[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.38 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12435239/tftp-deploy-er30olq_/kernel/zImage tftp 0x10000000 12435239/tftp-deploy-er30olq_/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '12435239/tftp-deploy-er30olq_/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 14.5 MiB/s done Bytes transferred = 6608280 (64d598 hex) => tftp 0x14000000 12435239/tftp-deploy-er30olq_/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12435239/tftp-deploy-er30olq_/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '12435239/tftp-deploy-er30olq_/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################### 14.5 MiB/s done Bytes transferred = 7123042 (6cb062 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12435239/tftp-deploy-er30olq_/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12435239/tftp-deploy-er30olq_/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '12435239/tftp-deploy-er30olq_/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4.4 MiB/s done Bytes transferred = 36559 (8ecf hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12435239/extract-nfsrootfs-wqrx7ss7,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12435239/extract-nfsrootfs-wqrx7ss7,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' =>bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x64d598 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 7122978 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0bece Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.302-cip83 (KernelCI@build-j64503-arm-gcc-10-multi-v7-defconfig-bkf4f) (gcc version 10.2.1 20210110 (Debian 10.2.1-6) ) #1 SMP Wed Jan 3 07:35:08 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] bootconsole [uart0] enabled [ 0.000000] Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] PERCPU: Embedded 11 pages/cpu @ef7ac000 s14860 r8192 d22004 u45056 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12435239/extract-nfsrootfs-wqrx7ss7,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 951812K/1048576K available (8653K kernel code, 986K rwdata, 3872K rodata, 1052K init, 320K bss, 31228K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0e44760 (12530 kB) [ 0.000000] .init : 0xc0e45000 - 0xc0f4c000 (1052 kB) [ 0.000000] .data : 0xc0f4c000 - 0xc10429a0 ( 987 kB) [ 0.000000] .bss : 0xc1045000 - 0xc1095258 ( 321 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=4 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C-310 erratum 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000006] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.008183] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.020134] Console: colour dummy device 80x30 [ 0.022294] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=15000) [ 0.032454] pid_max: default: 32768 minimum: 301 [ 0.037170] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.043682] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.051318] CPU: Testing write buffer coherency: ok [ 0.055590] CPU0: Spectre v2: using BPIALL workaround [ 0.060906] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.066380] Setting up static identity map for 0x10209000 - 0x10209098 [ 0.076651] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.076657] CPU1: Spectre v2: using BPIALL workaround [ 0.085183] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.085189] CPU2: Spectre v2: using BPIALL workaround [ 0.095897] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.095902] CPU3: Spectre v2: using BPIALL workaround [ 0.105973] Brought up 4 CPUs [ 0.108883] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.115052] CPU: All CPU(s) started in SVC mode. [ 0.120580] devtmpfs: initialized [ 0.130870] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.136361] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns [ 0.145450] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.154850] pinctrl core: initialized pinctrl subsystem [ 0.159024] NET: Registered protocol family 16 [ 0.164840] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.181129] cpuidle: using governor ladder [ 0.196121] cpuidle: using governor menu [ 0.197449] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.222871] No ATAGs? [ 0.222924] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.230302] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.239099] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.245515] Serial: AMBA PL011 UART driver [ 0.249229] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 0.276322] mxs-dma 110000.dma-apbh: initialized [ 0.283374] vgaarb: loaded [ 0.284324] SCSI subsystem initialized [ 0.287433] usbcore: registered new interface driver usbfs [ 0.292514] usbcore: registered new interface driver hub [ 0.297798] usbcore: registered new device driver usb [ 0.304615] pps_core: LinuxPPS API ver. 1 registered [ 0.307770] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.316919] PTP clock support registered [ 0.321043] EDAC MC: Ver: 3.0.0 [ 0.326432] clocksource: Switched to clocksource mxc_timer1 [ 0.339470] NET: Registered protocol family 2 [ 0.341097] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.348719] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.354823] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.361298] TCP: Hash tables configured (established 8192 bind 8192) [ 0.367685] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.373474] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.379969] NET: Registered protocol family 1 [ 0.384462] RPC: Registered named UNIX socket transport module. [ 0.390063] RPC: Registered udp transport module. [ 0.394756] RPC: Registered tcp transport module. [ 0.399445] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.406458] Unpacking initramfs... [ 0.915380] Freeing initrd memory: 6960K [ 0.916918] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.936623] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.940360] NFS: Registering the id_resolver key type [ 0.944716] Key type id_resolver registered [ 0.948844] Key type id_legacy registered [ 0.952914] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.958678] bounce: pool size: 64 pages [ 0.961187] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.968434] io scheduler noop registered [ 0.972336] io scheduler deadline registered [ 0.976622] io scheduler cfq registered (default) [ 1.003193] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 1.009854] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 1.055458] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.061408] SuperH (H)SCI(F) driver initialized [ 1.064222] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 24, base_baud = 5000000) is a IMX [ 1.072709] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 295, base_baud = 5000000) is a IMX [ 1.083702] console [ttymxc1] enabled [ 1.083702] console [ttymxc1] enabled [ 1.088174] bootconsole [uart0] disabled [ 1.088174] bootconsole [uart0] disabled [ 1.096923] msm_serial: driver initialized [ 1.103637] STMicroelectronics ASC driver initialized [ 1.110631] [drm] Initialized drm 1.1.0 20060810 [ 1.118680] lcd_panel supply power not found, using dummy regulator [ 1.125169] panel supply power not found, using dummy regulator [ 1.138107] loop: module loaded [ 1.150001] CAN device driver interface [ 1.155666] 2188000.ethernet supply phy not found, using dummy regulator [ 1.171662] pps pps0: new PPS source ptp0 [ 1.193312] fec 2188000.ethernet eth0: registered PHC device 0 [ 1.199603] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 1.206594] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.215709] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.223189] usbcore: registered new interface driver pegasus [ 1.228931] usbcore: registered new interface driver asix [ 1.234402] usbcore: registered new interface driver ax88179_178a [ 1.240558] usbcore: registered new interface driver cdc_ether [ 1.246486] usbcore: registered new interface driver smsc75xx [ 1.252314] usbcore: registered new interface driver smsc95xx [ 1.258132] usbcore: registered new interface driver net1080 [ 1.263857] usbcore: registered new interface driver cdc_subset [ 1.269838] usbcore: registered new interface driver zaurus [ 1.275507] usbcore: registered new interface driver cdc_ncm [ 1.283088] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.289644] ehci-pci: EHCI PCI platform driver [ 1.294156] ehci-platform: EHCI generic platform driver [ 1.299652] ehci-omap: OMAP-EHCI Host Controller driver [ 1.305063] ehci-orion: EHCI orion driver [ 1.309258] SPEAr-ehci: EHCI SPEAr driver [ 1.313462] ehci-st: EHCI STMicroelectronics driver [ 1.318527] ehci-exynos: EHCI EXYNOS driver [ 1.322920] ehci-atmel: EHCI Atmel driver [ 1.327110] tegra-ehci: Tegra EHCI driver [ 1.331314] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.337531] ohci-pci: OHCI PCI platform driver [ 1.342046] ohci-platform: OHCI generic platform driver [ 1.347487] ohci-omap3: OHCI OMAP3 driver [ 1.351687] SPEAr-ohci: OHCI SPEAr driver [ 1.355863] ohci-st: OHCI STMicroelectronics driver [ 1.360929] ohci-atmel: OHCI Atmel driver [ 1.365596] usbcore: registered new interface driver usb-storage [ 1.376460] ci_hdrc ci_hdrc.0: doesn't support gadget [ 1.381548] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 1.386466] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 [ 1.401446] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 1.407638] hub 1-0:1.0: USB hub found [ 1.411460] hub 1-0:1.0: 1 port detected [ 1.415988] 2184200.usb supply vbus not found, using dummy regulator [ 1.425786] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 1.430713] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [ 1.446458] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 1.452572] hub 2-0:1.0: USB hub found [ 1.456358] hub 2-0:1.0: 1 port detected [ 1.461241] mousedev: PS/2 mouse device common for all mice [ 1.471107] i2c /dev entries driver [ 1.484515] sdhci: Secure Digital Host Controller Interface driver [ 1.490716] sdhci: Copyright(c) Pierre Ossman [ 1.497186] Synopsys Designware Multimedia Card Interface Driver [ 1.504484] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.510947] sdhci-esdhc-imx 2198000.usdhc: could not get ultra high speed state, work on normal mode [ 1.520125] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [ 1.525293] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [ 1.530715] sdhci-esdhc-imx 2198000.usdhc: No vqmmc regulator found [ 1.571563] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 1.579240] sdhci-esdhc-imx 219c000.usdhc: could not get ultra high speed state, work on normal mode [ 1.588411] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO [ 1.594766] sdhci-esdhc-imx 219c000.usdhc: No vqmmc regulator found [ 1.624902] mmc0: new high speed SDHC card at address 0001 [ 1.630829] mmcblk0: mmc0:0001 SD 14.6 GiB [ 1.636663] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [ 1.646100] ledtrig-cpu: registered to indicate activity on CPUs [ 1.652351] usbcore: registered new interface driver usbhid [ 1.653985] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 1.653989] GPT:29296874 != 30560255 [ 1.653991] GPT:Alternate GPT header not at the end of the disk. [ 1.653994] GPT:29296874 != 30560255 [ 1.653996] GPT: Use GNU Parted to correct GPT errors. [ 1.654037] mmcblk0: p1 p2 p3 [ 1.686741] usbhid: USB HID core driver [ 1.695724] NET: Registered protocol family 10 [ 1.700995] sit: IPv6 over IPv4 tunneling driver [ 1.706248] NET: Registered protocol family 17 [ 1.710733] can: controller area network core (rev 20120528 abi 9) [ 1.717146] NET: Registered protocol family 29 [ 1.721619] can: raw protocol (rev 20120528) [ 1.725900] can: broadcast manager protocol (rev 20120528 t) [ 1.731585] can: netlink gateway (rev 20130117) max_hops=1 [ 1.736461] usb 2-1: new high-speed USB device number 2 using ci_hdrc [ 1.743927] Key type dns_resolver registered [ 1.748659] ThumbEE CPU extension supported. [ 1.752959] Registering SWP/SWPB emulation handler [ 1.759584] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 1.769131] lcd_panel supply power not found, using dummy regulator [ 1.776445] panel supply power not found, using dummy regulator [ 1.784054] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 1.790710] hctosys: unable to open rtc device (rtc0) [ 1.791657] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 1.794798] lcd_panel supply power not found, using dummy regulator [ 1.795782] panel supply power not found, using dummy regulator [ 1.892075] fec 2188000.ethernet eth0: Freescale FEC PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=-1) [ 1.904861] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 1.912010] hub 2-1:1.0: USB hub found [ 1.915838] hub 2-1:1.0: 3 ports detected [ 1.921242] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 1.930729] lcd_panel supply power not found, using dummy regulator [ 1.938042] panel supply power not found, using dummy regulator [ 5.891926] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 5.899474] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 5.911505] Sending DHCP requests ., OK [ 5.941459] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.38 [ 5.949501] IP-Config: Complete: [ 5.952748] device=eth0, hwaddr=00:19:b8:08:f0:fe, ipaddr=192.168.201.38, mask=255.255.255.0, gw=192.168.201.1 [ 5.963199] host=imx6q-sabrelite-lava-cbg-8, domain=lava-rack, nis-domain=(none) [ 5.971042] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 5.978101] nameserver0=192.168.201.1 [ 5.982544] CAN XCVR: disabling [ 5.988487] Freeing unused kernel memory: 1052K Loading, please wait... Starting version 247.3-7+deb11u2 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f0:fe mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.38 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-8 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 7.893107] systemd[1]: System time before build time, advancing clock. [ 8.022286] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 8.046007] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 8.067991] systemd[1]: Set hostname to . [ 8.906698] systemd[1]: Queued start job for default target Graphical Interface. [ 8.915562] random: systemd: uninitialized urandom read (16 bytes read, 125 bits of entropy available) [ 8.925086] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 8.937467] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 8.946557] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 8.966644] random: systemd: uninitialized urandom read (16 bytes read, 126 bits of entropy available) [ 8.976444] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 8.996613] random: systemd: uninitialized urandom read (16 bytes read, 126 bits of entropy available) [ 9.006337] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 9.026592] random: systemd: uninitialized urandom read (16 bytes read, 126 bits of entropy available) [ 9.036206] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 9.056650] random: systemd: uninitialized urandom read (16 bytes read, 126 bits of entropy available) [ 9.066245] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 9.091609] random: systemd: uninitialized urandom read (16 bytes read, 126 bits of entropy available) [ 9.101189] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 9.121768] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 9.133579] random: systemd: uninitialized urandom read (16 bytes read, 127 bits of entropy available) [ 9.142961] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 9.161910] random: systemd: uninitialized urandom read (16 bytes read, 127 bits of entropy available) [ 9.171294] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 9.186643] random: systemd: uninitialized urandom read (16 bytes read, 127 bits of entropy available) [ 9.196024] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 9.211591] random: systemd: uninitialized urandom read (16 bytes read, 127 bits of entropy available) [ 9.220982] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 9.236741] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 9.252127] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 9.286245] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 9.295614] systemd[1]: Listening on Journal Socket (/dev/log). [ 9.296439] random: nonblocking pool is initialized [ OK ] Listening on Journal Socket (/dev/log). [ 9.317286] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 9.337660] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 9.357999] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 9.377208] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 9.397135] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 9.405805] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 9.431874] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 9.447113] systemd[1]: Condition check resulted in Kernel Trace File System being skipped. [ 9.459825] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 9.485705] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 9.505930] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 9.526011] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 9.555634] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 9.570477] systemd[1]: Starting Journal Service... Starting Journal Service... [ 9.600526] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 9.667274] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 9.691844] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 9.729052] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 9.747605] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 9.788444] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... Starting Create System Users... [ 9.991467] systemd-journald[163]: Received client request to flush runtime journal. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ 11.233604] proc: unrecognized mount option "hidepid=invisible" or missing value [ 11.392391] proc: unrecognized mount option "hidepid=invisible" or missing value [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Network Name Resolution... [ 12.588538] proc: unrecognized mount option "hidepid=invisible" or missing value [ 12.684170] proc: unrecognized mount option "hidepid=invisible" or missing value [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.4.302-cip83 #1 SMP Wed Jan 3 07:35:08 UTC 2024 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12435239/extract-nfsrootfs-wqrx7ss7' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12435239/extract-nfsrootfs-wqrx7ss7' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-12435239/environment . /lava-12435239/environment / # /lava-12435239/bin/lava-test-runner /lava-12435239/0 /lava-12435239/bin/lava-test-runner /lava-12435239/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-12435239/0/tests/0_timesync-off ++ cat uuid + UUID=12435239_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-12435239/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=12435239_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u None -L '' -S /dev/null -b imx6q-sabrelite -g cip -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2024-01-03 07:43:28-- http://none/ Resolving none (none)... failed: Name or service not known. wget: unable to resolve host address 'none' tar: None: Cannot open: No such file or directory tar: Error is not recoverable: exiting now ./kselftest.sh: 160: cd: can't cd to kselftest / #