[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.33 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12799789/tftp-deploy-h0ahyp3c/kernel/zImage tftp 0x10000000 12799789/tftp-deploy-h0ahyp3c/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '12799789/tftp-deploy-h0ahyp3c/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 14 MiB/s done Bytes transferred = 8733184 (854200 hex) => tftp 0x14000000 12799789/tftp-deploy-h0ahyp3c/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12799789/tftp-deploy-h0ahyp3c/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '12799789/tftp-deploy-h0ahyp3c/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################### 14 MiB/s done Bytes transferred = 9414689 (8fa821 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12799789/tftp-deploy-h0ahyp3c/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12799789/tftp-deploy-h0ahyp3c/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '12799789/tftp-deploy-h0ahyp3c/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4.4 MiB/s done Bytes transferred = 41822 (a35e hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12799789/extract-nfsrootfs-2wsynrq5,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12799789/extract-nfsrootfs-2wsynrq5,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x854200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9414625 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d35d Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.306-cip107 (KernelCI@build-j113472-arm-gcc-10-multi-v7-defconfig-246jr) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Mon Feb 19 05:23:24 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12799789/extract-nfsrootfs-2wsynrq5,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 942968K/1048576K available (12288K kernel code, 1597K rwdata, 4688K rodata, 2048K init, 394K bss, 40072K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021307] Console: colour dummy device 80x30 <6>[ 0.023189] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033605] CPU: Testing write buffer coherency: ok <6>[ 0.038739] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044036] pid_max: default: 32768 minimum: 301 <6>[ 0.049040] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.055804] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.063962] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069714] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077427] rcu: Hierarchical SRCU implementation. <6>[ 0.083950] EFI services will not be available. <6>[ 0.086202] smp: Bringing up secondary CPUs ... <6>[ 0.091460] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091467] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.102818] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.102825] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114005] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114011] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124457] smp: Brought up 1 node, 4 CPUs <6>[ 0.128713] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135129] CPU: All CPU(s) started in SVC mode. <6>[ 0.141081] devtmpfs: initialized <6>[ 0.150579] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156033] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.165781] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175314] pinctrl core: initialized pinctrl subsystem <6>[ 0.179611] DMI not present or invalid. <6>[ 0.182839] NET: Registered protocol family 16 <6>[ 0.190217] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.196834] cpuidle: using governor menu <6>[ 0.198882] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.213872] vdd1p1: supplied by regulator-dummy <6>[ 0.216342] vdd3p0: supplied by regulator-dummy <6>[ 0.221071] vdd2p5: supplied by regulator-dummy <6>[ 0.225902] vddarm: supplied by regulator-dummy <6>[ 0.230826] vddpu: supplied by regulator-dummy <6>[ 0.235224] vddsoc: supplied by regulator-dummy <6>[ 0.253979] No ATAGs? <6>[ 0.254124] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.262086] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.271600] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278483] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290418] Serial: AMBA PL011 UART driver <6>[ 0.294262] console [pstore-1] enabled <6>[ 0.296110] pstore: Registered ramoops as persistent store backend <6>[ 0.302363] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.330920] mxs-dma 110000.dma-apbh: initialized <6>[ 0.340426] vgaarb: loaded <5>[ 0.341342] SCSI subsystem initialized <6>[ 0.344948] usbcore: registered new interface driver usbfs <6>[ 0.350407] usbcore: registered new interface driver hub <6>[ 0.355905] usbcore: registered new device driver usb <6>[ 0.362401] i2c i2c-0: IMX I2C adapter registered <6>[ 0.366143] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.372254] i2c i2c-1: IMX I2C adapter registered <6>[ 0.376667] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.382609] i2c i2c-2: IMX I2C adapter registered <6>[ 0.387197] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.394307] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.397975] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.407385] PTP clock support registered <6>[ 0.411763] EDAC MC: Ver: 3.0.0 <6>[ 0.417776] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.481605] NET: Registered protocol family 2 <6>[ 0.483796] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.491345] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.498320] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.505637] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.512426] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.519095] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.525083] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.531848] NET: Registered protocol family 1 <6>[ 0.536818] RPC: Registered named UNIX socket transport module. <6>[ 0.542478] RPC: Registered udp transport module. <6>[ 0.547404] RPC: Registered tcp transport module. <6>[ 0.552382] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.559555] Trying to unpack rootfs image as initramfs... <6>[ 1.284104] Freeing initrd memory: 9196K <4>[ 1.285980] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.293199] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.303172] Initialise system trusted keyrings <6>[ 1.306165] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.318626] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.322506] NFS: Registering the id_resolver key type <5>[ 1.327221] Key type id_resolver registered <5>[ 1.331641] Key type id_legacy registered <6>[ 1.335917] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.342747] Key type asymmetric registered <5>[ 1.344841] Asymmetric key parser 'x509' registered <6>[ 1.350037] bounce: pool size: 64 pages <6>[ 1.354097] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.361735] io scheduler noop registered <6>[ 1.365895] io scheduler deadline registered <6>[ 1.370561] io scheduler cfq registered (default) <6>[ 1.375378] io scheduler mq-deadline registered <6>[ 1.380177] io scheduler kyber registered <6>[ 1.406490] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.411033] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.418151] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.425439] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.445697] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.449137] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.456911] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.463146] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.471006] PU : no governor for states <4>[ 1.471090] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 1.474967] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.484725] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.555350] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.562658] SuperH (H)SCI(F) driver initialized <6>[ 1.565505] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.574272] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.585235] console [ttymxc1] enabled <6>[ 1.585235] console [ttymxc1] enabled <6>[ 1.590235] bootconsole [ec_imx21] disabled <6>[ 1.590235] bootconsole [ec_imx21] disabled <6>[ 1.600291] msm_serial: driver initialized <6>[ 1.606544] STMicroelectronics ASC driver initialized <6>[ 1.613725] STM32 USART driver initialized <4>[ 1.628961] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 1.637631] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 1.644624] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 1.651401] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 1.660434] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 1.667552] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 1.682171] brd: module loaded <6>[ 1.692112] loop: module loaded <6>[ 1.698782] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 1.706975] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 1.715275] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 1.723736] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 1.734522] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 1.741806] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 1.750884] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 1.761673] scsi host0: ahci-imx <6>[ 1.765728] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 1.784688] CAN device driver interface <6>[ 1.790092] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 1.797152] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 1.806113] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 1.815206] pps pps0: new PPS source ptp0 <6>[ 1.837056] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 1.844480] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 1.850599] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.856837] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 1.864081] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.875788] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 1.883515] usbcore: registered new interface driver pegasus <6>[ 1.889496] usbcore: registered new interface driver asix <6>[ 1.895193] usbcore: registered new interface driver ax88179_178a <6>[ 1.901604] usbcore: registered new interface driver cdc_ether <6>[ 1.907779] usbcore: registered new interface driver smsc75xx <6>[ 1.913838] usbcore: registered new interface driver smsc95xx <6>[ 1.919902] usbcore: registered new interface driver net1080 <6>[ 1.925859] usbcore: registered new interface driver cdc_subset <6>[ 1.932090] usbcore: registered new interface driver zaurus <6>[ 1.938014] usbcore: registered new interface driver cdc_ncm <6>[ 1.946862] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.953686] ehci-pci: EHCI PCI platform driver <6>[ 1.958460] ehci-platform: EHCI generic platform driver <6>[ 1.964239] ehci-orion: EHCI orion driver <6>[ 1.968759] SPEAr-ehci: EHCI SPEAr driver <6>[ 1.973224] ehci-st: EHCI STMicroelectronics driver <6>[ 1.978578] ehci-exynos: EHCI EXYNOS driver <6>[ 1.983212] ehci-atmel: EHCI Atmel driver <6>[ 1.987664] tegra-ehci: Tegra EHCI driver <6>[ 1.992173] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.998653] ohci-pci: OHCI PCI platform driver <6>[ 2.003405] ohci-platform: OHCI generic platform driver <6>[ 2.009187] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.013654] ohci-st: OHCI STMicroelectronics driver <6>[ 2.019003] ohci-atmel: OHCI Atmel driver <6>[ 2.024272] usbcore: registered new interface driver usb-storage <6>[ 2.032868] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.044853] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.055001] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.060205] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.087804] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.094139] hub 1-0:1.0: USB hub found <6>[ 2.098219] hub 1-0:1.0: 1 port detected <6>[ 2.099308] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.108133] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.108705] i2c /dev entries driver <6>[ 2.114672] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.132856] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.144184] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.150657] sdhci: Copyright(c) Pierre Ossman <6>[ 2.157537] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.165807] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.172613] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.178067] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.183561] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.221530] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.229552] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.235088] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.274961] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.286340] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.293612] usbcore: registered new interface driver usbhid <6>[ 2.299474] usbhid: USB HID core driver <6>[ 2.309485] NET: Registered protocol family 10 <6>[ 2.315346] Segment Routing with IPv6 <6>[ 2.319385] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.326109] NET: Registered protocol family 17 <6>[ 2.326531] mmc0: new high speed SDHC card at address aaaa <6>[ 2.330857] can: controller area network core (rev 20170425 abi 9) <6>[ 2.338332] mmcblk0: mmc0:aaaa SL16G 14.8 GiB <6>[ 2.343170] NET: Registered protocol family 29 <6>[ 2.352504] can: raw protocol (rev 20170425) <6>[ 2.357044] can: broadcast manager protocol (rev 20170425 t) <4>[ 2.361384] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 2.362998] can: netlink gateway (rev 20170425) max_hops=1 <4>[ 2.370666] GPT:7812499 != 31116287 <5>[ 2.376842] Key type dns_resolver registered <4>[ 2.380167] GPT:Alternate GPT header not at the end of the disk. <4>[ 2.390995] GPT:7812499 != 31116287 <6>[ 2.391912] cpu cpu0: Linked as a consumer to regulator.4 <4>[ 2.394754] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.400495] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.405879] mmcblk0: p1 p2 p3 <6>[ 2.411567] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.414965] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.421324] ThumbEE CPU extension supported. <5>[ 2.431841] Registering SWP/SWPB emulation handler <5>[ 2.437411] Loading compiled-in X.509 certificates <6>[ 2.443918] pstore: Using compression: deflate <6>[ 2.461940] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.469370] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.477948] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.485397] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.494036] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.502715] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.509671] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.517482] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.526507] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.533627] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.542142] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.552613] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.560001] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.568291] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.575732] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.584304] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.592976] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.599927] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.607686] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.616701] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.623826] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.630970] hub 1-1:1.0: USB hub found <6>[ 2.631614] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.635115] hub 1-1:1.0: 3 ports detected <6>[ 2.642379] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.654884] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.662349] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.670884] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.679560] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.686503] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.694268] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.703295] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.710415] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.718088] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.725442] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.734294] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 2.741199] hctosys: unable to open rtc device (rtc0) <6>[ 2.747677] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.755200] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.764248] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.772934] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.779890] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.787824] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.796838] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.803962] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.811696] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.819067] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.878443] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 2.893393] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 5.998419] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.017811] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.047855] Sending DHCP requests ., OK <6>[ 6.092006] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.33 <6>[ 6.100354] IP-Config: Complete: <6>[ 6.103873] device=eth0, hwaddr=00:19:b8:08:f1:13, ipaddr=192.168.201.33, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.114624] host=imx6q-sabrelite-lava-cbg-3, domain=lava-rack, nis-domain=(none) <6>[ 6.122767] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.122775] nameserver0=192.168.201.1 <6>[ 6.141655] Freeing unused kernel memory: 2048K <6>[ 6.178135] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 6.994472] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.006613] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.010099] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.014144] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.029681] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.038395] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.044843] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.045882] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.053122] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.060529] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.066818] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <4>[ 7.075159] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.088879] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.096038] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.104198] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.111627] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.120395] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.127886] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.137092] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.145911] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.152917] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.177135] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.184496] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.192501] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.196399] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.200178] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.212788] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 7.220503] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.221301] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.232533] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.242300] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.244168] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.250060] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.266813] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.275523] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.282669] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.291132] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.300196] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.307672] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.315902] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.323608] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.332379] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.340026] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.349513] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.358243] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.365484] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.375342] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.381780] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.389489] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <4>[ 7.399275] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.408398] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.416618] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.424922] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.432536] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.441582] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.449150] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.458750] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.467503] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.474548] panel-simple panel-lcd: Dropping the link to regulator.0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:13 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.33 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-3 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 8.403628] systemd[1]: System time before build time, advancing clock. <3>[ 8.433894] cgroup: cgroup2: unknown option "memory_recursiveprot" <30>[ 8.448444] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 8.472418] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 8.510290] systemd[1]: Set hostname to . <30>[ 9.295670] systemd[1]: Queued start job for default target Graphical Interface. <5>[ 9.305494] random: systemd: uninitialized urandom read (16 bytes read) <28>[ 9.312585] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 9.325397] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 9.334899] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <5>[ 9.368161] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 9.376185] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <5>[ 9.418060] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 9.426051] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 9.469035] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 9.508295] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 9.548640] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 9.588869] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 9.601481] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 9.638870] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 9.668314] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 9.708285] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 9.738475] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 9.769060] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 9.845432] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 9.855740] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 9.899565] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 9.940589] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 9.980913] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 10.019470] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 10.059214] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 10.068749] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 10.081037] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 10.121782] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 10.163576] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 10.211476] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 10.252982] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 10.290876] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 10.332413] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <5>[ 10.342697] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.352423] systemd[1]: Starting Journal Service... Starting Journal Service... <5>[ 10.393224] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.403240] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <5>[ 10.438216] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.447925] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 10.491318] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 10.532777] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 10.568688] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 10.609197] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 10.672624] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply <46>[ 10.982503] systemd-journald[166]: Received client request to flush runtime journal. Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. <5>[ 11.398827] random: systemd: uninitialized urandom read (16 bytes read) Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. <5>[ 11.478985] random: systemd-journal: uninitialized urandom read (16 bytes read) <5>[ 11.490618] random: systemd-journal: uninitialized urandom read (16 bytes read) [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... <5>[ 11.917984] random: crng init done <5>[ 11.921678] random: 48 urandom warning(s) missed due to ratelimiting [ OK ] Finished Load/Save Random Seed. [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Create Volatile Files and Directories. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.306-cip107 #1 SMP Mon Feb 19 05:23:24 UTC 2024 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12799789/extract-nfsrootfs-2wsynrq5' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12799789/extract-nfsrootfs-2wsynrq5' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-12799789/environment . /lava-12799789/environment / # /lava-12799789/bin/lava-test-runner /lava-12799789/0 /lava-12799789/bin/lava-test-runner /lava-12799789/0 + export TESTRUN_ID=0_dmesg + cd /lava-12799789/0/tests/0_dmesg + cat uuid + UUID=12799789_1.6.2.4.1 + set +<8>[ 24.802211] x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 24.876481] <8>[ 24.937513] <8>[ 24.999456] + set +x <8>[ 25.008990] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-12799789/environment / # . /lava-12799789/environment/lava-12799789/bin/lava-test-runner /lava-12799789/1 / # /lava-12799789/bin/lava-test-runner /lava-12799789/1 + export TESTRUN_ID=1_bootrr + cd /lava-12799789/1/tests/1_bootrr + cat uuid + UUID=12799789_1.6.2.4.5 + set +<8>[ 25.557398] x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-12799789/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds panel-lcd /lava-12799789/1/../bin/lava-test-case <8>[ 26.678658] /lava-12799789/1/../bin/lava-test-case <8>[ 26.750958] /lava-12799789/1/../bin/lava-test-case <8>[ 26.784066] + set +x <8>[ 26.809613] / #