[Enter `^Ec?' for help] U-Boot SPL 2015.10-00025-g943d444 (Feb 19 2016 - 15:04:45) U-Boot 2015.10-00025-g943d444 (Feb 19 2016 - 15:04:45 +0000) Model: Radxa Rock 2 Square DRAM: 2 GiB MMC: dwmmc@ff0c0000: 0, dwmmc@ff0f0000: 1 In: serial@ff690000 Out: serial@ff690000 Err: serial@ff690000 Incorrect eeprom header Net: eth0: ethernet@ff290000 Hit any key to stop autoboot: 1  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp ethernet@ff290000 Waiting for PHY auto negotiation to complete...... done Speed: 1000, full duplex BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.201.22 (761 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x2000000 12714086/tftp-deploy-y1h3p6eu/kernel/zImage tftp 0x2000000 12714086/tftp-deploy-y1h3p6eu/kernel/zImage Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '12714086/tftp-deploy-y1h3p6eu/kernel/zImage'. Load address: 0x2000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 3.5 MiB/s done Bytes transferred = 6608264 (64d588 hex) => tftp 0x4000000 12714086/tftp-deploy-y1h3p6eu/ramdisk/ramdisk.cpio.gz.uboot tftp 0x4000000 12714086/tftp-deploy-y1h3p6eu/ramdisk/ramdisk.cpio.gz.uboot Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '12714086/tftp-deploy-y1h3p6eu/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x4000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################### 3.4 MiB/s done Bytes transferred = 11042384 (a87e50 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x1f00000 12714086/tftp-deploy-y1h3p6eu/dtb/rk3288-rock2-square.dtb tftp 0x1f00000 12714086/tftp-deploy-y1h3p6eu/dtb/rk3288-rock2-square.dtb Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '12714086/tftp-deploy-y1h3p6eu/dtb/rk3288-rock2-square.dtb'. Load address: 0x1f00000 Loading: *### 3.2 MiB/s done Bytes transferred = 30437 (76e5 hex) => setenv bootargs 'console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x2000000 0x4000000 0x1f00000 bootz 0x2000000 0x4000000 0x1f00000 Kernel image @ 0x2000000 [ 0x000000 - 0x64d588 ] ## Loading init Ramdisk from Legacy Image at 04000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 11042320 Bytes = 10.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01f00000 Booting using the fdt blob at 0x1f00000 Using Device Tree in place at 01f00000, end 01f0a6e4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x500 [ 0.000000] Linux version 4.4.302-cip84 (KernelCI@build-j102153-arm-gcc-10-multi-v7-defconfig-cvxfn) (gcc version 10.2.1 20210110 (Debian 10.2.1-6) ) #1 SMP Wed Feb 7 19:35:47 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Radxa Rock 2 Square [ 0.000000] Malformed early option 'earlycon' [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] PERCPU: Embedded 11 pages/cpu @eefaa000 s14860 r8192 d22004 u45056 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522752 [ 0.000000] Kernel command line: console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1988376K/2097152K available (8653K kernel code, 986K rwdata, 3872K rodata, 1052K init, 320K bss, 43240K reserved, 65536K cma-reserved, 1245184K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0e44768 (12530 kB) [ 0.000000] .init : 0xc0e45000 - 0xc0f4c000 (1052 kB) [ 0.000000] .data : 0xc0f4c000 - 0xc10429a0 ( 987 kB) [ 0.000000] .bss : 0xc1045000 - 0xc1095258 ( 321 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=4 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C: failed to init: -19 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000021] Switching to timer-based delay loop, resolution 41ns [ 0.003087] Console: colour dummy device 80x30 [ 0.003115] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=120000) [ 0.003130] pid_max: default: 32768 minimum: 301 [ 0.003247] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003261] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003878] CPU: Testing write buffer coherency: ok [ 0.003908] CPU0: Spectre v2: using BPIALL workaround [ 0.004113] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500 [ 0.004323] Setting up static identity map for 0x209000 - 0x209098 [ 0.009103] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501 [ 0.009109] CPU1: Spectre v2: using BPIALL workaround [ 0.010728] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502 [ 0.010734] CPU2: Spectre v2: using BPIALL workaround [ 0.012344] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503 [ 0.012350] CPU3: Spectre v2: using BPIALL workaround [ 0.012442] Brought up 4 CPUs [ 0.012455] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.012462] CPU: All CPU(s) started in SVC mode. [ 0.013795] devtmpfs: initialized [ 0.023162] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0 [ 0.023817] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns [ 0.023846] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.025842] pinctrl core: initialized pinctrl subsystem [ 0.027596] NET: Registered protocol family 16 [ 0.029669] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.045070] cpuidle: using governor ladder [ 0.060085] cpuidle: using governor menu [ 0.076383] No ATAGs? [ 0.076419] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.076429] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.080084] Serial: AMBA PL011 UART driver [ 0.112432] iommu: Adding device ff930000.vop to group 0 [ 0.112509] iommu: Adding device ff940000.vop to group 1 [ 0.113041] vgaarb: loaded [ 0.114024] SCSI subsystem initialized [ 0.114529] usbcore: registered new interface driver usbfs [ 0.114606] usbcore: registered new interface driver hub [ 0.114659] usbcore: registered new device driver usb [ 0.116089] pps_core: LinuxPPS API ver. 1 registered [ 0.116099] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.116130] PTP clock support registered [ 0.116334] EDAC MC: Ver: 3.0.0 [ 0.118680] clocksource: Switched to clocksource arch_sys_counter [ 0.130452] NET: Registered protocol family 2 [ 0.130601] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.131624] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.131707] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.131896] TCP: Hash tables configured (established 8192 bind 8192) [ 0.131959] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.132009] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.132208] NET: Registered protocol family 1 [ 0.132496] RPC: Registered named UNIX socket transport module. [ 0.132507] RPC: Registered udp transport module. [ 0.132514] RPC: Registered tcp transport module. [ 0.132521] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.132940] Unpacking initramfs... [ 1.163991] Freeing initrd memory: 10784K [ 1.164307] hw perfevents: enabled with armv7_cortex_a12 PMU driver, 7 counters available [ 1.177894] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.178840] NFS: Registering the id_resolver key type [ 1.178872] Key type id_resolver registered [ 1.178881] Key type id_legacy registered [ 1.178962] ntfs: driver 2.1.32 [Flags: R/O]. [ 1.180453] bounce: pool size: 64 pages [ 1.180685] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.180707] io scheduler noop registered [ 1.180724] io scheduler deadline registered [ 1.180766] io scheduler cfq registered (default) [ 1.194537] dma-pl330 ff250000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.194556] dma-pl330 ff250000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16 [ 1.195339] dma-pl330 ffb20000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.195357] dma-pl330 ffb20000.dma-controller: DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10 [ 1.260876] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.263255] console [ttyS2] disabled [ 1.263294] ff690000.serial: ttyS2 at MMIO 0xff690000 (irq = 32, base_baud = 1500000) is a 16550A [ 1.925438] console [ttyS2] enabled [ 1.929947] SuperH (H)SCI(F) driver initialized [ 1.935333] msm_serial: driver initialized [ 1.939942] STMicroelectronics ASC driver initialized [ 1.946532] [drm] Initialized drm 1.1.0 20060810 [ 1.960280] loop: module loaded [ 1.971143] CAN device driver interface [ 1.976231] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 1.983206] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.990973] rk_gmac-dwmac ff290000.ethernet: phy regulator is not available yet, deferred probing [ 2.001322] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.008794] usbcore: registered new interface driver pegasus [ 2.014543] usbcore: registered new interface driver asix [ 2.020011] usbcore: registered new interface driver ax88179_178a [ 2.026168] usbcore: registered new interface driver cdc_ether [ 2.032082] usbcore: registered new interface driver smsc75xx [ 2.037909] usbcore: registered new interface driver smsc95xx [ 2.043727] usbcore: registered new interface driver net1080 [ 2.049452] usbcore: registered new interface driver cdc_subset [ 2.055441] usbcore: registered new interface driver zaurus [ 2.061117] usbcore: registered new interface driver cdc_ncm [ 2.068404] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.074954] ehci-pci: EHCI PCI platform driver [ 2.079468] ehci-platform: EHCI generic platform driver [ 2.084987] ehci-omap: OMAP-EHCI Host Controller driver [ 2.090373] ehci-orion: EHCI orion driver [ 2.094538] SPEAr-ehci: EHCI SPEAr driver [ 2.098703] ehci-st: EHCI STMicroelectronics driver [ 2.103738] ehci-exynos: EHCI EXYNOS driver [ 2.108081] ehci-atmel: EHCI Atmel driver [ 2.112244] tegra-ehci: Tegra EHCI driver [ 2.116429] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.122637] ohci-pci: OHCI PCI platform driver [ 2.127157] ohci-platform: OHCI generic platform driver [ 2.132553] ohci-omap3: OHCI OMAP3 driver [ 2.136718] SPEAr-ohci: OHCI SPEAr driver [ 2.140885] ohci-st: OHCI STMicroelectronics driver [ 2.145920] ohci-atmel: OHCI Atmel driver [ 2.150483] usbcore: registered new interface driver usb-storage [ 2.157992] mousedev: PS/2 mouse device common for all mice [ 2.167403] i2c /dev entries driver [ 2.172040] rk3x-i2c ff170000.i2c: using default SCL frequency: 100000 [ 2.179086] rk3x-i2c ff170000.i2c: Initialized RK3xxx I2C bus at f08b2000 [ 2.186015] rk3x-i2c ff650000.i2c: using default SCL frequency: 100000 [ 2.218336] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected! [ 2.229510] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected! [ 2.239627] rk3x-i2c ff650000.i2c: Initialized RK3xxx I2C bus at f08b4000 [ 2.253722] vdd_cpu: supplied by vcc_sys [ 2.260258] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 500000 KHz [ 2.270706] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 600000 KHz [ 2.282620] sdhci: Secure Digital Host Controller Interface driver [ 2.288797] sdhci: Copyright(c) Pierre Ossman [ 2.293631] Synopsys Designware Multimedia Card Interface Driver [ 2.299948] dwmmc_rockchip ff0c0000.dwmmc: IDMAC supports 32-bit address mode. [ 2.307188] dwmmc_rockchip ff0c0000.dwmmc: Using internal DMA controller. [ 2.313971] dwmmc_rockchip ff0c0000.dwmmc: Version ID is 270a [ 2.319725] dwmmc_rockchip ff0c0000.dwmmc: DW MMC controller at irq 29,32 bit host data width,256 deep fifo [ 2.329480] VCC_IO: supplied by vcc_sys [ 2.333804] vcc_sd: supplied by VCC_IO [ 2.338614] VCCIO_SD: supplied by VCC_IO [ 2.358688] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 2.378680] dwmmc_rockchip ff0c0000.dwmmc: 1 slots initialized [ 2.384674] dwmmc_rockchip ff0f0000.dwmmc: IDMAC supports 32-bit address mode. [ 2.391904] dwmmc_rockchip ff0f0000.dwmmc: Using internal DMA controller. [ 2.398686] dwmmc_rockchip ff0f0000.dwmmc: Version ID is 270a [ 2.404439] dwmmc_rockchip ff0f0000.dwmmc: DW MMC controller at irq 30,32 bit host data width,256 deep fifo [ 2.414672] dwmmc_rockchip ff0f0000.dwmmc: No vqmmc regulator found [ 2.420980] dwmmc_rockchip ff0f0000.dwmmc: allocated mmc-pwrseq [ 2.438900] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 2.458684] dwmmc_rockchip ff0f0000.dwmmc: 1 slots initialized [ 2.464771] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.471136] ledtrig-cpu: registered to indicate activity on CPUs [ 2.477238] usbcore: registered new interface driver usbhid [ 2.482808] usbhid: USB HID core driver [ 2.488568] NET: Registered protocol family 10 [ 2.493365] sit: IPv6 over IPv4 tunneling driver [ 2.498285] NET: Registered protocol family 17 [ 2.502740] can: controller area network core (rev 20120528 abi 9) [ 2.509008] NET: Registered protocol family 29 [ 2.513451] can: raw protocol (rev 20120528) [ 2.517724] can: broadcast manager protocol (rev 20120528 t) [ 2.523386] can: netlink gateway (rev 20130117) max_hops=1 [ 2.529046] Key type dns_resolver registered [ 2.533353] ThumbEE CPU extension supported. [ 2.537632] Registering SWP/SWPB emulation handler [ 2.546443] VCCIO_PMU: supplied by vcc_sys [ 2.551533] rk_gmac-dwmac ff290000.ethernet: clock input or output? (input). [ 2.558577] rk_gmac-dwmac ff290000.ethernet: TX delay(0x30). [ 2.564230] rk_gmac-dwmac ff290000.ethernet: RX delay(0x10). [ 2.569885] rk_gmac-dwmac ff290000.ethernet: init for RGMII [ 2.572503] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 2.572813] mmc1: new high speed MMC card at address 0001 [ 2.573008] mmcblk0: mmc1:0001 032GE4 29.1 GiB [ 2.573079] mmcblk0boot0: mmc1:0001 032GE4 partition 1 4.00 MiB [ 2.573147] mmcblk0boot1: mmc1:0001 032GE4 partition 2 4.00 MiB [ 2.575396] mmcblk0: p1 p2 [ 2.609730] rk_gmac-dwmac ff290000.ethernet: clock input from PHY [ 2.620838] stmmac - user ID: 0x10, Synopsys ID: 0x35 [ 2.625884] Ring mode enabled [ 2.628932] DMA HW capability register supported [ 2.633452] Normal descriptors [ 2.636771] RX Checksum Offload Engine supported (type 2) [ 2.642248] TX Checksum insertion supported [ 2.646510] Wake-Up On Lan supported [ 2.650185] eth%d: device MAC address 4a:01:9c:e5:04:ff [ 2.655401] Enable RX Mitigation via HW Watchdog Timer [ 2.722362] eth%d: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active [ 2.728804] eth%d: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01) [ 2.736538] hctosys: unable to open rtc device (rtc0) [ 2.773677] Sending DHCP requests .. [ 7.749220] rk_gmac-dwmac ff290000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 9.383737] ., OK [ 9.419074] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.22 [ 9.427258] IP-Config: Complete: [ 9.430552] device=eth0, hwaddr=4a:01:9c:e5:04:ff, ipaddr=192.168.201.22, mask=255.255.255.0, gw=192.168.201.1 [ 9.441022] host=rk3288-rock2-square-cbg-0, domain=lava-rack, nis-domain=(none) [ 9.448800] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 9.455877] nameserver0=192.168.201.1 [ 9.460503] vcc_sd: disabling [ 9.465252] ttyS2 - failed to request DMA [ 9.473125] Freeing unused kernel memory: 1052K [ 9.523106] devpts: called with bogus options Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 9.559017] udevd[108]: starting version 3.2.9 [ 9.563924] random: udevd: uninitialized urandom read (16 bytes read, 9 bits of entropy available) [ 9.572988] random: udevd: uninitialized urandom read (16 bytes read, 9 bits of entropy available) [ 9.582057] random: udevd: uninitialized urandom read (16 bytes read, 9 bits of entropy available) [ 9.594953] udevd[108]: specified user 'tss' unknown [ 9.599975] udevd[108]: specified group 'tss' unknown [ 9.606015] udevd[109]: starting eudev-3.2.9 [ 9.707224] random: udevd: uninitialized urandom read (16 bytes read, 9 bits of entropy available) [ 9.730734] ehci-platform ff500000.usb: EHCI Host Controller [ 9.736421] ehci-platform ff500000.usb: new USB bus registered, assigned bus number 1 [ 9.750465] rtc-hym8563 0-0051: no valid clock/calendar values available [ 9.762862] rtc-hym8563 0-0051: rtc core: registered hym8563 as rtc0 [ 9.773407] ehci-platform ff500000.usb: irq 35, io mem 0xff500000 [ 9.789858] ehci-platform ff500000.usb: USB 2.0 started, EHCI 1.00 [ 9.812539] hub 1-0:1.0: USB hub found [ 9.816776] hub 1-0:1.0: 1 port detected done Saving random seed: [ 9.892975] random: dd: uninitialized urandom read (512 bytes read, 35 bits of entropy available) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: [ 9.931839] random: dropbear: uninitialized urandom read (32 bytes read, 35 bits of entropy available) OK /bin/sh: can't access tty; job control turned off / # / # # [ 10.048714] usb 1-1: new high-speed USB device number 2 using ehci-platform # / # export SHELL=/bin/sh [ 10.187309] hub 1-1:1.0: USB hub found [ 10.191488] hub 1-1:1.0: 4 ports detected export SHELL=/bin/sh / # . /lava-12714086/environment . /lava-12714086/environment / # /lava-12714086/bin/lava-test-runner /lava-12714086/0 /lava-12714086/bin/lava-test-runner /lava-12714086/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-12714086/0/tests/0_dmesg + cat uuid [ 10.544429] + UUID=12714086_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 10.585314] [ 10.622105] [ 10.645256] + set +x [ 10.654326] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-12714086/environment / # . /lava-12714086/environment/lava-12714086/bin/lava-test-runner /lava-12714086/1 / # /lava-12714086/bin/lava-test-runner /lava-12714086/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-12714086/1/tests/1_bootrr + cat uuid [ 11.227036] + UUID=12714086_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-12714086/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-12714086/1/../bin/lav[ 11.254068] a-test-case /lava-12714086/1/../bin/lava-test-case [ 11.283860] /lava-12714086/1/../bin/lava-test-case [ 11.302745] /lava-12714086/1/../bin/lava-test-case [ 12.359192] /lava-12714086/1/../bin/lava-test-case [ 13.410494] /lava-12714086/1/../bin/lava-test-case [ 14.474805] /lava-12714086/1/../bin/lava-test-case [ 15.529028] /lava-12714086/1/../bin/lava-test-case [ 15.557715] /lava-12714086/1/../bin/lava-test-case [ 15.579065] + set +x [ 15.586792] / #