[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.33 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 13757634/tftp-deploy-naqa_sb5/kernel/zImage tftp 0x10000000 13757634/tftp-deploy-naqa_sb5/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '13757634/tftp-deploy-naqa_sb5/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# 7.7 MiB/s done Bytes transferred = 6666568 (65b948 hex) => tftp 0x14000000 13757634/tftp-deploy-naqa_sb5/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 13757634/tftp-deploy-naqa_sb5/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '13757634/tftp-deploy-naqa_sb5/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################# 13.9 MiB/s done Bytes transferred = 7874388 (782754 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 13757634/tftp-deploy-naqa_sb5/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 13757634/tftp-deploy-naqa_sb5/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '13757634/tftp-deploy-naqa_sb5/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 8.7 MiB/s done Bytes transferred = 36559 (8ecf hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/13757634/extract-nfsrootfs-y3880nco,tcp,hard,v3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/13757634/extract-nfsrootfs-y3880nco,tcp,hard,v3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x65b948 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 7874324 Bytes = 7.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0bece Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.302-cip87-rt49 (KernelCI@build-j195222-arm-gcc-10-multi-v7-defconfig-preempt-rt-5g8gj) (gcc version 10.2.1 20210110 (Debian 10.2.1-6) ) #1 SMP PREEMPT RT Mon May 13 09:08:07 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] bootconsole [uart0] enabled [ 0.000000] Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] PERCPU: Embedded 12 pages/cpu @ef7a2000 s16672 r8192 d24288 u49152 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/13757634/extract-nfsrootfs-y3880nco,tcp,hard,v3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 950416K/1048576K available (8718K kernel code, 1025K rwdata, 3904K rodata, 1028K init, 325K bss, 32624K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0e5c9f0 (12627 kB) [ 0.000000] .init : 0xc0e5d000 - 0xc0f5e000 (1028 kB) [ 0.000000] .data : 0xc0f5e000 - 0xc105e460 (1026 kB) [ 0.000000] .bss : 0xc1061000 - 0xc10b246c ( 326 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=4 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C-310 erratum 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000019] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.002323] Console: colour dummy device 80x30 [ 0.251972] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=15000) [ 0.251977] pid_max: default: 32768 minimum: 301 [ 0.252091] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.252099] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.252779] CPU: Testing write buffer coherency: ok [ 0.252785] CPU0: Spectre v2: using BPIALL workaround [ 0.253098] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.296056] Setting up static identity map for 0x10209000 - 0x10209098 [ 0.364603] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.364609] CPU1: Spectre v2: using BPIALL workaround [ 0.384592] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.384598] CPU2: Spectre v2: using BPIALL workaround [ 0.404592] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.404597] CPU3: Spectre v2: using BPIALL workaround [ 0.404691] Brought up 4 CPUs [ 0.436912] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.443084] CPU: All CPU(s) started in SVC mode. [ 0.448761] devtmpfs: initialized [ 0.462241] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.467793] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns [ 0.476815] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.486485] pinctrl core: initialized pinctrl subsystem [ 0.491103] NET: Registered protocol family 16 [ 0.498123] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.514383] cpuidle: using governor ladder [ 0.529365] cpuidle: using governor menu [ 0.530741] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.561615] No ATAGs? [ 0.561677] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.569035] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.578513] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.585797] Serial: AMBA PL011 UART driver [ 0.589725] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 0.620953] mxs-dma 110000.dma-apbh: initialized [ 0.629528] vgaarb: loaded [ 0.630681] SCSI subsystem initialized [ 0.633668] usbcore: registered new interface driver usbfs [ 0.638672] usbcore: registered new interface driver hub [ 0.643963] usbcore: registered new device driver usb [ 0.651256] pps_core: LinuxPPS API ver. 1 registered [ 0.653912] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.663073] PTP clock support registered [ 0.667253] EDAC MC: Ver: 3.0.0 [ 0.673276] clocksource: Switched to clocksource mxc_timer1 [ 0.688709] NET: Registered protocol family 2 [ 0.690357] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.698191] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.704055] TCP bind hash table entries: 8192 (order: 5, 229376 bytes) [ 0.710875] TCP: Hash tables configured (established 8192 bind 8192) [ 0.717020] UDP hash table entries: 512 (order: 3, 32768 bytes) [ 0.722823] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes) [ 0.729384] NET: Registered protocol family 1 [ 0.733814] RPC: Registered named UNIX socket transport module. [ 0.739369] RPC: Registered udp transport module. [ 0.744065] RPC: Registered tcp transport module. [ 0.748766] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.755797] Unpacking initramfs... [ 1.354206] Freeing initrd memory: 7692K [ 1.355766] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 1.379023] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.383177] NFS: Registering the id_resolver key type [ 1.387086] Key type id_resolver registered [ 1.391230] Key type id_legacy registered [ 1.395319] ntfs: driver 2.1.32 [Flags: R/O]. [ 1.401404] bounce: pool size: 64 pages [ 1.403666] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.410814] io scheduler noop registered [ 1.414727] io scheduler deadline registered [ 1.419372] io scheduler cfq registered (default) [ 1.447062] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 1.453713] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 1.524034] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.530719] SuperH (H)SCI(F) driver initialized [ 1.533403] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 24, base_baud = 5000000) is a IMX [ 1.541900] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 295, base_baud = 5000000) is a IMX [ 1.552624] console [ttymxc1] enabled [ 1.552624] console [ttymxc1] enabled [ 1.557086] bootconsole [uart0] disabled [ 1.557086] bootconsole [uart0] disabled [ 1.566085] msm_serial: driver initialized [ 1.572664] STMicroelectronics ASC driver initialized [ 1.580236] [drm] Initialized drm 1.1.0 20060810 [ 1.589045] lcd_panel supply power not found, using dummy regulator [ 1.595589] panel supply power not found, using dummy regulator [ 1.615291] loop: module loaded [ 1.629258] CAN device driver interface [ 1.635317] 2188000.ethernet supply phy not found, using dummy regulator [ 1.648578] pps pps0: new PPS source ptp0 [ 1.681985] fec 2188000.ethernet eth0: registered PHC device 0 [ 1.688431] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 1.695403] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.705535] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.713008] usbcore: registered new interface driver pegasus [ 1.718763] usbcore: registered new interface driver asix [ 1.724234] usbcore: registered new interface driver ax88179_178a [ 1.730408] usbcore: registered new interface driver cdc_ether [ 1.736334] usbcore: registered new interface driver smsc75xx [ 1.742174] usbcore: registered new interface driver smsc95xx [ 1.747992] usbcore: registered new interface driver net1080 [ 1.753729] usbcore: registered new interface driver cdc_subset [ 1.759716] usbcore: registered new interface driver zaurus [ 1.765404] usbcore: registered new interface driver cdc_ncm [ 1.773597] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.780141] ehci-pci: EHCI PCI platform driver [ 1.784660] ehci-platform: EHCI generic platform driver [ 1.790199] ehci-omap: OMAP-EHCI Host Controller driver [ 1.795652] ehci-orion: EHCI orion driver [ 1.799890] SPEAr-ehci: EHCI SPEAr driver [ 1.804129] ehci-st: EHCI STMicroelectronics driver [ 1.809229] ehci-exynos: EHCI EXYNOS driver [ 1.813662] ehci-atmel: EHCI Atmel driver [ 1.817887] tegra-ehci: Tegra EHCI driver [ 1.822151] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.828363] ohci-pci: OHCI PCI platform driver [ 1.832883] ohci-platform: OHCI generic platform driver [ 1.838431] ohci-omap3: OHCI OMAP3 driver [ 1.842670] SPEAr-ohci: OHCI SPEAr driver [ 1.846911] ohci-st: OHCI STMicroelectronics driver [ 1.852017] ohci-atmel: OHCI Atmel driver [ 1.856797] usbcore: registered new interface driver usb-storage [ 1.868315] ci_hdrc ci_hdrc.0: doesn't support gadget [ 1.873401] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 1.878332] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 [ 1.893302] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 1.899693] hub 1-0:1.0: USB hub found [ 1.903487] hub 1-0:1.0: 1 port detected [ 1.908400] 2184200.usb supply vbus not found, using dummy regulator [ 1.918364] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 1.923341] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [ 1.938302] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 1.944612] hub 2-0:1.0: USB hub found [ 1.948404] hub 2-0:1.0: 1 port detected [ 1.953694] mousedev: PS/2 mouse device common for all mice [ 1.965000] i2c /dev entries driver [ 1.980792] sdhci: Secure Digital Host Controller Interface driver [ 1.986980] sdhci: Copyright(c) Pierre Ossman [ 1.993914] Synopsys Designware Multimedia Card Interface Driver [ 2.001478] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.008019] sdhci-esdhc-imx 2198000.usdhc: could not get ultra high speed state, work on normal mode [ 2.017186] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [ 2.022351] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [ 2.027761] sdhci-esdhc-imx 2198000.usdhc: No vqmmc regulator found [ 2.068526] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 2.076259] sdhci-esdhc-imx 219c000.usdhc: could not get ultra high speed state, work on normal mode [ 2.085426] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO [ 2.091806] sdhci-esdhc-imx 219c000.usdhc: No vqmmc regulator found [ 2.124220] mmc0: new high speed SDHC card at address aaaa [ 2.130232] mmcblk0: mmc0:aaaa SL16G 14.8 GiB [ 2.134772] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [ 2.145295] usbcore: registered new interface driver usbhid [ 2.145602] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 2.145608] GPT:29296874 != 31116287 [ 2.145611] GPT:Alternate GPT header not at the end of the disk. [ 2.145616] GPT:29296874 != 31116287 [ 2.145618] GPT: Use GNU Parted to correct GPT errors. [ 2.145662] mmcblk0: p1 p2 p3 [ 2.178308] usb 2-1: new high-speed USB device number 2 using ci_hdrc [ 2.186088] usbhid: USB HID core driver [ 2.196212] NET: Registered protocol family 10 [ 2.201810] sit: IPv6 over IPv4 tunneling driver [ 2.207199] NET: Registered protocol family 17 [ 2.211671] can: controller area network core (rev 20120528 abi 9) [ 2.217950] NET: Registered protocol family 29 [ 2.222415] can: raw protocol (rev 20120528) [ 2.226703] can: broadcast manager protocol (rev 20120528 t) [ 2.232389] can: netlink gateway (rev 20130117) max_hops=1 [ 2.238557] Key type dns_resolver registered [ 2.243483] ThumbEE CPU extension supported. [ 2.247777] Registering SWP/SWPB emulation handler [ 2.254876] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 2.265407] lcd_panel supply power not found, using dummy regulator [ 2.272986] panel supply power not found, using dummy regulator [ 2.281684] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 2.288504] hctosys: unable to open rtc device (rtc0) [ 2.288698] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 2.292783] lcd_panel supply power not found, using dummy regulator [ 2.294240] panel supply power not found, using dummy regulator [ 2.314730] hub 2-1:1.0: USB hub found [ 2.318648] hub 2-1:1.0: 3 ports detected [ 2.324199] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 2.334969] lcd_panel supply power not found, using dummy regulator [ 2.343183] panel supply power not found, using dummy regulator [ 2.409118] fec 2188000.ethernet eth0: Freescale FEC PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=-1) [ 2.421891] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 2.758274] BUG: scheduling while atomic: swapper/0/0/0x00000002 [ 2.758281] Modules linked in: [ 2.758300] Preemption disabled at:[] schedule_preempt_disabled+0x1c/0x20 [ 2.758302] [ 2.758311] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.302-cip87-rt49 #1 [ 2.758315] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) [ 2.758347] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [ 2.758352] BUG: scheduling while atomic: swapper/1/0/0x00000002 [ 2.758367] [] (show_stack) from [] (dump_stack+0xac/0xc0) [ 2.758371] Modules linked in: [ 2.758387] [] (dump_stack) from [] (__schedule_bug+0x8c/0xa0) [ 2.758398] Preemption disabled at:[] schedule_preempt_disabled+0x1c/0x20 [ 2.758406] [] (__schedule_bug) from [] (__schedule+0x3ac/0x480) [ 2.758407] [ 2.758415] [] (__schedule) from [] (schedule+0x58/0xf4) [ 2.758426] [] (schedule) from [] (rt_spin_lock_slowlock+0x1b4/0x32c) [ 2.758438] [] (rt_spin_lock_slowlock) from [] (imx6q_enter_wait+0x6c/0xb4) [ 2.758455] [] (imx6q_enter_wait) from [] (cpuidle_enter_state+0x258/0x2e0) [ 2.758468] [] (cpuidle_enter_state) from [] (cpu_startup_entry+0x140/0x2c8) [ 2.758487] [] (cpu_startup_entry) from [] (start_kernel+0x39c/0x3b0) [ 2.758498] [] (start_kernel) from [<1020807c>] (0x1020807c) [ 2.758506] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.4.302-cip87-rt49 #1 [ 2.758510] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) [ 2.758529] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [ 2.758541] [] (show_stack) from [] (dump_stack+0xac/0xc0) [ 2.758554] [] (dump_stack) from [] (__schedule_bug+0x8c/0xa0) [ 2.758564] [] (__schedule_bug) from [] (__schedule+0x3ac/0x480) [ 2.758571] [] (__schedule) from [] (schedule+0x58/0xf4) [ 2.758581] [] (schedule) from [] (rt_spin_lock_slowlock+0x1b4/0x32c) [ 2.758593] [] (rt_spin_lock_slowlock) from [] (imx6q_enter_wait+0x14/0xb4) [ 2.758595] ------------[ cut here ]------------ [ 2.758605] [] (imx6q_enter_wait) from [] (cpuidle_enter_state+0x258/0x2e0) [ 2.758621] [] (cpuidle_enter_state) from [] (cpu_startup_entry+0x140/0x2c8) [ 2.758630] [] (cpu_startup_entry) from [<1020abcc>] (0x1020abcc) [ 2.763331] ------------[ cut here ]------------ [ 2.763346] WARNING: CPU: 1 PID: 0 at ../drivers/cpuidle/cpuidle.c:212 cpuidle_enter_state+0x2b8/0x2e0() [ 2.763354] Modules linked in: [ 2.763363] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G W 4.4.302-cip87-rt49 #1 [ 2.763366] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) [ 2.763381] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [ 2.763393] [] (show_stack) from [] (dump_stack+0xac/0xc0) [ 2.763404] [] (dump_stack) from [] (warn_slowpath_common+0x8c/0xa8) [ 2.763419] [] (warn_slowpath_common) from [] (warn_slowpath_null+0x1c/0x24) [ 2.763432] [] (warn_slowpath_null) from [] (cpuidle_enter_state+0x2b8/0x2e0) [ 2.763441] [] (cpuidle_enter_state) from [] (cpu_startup_entry+0x140/0x2c8) [ 2.763448] [] (cpu_startup_entry) from [<1020abcc>] (0x1020abcc) [ 2.763452] ---[ end trace 0000000000000002 ]--- [ 3.084560] WARNING: CPU: 0 PID: 0 at ../drivers/cpuidle/cpuidle.c:212 cpuidle_enter_state+0x2b8/0x2e0() [ 3.094044] Modules linked in: [ 3.097124] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.4.302-cip87-rt49 #1 [ 3.097127] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) [ 3.097148] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [ 3.097163] [] (show_stack) from [] (dump_stack+0xac/0xc0) [ 3.097174] [] (dump_stack) from [] (warn_slowpath_common+0x8c/0xa8) [ 3.097186] [] (warn_slowpath_common) from [] (warn_slowpath_null+0x1c/0x24) [ 3.097197] [] (warn_slowpath_null) from [] (cpuidle_enter_state+0x2b8/0x2e0) [ 3.097208] [] (cpuidle_enter_state) from [] (cpu_startup_entry+0x140/0x2c8) [ 3.097222] [] (cpu_startup_entry) from [] (start_kernel+0x39c/0x3b0) [ 3.097231] [] (start_kernel) from [<1020807c>] (0x1020807c) [ 3.097235] ---[ end trace 0000000000000003 ]--- # # # # #