Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.4 (4 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 1075573/tftp-deploy-_ayfou1g/kernel/zImage tftp 0x82000000 1075573/tftp-deploy-_ayfou1g/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1075573/tftp-deploy-_ayfou1g/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################ 5.3 MiB/s done Bytes transferred = 4512648 (44db88 hex) => tftp 0x83000000 1075573/tftp-deploy-_ayfou1g/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1075573/tftp-deploy-_ayfou1g/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1075573/tftp-deploy-_ayfou1g/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################################### 5.2 MiB/s done Bytes transferred = 9441213 (900fbd hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1075573/tftp-deploy-_ayfou1g/dtb/am335x-boneblack.dtb tftp 0x88000000 1075573/tftp-deploy-_ayfou1g/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1075573/tftp-deploy-_ayfou1g/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *### 4.2 MiB/s done Bytes transferred = 34893 (884d hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/1075573/extract-nfsrootfs-31jrbjbn,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/1075573/extract-nfsrootfs-31jrbjbn,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2024-01-13 10:08:01 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9441149 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8800b84c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.304-cip106 (KernelCI@build-j76563-arm-gcc-10-omap2plus-defconfig-wm9hh) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Sat Jan 13 09:46:46 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 17 pages/cpu s38632 r8192 d22808 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/1075573/extract-nfsrootfs-31jrbjbn,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) <6>[ 0.000000] Memory: 469760K/522240K available (9216K kernel code, 794K rwdata, 2604K rodata, 1024K init, 7477K bss, 36096K reserved, 16384K cma-reserved, 0K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xdfe00000 ( 510 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (10208 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 795 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7478 kB) <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz <6>[ 0.000019] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008367] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018169] OMAP clocksource: timer1 at 24000000 Hz <2>[ 0.023950] timer_probe: no matching timers found <6>[ 0.030410] Console: colour dummy device 80x30 <3>[ 0.035313] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042360] This ensures that you still see kernel messages. Please <3>[ 0.049112] update your kernel commandline. <4>[ 0.053690] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.061957] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.066444] ... MAX_LOCK_DEPTH: 48 <4>[ 0.071046] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.075801] ... CLASSHASH_SIZE: 4096 <4>[ 0.080580] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.085424] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.090294] ... CHAINHASH_SIZE: 32768 <4>[ 0.095138] memory used by lock dependency info: 4655 kB <4>[ 0.100991] per task-struct memory footprint: 1536 bytes <6>[ 0.106862] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.145390] CPU: Testing write buffer coherency: ok <6>[ 0.150906] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.156379] pid_max: default: 32768 minimum: 301 <6>[ 0.161827] Security Framework initialized <6>[ 0.166432] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.173567] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.185992] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.194139] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.201909] rcu: Hierarchical SRCU implementation. <6>[ 0.208762] smp: Bringing up secondary CPUs ... <6>[ 0.213713] smp: Brought up 1 node, 1 CPU <6>[ 0.218113] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.224886] CPU: All CPU(s) started in SVC mode. <6>[ 0.233872] devtmpfs: initialized <6>[ 0.262461] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.271484] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.282015] futex hash table entries: 256 (order: 2, 16384 bytes) <6>[ 0.290225] pinctrl core: initialized pinctrl subsystem <6>[ 0.301458] NET: Registered protocol family 16 <6>[ 0.312969] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.382205] l4_wkup_cm:clk:0010:0: failed to disable <6>[ 0.429751] audit: initializing netlink subsys (disabled) <6>[ 0.438795] cpuidle: using governor menu <5>[ 0.456522] audit: type=2000 audit(0.410:1): state=initialized audit_enabled=0 res=1 <6>[ 0.466302] OMAP GPIO hardware version 0.1 <6>[ 0.495859] No ATAGs? <6>[ 0.495874] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 0.540974] edma 49000000.edma: TI EDMA DMA engine driver <6>[ 0.553285] vgaarb: loaded <5>[ 0.557386] SCSI subsystem initialized <6>[ 0.564133] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.569663] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.579437] PTP clock support registered <6>[ 0.587732] clocksource: Switched to clocksource timer1 <5>[ 0.748292] VFS: Disk quotas dquot_6.6.0 <6>[ 0.752804] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 0.786465] NET: Registered protocol family 2 <6>[ 0.792069] IP idents hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.801152] tcp_listen_portaddr_hash hash table entries: 256 (order: 1, 10240 bytes) <6>[ 0.809636] TCP established hash table entries: 4096 (order: 2, 16384 bytes) <6>[ 0.817240] TCP bind hash table entries: 4096 (order: 5, 147456 bytes) <6>[ 0.824839] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.832130] UDP hash table entries: 256 (order: 2, 20480 bytes) <6>[ 0.838689] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) <6>[ 0.846033] NET: Registered protocol family 1 <6>[ 0.853801] RPC: Registered named UNIX socket transport module. <6>[ 0.860422] RPC: Registered udp transport module. <6>[ 0.865543] RPC: Registered tcp transport module. <6>[ 0.870727] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.879630] Trying to unpack rootfs image as initramfs... <6>[ 1.694554] Freeing initrd memory: 9220K <6>[ 1.701025] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 1.715365] Initialise system trusted keyrings <6>[ 1.721640] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 1.732154] NFS: Registering the id_resolver key type <5>[ 1.737998] Key type id_resolver registered <5>[ 1.742630] Key type id_legacy registered <6>[ 1.747223] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 1.763195] Key type asymmetric registered <5>[ 1.768169] Asymmetric key parser 'x509' registered <6>[ 1.773632] io scheduler noop registered <6>[ 1.778061] io scheduler deadline registered <6>[ 1.782903] io scheduler cfq registered (default) <6>[ 1.788102] io scheduler mq-deadline registered <6>[ 1.793044] io scheduler kyber registered <6>[ 1.800290] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 1.814673] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 1.834536] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 30, base_baud = 3000000) is a 8250 <6>[ 1.844656] console [ttyS0] enabled <6>[ 1.844656] console [ttyS0] enabled <6>[ 1.852449] bootconsole [omap8250] disabled <6>[ 1.852449] bootconsole [omap8250] disabled <6>[ 1.893050] brd: module loaded <6>[ 1.918810] loop: module loaded <3>[ 1.924898] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 2.007714] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 2.015736] davinci_mdio 4a101000.mdio: detected phy mask fffffffe <6>[ 2.053870] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 2.064950] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 2.072577] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 2.079448] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 2.085042] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 2.095960] i2c /dev entries driver <6>[ 2.103667] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.110743] sdhci: Copyright(c) Pierre Ossman <6>[ 2.116817] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 2.125987] omap_hsmmc 48060000.mmc: Got CD GPIO <6>[ 2.132987] omap_hsmmc 48060000.mmc: Linked as a consumer to regulator.1 <6>[ 2.170665] omap_hsmmc 481d8000.mmc: Linked as a consumer to regulator.1 <6>[ 2.202705] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.209438] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.218852] oprofile: using arm/armv7 <6>[ 2.223713] Initializing XFRM netlink socket <6>[ 2.229126] NET: Registered protocol family 10 <6>[ 2.238637] Segment Routing with IPv6 <6>[ 2.242774] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.251050] NET: Registered protocol family 17 <6>[ 2.255873] NET: Registered protocol family 15 <5>[ 2.261147] Key type dns_resolver registered <6>[ 2.265855] ThumbEE CPU extension supported. <5>[ 2.270549] Registering SWP/SWPB emulation handler <3>[ 2.275645] omap_voltage_late_init: Voltage driver support not added <3>[ 2.282416] sr_dev_init: Unknown instance smartreflex0 <6>[ 2.288364] SmartReflex Class3 initialized <5>[ 2.296016] Loading compiled-in X.509 certificates <6>[ 2.395339] mmc1: new high speed MMC card at address 0001 <6>[ 2.406392] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 2.413122] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 2.420969] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 2.429555] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (248:0) <6>[ 2.447460] mmcblk1: p1 <6>[ 2.465671] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 2.472577] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 2.482674] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 2.490565] hctosys: unable to open rtc device (rtc0) <4>[ 2.495937] sr_init: No PMIC hook to init smartreflex <6>[ 2.520349] net eth0: initializing cpsw version 1.12 (0) <6>[ 2.629020] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 2.652384] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 5.788789] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 5.807786] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.837658] Sending DHCP requests ., OK <6>[ 5.881829] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.4 <6>[ 5.889991] IP-Config: Complete: <6>[ 5.893514] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.4, mask=255.255.255.0, gw=192.168.11.1 <6>[ 5.904108] host=192.168.11.4, domain=usen.ad.jp, nis-domain=(none) <6>[ 5.911165] bootserver=0.0.0.0, rootserver=192.168.11.5, rootpath= <6>[ 5.911171] nameserver0=192.168.11.1 <6>[ 5.928588] Freeing unused kernel memory: 1024K <6>[ 5.938443] Run /init as init process Loading, please wait... Starting systemd-udevd version 252.12-1~deb12u1 <6>[ 7.709242] cpu cpu0: Linked as a consumer to regulator.3 <6>[ 7.715496] cpu cpu0: Dropping the link to regulator.3 <6>[ 7.822764] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 7.849288] cpu cpu0: Linked as a consumer to regulator.3 <6>[ 7.862653] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 7.908172] omap_rtc 44e3e000.rtc: registered as rtc0 <4>[ 7.930384] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <6>[ 7.999501] input: tps65217_pwrbutton as /devices/platform/ocp/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <6>[ 8.016792] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <6>[ 8.257472] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 8.265679] random: crng init done <6>[ 8.415000] tda998x 0-0070: found TDA19988 <6>[ 8.506389] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_ops [tda998x]) <6>[ 8.514761] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 8.521788] [drm] No driver support for vblank timestamp query. <4>[ 8.594772] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator <6>[ 8.605639] am335x-phy-driver 47401300.usb-phy: Linked as a consumer to regulator.0 <6>[ 8.634316] usbcore: registered new interface driver usbfs <6>[ 8.641065] usbcore: registered new interface driver hub <6>[ 8.646876] usbcore: registered new device driver usb <6>[ 8.828595] [drm] Cannot find any crtc or sizes <6>[ 8.869074] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <4>[ 8.891095] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator <6>[ 8.901914] am335x-phy-driver 47401b00.usb-phy: Linked as a consumer to regulator.0 <6>[ 9.076312] remoteproc remoteproc0: wkup_m3 is available <6>[ 9.096992] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.104130] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.220559] remoteproc remoteproc0: powering up wkup_m3 <4>[ 9.227250] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 9.237974] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 9.244213] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 9.251128] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 <6>[ 9.260121] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.267729] usb usb1: Product: MUSB HDRC host driver <6>[ 9.272992] usb usb1: Manufacturer: Linux 4.19.304-cip106 musb-hcd <6>[ 9.279527] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 9.599703] hub 1-0:1.0: USB hub found <6>[ 9.642665] hub 1-0:1.0: 1 port detected <6>[ 9.871397] [drm] Cannot find any crtc or sizes <6>[ 9.916470] asoc-simple-card sound: i2s-hifi <-> 48038000.mcasp mapping ok Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... done. Begin: Waiting up to 180 secs for any network device to become available ... done. IP-Config: eth0 hardware address 64:cf:d9:3f:a0:d5 mtu 1500 DHCP IP-Config: eth0 guessed broadcast address 192.168.11.255 IP-Config: eth0 complete (dhcp from 192.168.11.1): address: 192.168.11.4 broadcast: 192.168.11.255 netmask: 255.255.255.0 gateway: 192.168.11.1 dns0 : 192.168.11.1 dns1 : 0.0.0.0 domain : usen.ad.jp rootserver: 192.168.11.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... mount: No such file or directory mount: invalid option -- done. mount: No such file or directory run-init: opening console: No such file or directory Target filesystem doesn't have requested /sbin/init. run-init: opening console: No such file or directory run-init: opening console: No such file or directory run-init: opening console: No such file or directory run-init: opening console: No such file or directory run-init: opening console: No such file or directory No init found. Try passing init= bootarg. (initramfs) <6>[ 64.514524] platform pm33xx: deferred probe pending