ 3.960718] WARNING: CPU: 3 PID: 0 at include/trace/events/lock.h:58 lock_release+0x364/0x370 <4>[ 3.960723] Modules linked in: <5>[ 3.962943] Registering SWP/SWPB emulation handler <4>[ 3.968512] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 3.968521] r6:c03b8c7c r5:0000000d r4:c157d8a8 <4>[ 4.048226] [] (warn_slowpath_null) from [] (lock_acquire+0x138/0x1f0) <4>[ 4.056776] r6:00000000 r5:00000000 r4:c1a10fd0 <4>[ 4.061695] [] (lock_acquire) from [] (_raw_spin_lock+0x58/0x68) <4>[ 4.069727] r10:c1a084bc r9:00000001 r8:c1ba5110 r7:00000001 r6:c1a10ce4 r5:c1a084bc <4>[ 4.077833] r4:c1a10fc0 <4>[ 4.080672] [] (_raw_spin_lock) from [] (imx6q_enter_wait+0x30/0xb4) <4>[ 4.089039] r4:c1bba4b8 <4>[ 4.091872] [] (imx6q_enter_wait) from [] (cpuidle_enter_state+0x188/0x518) <4>[ 4.100853] r7:ef7ab2f8 r6:c1a10ce4 r5:c1a10c84 r4:00000001 <4>[ 4.106800] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 4.115351] r10:c1a10c84 r9:ef7ab2f8 r8:c19a12f0 r7:c1a08500 r6:c1a10c84 r5:ef7ab2f8 <4>[ 4.123457] r4:00000001 <4>[ 4.126294] [] (cpuidle_enter) from [] (do_idle+0x220/0x2e0) <4>[ 4.133975] r7:c1a08500 r6:c1a084bc r5:00000001 r4:ee9d4000 <4>[ 4.139931] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 4.147788] r10:00000000 r9:412fc09a r8:1020406a r7:c1bb9650 r6:00000001 r5:ee9d4000 <4>[ 4.155895] r4:0000008a <4>[ 4.158731] [] (cpu_startup_entry) from [] (secondary_start_kernel+0x170/0x17c) <4>[ 4.168068] [] (secondary_start_kernel) from [<1030312c>] (0x1030312c) <4>[ 4.175749] r7:c1bb9650 r6:10c0387d r5:00000051 r4:3e9c006a <4>[ 4.181686] irq event stamp: 17406 <4>[ 4.181700] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.19.304-cip106 #1 <4>[ 4.181712] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 4.185389] hardirqs last enabled at (17405): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 4.185421] hardirqs last disabled at (17406): [] do_idle+0xb0/0x2e0 <4>[ 4.192373] Backtrace: <4>[ 4.199184] softirqs last enabled at (17398): [] __do_softirq+0x344/0x520 <4>[ 4.208328] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 4.215819] softirqs last disabled at (17375): [] irq_exit+0x170/0x1c8 <4>[ 4.218511] r7:ffffffff r6:00000000 r5:600e0093 r4:c1b9ce48 <4>[ 4.226515] ---[ end trace c61a6b2893ad175a ]--- <4>[ 4.234373] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 4.260404] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <4>[ 4.268175] r9:c032d5c4 r8:c1ba5110 r7:600e0093 r6:00000009 r5:00000000 r4:00000000 <4>[ 4.276208] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 4.284668] r6:c03b8b38 r5:0000003a r4:c157d8a8 <4>[ 4.289579] [] (warn_slowpath_null) from [] (lock_release+0x364/0x370) <4>[ 4.298124] r6:00000001 r5:c1a10fd0 r4:c1a084bc <4>[ 4.303039] [] (lock_release) from [] (_raw_spin_unlock+0x28/0x4c) <4>[ 4.311243] r10:c1a084bc r9:00000001 r8:c1ba5110 r7:00000001 r6:00000001 r5:c1a084bc <4>[ 4.319349] r4:c1a10fc0 <4>[ 4.322182] [] (_raw_spin_unlock) from [] (imx6q_enter_wait+0x54/0xb4) <4>[ 4.330725] r5:c1a084bc r4:c1bba4b8 <4>[ 4.334595] [] (imx6q_enter_wait) from [] (cpuidle_enter_state+0x188/0x518) <4>[ 4.343577] r7:ef7cd2f8 r6:c1a10ce4 r5:c1a10c84 r4:00000001 <4>[ 4.349524] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 4.358076] r10:c1a10c84 r9:ef7cd2f8 r8:c19a12f0 r7:c1a08500 r6:c1a10c84 r5:ef7cd2f8 <4>[ 4.366181] r4:00000001 <4>[ 4.369010] [] (cpuidle_enter) from [] (do_idle+0x220/0x2e0) <4>[ 4.376690] r7:c1a08500 r6:c1a084bc r5:00000003 r4:ee9d8000 <4>[ 4.382643] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 4.390500] r10:00000000 r9:412fc09a r8:1020406a r7:c1bb9650 r6:00000003 r5:ee9d8000 <4>[ 4.398605] r4:0000008a <4>[ 4.401435] [] (cpu_startup_entry) from [] (secondary_start_kernel+0x170/0x17c) <4>[ 4.410768] [] (secondary_start_kernel) from [<1030312c>] (0x1030312c) <4>[ 4.418447] r7:c1bb9650 r6:10c0387d r5:00000051 r4:3e9c006a <4>[ 4.424383] irq event stamp: 12036 <4>[ 4.428078] hardirqs last enabled at (12035): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 4.437236] hardirqs last disabled at (12036): [] do_idle+0xb0/0x2e0 <4>[ 4.444750] softirqs last enabled at (12030): [] _local_bh_enable+0x34/0x68 <4>[ 4.452952] softirqs last disabled at (12029): [] irq_enter+0x6c/0x94 <4>[ 4.460538] ---[ end trace c61a6b2893ad175b ]--- <5>[ 4.469998] Loading compiled-in X.509 certificates <6>[ 4.513860] hub 1-1:1.0: USB hub found <6>[ 4.518248] hub 1-1:1.0: 3 ports detected <6>[ 4.553331] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.561353] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 4.573274] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 4.581084] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.593241] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 4.602229] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 4.609480] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 4.620366] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 4.629609] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 4.637155] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 4.651071] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 4.664059] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.671800] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <4>[ 4.671817] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 4.683250] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <4>[ 4.686697] GPT:29296874 != 30560255 <6>[ 4.694352] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.697882] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.709904] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <4>[ 4.711357] GPT:29296874 != 30560255 <4>[ 4.711367] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.711424] mmcblk0: p1 p2 p3 <6>[ 4.720201] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 4.739844] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 4.750706] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 4.759899] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 4.767286] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 4.777661] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.785275] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 4.796599] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 4.804308] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.816294] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 4.825241] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 4.832451] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 4.843571] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 4.852864] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 4.860197] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 4.870808] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.878359] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 4.889666] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 4.897352] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.909352] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 4.918228] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 4.925436] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 4.937988] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 4.946031] hctosys: unable to open rtc device (rtc0) <4>[ 4.956531] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 4.965904] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 4.973558] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 4.984020] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.991637] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.003046] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.010746] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.022752] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.031642] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.038805] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 5.083849] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 5.099654] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 8.262851] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 8.280774] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.311468] Sending DHCP requests ., OK <6>[ 8.355209] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.38 <6>[ 8.363593] IP-Config: Complete: <6>[ 8.367111] device=eth0, hwaddr=00:19:b8:08:f0:fe, ipaddr=192.168.201.38, mask=255.255.255.0, gw=192.168.201.1 <6>[ 8.377878] host=imx6q-sabrelite-lava-cbg-8, domain=lava-rack, nis-domain=(none) <6>[ 8.386054] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 8.386062] nameserver0=192.168.201.1 <6>[ 8.436233] Freeing unused kernel memory: 2048K <6>[ 8.462143] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 11.354486] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 11.363933] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <4>[ 11.366922] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.381225] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.389978] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 11.400812] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.412858] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.424736] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.433503] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 11.445987] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.454922] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.465913] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 11.471629] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <4>[ 11.484738] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.494076] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.503858] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 11.521050] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.528635] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.534660] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.552813] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.559772] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 11.588889] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.597393] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 11.611639] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.614588] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 11.626884] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.634072] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 11.638655] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 11.647466] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 11.659419] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.668854] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.676693] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 11.676720] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 11.693285] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 11.693902] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.699672] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 11.714148] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.721745] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 11.721839] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 1 <6>[ 11.739640] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.747941] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 11.762983] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.772125] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.781365] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 11.792952] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.802221] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.811602] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 11.822457] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.830081] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.842062] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.849738] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 11.862540] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.871498] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.878719] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 11.889964] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.899325] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.906904] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 11.917785] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.925634] pwm-backlight backlight-lcd: Dropping the link to regulator.8 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f0:fe mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.38 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-8 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 13.981239] systemd[1]: System time before build time, advancing clock. <3>[ 14.062023] cgroup: cgroup2: unknown option "memory_recursiveprot" <30>[ 14.101141] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 14.126670] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 14.176600] systemd[1]: Set hostname to . <30>[ 15.624642] systemd[1]: Queued start job for default target Graphical Interface. <5>[ 15.635187] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 15.645811] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <5>[ 15.681083] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 15.689852] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <5>[ 15.732691] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 15.743257] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 15.784230] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 15.822662] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 15.863758] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 15.912180] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 15.925784] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 15.961425] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 16.001577] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 16.041162] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 16.081959] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 16.125131] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 16.228488] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 16.241536] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 16.286167] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 16.336627] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 16.390405] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 16.435702] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 16.484111] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 16.494694] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 16.513515] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 16.559496] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <5>[ 16.654951] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 16.670869] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <5>[ 16.711641] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 16.727389] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <5>[ 16.761739] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 16.777296] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 16.820338] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 16.866081] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <6>[ 16.896036] fuse init (API version 7.27) <30>[ 16.903537] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 16.972944] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 17.028476] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 17.079230] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 17.152217] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 17.192994] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 17.248869] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 17.325911] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 17.335294] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 17.386071] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 17.395633] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. <30>[ 17.436551] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 17.445609] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. <30>[ 17.485624] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. <30>[ 17.536131] systemd[1]: Finished Remount Root and Kernel File Systems. [ OK ] Finished Remount Root and Kernel File Systems. <30>[ 17.581844] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... <30>[ 17.628271] systemd[1]: Mounting Kernel Configuration File System... Mounting Kernel Configuration File System... <30>[ 17.677944] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. <30>[ 17.688008] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. <5>[ 17.698188] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 17.711909] systemd[1]: Starting Load/Save Random Seed... <5>[ 17.717673] random: systemd-journal: uninitialized urandom read (16 bytes read) Starting Load/Save Random Seed... <5>[ 17.761338] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 17.776519] systemd[1]: Starting Apply Kernel Variables... Starting Apply Kernel Variables... <30>[ 17.822784] systemd[1]: Starting Create System Users... Starting Create System Users... <30>[ 17.876266] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Flush Journal to Persistent Storage... Starting Create Static Device Nodes in /dev... <46>[ 18.186503] systemd-journald[165]: Received client request to flush runtime journal. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Rule-based Manage…for Device Events and Files... <5>[ 19.031369] random: crng init done <5>[ 19.035207] random: 46 urandom warning(s) missed due to ratelimiting [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... Starting Create Volatile Files and Directories... [ OK ] Started Network Service. [ OK ] Finished Create Volatile Files and Directories. Starting Network Name Resolution... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Found device /dev/ttymxc1. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started Network Time Synchronization. [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Started User Login Management. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.304-cip106 #1 SMP Tue Feb 6 22:18:03 UTC 2024 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12709770/extract-nfsrootfs-e1_6ptw1' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12709770/extract-nfsrootfs-e1_6ptw1' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1'<6>[ 38.902837] usb_otg_vbus: disabling <6>[ 38.906952] CAN XCVR: disabling / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-12709770/environment . /lava-12709770/environment / # /lava-12709770/bin/lava-test-runner /lava-12709770/0 /lava-12709770/bin/lava-test-runner /lava-12709770/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-12709770/0/tests/0_timesync-off ++ cat uuid + UUID=12709770_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-lib + TESTRUN_ID=1_kselftest-lib + cd /lava-12709770/0/tests/1_kselftest-lib ++ cat uuid + UUID=12709770_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c lib -T '' -t kselftest_armhf.tar.gz -s True -u None -L '' -S /dev/null -b imx6q-sabrelite -g cip -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2024-02-06 22:33:39-- http://none/ Resolving none (none)... failed: Name or service not known. wget: unable to resolve host address 'none' tar: None: Cannot open: No such file or directory tar: Error is not recoverable: exiting now ./kselftest.sh: 160: cd: can't cd to kselftest / #