Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.2 (4 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 1095546/tftp-deploy-6o18t_pr/kernel/zImage tftp 0x82000000 1095546/tftp-deploy-6o18t_pr/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '1095546/tftp-deploy-6o18t_pr/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################ 5.1 MiB/s done Bytes transferred = 4508736 (44cc40 hex) => tftp 0x83000000 1095546/tftp-deploy-6o18t_pr/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1095546/tftp-deploy-6o18t_pr/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '1095546/tftp-deploy-6o18t_pr/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################### 5.2 MiB/s done Bytes transferred = 12685387 (c1904b hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1095546/tftp-deploy-6o18t_pr/dtb/am335x-boneblack.dtb tftp 0x88000000 1095546/tftp-deploy-6o18t_pr/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '1095546/tftp-deploy-6o18t_pr/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *### 4.2 MiB/s done Bytes transferred = 34893 (884d hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2024-02-19 8:37:17 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12685323 Bytes = 12.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8800b84c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.306-cip107 (KernelCI@build-j113430-arm-gcc-10-omap2plus-defconfig-gsztb) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Mon Feb 19 05:17:06 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 17 pages/cpu s38632 r8192 d22808 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) <6>[ 0.000000] Memory: 466588K/522240K available (9216K kernel code, 794K rwdata, 2600K rodata, 1024K init, 7477K bss, 39268K reserved, 16384K cma-reserved, 0K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xdfe00000 ( 510 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (10208 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 795 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7478 kB) <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz <6>[ 0.000018] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008369] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018169] OMAP clocksource: timer1 at 24000000 Hz <2>[ 0.023942] timer_probe: no matching timers found <6>[ 0.030379] Console: colour dummy device 80x30 <3>[ 0.035279] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042331] This ensures that you still see kernel messages. Please <3>[ 0.049083] update your kernel commandline. <4>[ 0.053661] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.061928] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.066415] ... MAX_LOCK_DEPTH: 48 <4>[ 0.071017] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.075772] ... CLASSHASH_SIZE: 4096 <4>[ 0.080552] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.085396] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.090265] ... CHAINHASH_SIZE: 32768 <4>[ 0.095109] memory used by lock dependency info: 4655 kB <4>[ 0.100961] per task-struct memory footprint: 1536 bytes <6>[ 0.106831] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.145377] CPU: Testing write buffer coherency: ok <6>[ 0.150883] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.156357] pid_max: default: 32768 minimum: 301 <6>[ 0.161808] Security Framework initialized <6>[ 0.166415] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.173551] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.185950] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.194060] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.201824] rcu: Hierarchical SRCU implementation. <6>[ 0.208557] smp: Bringing up secondary CPUs ... <6>[ 0.213596] smp: Brought up 1 node, 1 CPU <6>[ 0.217999] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.224762] CPU: All CPU(s) started in SVC mode. <6>[ 0.233725] devtmpfs: initialized <6>[ 0.261876] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.270880] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.281403] futex hash table entries: 256 (order: 2, 16384 bytes) <6>[ 0.289698] pinctrl core: initialized pinctrl subsystem <6>[ 0.300859] NET: Registered protocol family 16 <6>[ 0.312423] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.380596] l4_wkup_cm:clk:0010:0: failed to disable <6>[ 0.428045] audit: initializing netlink subsys (disabled) <6>[ 0.436999] cpuidle: using governor menu <5>[ 0.454746] audit: type=2000 audit(0.400:1): state=initialized audit_enabled=0 res=1 <6>[ 0.464511] OMAP GPIO hardware version 0.1 <6>[ 0.493867] No ATAGs? <6>[ 0.493882] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 0.538132] edma 49000000.edma: TI EDMA DMA engine driver <6>[ 0.550704] vgaarb: loaded <5>[ 0.554809] SCSI subsystem initialized <6>[ 0.561528] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.566925] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.576780] PTP clock support registered <6>[ 0.584998] clocksource: Switched to clocksource timer1 <5>[ 0.742974] VFS: Disk quotas dquot_6.6.0 <6>[ 0.747641] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 0.780934] NET: Registered protocol family 2 <6>[ 0.786530] IP idents hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.795662] tcp_listen_portaddr_hash hash table entries: 256 (order: 1, 10240 bytes) <6>[ 0.804002] TCP established hash table entries: 4096 (order: 2, 16384 bytes) <6>[ 0.811715] TCP bind hash table entries: 4096 (order: 5, 147456 bytes) <6>[ 0.819303] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.826583] UDP hash table entries: 256 (order: 2, 20480 bytes) <6>[ 0.833046] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) <6>[ 0.840457] NET: Registered protocol family 1 <6>[ 0.848181] RPC: Registered named UNIX socket transport module. <6>[ 0.854610] RPC: Registered udp transport module. <6>[ 0.859916] RPC: Registered tcp transport module. <6>[ 0.865102] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.873937] Trying to unpack rootfs image as initramfs... <6>[ 2.065942] Freeing initrd memory: 12392K <6>[ 2.072501] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 2.086955] Initialise system trusted keyrings <6>[ 2.093136] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 2.103374] NFS: Registering the id_resolver key type <5>[ 2.109204] Key type id_resolver registered <5>[ 2.113835] Key type id_legacy registered <6>[ 2.118715] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 2.134405] Key type asymmetric registered <5>[ 2.139387] Asymmetric key parser 'x509' registered <6>[ 2.144957] io scheduler noop registered <6>[ 2.149281] io scheduler deadline registered <6>[ 2.154122] io scheduler cfq registered (default) <6>[ 2.159331] io scheduler mq-deadline registered <6>[ 2.164272] io scheduler kyber registered <6>[ 2.171430] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 2.185914] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 2.205445] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 30, base_baud = 3000000) is a 8250 <6>[ 2.215336] console [ttyS0] enabled <6>[ 2.215336] console [ttyS0] enabled <6>[ 2.223016] bootconsole [omap8250] disabled <6>[ 2.223016] bootconsole [omap8250] disabled <6>[ 2.263670] brd: module loaded <6>[ 2.289427] loop: module loaded <3>[ 2.295642] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 2.374994] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 2.383016] davinci_mdio 4a101000.mdio: detected phy mask fffffffe <6>[ 2.425543] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 2.436460] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 2.444146] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 2.451062] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 2.456739] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 2.467603] i2c /dev entries driver <6>[ 2.475334] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.481838] sdhci: Copyright(c) Pierre Ossman <6>[ 2.487959] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 2.497533] omap_hsmmc 48060000.mmc: Got CD GPIO <6>[ 2.504202] omap_hsmmc 48060000.mmc: Linked as a consumer to regulator.1 <6>[ 2.541607] omap_hsmmc 481d8000.mmc: Linked as a consumer to regulator.1 <6>[ 2.573605] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.580344] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.589683] oprofile: using arm/armv7 <6>[ 2.594518] Initializing XFRM netlink socket <6>[ 2.599955] NET: Registered protocol family 10 <6>[ 2.609621] Segment Routing with IPv6 <6>[ 2.613761] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.622154] NET: Registered protocol family 17 <6>[ 2.627140] NET: Registered protocol family 15 <5>[ 2.632290] Key type dns_resolver registered <6>[ 2.637088] ThumbEE CPU extension supported. <5>[ 2.641682] Registering SWP/SWPB emulation handler <3>[ 2.646895] omap_voltage_late_init: Voltage driver support not added <3>[ 2.653564] sr_dev_init: Unknown instance smartreflex0 <6>[ 2.659513] SmartReflex Class3 initialized <5>[ 2.667519] Loading compiled-in X.509 certificates <6>[ 2.767544] mmc1: new high speed MMC card at address 0001 <6>[ 2.778459] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 2.785200] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 2.793051] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 2.801400] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (248:0) <6>[ 2.819174] mmcblk1: p1 <6>[ 2.842577] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 2.849447] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 2.859510] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 2.867274] hctosys: unable to open rtc device (rtc0) <4>[ 2.872648] sr_init: No PMIC hook to init smartreflex <6>[ 2.896964] net eth0: initializing cpsw version 1.12 (0) <6>[ 3.006271] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 3.029591] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 6.116024] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 6.125329] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.154917] Sending DHCP requests ., OK <6>[ 6.199090] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.2 <6>[ 6.207243] IP-Config: Complete: <6>[ 6.210765] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.2, mask=255.255.255.0, gw=192.168.11.1 <6>[ 6.221316] host=192.168.11.2, domain=usen.ad.jp, nis-domain=(none) <6>[ 6.228413] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 6.228419] nameserver0=192.168.11.1 <6>[ 6.245416] Freeing unused kernel memory: 1024K <6>[ 6.255706] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.703647] udevd[85]: starting version 3.2.9 <5>[ 6.711668] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.720857] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.728158] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.748855] udevd[85]: specified user 'tss' unknown <27>[ 6.754463] udevd[85]: specified group 'tss' unknown <30>[ 6.771043] udevd[86]: starting eudev-3.2.9 <6>[ 7.483391] cpu cpu0: Linked as a consumer to regulator.3 <6>[ 7.535787] cpu cpu0: Dropping the link to regulator.3 <4>[ 7.583325] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <6>[ 7.616460] cpu cpu0: Linked as a consumer to regulator.3 <6>[ 7.736972] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 7.756744] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 7.777461] input: tps65217_pwrbutton as /devices/platform/ocp/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <6>[ 7.806082] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 7.855122] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <6>[ 8.203215] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 8.211403] random: crng init done <6>[ 8.223480] tda998x 0-0070: found TDA19988 <6>[ 8.271402] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_ops [tda998x]) <6>[ 8.279170] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 8.286197] [drm] No driver support for vblank timestamp query. <6>[ 8.410691] [drm] Cannot find any crtc or sizes <6>[ 8.462332] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <4>[ 8.635839] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator <6>[ 8.646447] am335x-phy-driver 47401300.usb-phy: Linked as a consumer to regulator.0 <6>[ 8.744264] usbcore: registered new interface driver usbfs <6>[ 8.751129] usbcore: registered new interface driver hub <6>[ 8.757179] usbcore: registered new device driver usb <4>[ 8.883583] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator <6>[ 8.894483] am335x-phy-driver 47401b00.usb-phy: Linked as a consumer to regulator.0 <3>[ 8.946699] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle <6>[ 8.968405] remoteproc remoteproc0: wkup_m3 is available <6>[ 8.980814] remoteproc remoteproc0: powering up wkup_m3 <4>[ 9.037120] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 9.047832] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 9.054078] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 9.111950] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.118943] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.216739] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 <6>[ 9.225802] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.233389] usb usb1: Product: MUSB HDRC host driver <6>[ 9.238727] usb usb1: Manufacturer: Linux 4.19.306-cip107 musb-hcd <6>[ 9.245261] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 9.418599] hub 1-0:1.0: USB hub found <6>[ 9.442852] hub 1-0:1.0: 1 port detected <6>[ 9.478127] [drm] Cannot find any crtc or sizes <3>[ 9.777960] pm33xx pm33xx: PM: Unable to allocate memory from ocmcram <4>[ 9.784995] pm33xx: probe of pm33xx failed with error -12 <6>[ 9.845199] asoc-simple-card sound: i2s-hifi <-> 48038000.mcasp mapping ok done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1095546/environment . /lava-1095546/environment / # /lava-1095546/bin/lava-test-runner /lava-1095546/0 /lava-1095546/bin/lava-test-runner /lava-1095546/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1095546/0/tests/0_dmesg + cat uuid + UUID=1095546_1.5.2.4.1 <8>[ 11.180664] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh kern :crit : timer_probe: no matching timers found <8>[ 11.297150] <8>[ 11.400835] <8>[ 11.503046] + set +x<8>[ 11.516072] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1095546/environment / # . /lava-1095546/environment/lava-1095546/bin/lava-test-runner /lava-1095546/1 / # /lava-1095546/bin/lava-test-runner /lava-1095546/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1095546/1/tests/1_bootrr + cat uuid + UUID=1095546_1.5.2.4.5 <8>[ 12.141678] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1095546/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-1095546/1/../bin/lava-test-case <8>[ 12.281957] /lava-1095546/1/../bin/lava-test-case <8>[ 12.381028] /lava-1095546/1/../bin/lava-test-case <8>[ 12.434477] /lava-1095546/1/../bin/lava-test-case <8>[ 12.546022] /lava-1095546/1/../bin/lava-test-case <8>[ 12.634596] /lava-1095546/1/../bin/lava-test-case <8>[ 12.704020] /lava-1095546/1/../bin/lava-test-case <8>[ 12.792862] /lava-1095546/1/../bin/lava-test-case <8>[ 12.880903] /lava-1095546/1/../bin/lava-test-case <8>[ 12.950384] /lava-1095546/1/../bin/lava-test-case <8>[ 13.038717] /lava-1095546/1/../bin/lava-test-case <8>[ 13.109028] /lava-1095546/1/../bin/lava-test-case <8>[ 13.229606] /lava-1095546/1/../bin/lava-test-case <8>[ 13.297959] /lava-1095546/1/../bin/lava-test-case <8>[ 13.351974] /lava-1095546/1/../bin/lava-test-case <8>[ 13.422978] /lava-1095546/1/../bin/lava-test-case <8>[ 13.511460] /lava-1095546/1/../bin/lava-test-case <8>[ 13.582709] /lava-1095546/1/../bin/lava-test-case <8>[ 14.712945] /lava-1095546/1/../bin/lava-test-case <8>[ 15.842691] /lava-1095546/1/../bin/lava-test-case <8>[ 15.912986] /lava-1095546/1/../bin/lava-test-case <8>[ 16.002187] /lava-1095546/1/../bin/lava-test-case <8>[ 16.090795] /lava-1095546/1/../bin/lava-test-case <8>[ 16.162616] /lava-1095546/1/../bin/lava-test-case <8>[ 16.252908] /lava-1095546/1/../bin/lava-test-case <8>[ 16.323827] /lava-1095546/1/../bin/lava-test-case <8>[ 16.412434] /lava-1095546/1/../bin/lava-test-case <8>[ 17.523060] /lava-1095546/1/../bin/lava-test-case <8>[ 18.641762] /lava-1095546/1/../bin/lava-test-case <8>[ 19.751185] /lava-1095546/1/../bin/lava-test-case <8>[ 20.859537] /lava-1095546/1/../bin/lava-test-case <8>[ 20.931033] /lava-1095546/1/../bin/lava-test-case <8>[ 21.019651] /lava-1095546/1/../bin/lava-test-case <8>[ 22.132387] /lava-1095546/1/../bin/lava-test-case <8>[ 23.242934] /lava-1095546/1/../bin/lava-test-case <8>[ 23.313670] /lava-1095546/1/../bin/lava-test-case <8>[ 23.403611] /lava-1095546/1/../bin/lava-test-case <8>[ 24.520409] /lava-1095546/1/../bin/lava-test-case <8>[ 25.633568] /lava-1095546/1/../bin/lava-test-case <8>[ 25.703820] /lava-1095546/1/../bin/lava-test-case <8>[ 25.793407] /lava-1095546/1/../bin/lava-test-case <8>[ 25.863491] /lava-1095546/1/../bin/lava-test-case <8>[ 25.954405] /lava-1095546/1/../bin/lava-test-case <8>[ 26.024183] /lava-1095546/1/../bin/lava-test-case <8>[ 26.113219] /lava-1095546/1/../bin/lava-test-case <8>[ 26.183926] /lava-1095546/1/../bin/lava-test-case <8>[ 26.272273] /lava-1095546/1/../bin/lava-test-case <8>[ 26.343342] /lava-1095546/1/../bin/lava-test-case <8>[ 26.432255] /lava-1095546/1/../bin/lava-test-case <8>[ 26.502534] /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: line 84: assert_device-present: not found /lava-1095546/1/../bin/lava-test-case <8>[ 26.575664] /lava-1095546/1/../bin/lava-test-case <8>[ 26.664129] /lava-1095546/1/../bin/lava-test-case <8>[ 26.747131] + set +x<8>[ 26.772599] / #