[Enter `^Ec?' for help]  U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.33 (13 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12709778/tftp-deploy-vji8wtmb/kernel/zImage tftp 0x10000000 12709778/tftp-deploy-vji8wtmb/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '12709778/tftp-deploy-vji8wtmb/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 5.8 MiB/s done Bytes transferred = 10342912 (9dd200 hex) => tftp 0x14000000 12709778/tftp-deploy-vji8wtmb/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12709778/tftp-deploy-vji8wtmb/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '12709778/tftp-deploy-vji8wtmb/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 13.9 MiB/s done Bytes transferred = 11568347 (b084db hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12709778/tftp-deploy-vji8wtmb/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12709778/tftp-deploy-vji8wtmb/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '12709778/tftp-deploy-vji8wtmb/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.7 MiB/s done Bytes transferred = 41822 (a35e hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12709778/extract-nfsrootfs-alvixms7,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12709778/extract-nfsrootfs-alvixms7,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x9dd200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 11568283 Bytes = 11 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d35d Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.304-cip106 (KernelCI@build-j100073-arm-gcc-10-multi-v7-defconfig-kselftest-78tct) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Tue Feb 6 22:18:03 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s40104 r8192 d21336 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12709778/extract-nfsrootfs-alvixms7,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 929264K/1048576K available (14336K kernel code, 1760K rwdata, 6292K rodata, 2048K init, 7703K bss, 53776K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (15328 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1761 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7704 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 48541 entries in 190 pages <6>[ 0.000000] ftrace: allocated 190 pages with 6 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021917] Console: colour dummy device 80x30 <4>[ 0.023807] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.031830] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.036175] ... MAX_LOCK_DEPTH: 48 <4>[ 0.040583] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.045194] ... CLASSHASH_SIZE: 4096 <4>[ 0.049833] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.054503] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.059229] ... CHAINHASH_SIZE: 32768 <4>[ 0.063899] memory used by lock dependency info: 4655 kB <4>[ 0.069582] per task-struct memory footprint: 1536 bytes <6>[ 0.075258] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.085684] CPU: Testing write buffer coherency: ok <6>[ 0.090785] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.096123] pid_max: default: 32768 minimum: 301 <6>[ 0.101274] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.107893] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.117926] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.123273] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.130113] rcu: Hierarchical SRCU implementation. <6>[ 0.137255] EFI services will not be available. <6>[ 0.140134] smp: Bringing up secondary CPUs ... <6>[ 0.146395] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.146407] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.157999] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.158011] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.168907] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.168920] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.178133] smp: Brought up 1 node, 4 CPUs <6>[ 0.182018] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.188539] CPU: All CPU(s) started in SVC mode. <6>[ 0.196072] devtmpfs: initialized <6>[ 0.232947] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.240594] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.248286] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.258575] pinctrl core: initialized pinctrl subsystem <6>[ 0.266297] DMI not present or invalid. <6>[ 0.269465] NET: Registered protocol family 16 <6>[ 0.280566] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.291415] cpuidle: using governor menu <6>[ 0.293249] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.332829] vdd1p1: supplied by regulator-dummy <6>[ 0.336828] vdd3p0: supplied by regulator-dummy <6>[ 0.341341] vdd2p5: supplied by regulator-dummy <6>[ 0.346180] vddarm: supplied by regulator-dummy <6>[ 0.351554] vddpu: supplied by regulator-dummy <6>[ 0.355143] vddsoc: supplied by regulator-dummy <6>[ 0.406924] No ATAGs? <6>[ 0.407408] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.415409] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.432727] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.440730] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.464507] Serial: AMBA PL011 UART driver <6>[ 0.566050] mxs-dma 110000.dma-apbh: initialized <6>[ 0.592126] vgaarb: loaded <5>[ 0.595146] SCSI subsystem initialized <6>[ 0.597814] usbcore: registered new interface driver usbfs <6>[ 0.602263] usbcore: registered new interface driver hub <6>[ 0.607877] usbcore: registered new device driver usb <6>[ 0.617590] i2c i2c-0: IMX I2C adapter registered <6>[ 0.619746] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.627111] i2c i2c-1: IMX I2C adapter registered <6>[ 0.630268] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.637300] i2c i2c-2: IMX I2C adapter registered <6>[ 0.640798] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.650411] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.652801] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.662296] PTP clock support registered <6>[ 0.667223] EDAC MC: Ver: 3.0.0 <6>[ 0.680952] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.944601] NET: Registered protocol family 2 <6>[ 0.947043] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.956237] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 20480 bytes) <6>[ 0.961620] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.968903] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) <6>[ 0.976824] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.982721] UDP hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.988499] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.995592] NET: Registered protocol family 1 <6>[ 1.001540] RPC: Registered named UNIX socket transport module. <6>[ 1.005705] RPC: Registered udp transport module. <6>[ 1.010655] RPC: Registered tcp transport module. <6>[ 1.015697] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.024303] Trying to unpack rootfs image as initramfs... <6>[ 2.229194] Freeing initrd memory: 11300K <4>[ 2.231612] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 2.238991] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 2.254129] Initialise system trusted keyrings <6>[ 2.256820] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.291937] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.297900] NFS: Registering the id_resolver key type <5>[ 2.300603] Key type id_resolver registered <5>[ 2.305036] Key type id_legacy registered <6>[ 2.309361] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.321434] Key type asymmetric registered <5>[ 2.323025] Asymmetric key parser 'x509' registered <6>[ 2.328348] bounce: pool size: 64 pages <6>[ 2.332357] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 2.339885] io scheduler noop registered <6>[ 2.344075] io scheduler deadline registered <6>[ 2.349016] io scheduler cfq registered (default) <6>[ 2.353557] io scheduler mq-deadline registered <6>[ 2.358283] io scheduler kyber registered <4>[ 2.363184] test_firmware: interface ready <6>[ 2.441612] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.446629] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.454058] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.460909] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.513260] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 2.516924] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 2.524642] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 2.531038] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 2.538927] PU : no governor for states <6>[ 2.542632] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <4>[ 2.574380] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 2.581585] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 2.761691] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.777937] SuperH (H)SCI(F) driver initialized <6>[ 2.782121] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 2.791630] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 2.800740] console [ttymxc1] enabled <6>[ 2.800740] console [ttymxc1] enabled <6>[ 2.805836] bootconsole [ec_imx21] disabled <6>[ 2.805836] bootconsole [ec_imx21] disabled <6>[ 2.818793] msm_serial: driver initialized <6>[ 2.824098] STMicroelectronics ASC driver initialized <6>[ 2.834579] STM32 USART driver initialized <6>[ 2.854204] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 2.878700] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.887660] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.894964] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.902033] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.911299] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.918686] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.955061] brd: module loaded <6>[ 2.986972] loop: module loaded <6>[ 3.000172] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.008455] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.016801] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.025312] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 3.036690] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.044088] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.053235] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.066262] scsi host0: ahci-imx <6>[ 3.071696] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 3.116639] CAN device driver interface <6>[ 3.124231] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 3.133213] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 3.142462] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 3.152604] pps pps0: new PPS source ptp0 <6>[ 3.192036] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.201372] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 3.207492] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.213927] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 3.221220] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.244051] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.251902] usbcore: registered new interface driver pegasus <6>[ 3.257998] usbcore: registered new interface driver asix <6>[ 3.263836] usbcore: registered new interface driver ax88179_178a <6>[ 3.270318] usbcore: registered new interface driver cdc_ether <6>[ 3.276648] usbcore: registered new interface driver smsc75xx <6>[ 3.282882] usbcore: registered new interface driver smsc95xx <6>[ 3.289018] usbcore: registered new interface driver net1080 <6>[ 3.295113] usbcore: registered new interface driver cdc_subset <6>[ 3.301505] usbcore: registered new interface driver zaurus <6>[ 3.307563] usbcore: registered new interface driver cdc_ncm <6>[ 3.322072] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.328889] ehci-pci: EHCI PCI platform driver <6>[ 3.333780] ehci-platform: EHCI generic platform driver <6>[ 3.340110] ehci-orion: EHCI orion driver <6>[ 3.345178] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.350141] ehci-st: EHCI STMicroelectronics driver <6>[ 3.356023] ehci-exynos: EHCI EXYNOS driver <6>[ 3.361200] ehci-atmel: EHCI Atmel driver <6>[ 3.366157] tegra-ehci: Tegra EHCI driver <6>[ 3.371199] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.377716] ohci-pci: OHCI PCI platform driver <6>[ 3.382611] ohci-platform: OHCI generic platform driver <6>[ 3.388888] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.393908] ohci-st: OHCI STMicroelectronics driver <6>[ 3.399733] ohci-atmel: OHCI Atmel driver <6>[ 3.406843] usbcore: registered new interface driver usb-storage <6>[ 3.413439] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.419278] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.419514] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 3.425888] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.443528] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 3.455432] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.460894] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.490963] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.500514] hub 1-0:1.0: USB hub found <6>[ 3.504943] hub 1-0:1.0: 1 port detected <6>[ 3.531836] i2c /dev entries driver <6>[ 3.583344] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 3.605049] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.611567] sdhci: Copyright(c) Pierre Ossman <6>[ 3.622568] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.634875] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.642940] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 3.648455] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 3.654316] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 3.697881] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 3.706615] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 3.712553] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 3.755543] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 3.774974] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.784314] usbcore: registered new interface driver usbhid <6>[ 3.790172] usbhid: USB HID core driver <6>[ 3.811849] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.819170] IPv4 over IPsec tunneling driver <6>[ 3.827443] NET: Registered protocol family 10 <6>[ 3.833988] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 3.842798] Segment Routing with IPv6 <6>[ 3.849157] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.855743] mmc0: new high speed SDHC card at address aaaa <6>[ 3.859488] NET: Registered protocol family 17 <6>[ 3.866046] mmcblk0: mmc0:aaaa SL16G 14.8 GiB <6>[ 3.866430] can: controller area network core (rev 20170425 abi 9) <6>[ 3.877865] NET: Registered protocol family 29 <6>[ 3.882682] can: raw protocol (rev 20170425) <4>[ 3.883713] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 3.887391] can: broadcast manager protocol (rev 20170425 t) <4>[ 3.895118] GPT:29296874 != 31116287 <6>[ 3.901111] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 3.902617] Key type dns_resolver registered <4>[ 3.904969] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.904983] GPT:29296874 != 31116287 <4>[ 3.915363] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.931049] mmcblk0: p1 p2 p3 <6>[ 3.938545] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 3.944575] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 3.950534] cpu cpu0: Linked as a consumer to regulator.6 <4>[ 3.950942] ------------[ cut here ]------------ <6>[ 3.960671] ThumbEE CPU extension supported. <4>[ 3.961108] WARNING: CPU: 0 PID: 0 at include/trace/events/lock.h:13 lock_acquire+0x138/0x1f0 <4>[ 3.961115] Modules linked in: <4>[ 3.961128] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.304-cip106 #1 <4>[ 3.961134] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 3.961139] Backtrace: <4>[ 3.961160] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 3.961171] r7:ffffffff r6:00000000 r5:60000093 r4:c1b9ce48 <5>[ 3.965733] Registering SWP/SWPB emulation handler <4>[ 3.970939] ------------[ cut here ]------------ <4>[ 3.970957] WARNING: CPU: 2 PID: 0 at include/trace/events/lock.h:58 lock_release+0x364/0x370 <4>[ 3.970961] Modules linked in: <4>[ 3.974499] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 3.974512] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <4>[ 3.974523] r9:60000093 r8:c1a084bc r7:00000000 r6:00000009 r5:00000000 r4:00000000 <4>[ 3.974539] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 4.061885] r6:c03b8c7c r5:0000000d r4:c157d8a8 <4>[ 4.066802] [] (warn_slowpath_null) from [] (lock_acquire+0x138/0x1f0) <4>[ 4.075349] r6:00000000 r5:00000000 r4:c1a10fd0 <4>[ 4.080265] [] (lock_acquire) from [] (_raw_spin_lock+0x58/0x68) <4>[ 4.088297] r10:c1a084bc r9:00000001 r8:c1ba5110 r7:00000001 r6:c1a10ce4 r5:c1a084bc <4>[ 4.096403] r4:c1a10fc0 <4>[ 4.099245] [] (_raw_spin_lock) from [] (imx6q_enter_wait+0x30/0xb4) <4>[ 4.107612] r4:c1bba4b8 <4>[ 4.110442] [] (imx6q_enter_wait) from [] (cpuidle_enter_state+0x188/0x518) <4>[ 4.119423] r7:ef79a2f8 r6:c1a10ce4 r5:c1a10c84 r4:00000001 <4>[ 4.125371] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 4.133923] r10:c1a10c84 r9:ef79a2f8 r8:c19a12f0 r7:c1a08500 r6:c1a10c84 r5:ef79a2f8 <4>[ 4.142030] r4:00000001 <4>[ 4.144867] [] (cpuidle_enter) from [] (do_idle+0x220/0x2e0) <4>[ 4.152549] r7:c1a08500 r6:c1a084bc r5:00000000 r4:c1a00000 <4>[ 4.158503] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 4.166360] r10:c18e4a50 r9:00000001 r8:efffe8c0 r7:c1a08480 r6:00000002 r5:c1a01f78 <4>[ 4.174466] r4:000000cb <4>[ 4.177301] [] (cpu_startup_entry) from [] (rest_init+0x2c8/0x2e0) <4>[ 4.185513] [] (rest_init) from [] (start_kernel+0x468/0x4a4) <4>[ 4.193277] r6:ffffffff r5:00000001 r4:c1bb9058 <4>[ 4.198179] [] (start_kernel) from [<00000000>] ( (null)) <4>[ 4.204822] r10:10c5387d r9:412fc09a r8:13f00000 r7:00000eb9 r6:10c0387d r5:00000051 <4>[ 4.212928] r4:c18004b0 <4>[ 4.215740] irq event stamp: 6570 <4>[ 4.215753] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.19.304-cip106 #1 <4>[ 4.215766] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 4.219358] hardirqs last enabled at (6569): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 4.219386] hardirqs last disabled at (6570): [] do_idle+0xb0/0x2e0 <4>[ 4.226339] Backtrace: <4>[ 4.233149] softirqs last enabled at (6564): [] __do_softirq+0x344/0x520 <4>[ 4.242207] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 4.249606] softirqs last disabled at (6541): [] irq_exit+0x170/0x1c8 <4>[ 4.252303] r7:ffffffff r6:00000000 r5:60000093 r4:c1b9ce48 <4>[ 4.260221] ---[ end trace 08640ee6371021d9 ]--- <4>[ 4.268077] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 4.294023] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <4>[ 4.301795] r9:c032d5c4 r8:c1ba5110 r7:60000093 r6:00000009 r5:00000000 r4:00000000 <4>[ 4.309829] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 4.318288] r6:c03b8b38 r5:0000003a r4:c157d8a8 <4>[ 4.323199] [] (warn_slowpath_null) from [] (lock_release+0x364/0x370) <4>[ 4.331744] r6:00000001 r5:c1a10fd0 r4:c1a084bc <4>[ 4.336658] [] (lock_release) from [] (_raw_spin_unlock+0x28/0x4c) <4>[ 4.344863] r10:c1a084bc r9:00000001 r8:c1ba5110 r7:00000001 r6:00000001 r5:c1a084bc <4>[ 4.352969] r4:c1a10fc0 <4>[ 4.355803] [] (_raw_spin_unlock) from [] (imx6q_enter_wait+0x54/0xb4) <4>[ 4.364346] r5:c1a084bc r4:c1bba4b8 <4>[ 4.368214] [] (imx6q_enter_wait) from [] (cpuidle_enter_state+0x188/0x518) <4>[ 4.377195] r7:ef7bc2f8 r6:c1a10ce4 r5:c1a10c84 r4:00000001 <4>[ 4.383141] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 4.391692] r10:c1a10c84 r9:ef7bc2f8 r8:c19a12f0 r7:c1a08500 r6:c1a10c84 r5:ef7bc2f8 <4>[ 4.399798] r4:00000001 <4>[ 4.402627] [] (cpuidle_enter) from [] (do_idle+0x220/0x2e0) <4>[ 4.410307] r7:c1a08500 r6:c1a084bc r5:00000002 r4:ee9d6000 <4>[ 4.416259] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 4.424116] r10:00000000 r9:412fc09a r8:1020406a r7:c1bb9650 r6:00000002 r5:ee9d6000 <4>[ 4.432221] r4:0000008a <4>[ 4.435055] [] (cpu_startup_entry) from [] (secondary_start_kernel+0x170/0x17c) <4>[ 4.444392] [] (secondary_start_kernel) from [<1030312c>] (0x1030312c) <4>[ 4.452072] r7:c1bb9650 r6:10c0387d r5:00000051 r4:3e9c006a <4>[ 4.458008] irq event stamp: 6024 <4>[ 4.461616] hardirqs last enabled at (6023): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 4.470688] hardirqs last disabled at (6024): [] do_idle+0xb0/0x2e0 <4>[ 4.478116] softirqs last enabled at (6018): [] _local_bh_enable+0x34/0x68 <4>[ 4.486231] softirqs last disabled at (6017): [] irq_enter+0x6c/0x94 <4>[ 4.493730] ---[ end trace 08640ee6371021da ]--- <5>[ 4.500743] Loading compiled-in X.509 certificates <6>[ 4.543934] hub 1-1:1.0: USB hub found <6>[ 4.548397] hub 1-1:1.0: 3 ports detected <6>[ 4.582666] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.590529] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 4.602531] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 4.610182] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.622381] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 4.631351] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 4.638519] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 4.649279] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 4.658520] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 4.665909] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 4.679561] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 4.692346] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.699907] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 4.711393] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 4.719108] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.731363] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 4.740197] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 4.747409] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 4.758153] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 4.767376] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 4.774762] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 4.785426] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.793065] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 4.804482] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 4.812162] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.824165] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 4.833050] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 4.840206] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 4.851011] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 4.860190] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 4.867570] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 4.880524] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 4.888466] hctosys: unable to open rtc device (rtc0) <6>[ 4.898396] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 4.906144] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 4.917887] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 4.925604] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.937695] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 4.946591] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 4.953800] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 4.964551] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 4.973786] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 4.981169] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.033569] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 5.050076] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 8.182945] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 8.201023] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.231738] Sending DHCP requests ., OK <6>[ 8.275493] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.33 <6>[ 8.284001] IP-Config: Complete: <6>[ 8.287550] device=eth0, hwaddr=00:19:b8:08:f1:13, ipaddr=192.168.201.33, mask=255.255.255.0, gw=192.168.201.1 <6>[ 8.298397] host=imx6q-sabrelite-lava-cbg-3, domain=lava-rack, nis-domain=(none) <6>[ 8.306635] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 8.306650] nameserver0=192.168.201.1 <6>[ 8.362059] Freeing unused kernel memory: 2048K <6>[ 8.381499] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 11.295074] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.307030] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.318821] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.332073] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 11.340355] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 11.344296] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.358404] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <4>[ 11.361698] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.375245] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.383684] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.395597] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 11.406808] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.409890] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.416084] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.422739] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 11.430180] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 11.446976] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.454720] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.466505] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.474355] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 11.486902] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.495953] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.503318] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 11.550029] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.550595] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 11.559612] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.573564] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 11.582186] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 11.589378] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 11.598591] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.606528] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.613808] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 11.624068] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.631974] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 11.639596] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 11.644511] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.656479] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.663993] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 11.675675] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 11.682549] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 11.691917] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 1 <4>[ 11.703032] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.712468] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.721181] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 11.732141] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 11.739895] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 11.752019] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 11.759760] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 11.772552] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 11.781481] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 11.788703] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 11.800155] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 11.809511] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 11.816957] panel-simple panel-lvds0: Dropping the link to regulator.0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:13 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.33 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-3 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 13.617374] systemd[1]: System time before build time, advancing clock. <3>[ 13.695319] cgroup: cgroup2: unknown option "memory_recursiveprot" <30>[ 13.735623] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 13.761789] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 13.806006] systemd[1]: Set hostname to . <30>[ 15.219648] systemd[1]: Queued start job for default target Graphical Interface. <5>[ 15.230373] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 15.240587] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <5>[ 15.281895] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 15.292909] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <5>[ 15.331396] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 15.340064] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 15.384665] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 15.424874] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 15.474123] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 15.522477] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 15.536148] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 15.571736] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 15.612740] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 15.652372] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 15.691574] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 15.734835] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 15.837405] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 15.849126] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 15.897235] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 15.946986] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 16.001652] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 16.046171] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 16.094568] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 16.105383] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 16.125376] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 16.173868] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <5>[ 16.252682] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 16.281733] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <5>[ 16.321809] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 16.337250] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <5>[ 16.373144] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 16.387889] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 16.431058] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 16.481140] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <6>[ 16.487593] fuse init (API version 7.27) <30>[ 16.515894] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 16.568633] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 16.614169] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 16.661417] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 16.709888] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 16.754087] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 16.798759] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 16.873897] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 16.883426] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 16.926389] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 16.935544] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. <30>[ 16.976877] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 16.986511] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. <30>[ 17.025957] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. <30>[ 17.065889] systemd[1]: Finished Remount Root and Kernel File Systems. [ OK ] Finished Remount Root and Kernel File Systems. <30>[ 17.112372] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... <30>[ 17.158733] systemd[1]: Mounting Kernel Configuration File System... Mounting Kernel Configuration File System... <30>[ 17.206835] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. <30>[ 17.216718] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. <30>[ 17.234233] systemd[1]: Starting Load/Save Random Seed... Starting Load/Save Random Seed... <5>[ 17.271678] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 17.286876] systemd[1]: Starting Apply Kernel Variables... <5>[ 17.292195] random: systemd-journal: uninitialized urandom read (16 bytes read) Starting Apply Kernel Variables... <5>[ 17.333268] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 17.347660] systemd[1]: Starting Create System Users... Starting Create System Users... <30>[ 17.386115] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. Starting Flush Journal to Persistent Storage... [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... <46>[ 17.644839] systemd-journald[166]: Received client request to flush runtime journal. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Rule-based Manage…for Device Events and Files... <5>[ 18.841727] random: crng init done <5>[ 18.845558] random: 45 urandom warning(s) missed due to ratelimiting [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Started User Login Management. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.304-cip106 #1 SMP Tue Feb 6 22:18:03 UTC 2024 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12709778/extract-nfsrootfs-alvixms7' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12709778/extract-nfsrootfs-alvixms7' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-12709778/environment . /lava-12709778/environment / # /lava-12709778/bin/lava-test-runner /lava-12709778/0 /lava-12709778/bin/lava-test-runner /lava-12709778/0 <6>[ 38.912571] usb_otg_vbus: disabling <6>[ 38.916551] CAN XCVR: disabling + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-12709778/0/tests/0_timesync-off ++ cat uuid + UUID=12709778_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-seccomp + TESTRUN_ID=1_kselftest-seccomp + cd /lava-12709778/0/tests/1_kselftest-seccomp ++ cat uuid + UUID=12709778_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c seccomp -T '' -t kselftest_armhf.tar.gz -s True -u None -L '' -S /dev/null -b imx6q-sabrelite -g cip -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2024-02-06 22:33:53-- http://none/ Resolving none (none)... failed: Name or service not known. wget: unable to resolve host address 'none' tar: None: Cannot open: No such file or directory tar: Error is not recoverable: exiting now ./kselftest.sh: 160: cd: can't cd to kselftest / #