[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB OK In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (5 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 14214098/tftp-deploy-72pp85j7/kernel/zImage tftp 0x10000000 14214098/tftp-deploy-72pp85j7/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '14214098/tftp-deploy-72pp85j7/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 14.2 MiB/s done Bytes transferred = 10347008 (9de200 hex) => tftp 0x14000000 14214098/tftp-deploy-72pp85j7/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 14214098/tftp-deploy-72pp85j7/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '14214098/tftp-deploy-72pp85j7/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################ 14 MiB/s done Bytes transferred = 15490483 (ec5db3 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 14214098/tftp-deploy-72pp85j7/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 14214098/tftp-deploy-72pp85j7/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '14214098/tftp-deploy-72pp85j7/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 6.6 MiB/s done Bytes transferred = 41822 (a35e hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x9de200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15490419 Bytes = 14.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d35d Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.315-cip110 (KernelCI@build-j220663-arm-gcc-10-multi-v7-defconfig-kselftest-dqxz5) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Thu Jun 6 18:23:28 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s40168 r8192 d21272 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 925440K/1048576K available (14336K kernel code, 1760K rwdata, 6296K rodata, 2048K init, 7702K bss, 57600K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (15328 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1761 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7703 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 48567 entries in 190 pages <6>[ 0.000000] ftrace: allocated 190 pages with 6 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021900] Console: colour dummy device 80x30 <4>[ 0.023785] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.031811] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.036156] ... MAX_LOCK_DEPTH: 48 <4>[ 0.040563] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.045174] ... CLASSHASH_SIZE: 4096 <4>[ 0.049812] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.054483] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.059209] ... CHAINHASH_SIZE: 32768 <4>[ 0.063878] memory used by lock dependency info: 4655 kB <4>[ 0.069562] per task-struct memory footprint: 1536 bytes <6>[ 0.075237] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.085664] CPU: Testing write buffer coherency: ok <6>[ 0.090765] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.096103] pid_max: default: 32768 minimum: 301 <6>[ 0.101259] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.107873] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.117909] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.123243] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.130058] rcu: Hierarchical SRCU implementation. <6>[ 0.137173] EFI services will not be available. <6>[ 0.140062] smp: Bringing up secondary CPUs ... <6>[ 0.146325] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.146338] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.157925] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.157937] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.168828] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.168840] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.178058] smp: Brought up 1 node, 4 CPUs <6>[ 0.181937] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.188459] CPU: All CPU(s) started in SVC mode. <6>[ 0.196003] devtmpfs: initialized <6>[ 0.231528] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.239144] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.246864] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.257170] pinctrl core: initialized pinctrl subsystem <6>[ 0.264699] DMI not present or invalid. <6>[ 0.267929] NET: Registered protocol family 16 <6>[ 0.279031] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.289672] cpuidle: using governor menu <6>[ 0.291478] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.330712] vdd1p1: supplied by regulator-dummy <6>[ 0.334631] vdd3p0: supplied by regulator-dummy <6>[ 0.339254] vdd2p5: supplied by regulator-dummy <6>[ 0.344004] vddarm: supplied by regulator-dummy <6>[ 0.349479] vddpu: supplied by regulator-dummy <6>[ 0.353014] vddsoc: supplied by regulator-dummy <6>[ 0.404177] No ATAGs? <6>[ 0.404663] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.412723] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.429701] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.437706] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.461155] Serial: AMBA PL011 UART driver <6>[ 0.559820] mxs-dma 110000.dma-apbh: initialized <6>[ 0.585376] vgaarb: loaded <5>[ 0.588440] SCSI subsystem initialized <6>[ 0.590999] usbcore: registered new interface driver usbfs <6>[ 0.595548] usbcore: registered new interface driver hub <6>[ 0.601165] usbcore: registered new device driver usb <6>[ 0.610783] i2c i2c-0: IMX I2C adapter registered <6>[ 0.612938] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.620371] i2c i2c-1: IMX I2C adapter registered <6>[ 0.623461] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.630313] i2c i2c-2: IMX I2C adapter registered <6>[ 0.633987] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.643464] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.645901] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.655299] PTP clock support registered <6>[ 0.660257] EDAC MC: Ver: 3.0.0 <6>[ 0.673795] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.935709] NET: Registered protocol family 2 <6>[ 0.938151] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.946794] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 20480 bytes) <6>[ 0.952572] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.960040] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) <6>[ 0.967870] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.973809] UDP hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.979540] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.986649] NET: Registered protocol family 1 <6>[ 0.992451] RPC: Registered named UNIX socket transport module. <6>[ 0.996831] RPC: Registered udp transport module. <6>[ 1.001700] RPC: Registered tcp transport module. <6>[ 1.006715] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.015207] Trying to unpack rootfs image as initramfs... <6>[ 2.775117] Freeing initrd memory: 15128K <4>[ 2.777288] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 2.785085] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 2.799615] Initialise system trusted keyrings <6>[ 2.802267] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.836067] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.841926] NFS: Registering the id_resolver key type <5>[ 2.844816] Key type id_resolver registered <5>[ 2.849085] Key type id_legacy registered <6>[ 2.853511] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.865412] Key type asymmetric registered <5>[ 2.867005] Asymmetric key parser 'x509' registered <6>[ 2.872321] bounce: pool size: 64 pages <6>[ 2.876335] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 2.883909] io scheduler noop registered <6>[ 2.887993] io scheduler deadline registered <6>[ 2.892972] io scheduler cfq registered (default) <6>[ 2.897529] io scheduler mq-deadline registered <6>[ 2.902259] io scheduler kyber registered <4>[ 2.907134] test_firmware: interface ready <6>[ 2.984025] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.989040] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.996537] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.003253] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.054772] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 3.058433] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 3.066148] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 3.072502] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 3.080502] PU : no governor for states <6>[ 3.084134] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <4>[ 3.115250] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.122328] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.301239] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.317319] SuperH (H)SCI(F) driver initialized <6>[ 3.321412] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 3.330986] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 3.340093] console [ttymxc1] enabled <6>[ 3.340093] console [ttymxc1] enabled <6>[ 3.345188] bootconsole [ec_imx21] disabled <6>[ 3.345188] bootconsole [ec_imx21] disabled <6>[ 3.358112] msm_serial: driver initialized <6>[ 3.363325] STMicroelectronics ASC driver initialized <6>[ 3.373818] STM32 USART driver initialized <6>[ 3.393126] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 3.417326] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.426288] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.433543] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.440603] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.449942] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.457512] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.493833] brd: module loaded <6>[ 3.525406] loop: module loaded <6>[ 3.538441] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.546706] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.555056] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.563523] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 3.574950] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.582225] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.591377] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.604534] scsi host0: ahci-imx <6>[ 3.609856] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 3.653577] CAN device driver interface <6>[ 3.661110] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 3.670053] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 3.679333] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 3.689515] pps pps0: new PPS source ptp0 <6>[ 3.737536] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.746816] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 3.752935] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.759380] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 3.766674] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.789068] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.796914] usbcore: registered new interface driver pegasus <6>[ 3.803005] usbcore: registered new interface driver asix <6>[ 3.808846] usbcore: registered new interface driver ax88179_178a <6>[ 3.815373] usbcore: registered new interface driver cdc_ether <6>[ 3.821655] usbcore: registered new interface driver smsc75xx <6>[ 3.827878] usbcore: registered new interface driver smsc95xx <6>[ 3.834062] usbcore: registered new interface driver net1080 <6>[ 3.840104] usbcore: registered new interface driver cdc_subset <6>[ 3.846455] usbcore: registered new interface driver zaurus <6>[ 3.852505] usbcore: registered new interface driver cdc_ncm <6>[ 3.867102] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.873974] ehci-pci: EHCI PCI platform driver <6>[ 3.878841] ehci-platform: EHCI generic platform driver <6>[ 3.885189] ehci-orion: EHCI orion driver <6>[ 3.890171] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.895178] ehci-st: EHCI STMicroelectronics driver <6>[ 3.900980] ehci-exynos: EHCI EXYNOS driver <6>[ 3.906136] ehci-atmel: EHCI Atmel driver <6>[ 3.911068] tegra-ehci: Tegra EHCI driver <6>[ 3.916093] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.922610] ohci-pci: OHCI PCI platform driver <6>[ 3.927519] ohci-platform: OHCI generic platform driver <6>[ 3.933830] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.938777] ohci-st: OHCI STMicroelectronics driver <6>[ 3.944636] ohci-atmel: OHCI Atmel driver <6>[ 3.946162] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.951574] usbcore: registered new interface driver usb-storage <6>[ 3.954774] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.967184] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 3.967546] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.984256] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 3.996026] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.001404] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.033801] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.043329] hub 1-0:1.0: USB hub found <6>[ 4.047763] hub 1-0:1.0: 1 port detected <6>[ 4.073944] i2c /dev entries driver <6>[ 4.124688] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 4.145928] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.152393] sdhci: Copyright(c) Pierre Ossman <6>[ 4.163196] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.175452] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.183233] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 4.189026] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 4.194892] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 4.238772] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 4.247542] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 4.253403] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 4.294429] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 4.313550] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.323057] usbcore: registered new interface driver usbhid <6>[ 4.329016] usbhid: USB HID core driver <6>[ 4.337645] mmc0: new high speed SDHC card at address 0001 <6>[ 4.343829] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.348005] mmcblk0: mmc0:0001 SD 14.8 GiB <6>[ 4.350588] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.352231] IPv4 over IPsec tunneling driver <6>[ 4.369339] NET: Registered protocol family 10 <6>[ 4.378106] Segment Routing with IPv6 <6>[ 4.384497] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.394630] NET: Registered protocol family 17 <6>[ 4.399400] can: controller area network core (rev 20170425 abi 9) <6>[ 4.406127] NET: Registered protocol family 29 <6>[ 4.410923] can: raw protocol (rev 20170425) <6>[ 4.415628] can: broadcast manager protocol (rev 20170425 t) <6>[ 4.421607] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 4.428731] Key type dns_resolver registered <6>[ 4.442954] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 4.448985] cpu cpu0: Linked as a consumer to regulator.5 <4>[ 4.454836] ------------[ cut here ]------------ <6>[ 4.455003] cpu cpu0: Linked as a consumer to regulator.6 <4>[ 4.459738] WARNING: CPU: 1 PID: 0 at include/trace/events/lock.h:13 lock_acquire+0x138/0x1f0 <4>[ 4.459745] Modules linked in: <6>[ 4.469901] ThumbEE CPU extension supported. <4>[ 4.474196] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.19.315-cip110 #1 <4>[ 4.474202] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 4.474207] Backtrace: <4>[ 4.474229] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 4.474240] r7:ffffffff r6:00000000 r5:60000093 r4:c1b9d048 <4>[ 4.474253] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 4.474264] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <4>[ 4.474278] r9:60000093 r8:c1a084bc r7:00000000 r6:00000009 r5:00000000 r4:00000000 <5>[ 4.477624] Registering SWP/SWPB emulation handler <4>[ 4.482134] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 4.482142] r6:c03b8e24 r5:0000000d r4:c157e7e0 <4>[ 4.490489] ------------[ cut here ]------------ <5>[ 4.493368] Loading compiled-in X.509 certificates <4>[ 4.495914] [] (warn_slowpath_null) from [] (lock_acquire+0x138/0x1f0) <4>[ 4.495932] r6:00000000 r5:00000000 r4:c1a11090 <4>[ 4.498675] WARNING: CPU: 3 PID: 0 at include/trace/events/lock.h:58 lock_release+0x364/0x370 <4>[ 4.506515] [] (lock_acquire) from [] (_raw_spin_lock+0x58/0x68) <4>[ 4.512413] Modules linked in: <4>[ 4.519996] r10:c1a084bc r9:00000001 r8:c1ba5310 r7:00000001 r6:c1a10da4 r5:c1a084bc <4>[ 4.605674] r4:c1a11080 <4>[ 4.608522] [] (_raw_spin_lock) from [] (imx6q_enter_wait+0x30/0xb4) <4>[ 4.616895] r4:c1bba4b8 <4>[ 4.619729] [] (imx6q_enter_wait) from [] (cpuidle_enter_state+0x188/0x518) <4>[ 4.628714] r7:ef7ab338 r6:c1a10da4 r5:c1a10d44 r4:00000001 <4>[ 4.634664] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 4.643220] r10:c1a10d44 r9:ef7ab338 r8:c19a1330 r7:c1a08500 r6:c1a10d44 r5:ef7ab338 <4>[ 4.651327] r4:00000001 <4>[ 4.654167] [] (cpuidle_enter) from [] (do_idle+0x220/0x2e0) <4>[ 4.661848] r7:c1a08500 r6:c1a084bc r5:00000001 r4:ee9d4000 <4>[ 4.667804] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 4.675665] r10:00000000 r9:412fc09a r8:1020406a r7:c1bb9650 r6:00000001 r5:ee9d4000 <6>[ 4.677646] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <4>[ 4.683768] r4:0000008a <4>[ 4.683802] [] (cpu_startup_entry) from [] (secondary_start_kernel+0x170/0x17c) <4>[ 4.683827] [] (secondary_start_kernel) from [<1030312c>] (0x1030312c) <4>[ 4.683846] r7:c1bb9650 r6:10c0387d r5:00000051 r4:3e9c006a <4>[ 4.683858] irq event stamp: 8380 <4>[ 4.683871] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.19.315-cip110 #1 <4>[ 4.683898] hardirqs last enabled at (8379): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 4.683904] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 4.683923] hardirqs last disabled at (8380): [] do_idle+0xb0/0x2e0 <4>[ 4.683925] Backtrace: <4>[ 4.683959] softirqs last enabled at (8374): [] __do_softirq+0x344/0x520 <4>[ 4.683987] [] (dump_backtrace) from [] (show_stack+0x20/0x24) <4>[ 4.684013] softirqs last disabled at (8351): [] irq_exit+0x170/0x1c8 <4>[ 4.684023] ---[ end trace 520a7748d79a6882 ]--- <6>[ 4.692449] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <4>[ 4.694228] r7:ffffffff r6:00000000 r5:60000093 r4:c1b9d048 <4>[ 4.694251] [] (show_stack) from [] (dump_stack+0xe0/0x10c) <4>[ 4.694273] [] (dump_stack) from [] (__warn.part.0+0xa8/0xd8) <4>[ 4.694294] r9:c032d5c4 r8:c1ba5310 r7:60000093 r6:00000009 r5:00000000 r4:00000000 <4>[ 4.694317] [] (__warn.part.0) from [] (warn_slowpath_null+0x54/0x5c) <4>[ 4.694333] r6:c03b8ce0 r5:0000003a r4:c157e7e0 <4>[ 4.694359] [] (warn_slowpath_null) from [] (lock_release+0x364/0x370) <4>[ 4.694385] r6:00000001 r5:c1a11090 r4:c1a084bc <4>[ 4.694413] [] (lock_release) from [] (_raw_spin_unlock+0x28/0x4c) <4>[ 4.694433] r10:c1a084bc r9:00000001 r8:c1ba5310 r7:00000001 r6:00000001 r5:c1a084bc <6>[ 4.715630] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <4>[ 4.717437] r4:c1a11080 <4>[ 4.717482] [] (_raw_spin_unlock) from [] (imx6q_enter_wait+0x54/0xb4) <6>[ 4.721600] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 4.728012] r5:c1a084bc r4:c1bba4b8 <4>[ 4.728039] [] (imx6q_enter_wait) from [] (cpuidle_enter_state+0x188/0x518) <4>[ 4.728055] r7:ef7cd338 r6:c1a10da4 r5:c1a10d44 r4:00000001 <4>[ 4.728073] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x40/0x4c) <4>[ 4.728095] r10:c1a10d44 r9:ef7cd338 r8:c19a1330 r7:c1a08500 r6:c1a10d44 r5:ef7cd338 <4>[ 4.728103] r4:00000001 <4>[ 4.728130] [] (cpuidle_enter) from [] (do_idle+0x220/0x2e0) <4>[ 4.728146] r7:c1a08500 r6:c1a084bc r5:00000003 r4:ee9d8000 <4>[ 4.728180] [] (do_idle) from [] (cpu_startup_entry+0x28/0x2c) <4>[ 4.749270] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <4>[ 4.751423] r10:00000000 r9:412fc09a r8:1020406a r7:c1bb9650 r6:00000003 r5:ee9d8000 <4>[ 4.751440] r4:0000008a <4>[ 4.751471] [] (cpu_startup_entry) from [] (secondary_start_kernel+0x170/0x17c) <6>[ 4.755052] panel-simple panel-lcd: Linked as a consumer to regulator.0 <4>[ 4.762215] [] (secondary_start_kernel) from [<1030312c>] (0x1030312c) <4>[ 4.762233] r7:c1bb9650 r6:10c0387d r5:00000051 r4:3e9c006a <6>[ 4.770866] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 4.777646] irq event stamp: 3028 <4>[ 4.777671] hardirqs last enabled at (3027): [] _raw_read_unlock_irqrestore+0x64/0x6c <4>[ 4.777692] hardirqs last disabled at (3028): [] do_idle+0xb0/0x2e0 <4>[ 4.777718] softirqs last enabled at (3012): [] _local_bh_enable+0x34/0x68 <4>[ 4.777737] softirqs last disabled at (3011): [] irq_enter+0x6c/0x94 <4>[ 4.777748] ---[ end trace 520a7748d79a6883 ]--- <4>[ 5.048879] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.058114] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.066293] hub 1-1:1.0: USB hub found <6>[ 5.066950] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.070661] hub 1-1:1.0: 3 ports detected <6>[ 5.086369] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 5.099492] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.107591] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.118922] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.126980] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.138920] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.147828] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.155291] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.166002] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.175229] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.182809] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.193843] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.201659] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.212909] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <4>[ 5.220666] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 5.228489] GPT:7812499 != 30965759 <4>[ 5.232254] GPT:Alternate GPT header not at the end of the disk. <4>[ 5.238620] GPT:7812499 != 30965759 <4>[ 5.242386] GPT: Use GNU Parted to correct GPT errors. <6>[ 5.247890] mmcblk0: p1 p2 p3 <6>[ 5.251899] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.263984] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.272818] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.280787] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.291490] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.300720] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.312634] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.322967] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.332729] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.344077] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.351720] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.363789] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.372622] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.379836] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.390471] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.399710] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.407086] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.419726] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 5.427650] hctosys: unable to open rtc device (rtc0) <6>[ 5.437521] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 5.445233] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 5.456822] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 5.464545] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 5.476491] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 5.485532] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 5.492701] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 5.503344] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 5.512574] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 5.519953] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.577292] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 5.593945] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 8.735941] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 8.745087] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.773803] Sending DHCP requests ., OK <6>[ 8.818406] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 <6>[ 8.826901] IP-Config: Complete: <6>[ 8.830451] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 <6>[ 8.841344] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) <6>[ 8.849585] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 8.849600] nameserver0=192.168.201.1 <6>[ 8.905091] Freeing unused kernel memory: 2048K <6>[ 8.924348] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 9.272064] udevd[108]: starting version 3.2.9 <5>[ 9.279371] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 9.287013] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 9.293951] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 9.312266] udevd[108]: specified user 'tss' unknown <27>[ 9.317850] udevd[108]: specified group 'tss' unknown <30>[ 9.329269] udevd[109]: starting eudev-3.2.9 <6>[ 10.288792] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 10.297630] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 10.298955] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 10.329476] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 10.341922] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 10.360287] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 10.363115] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <4>[ 10.372799] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 10.383875] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 10.384645] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 10.398117] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 10.402284] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <4>[ 10.409015] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 10.411710] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 10.420949] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 10.439715] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 10.450280] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 10.459138] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 10.505613] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 10.536421] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 10.542876] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 10.558936] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 10.568768] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 10.576651] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 1 <6>[ 10.577975] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 10.590751] sgtl5000 0-000a: Linked as a consumer to regulator.8 <4>[ 10.597396] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 10.606575] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 10.614140] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 10.625737] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 10.625932] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 10.640209] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 10.647960] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 10.658701] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 10.666573] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 10.678854] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 10.686765] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 10.688944] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 10.804046] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 10.812912] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 10.821432] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 10.832475] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 10.841886] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 10.850496] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 10.861454] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 10.869373] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 10.882173] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 10.890188] pwm-backlight backlight-lvds: Dropping the link to regulator.8 done Saving random seed: <5>[ 11.316917] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 11.564590] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-14214098/environment . /lava-14214098/environment / # /lava-14214098/bin/lava-test-runner /lava-14214098/0 /lava-14214098/bin/lava-test-runner /lava-14214098/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-14214098/0/tests/0_dmesg + cat uuid + UUID=14214098_1.5.2.4.1 <8>[ 12.300407] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 12.412062] <8>[ 12.506050] <8>[ 12.600040] + set +x <8>[ 12.611399] / #