[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12711567/tftp-deploy-1zd423iz/kernel/zImage tftp 0x10000000 12711567/tftp-deploy-1zd423iz/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '12711567/tftp-deploy-1zd423iz/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 6.3 MiB/s done Bytes transferred = 6608264 (64d588 hex) => tftp 0x14000000 12711567/tftp-deploy-1zd423iz/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12711567/tftp-deploy-1zd423iz/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '12711567/tftp-deploy-1zd423iz/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################### 5.8 MiB/s done Bytes transferred = 7123264 (6cb140 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12711567/tftp-deploy-1zd423iz/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12711567/tftp-deploy-1zd423iz/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '12711567/tftp-deploy-1zd423iz/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5 MiB/s done Bytes transferred = 36559 (8ecf hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12711567/extract-nfsrootfs-zgqvkc1j,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12711567/extract-nfsrootfs-zgqvkc1j,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x64d588 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 7123200 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0bece Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.302-cip84 (KernelCI@build-j101045-arm-gcc-10-multi-v7-defconfig-kds8h) (gcc version 10.2.1 20210110 (Debian 10.2.1-6) ) #1 SMP Wed Feb 7 04:58:36 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] bootconsole [uart0] enabled [ 0.000000] Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] PERCPU: Embedded 11 pages/cpu @ef7ac000 s14860 r8192 d22004 u45056 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12711567/extract-nfsrootfs-zgqvkc1j,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 951812K/1048576K available (8653K kernel code, 986K rwdata, 3872K rodata, 1052K init, 320K bss, 31228K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0e44768 (12530 kB) [ 0.000000] .init : 0xc0e45000 - 0xc0f4c000 (1052 kB) [ 0.000000] .data : 0xc0f4c000 - 0xc10429a0 ( 987 kB) [ 0.000000] .bss : 0xc1045000 - 0xc1095258 ( 321 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=4 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C-310 erratum 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.008183] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.020148] Console: colour dummy device 80x30 [ 0.022294] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=15000) [ 0.032455] pid_max: default: 32768 minimum: 301 [ 0.037169] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.043684] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.051316] CPU: Testing write buffer coherency: ok [ 0.055591] CPU0: Spectre v2: using BPIALL workaround [ 0.060910] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.066381] Setting up static identity map for 0x10209000 - 0x10209098 [ 0.076627] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.076633] CPU1: Spectre v2: using BPIALL workaround [ 0.085150] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.085155] CPU2: Spectre v2: using BPIALL workaround [ 0.095868] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.095874] CPU3: Spectre v2: using BPIALL workaround [ 0.105948] Brought up 4 CPUs [ 0.108856] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.115029] CPU: All CPU(s) started in SVC mode. [ 0.120553] devtmpfs: initialized [ 0.130817] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.136309] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns [ 0.145396] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.154805] pinctrl core: initialized pinctrl subsystem [ 0.158959] NET: Registered protocol family 16 [ 0.164729] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.181157] cpuidle: using governor ladder [ 0.196149] cpuidle: using governor menu [ 0.197475] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.222731] No ATAGs? [ 0.222783] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.230162] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.238913] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.245254] Serial: AMBA PL011 UART driver [ 0.249008] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 0.276269] mxs-dma 110000.dma-apbh: initialized [ 0.283433] vgaarb: loaded [ 0.284376] SCSI subsystem initialized [ 0.287489] usbcore: registered new interface driver usbfs [ 0.292570] usbcore: registered new interface driver hub [ 0.297857] usbcore: registered new device driver usb [ 0.304650] pps_core: LinuxPPS API ver. 1 registered [ 0.307830] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.316977] PTP clock support registered [ 0.321101] EDAC MC: Ver: 3.0.0 [ 0.326476] clocksource: Switched to clocksource mxc_timer1 [ 0.339527] NET: Registered protocol family 2 [ 0.341153] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.348773] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.354877] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.361367] TCP: Hash tables configured (established 8192 bind 8192) [ 0.367735] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.373532] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.380027] NET: Registered protocol family 1 [ 0.384519] RPC: Registered named UNIX socket transport module. [ 0.390118] RPC: Registered udp transport module. [ 0.394809] RPC: Registered tcp transport module. [ 0.399501] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.406514] Unpacking initramfs... [ 0.914450] Freeing initrd memory: 6960K [ 0.915954] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.935659] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.939429] NFS: Registering the id_resolver key type [ 0.943742] Key type id_resolver registered [ 0.947875] Key type id_legacy registered [ 0.951949] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.957760] bounce: pool size: 64 pages [ 0.960223] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.967469] io scheduler noop registered [ 0.971359] io scheduler deadline registered [ 0.975658] io scheduler cfq registered (default) [ 1.001849] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 1.008506] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 1.065353] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.071312] SuperH (H)SCI(F) driver initialized [ 1.074104] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 24, base_baud = 5000000) is a IMX [ 1.082622] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 295, base_baud = 5000000) is a IMX [ 1.093601] console [ttymxc1] enabled [ 1.093601] console [ttymxc1] enabled [ 1.098074] bootconsole [uart0] disabled [ 1.098074] bootconsole [uart0] disabled [ 1.106803] msm_serial: driver initialized [ 1.113525] STMicroelectronics ASC driver initialized [ 1.120487] [drm] Initialized drm 1.1.0 20060810 [ 1.128563] lcd_panel supply power not found, using dummy regulator [ 1.135038] panel supply power not found, using dummy regulator [ 1.147975] loop: module loaded [ 1.159704] CAN device driver interface [ 1.165347] 2188000.ethernet supply phy not found, using dummy regulator [ 1.181711] pps pps0: new PPS source ptp0 [ 1.203744] fec 2188000.ethernet eth0: registered PHC device 0 [ 1.210017] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 1.217001] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.226056] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.233529] usbcore: registered new interface driver pegasus [ 1.239266] usbcore: registered new interface driver asix [ 1.244727] usbcore: registered new interface driver ax88179_178a [ 1.250878] usbcore: registered new interface driver cdc_ether [ 1.256793] usbcore: registered new interface driver smsc75xx [ 1.262621] usbcore: registered new interface driver smsc95xx [ 1.268435] usbcore: registered new interface driver net1080 [ 1.274159] usbcore: registered new interface driver cdc_subset [ 1.280136] usbcore: registered new interface driver zaurus [ 1.285801] usbcore: registered new interface driver cdc_ncm [ 1.293313] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.299868] ehci-pci: EHCI PCI platform driver [ 1.304375] ehci-platform: EHCI generic platform driver [ 1.309861] ehci-omap: OMAP-EHCI Host Controller driver [ 1.315261] ehci-orion: EHCI orion driver [ 1.319447] SPEAr-ehci: EHCI SPEAr driver [ 1.323656] ehci-st: EHCI STMicroelectronics driver [ 1.328718] ehci-exynos: EHCI EXYNOS driver [ 1.333100] ehci-atmel: EHCI Atmel driver [ 1.337288] tegra-ehci: Tegra EHCI driver [ 1.341503] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.347714] ohci-pci: OHCI PCI platform driver [ 1.352226] ohci-platform: OHCI generic platform driver [ 1.357672] ohci-omap3: OHCI OMAP3 driver [ 1.361856] SPEAr-ohci: OHCI SPEAr driver [ 1.366025] ohci-st: OHCI STMicroelectronics driver [ 1.371082] ohci-atmel: OHCI Atmel driver [ 1.375746] usbcore: registered new interface driver usb-storage [ 1.386989] ci_hdrc ci_hdrc.0: doesn't support gadget [ 1.392080] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 1.396994] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 [ 1.411506] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 1.417699] hub 1-0:1.0: USB hub found [ 1.421494] hub 1-0:1.0: 1 port detected [ 1.426027] 2184200.usb supply vbus not found, using dummy regulator [ 1.435826] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 1.440743] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [ 1.456502] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 1.462631] hub 2-0:1.0: USB hub found [ 1.466419] hub 2-0:1.0: 1 port detected [ 1.471305] mousedev: PS/2 mouse device common for all mice [ 1.481095] i2c /dev entries driver [ 1.494252] sdhci: Secure Digital Host Controller Interface driver [ 1.500452] sdhci: Copyright(c) Pierre Ossman [ 1.506904] Synopsys Designware Multimedia Card Interface Driver [ 1.514179] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.520626] sdhci-esdhc-imx 2198000.usdhc: could not get ultra high speed state, work on normal mode [ 1.529802] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [ 1.534967] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [ 1.540352] sdhci-esdhc-imx 2198000.usdhc: No vqmmc regulator found [ 1.581629] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 1.589297] sdhci-esdhc-imx 219c000.usdhc: could not get ultra high speed state, work on normal mode [ 1.598475] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO [ 1.604833] sdhci-esdhc-imx 219c000.usdhc: No vqmmc regulator found [ 1.651623] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [ 1.660957] ledtrig-cpu: registered to indicate activity on CPUs [ 1.667046] mmc0: new high speed SDHC card at address e624 [ 1.667192] usbcore: registered new interface driver usbhid [ 1.667194] usbhid: USB HID core driver [ 1.672186] NET: Registered protocol family 10 [ 1.686996] mmcblk0: mmc0:e624 SL16G 14.8 GiB [ 1.687159] sit: IPv6 over IPv4 tunneling driver [ 1.687815] NET: Registered protocol family 17 [ 1.687831] can: controller area network core (rev 20120528 abi 9) [ 1.688029] NET: Registered protocol family 29 [ 1.688041] can: raw protocol (rev 20120528) [ 1.688051] can: broadcast manager protocol (rev 20120528 t) [ 1.688064] can: netlink gateway (rev 20130117) max_hops=1 [ 1.688475] Key type dns_resolver registered [ 1.691771] ThumbEE CPU extension supported. [ 1.691786] Registering SWP/SWPB emulation handler [ 1.700956] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 1.704311] lcd_panel supply power not found, using dummy regulator [ 1.705293] panel supply power not found, using dummy regulator [ 1.706981] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 1.707269] hctosys: unable to open rtc device (rtc0) [ 1.711816] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 1.715405] lcd_panel supply power not found, using dummy regulator [ 1.716597] panel supply power not found, using dummy regulator [ 1.756511] usb 2-1: new high-speed USB device number 2 using ci_hdrc [ 1.797110] fec 2188000.ethernet eth0: Freescale FEC PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=-1) [ 1.809897] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 1.815403] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 1.815407] GPT:7812499 != 31116287 [ 1.815409] GPT:Alternate GPT header not at the end of the disk. [ 1.815412] GPT:7812499 != 31116287 [ 1.815414] GPT: Use GNU Parted to correct GPT errors. [ 1.815456] mmcblk0: p1 p2 p3 [ 1.816633] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 1.819932] lcd_panel supply power not found, using dummy regulator [ 1.820919] panel supply power not found, using dummy regulator [ 1.937619] hub 2-1:1.0: USB hub found [ 1.941499] hub 2-1:1.0: 3 ports detected [ 1.946816] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 1.956041] lcd_panel supply power not found, using dummy regulator [ 1.963344] panel supply power not found, using dummy regulator [ 5.796988] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 5.804531] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 5.816547] Sending DHCP requests ., OK [ 5.846503] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 [ 5.854543] IP-Config: Complete: [ 5.857790] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 [ 5.868242] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) [ 5.876085] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 5.883145] nameserver0=192.168.201.1 [ 5.887593] CAN XCVR: disabling [ 5.893592] Freeing unused kernel memory: 1052K Loading, please wait... Starting version 247.3-7+deb11u2 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f0:fd mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.37 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-7 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 7.749145] systemd[1]: System time before build time, advancing clock. [ 7.872243] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 7.895997] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 7.918175] systemd[1]: Set hostname to . [ 8.706445] systemd[1]: Queued start job for default target Graphical Interface. [ 8.715107] random: systemd: uninitialized urandom read (16 bytes read, 127 bits of entropy available) [ 8.724619] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 8.736996] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 8.746046] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 8.761675] random: systemd: uninitialized urandom read (16 bytes read, 127 bits of entropy available) [ 8.771444] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 8.791641] random: systemd: uninitialized urandom read (16 bytes read, 128 bits of entropy available) [ 8.801358] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 8.821657] random: systemd: uninitialized urandom read (16 bytes read, 128 bits of entropy available) [ 8.831272] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 8.851690] random: systemd: uninitialized urandom read (16 bytes read, 128 bits of entropy available) [ 8.856480] random: nonblocking pool is initialized [ 8.866190] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 8.891891] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 8.916841] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 8.928729] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 8.946932] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 8.961730] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 8.981695] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 8.996780] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 9.012103] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 9.049609] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 9.059304] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 9.077365] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 9.097737] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 9.118255] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 9.137253] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 9.157153] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 9.165849] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 9.201866] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 9.217119] systemd[1]: Condition check resulted in Kernel Trace File System being skipped. [ 9.229629] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 9.255459] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 9.275587] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 9.295145] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 9.337283] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 9.382560] systemd[1]: Starting Journal Service... Starting Journal Service... [ 9.414062] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 9.434567] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 9.460188] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 9.490682] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 9.507878] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 9.571445] systemd[1]: modprobe@configfs.service: Succeeded. [ 9.578385] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 9.598636] systemd[1]: modprobe@drm.service: Succeeded. [ 9.604589] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. [ 9.622791] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ 9.822093] systemd-journald[162]: Received client request to flush runtime journal. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Create Volatile Files and Directories. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ 11.318615] proc: unrecognized mount option "hidepid=invisible" or missing value [ 11.498972] proc: unrecognized mount option "hidepid=invisible" or missing value [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ 11.788393] proc: unrecognized mount option "hidepid=invisible" or missing value [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ 12.673685] proc: unrecognized mount option "hidepid=invisible" or missing value [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.4.302-cip84 #1 SMP Wed Feb 7 04:58:36 UTC 2024 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12711567/extract-nfsrootfs-zgqvkc1j' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12711567/extract-nfsrootfs-zgqvkc1j' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-12711567/environment . /lava-12711567/environment / # /lava-12711567/bin/lava-test-runner /lava-12711567/0 /lava-12711567/bin/lava-test-runner /lava-12711567/0 + export TESTRUN_ID=0_dmesg + cd /lava-12711567/0/tests/0_dmesg + cat uuid + UUID=12711567_1.6.2.4.1 + set +[ 23.525354] x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 23.594792] [ 23.651617] [ 23.708298] + set +x [ 23.717439] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-12711567/environment / # . /lava-12711567/environment/lava-12711567/bin/lava-test-runner /lava-12711567/1 / # /lava-12711567/bin/lava-test-runner /lava-12711567/1 + export TESTRUN_ID=1_bootrr + cd /lava-12711567/1/tests/1_bootrr + cat uuid + UUID=12711567_1.6.2.4.5 + set +[ 24.249885] x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-12711567/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-12711567/1/../bin/lava-test-case [ 24.295189] /lava-12711567/1/../bin/lava-test-case [ 24.351807] /lava-12711567/1/../bin/lava-test-case [ 24.381921] + set +x [ 24.404967] / #