connecting to NetworkSerialPort(target=Target(name='dove-cubox-0', env=None), name='NetworkSerialPort', state=, avail=True, host='moxa.cuskci.stw.pengutronix.de', port=4015, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t moxa.cuskci.stw.pengutronix.de:4015 connected to 10.8.254.5 (port 4015) Escape character: Ctrl-\ Type the escape character to get to the prompt. barebox 2020.06.0-00092-gc130f9ac29 #2 Fri Jul 3 17:13:59 CEST 2020 Board: Marvell Dove SoC: Marvell 0510 rev 7 mdio_bus: miibus0: probed [33mWARNING:[0m m25p80 spi-flash@00: found n25q032, expected w25q32 m25p80 spi-flash@00: n25q032 (4096 Kbytes) dove-sdhci f1092000.sdio-host@92000.of: registered as mci0 mci0: detected SD card version 2.0 mci0: registered disk0 malloc space: 0x1fefe1a0 -> 0x3fdfc33f (size 511 MiB) envfs: no envfs (magic mismatch) - envfs never written? [?25h Hit m for menu or any to stop autoboot: 3 [1;32mbarebox@[1;36mMarvell Dove:/[0m bootm -v -r /mnt/tftp/1005590/tftp-deploy-v_hel79s/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/1005590/tftp-deploy-v_hel79s/dtb/dove-cubox.dtb /mnt/tftp/1005590/tftp-deploy-v_hel79s/kernel/zImage -a 0x05000000 -L 0x04000000 [1;32mbarebox@[1;36mMarvell Dove:/[0m bootm -v -r /mnt/tftp/1005590/tftp-deploy-v_hel79s/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/1005590/tftp-deploy-v_hel79s/dtb/dove-cubox.dtb /mnt/tftp/1005590/tftp-deploy-v_hel79s/kernel/zImage -a 0x05000000 -L 0x04000000 eth0: 1000Mbps full duplex link detected [33mWARNING:[0m eth0: No MAC address set. Using random address 16:ae:f4:c1:ff:49 T eth0: DHCP client bound to address 10.8.254.168 Loading ARM Linux zImage '/mnt/tftp/1005590/tftp-deploy-v_hel79s/kernel/zImage' OS image not yet relocated Passing control to ARM zImage handler Loaded initrd GZIP compressed '/mnt/tftp/1005590/tftp-deploy-v_hel79s/ramdisk/ramdisk.cpio.gz' initrd is at 0x04000000-0x04a8823a Loading devicetree from '/mnt/tftp/1005590/tftp-deploy-v_hel79s/dtb/dove-cubox.dtb' commandline: console=ttyS0,115200n8 earlyprintk Starting kernel at 0x05000000, initrd at 0x04000000, oftree at 0x04a89000... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.302-cip80-rt46 (KernelCI@build-j83949-arm-gcc-10-multi-v7-defconfig-preempt-rt-snpzm) (gcc version 10.2.1 20210110 (Debian 10.2.1-6) ) #1 SMP PREEMPT RT Sat Oct 28 18:54:45 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [560f5815] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: SolidRun CuBox [ 0.000000] cma: Reserved 64 MiB at 0x3c000000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] PERCPU: Embedded 12 pages/cpu @ef7d4000 s16672 r8192 d24288 u49152 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 947516K/1048576K available (8718K kernel code, 1024K rwdata, 3900K rodata, 1032K init, 325K bss, 35524K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0e5b9bc (12623 kB) [ 0.000000] .init : 0xc0e5c000 - 0xc0f5e000 (1032 kB) [ 0.000000] .data : 0xc0f5e000 - 0xc105e160 (1025 kB) [ 0.000000] .bss : 0xc1061000 - 0xc10b2474 ( 326 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000009] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.001226] Console: colour dummy device 80x30 [ 0.030021] Calibrating delay loop... 791.34 BogoMIPS (lpj=1978368) [ 0.030027] pid_max: default: 32768 minimum: 301 [ 0.030181] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.030192] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.031025] CPU: Testing write buffer coherency: ok [ 0.031302] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.031424] Setting up static identity map for 0x209000 - 0x209098 [ 0.075132] Brought up 1 CPUs [ 0.075154] SMP: Total of 1 processors activated (791.34 BogoMIPS). [ 0.075166] CPU: All CPU(s) started in SVC mode. [ 0.075965] devtmpfs: initialized [ 0.083551] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 5 [ 0.084233] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns [ 0.084278] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.090288] pinctrl core: initialized pinctrl subsystem [ 0.092775] NET: Registered protocol family 16 [ 0.097985] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.115134] cpuidle: using governor ladder [ 0.130131] cpuidle: using governor menu [ 0.130520] Dove 88AP510 SoC [ 0.130546] Tauros2: Disabling L2 prefetch. [ 0.130557] Tauros2: Disabling line fill burt8. [ 0.130567] Tauros2: Enabling L2 cache. [ 0.130576] Tauros2: L2 cache support initialised in ARMv7 mode. [ 0.142467] No ATAGs? [ 0.142492] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.146725] Serial: AMBA PL011 UART driver [ 0.198571] reg-fixed-voltage regulators:regulator@1: could not find pctldev for node /mbus/internal-regs/power-management@d0000/pin-ctrl@0200/pmx-gpio-1, deferring probe [ 0.201541] vgaarb: loaded [ 0.202824] SCSI subsystem initialized [ 0.205612] usbcore: registered new interface driver usbfs [ 0.205709] usbcore: registered new interface driver hub [ 0.205775] usbcore: registered new device driver usb [ 0.207332] pps_core: LinuxPPS API ver. 1 registered [ 0.207345] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.207390] PTP clock support registered [ 0.207615] EDAC MC: Ver: 3.0.0 [ 0.215259] clocksource: Switched to clocksource orion_clocksource [ 0.230102] NET: Registered protocol family 2 [ 0.230351] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.231516] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.231623] TCP bind hash table entries: 8192 (order: 5, 229376 bytes) [ 0.231972] TCP: Hash tables configured (established 8192 bind 8192) [ 0.232080] UDP hash table entries: 512 (order: 3, 32768 bytes) [ 0.232150] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes) [ 0.232384] NET: Registered protocol family 1 [ 0.237825] RPC: Registered named UNIX socket transport module. [ 0.237839] RPC: Registered udp transport module. [ 0.237849] RPC: Registered tcp transport module. [ 0.237858] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.238390] Unpacking initramfs... [ 1.137559] Freeing initrd memory: 10788K [ 1.163277] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.164846] NFS: Registering the id_resolver key type [ 1.164909] Key type id_resolver registered [ 1.164920] Key type id_legacy registered [ 1.165015] ntfs: driver 2.1.32 [Flags: R/O]. [ 1.167337] bounce: pool size: 64 pages [ 1.167655] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.167676] io scheduler noop registered [ 1.167692] io scheduler deadline registered [ 1.168230] io scheduler cfq registered (default) [ 1.174520] dove-pinctrl f10d0200.pin-ctrl: falling back to hardcoded PMU resource [ 1.174679] dove-pinctrl f10d0200.pin-ctrl: [Firmware Bug]: Missing pinctrl regs in DTB. Please update your firmware. [ 1.175596] dove-pinctrl f10d0200.pin-ctrl: registered pinctrl driver [ 1.179602] irq: Cannot allocate irq_descs @ IRQ39, assuming pre-allocated [ 1.180129] irq: Cannot allocate irq_descs @ IRQ71, assuming pre-allocated [ 1.184803] mv_xor f1060800.dma-engine: Marvell shared XOR driver [ 1.222427] mv_xor f1060800.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.222708] mv_xor f1060900.dma-engine: Marvell shared XOR driver [ 1.257384] mv_xor f1060900.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.346096] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.349188] SuperH (H)SCI(F) driver initialized [ 1.350104] msm_serial: driver initialized [ 1.351300] console [ttyS0] disabled [ 1.351386] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 21, base_baud = 10416666) is a 16550A [ 1.999298] console [ttyS0] enabled [ 2.003603] STMicroelectronics ASC driver initialized [ 2.010397] [drm] Initialized drm 1.1.0 20060810 [ 2.066437] loop: module loaded [ 2.072433] sata_mv f10a0000.sata-host: slots 32 ports 1 [ 2.085379] scsi host0: sata_mv [ 2.088907] ata1: SATA max UDMA/133 irq 30 [ 2.096408] m25p80 spi0.0: found n25q032, expected w25q32 [ 2.101913] m25p80 spi0.0: n25q032 (4096 Kbytes) [ 2.106534] 2 ofpart partitions found on MTD device spi0.0 [ 2.111997] Creating 2 MTD partitions on \"spi0.0\": [ 2.116782] 0x000000000000-0x000000200000 : \"barebox\" [ 2.128384] 0x000000200000-0x000000220000 : \"env\" [ 2.144332] CAN device driver interface [ 2.149441] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 2.156372] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.188918] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.198324] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 16:ae:f4:c1:ff:49 [ 2.209723] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.217181] usbcore: registered new interface driver pegasus [ 2.222926] usbcore: registered new interface driver asix [ 2.228375] usbcore: registered new interface driver ax88179_178a [ 2.234516] usbcore: registered new interface driver cdc_ether [ 2.240430] usbcore: registered new interface driver smsc75xx [ 2.246251] usbcore: registered new interface driver smsc95xx [ 2.252047] usbcore: registered new interface driver net1080 [ 2.257768] usbcore: registered new interface driver cdc_subset [ 2.263737] usbcore: registered new interface driver zaurus [ 2.269417] usbcore: registered new interface driver cdc_ncm [ 2.276922] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.283431] ehci-pci: EHCI PCI platform driver [ 2.287942] ehci-platform: EHCI generic platform driver [ 2.293337] ehci-omap: OMAP-EHCI Host Controller driver [ 2.298697] ehci-orion: EHCI orion driver [ 2.302893] orion-ehci f1050000.usb-host: EHCI Host Controller [ 2.308731] orion-ehci f1050000.usb-host: new USB bus registered, assigned bus number 1 [ 2.317125] orion-ehci f1050000.usb-host: irq 25, io mem 0xf1050000 [ 2.330282] orion-ehci f1050000.usb-host: USB 2.0 started, EHCI 1.00 [ 2.337783] hub 1-0:1.0: USB hub found [ 2.341557] hub 1-0:1.0: 1 port detected [ 2.346137] orion-ehci f1051000.usb-host: EHCI Host Controller [ 2.351973] orion-ehci f1051000.usb-host: new USB bus registered, assigned bus number 2 [ 2.360344] orion-ehci f1051000.usb-host: irq 26, io mem 0xf1051000 [ 2.375293] orion-ehci f1051000.usb-host: USB 2.0 started, EHCI 1.00 [ 2.382704] hub 2-0:1.0: USB hub found [ 2.386475] hub 2-0:1.0: 1 port detected [ 2.391037] SPEAr-ehci: EHCI SPEAr driver [ 2.395227] ehci-st: EHCI STMicroelectronics driver [ 2.400384] ehci-exynos: EHCI EXYNOS driver [ 2.404723] ehci-atmel: EHCI Atmel driver [ 2.408878] tegra-ehci: Tegra EHCI driver [ 2.413736] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.419918] ohci-pci: OHCI PCI platform driver [ 2.424434] ohci-platform: OHCI generic platform driver [ 2.425301] ata1: SATA link down (SStatus 0 SControl F300) [ 2.435313] ohci-omap3: OHCI OMAP3 driver [ 2.439461] SPEAr-ohci: OHCI SPEAr driver [ 2.443611] ohci-st: OHCI STMicroelectronics driver [ 2.448631] ohci-atmel: OHCI Atmel driver [ 2.453278] usbcore: registered new interface driver usb-storage [ 2.461040] mousedev: PS/2 mouse device common for all mice [ 2.474791] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time- as rtc0 [ 2.485096] i2c /dev entries driver [ 2.493176] i2c i2c-0: Added multiplexed i2c bus 1 [ 2.498440] i2c i2c-0: Added multiplexed i2c bus 2 [ 2.503699] i2c i2c-0: Added multiplexed i2c bus 3 [ 2.512781] orion_wdt: Initial timeout 25 sec [ 2.519835] sdhci: Secure Digital Host Controller Interface driver [ 2.525989] sdhci: Copyright(c) Pierre Ossman [ 2.531994] Synopsys Designware Multimedia Card Interface Driver [ 2.539016] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.545201] sdhci-dove f1092000.sdio-host: No vmmc regulator found [ 2.551362] sdhci-dove f1092000.sdio-host: No vqmmc regulator found [ 2.585286] mmc0: SDHCI controller on f1092000.sdio-host [f1092000.sdio-host] using DMA [ 2.601590] usbcore: registered new interface driver usbhid [ 2.607137] usbhid: USB HID core driver [ 2.616344] NET: Registered protocol family 10 [ 2.627081] sit: IPv6 over IPv4 tunneling driver [ 2.630065] mmc0: new high speed SD card at address 59b4 [ 2.637826] mmcblk0: mmc0:59b4 USD 1.87 GiB [ 2.643624] mmcblk0: p1 [ 2.645795] NET: Registered protocol family 17 [ 2.645819] can: controller area network core (rev 20120528 abi 9) [ 2.645933] NET: Registered protocol family 29 [ 2.645948] can: raw protocol (rev 20120528) [ 2.645961] can: broadcast manager protocol (rev 20120528 t) [ 2.645981] can: netlink gateway (rev 20130117) max_hops=1 [ 2.646560] Key type dns_resolver registered [ 2.646657] ThumbEE CPU extension supported. [ 2.646680] Registering SWP/SWPB emulation handler [ 2.646692] PJ4 iWMMXt v2 coprocessor enabled. [ 2.661724] rtc-mv f10d8500.real-time-clock: setting system clock to 2023-01-20 07:22:16 UTC (1674199336) [ 2.714788] Freeing unused kernel memory: 1032K [ 2.751735] devpts: called with bogus options Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 2.895556] udevd[104]: starting version 3.2.9 [ 2.901546] random: udevd: uninitialized urandom read (16 bytes read, 0 bits of entropy available) [ 2.910812] random: udevd: uninitialized urandom read (16 bytes read, 0 bits of entropy available) [ 2.920024] random: udevd: uninitialized urandom read (16 bytes read, 0 bits of entropy available) [ 2.939411] udevd[104]: specified user 'tss' unknown [ 2.944527] udevd[104]: specified group 'tss' unknown [ 2.954222] udevd[105]: starting eudev-3.2.9 done Saving random seed: [ 4.807199] random: dd: uninitialized urandom read (512 bytes read, 4 bits of entropy available) OK Starting network: OK Starting dropbear sshd: [ 4.915443] random: dropbear: uninitialized urandom read (32 bytes read, 4 bits of entropy available) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1005590/environment . /lava-1005590/environment / # /lava-1005590/bin/lava-test-runner /lava-1005590/0 /lava-1005590/bin/lava-test-runner /lava-1005590/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1005590/0/tests/0_dmesg + cat uuid + UUID=1005590_1[ 5.501252] .5.2.3.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 5.552719] [ 5.598981] [ 5.646242] + set[ 5.656642] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1005590/environment / # . /lava-1005590/environment/lava-1005590/bin/lava-test-runner /lava-1005590/1 / # /lava-1005590/bin/lava-test-runner /lava-1005590/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1005590/1/tests/1_bootrr + cat uuid + [ 6.143456] UUID=1005590_1.5.2.3.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1005590/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-1005590/1/../bin/lava-test-case [ 6.181540] /lava-1005590/1/../bin/lava-test-case [ 6.225928] /lava-1005590/1/../bin/lava-test-case [ 6.253144] + set +x[ 6.273417] / #