Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3008 device /dev/ttyimx6q-sabresd-2 [115200 N81] (Debian GNU/Linux) U-Boot 2017.03 (Jan 20 2018 - 10:43:25 +0800) CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 28C Reset cause: POR Model: Freescale i.MX6 Quad Plus SABRE Smart Device Board Board: MX6-SabreSD DRAM: 1 GiB PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 *** Warning - bad CRC, using default environment No panel detected: default to Hannstar-XGA Display: Hannstar-XGA (1024x768) In: serial Out: serial Err: serial flash target is MMC:1 Net: Warning: ethernet@02188000 using MAC address from ROM eth0: ethernet@02188000 [PRIME] Fastboot: Normal Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.205 (1607 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x12000000 1024761/tftp-deploy-c_o0nkdq/kernel/zImage tftp 0x12000000 1024761/tftp-deploy-c_o0nkdq/kernel/zImage Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.205; sending through gateway 172.16.1.4 Filename '1024761/tftp-deploy-c_o0nkdq/kernel/zImage'. Load address: 0x12000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################ 8.7 MiB/s done Bytes transferred = 6602496 (64bf00 hex) => tftp 0x12C00000 1024761/tftp-deploy-c_o0nkdq/ramdisk/ramdisk.cpio.gz.uboot tftp 0x12C00000 1024761/tftp-deploy-c_o0nkdq/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.205; sending through gateway 172.16.1.4 Filename '1024761/tftp-deploy-c_o0nkdq/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x12c00000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################################### 9.9 MiB/s done Bytes transferred = 11034469 (a85f65 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x18000000 1024761/tftp-deploy-c_o0nkdq/dtb/imx6q-sabresd.dtb tftp 0x18000000 1024761/tftp-deploy-c_o0nkdq/dtb/imx6q-sabresd.dtb Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.205; sending through gateway 172.16.1.4 Filename '1024761/tftp-deploy-c_o0nkdq/dtb/imx6q-sabresd.dtb'. Load address: 0x18000000 Loading: *### 5 MiB/s done Bytes transferred = 36410 (8e3a hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x12000000 0x12C00000 0x18000000 bootz 0x12000000 0x12C00000 0x18000000 Kernel image @ 0x12000000 [ 0x000000 - 0x64bf00 ] ## Loading init Ramdisk from Legacy Image at 12c00000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 11034405 Bytes = 10.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 18000000 Booting using the fdt blob at 0x18000000 Using Device Tree in place at 18000000, end 1800be39 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.302-cip70-st20 (KernelCI@build-j434629-arm-gcc-10-multi-v7-defconfig-5zxt7) (gcc version 10.2.1 20210110 (Debian 10.2.1-6) ) #1 SMP Tue Aug 2 07:45:25 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Freescale i.MX6 Quad SABRE Smart Device Board [ 0.000000] bootconsole [uart0] enabled [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] PERCPU: Embedded 11 pages/cpu @ef7ac000 s14860 r8192 d22004 u45056 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 948008K/1048576K available (8645K kernel code, 985K rwdata, 3872K rodata, 1052K init, 320K bss, 35032K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0e426d0 (12522 kB) [ 0.000000] .init : 0xc0e43000 - 0xc0f4a000 (1052 kB) [ 0.000000] .data : 0xc0f4a000 - 0xc10406e0 ( 986 kB) [ 0.000000] .bss : 0xc1043000 - 0xc1093260 ( 321 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=4 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C-310 erratum 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 15ns [ 0.000006] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns [ 0.007834] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns [ 0.019688] Console: colour dummy device 80x30 [ 0.021859] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=330000) [ 0.032280] pid_max: default: 32768 minimum: 301 [ 0.036996] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.043510] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.051131] CPU: Testing write buffer coherency: ok [ 0.055418] CPU0: Spectre v2: using BPIALL workaround [ 0.060746] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.066207] Setting up static identity map for 0x10209000 - 0x10209098 [ 0.076444] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.076449] CPU1: Spectre v2: using BPIALL workaround [ 0.084972] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.084977] CPU2: Spectre v2: using BPIALL workaround [ 0.095685] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.095691] CPU3: Spectre v2: using BPIALL workaround [ 0.105766] Brought up 4 CPUs [ 0.108673] SMP: Total of 4 processors activated (528.00 BogoMIPS). [ 0.114930] CPU: All CPU(s) started in SVC mode. [ 0.120437] devtmpfs: initialized [ 0.130852] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.136335] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns [ 0.145429] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.154787] pinctrl core: initialized pinctrl subsystem [ 0.158887] NET: Registered protocol family 16 [ 0.164460] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.181245] cpuidle: using governor ladder [ 0.196232] cpuidle: using governor menu [ 0.197537] CPU identified as i.MX6Q, silicon rev 1.0 [ 0.221668] No ATAGs? [ 0.221722] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.229098] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.237984] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.244213] Serial: AMBA PL011 UART driver [ 0.248030] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 0.276263] mxs-dma 110000.dma-apbh: initialized [ 0.283216] vgaarb: loaded [ 0.284145] SCSI subsystem initialized [ 0.287280] usbcore: registered new interface driver usbfs [ 0.292352] usbcore: registered new interface driver hub [ 0.297640] usbcore: registered new device driver usb [ 0.304351] pps_core: LinuxPPS API ver. 1 registered [ 0.307611] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.316761] PTP clock support registered [ 0.320871] EDAC MC: Ver: 3.0.0 [ 0.326166] clocksource: Switched to clocksource mxc_timer1 [ 0.339409] NET: Registered protocol family 2 [ 0.341041] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.348618] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.354755] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.361256] TCP: Hash tables configured (established 8192 bind 8192) [ 0.367608] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.373410] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.379903] NET: Registered protocol family 1 [ 0.384386] RPC: Registered named UNIX socket transport module. [ 0.390000] RPC: Registered udp transport module. [ 0.394692] RPC: Registered tcp transport module. [ 0.399387] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.406359] Unpacking initramfs... [ 1.284911] Freeing initrd memory: 10776K [ 1.286494] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 1.306230] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.309968] NFS: Registering the id_resolver key type [ 1.314311] Key type id_resolver registered [ 1.318475] Key type id_legacy registered [ 1.322512] ntfs: driver 2.1.32 [Flags: R/O]. [ 1.328252] bounce: pool size: 64 pages [ 1.330796] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.338036] io scheduler noop registered [ 1.341940] io scheduler deadline registered [ 1.346227] io scheduler cfq registered (default) [ 1.363540] backlight supply power not found, using dummy regulator [ 1.374990] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 1.381650] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 1.427461] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.433340] SuperH (H)SCI(F) driver initialized [ 1.436135] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 24, base_baud = 5000000) is a IMX [ 1.447005] console [ttymxc0] enabled [ 1.447005] console [ttymxc0] enabled [ 1.451480] bootconsole [uart0] disabled [ 1.451480] bootconsole [uart0] disabled [ 1.460351] msm_serial: driver initialized [ 1.466913] STMicroelectronics ASC driver initialized [ 1.473819] [drm] Initialized drm 1.1.0 20060810 [ 1.488446] loop: module loaded [ 1.499999] CAN device driver interface [ 1.505626] 2188000.ethernet supply phy not found, using dummy regulator [ 1.521404] pps pps0: new PPS source ptp0 [ 1.544675] fec 2188000.ethernet eth0: registered PHC device 0 [ 1.550951] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 1.557935] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.567038] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.574504] usbcore: registered new interface driver pegasus [ 1.580236] usbcore: registered new interface driver asix [ 1.585698] usbcore: registered new interface driver ax88179_178a [ 1.591850] usbcore: registered new interface driver cdc_ether [ 1.597766] usbcore: registered new interface driver smsc75xx [ 1.603589] usbcore: registered new interface driver smsc95xx [ 1.609394] usbcore: registered new interface driver net1080 [ 1.615112] usbcore: registered new interface driver cdc_subset [ 1.621088] usbcore: registered new interface driver zaurus [ 1.626751] usbcore: registered new interface driver cdc_ncm [ 1.634222] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.640775] ehci-pci: EHCI PCI platform driver [ 1.645283] ehci-platform: EHCI generic platform driver [ 1.650769] ehci-omap: OMAP-EHCI Host Controller driver [ 1.656183] ehci-orion: EHCI orion driver [ 1.660347] SPEAr-ehci: EHCI SPEAr driver [ 1.664532] ehci-st: EHCI STMicroelectronics driver [ 1.669577] ehci-exynos: EHCI EXYNOS driver [ 1.673951] ehci-atmel: EHCI Atmel driver [ 1.678130] tegra-ehci: Tegra EHCI driver [ 1.682334] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.688546] ohci-pci: OHCI PCI platform driver [ 1.693056] ohci-platform: OHCI generic platform driver [ 1.698479] ohci-omap3: OHCI OMAP3 driver [ 1.702661] SPEAr-ohci: OHCI SPEAr driver [ 1.706845] ohci-st: OHCI STMicroelectronics driver [ 1.711901] ohci-atmel: OHCI Atmel driver [ 1.716525] usbcore: registered new interface driver usb-storage [ 1.724233] imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517 [ 1.731894] imx_usb 2184200.usb: Can't register ci_hdrc platform device, err=-517 [ 1.739936] mousedev: PS/2 mouse device common for all mice [ 1.749590] i2c /dev entries driver [ 1.762421] sdhci: Secure Digital Host Controller Interface driver [ 1.768623] sdhci: Copyright(c) Pierre Ossman [ 1.774938] Synopsys Designware Multimedia Card Interface Driver [ 1.782193] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.788675] sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state, work on normal mode [ 1.797848] sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO [ 1.803016] sdhci-esdhc-imx 2194000.usdhc: Got WP GPIO [ 1.809332] sdhci-esdhc-imx 2194000.usdhc: No vmmc regulator found [ 1.815542] sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found [ 1.856318] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [ 1.864050] sdhci-esdhc-imx 2198000.usdhc: could not get ultra high speed state, work on normal mode [ 1.873226] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [ 1.878392] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [ 1.885681] sdhci-esdhc-imx 2198000.usdhc: No vmmc regulator found [ 1.891884] sdhci-esdhc-imx 2198000.usdhc: No vqmmc regulator found [ 1.931314] mmc1: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 1.940217] sdhci-esdhc-imx 219c000.usdhc: No vmmc regulator found [ 1.948454] sdhci-esdhc-imx 219c000.usdhc: No vqmmc regulator found [ 1.991170] mmc2: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [ 2.000693] ledtrig-cpu: registered to indicate activity on CPUs [ 2.006947] usbcore: registered new interface driver usbhid [ 2.012539] usbhid: USB HID core driver [ 2.021173] NET: Registered protocol family 10 [ 2.026500] sit: IPv6 over IPv4 tunneling driver [ 2.031779] NET: Registered protocol family 17 [ 2.036262] can: controller area network core (rev 20120528 abi 9) [ 2.042686] NET: Registered protocol family 29 [ 2.047174] can: raw protocol (rev 20120528) [ 2.051477] can: broadcast manager protocol (rev 20120528 t) [ 2.057174] can: netlink gateway (rev 20130117) max_hops=1 [ 2.063110] Key type dns_resolver registered [ 2.067528] ThumbEE CPU extension supported. [ 2.071843] Registering SWP/SWPB emulation handler [ 2.078615] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 2.086039] backlight supply power not found, using dummy regulator [ 2.093842] imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517 [ 2.093899] mmc1: new high speed SDHC card at address aaaa [ 2.094379] mmcblk0: mmc1:aaaa SS08G 7.40 GiB [ 2.112542] imx_usb 2184200.usb: Can't register ci_hdrc platform device, err=-517 [ 2.120449] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 2.127617] backlight supply power not found, using dummy regulator [ 2.135324] imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517 [ 2.144115] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 2.150804] hctosys: unable to open rtc device (rtc0) [ 2.151714] imx_usb 2184200.usb: Can't register ci_hdrc platform device, err=-517 [ 2.152119] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 2.153162] backlight supply power not found, using dummy regulator [ 2.154558] imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517 [ 2.205385] mmc2: new DDR MMC card at address 0001 [ 2.210753] mmcblk1: mmc2:0001 Q2J55L 7.13 GiB [ 2.215562] mmcblk1boot0: mmc2:0001 Q2J55L partition 1 2.00 MiB [ 2.221762] mmcblk1boot1: mmc2:0001 Q2J55L partition 2 2.00 MiB [ 2.227943] mmcblk1rpmb: mmc2:0001 Q2J55L partition 3 4.00 MiB [ 2.237533] imx_usb 2184200.usb: Can't register ci_hdrc platform device, err=-517 [ 2.245512] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 2.252730] backlight supply power not found, using dummy regulator [ 2.260464] imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517 [ 2.261722] fec 2188000.ethernet eth0: Freescale FEC PHY driver [Atheros 8031 ethernet] (mii_bus:phy_addr=2188000.ethernet-1:01, irq=-1) [ 2.261795] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 6.261629] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 6.271188] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.286255] Sending DHCP requests .., OK [ 9.016164] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.205 [ 9.023773] IP-Config: Complete: [ 9.027027] device=eth0, hwaddr=00:04:9f:05:b8:b4, ipaddr=172.16.1.205, mask=255.255.255.0, gw=172.16.1.4 [ 9.037044] host=172.16.1.205, domain=example.org, nis-domain=(none) [ 9.043847] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= [ 9.049864] nameserver0=172.16.1.4 [ 9.054132] usb_otg_vbus: disabling [ 9.057654] usb_h1_vbus: disabling [ 9.061060] wm8962-supply: disabling [ 9.067265] Freeing unused kernel memory: 1052K [ 9.098557] devpts: called with bogus options Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 9.187489] udevd[112]: starting version 3.2.9 [ 9.192891] random: udevd: uninitialized urandom read (16 bytes read, 7 bits of entropy available) [ 9.202227] random: udevd: uninitialized urandom read (16 bytes read, 7 bits of entropy available) [ 9.211309] random: udevd: uninitialized urandom read (16 bytes read, 7 bits of entropy available) [ 9.228772] udevd[112]: specified user 'tss' unknown [ 9.233922] udevd[112]: specified group 'tss' unknown [ 9.241368] udevd[113]: starting eudev-3.2.9 [ 9.479580] random: udevd: uninitialized urandom read (16 bytes read, 7 bits of entropy available) done Saving random seed: [ 9.827220] random: dd: uninitialized urandom read (512 bytes read, 43 bits of entropy available) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: [ 9.912126] random: dropbear: uninitialized urandom read (32 bytes read, 43 bits of entropy available) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1024761/environment . /lava-1024761/environment / # /lava-1024761/bin/lava-test-runner /lava-1024761/0 /lava-1024761/bin/lava-test-runner /lava-1024761/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1024761/0/tests/0_dme[ 15.730405] sg + cat uuid + UUID=1024761_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 15.769362] [ 15.806482] [ 15.843114] + set +x [ 15.852574] # / # #export SHELL=/bin/sh / # export SHELL=/bin/sh. /lava-1024761/environment / # . /lava-1024761/environment/lava-1024761/bin/lava-test-runner /lava-1024761/1 / # /lava-1024761/bin/lava-test-runner /lava-1024761/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1024761/1/tests/1_boo[ 21.579066] trr + cat uuid + UUID=1024761_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-1024761/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-1024761/1/../bin/lava-test-case [ 21.610899] /lava-1024761/1/../bin/lava-test-case [ 21.648091] /lava-1024761/1/../bin/lava-test-case [ 21.671486] + set +x [ 21.688913] / #