Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'.  U-Boot SPL 2020.10 (Apr 28 2023 - 11:09:01 +0100) Trying to boot from MMC2 U-Boot 2020.10 (Apr 28 2023 - 11:09:01 +0100) CPU : AM335X-GP rev 2.1 Model: TI AM335x BeagleBone Black DRAM: 512 MiB WDT: Started with servicing (60s timeout) MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from FAT... Unable to use mmc 1:1... not set. Validating first E-fuse MAC Net: eth2: ethernet@4a100000, eth3: usb_ether Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.1.23 (1067 ms) => setenv serverip 192.168.1.1 setenv serverip 192.168.1.1 => tftp 0x82000000 1204503/tftp-deploy-j44ewki1/kernel/zImage tftp 0x82000000 1204503/tftp-deploy-j44ewki1/kernel/zImage link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 192.168.1.1; our IP address is 192.168.1.23 Filename '1204503/tftp-deploy-j44ewki1/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ########################################################## 2.2 MiB/s done Bytes transferred = 3712856 (38a758 hex) => tftp 0x83000000 1204503/tftp-deploy-j44ewki1/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1204503/tftp-deploy-j44ewki1/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 192.168.1.1; our IP address is 192.168.1.23 Filename '1204503/tftp-deploy-j44ewki1/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################### 2.1 MiB/s done Bytes transferred = 11125500 (a9c2fc hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1204503/tftp-deploy-j44ewki1/dtb/am335x-boneblack.dtb tftp 0x88000000 1204503/tftp-deploy-j44ewki1/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 192.168.1.1; our IP address is 192.168.1.23 Filename '1204503/tftp-deploy-j44ewki1/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *### 1.8 MiB/s done Bytes transferred = 33561 (8319 hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2024-10-09 12:01:10 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 11125436 Bytes = 10.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8800b318 fixing up phy_id for ethernet1, old: 1, new: -1644830584 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.302-cip92 (KernelCI@build-j338475-arm-gcc-12-omap2plus-defconfig-9znsv) (gcc version 12.2.0 (Debian 12.2.0-14) ) #1 SMP Wed Oct 9 11:37:58 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI AM335x BeagleBone Black [ 0.000000] Malformed early option 'earlycon' [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon ) [ 0.000000] PERCPU: Embedded 13 pages/cpu @df915000 s20648 r8192 d24408 u53248 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129408 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 470924K/522240K available (6951K kernel code, 752K rwdata, 2232K rodata, 448K init, 8189K bss, 34932K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08fff30 (9184 kB) [ 0.000000] .init : 0xc0900000 - 0xc0970000 ( 448 kB) [ 0.000000] .data : 0xc0970000 - 0xc0a2c368 ( 753 kB) [ 0.000000] .bss : 0xc0a2f000 - 0xc122e718 (8190 kB) [ 0.000000] Running RCU self tests [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU lockdep checking is enabled. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000015] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000038] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000081] OMAP clocksource: timer1 at 24000000 Hz [ 0.000493] clocksource_probe: no matching clocksources found [ 0.001321] Console: colour dummy device 80x30 [ 0.001379] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001388] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001396] ... MAX_LOCK_DEPTH: 48 [ 0.001403] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001411] ... CLASSHASH_SIZE: 4096 [ 0.001418] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001424] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001432] ... CHAINHASH_SIZE: 32768 [ 0.001439] memory used by lock dependency info: 5167 kB [ 0.001447] per task-struct memory footprint: 1536 bytes [ 0.001474] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) [ 0.078739] pid_max: default: 32768 minimum: 301 [ 0.079134] Security Framework initialized [ 0.079248] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.079261] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.082030] Initializing cgroup subsys io [ 0.082126] Initializing cgroup subsys memory [ 0.082214] Initializing cgroup subsys devices [ 0.082322] Initializing cgroup subsys freezer [ 0.082392] Initializing cgroup subsys perf_event [ 0.082457] CPU: Testing write buffer coherency: ok [ 0.082598] CPU0: Spectre v2: using BPIALL workaround [ 0.083970] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.084091] Setting up static identity map for 0x80008280 - 0x800082f0 [ 0.087651] Brought up 1 CPUs [ 0.087675] SMP: Total of 1 processors activated (996.14 BogoMIPS). [ 0.087686] CPU: All CPU(s) started in SVC mode. [ 0.091608] devtmpfs: initialized [ 0.125653] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.176086] omap_hwmod: debugss: _wait_target_disable failed [ 0.231286] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.231355] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.233612] pinctrl core: initialized pinctrl subsystem [ 0.238610] NET: Registered protocol family 16 [ 0.243704] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.245826] cpuidle: using governor ladder [ 0.245856] cpuidle: using governor menu [ 0.257228] OMAP GPIO hardware version 0.1 [ 0.278429] No ATAGs? [ 0.278463] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.318977] edma 49000000.edma: TI EDMA DMA engine driver [ 0.322967] SCSI subsystem initialized [ 0.324866] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring probe [ 0.324975] omap_i2c 4819c000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c2_pins, deferring probe [ 0.325228] pps_core: LinuxPPS API ver. 1 registered [ 0.325238] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.325288] PTP clock support registered [ 0.329461] clocksource: Switched to clocksource timer1 [ 0.455591] NET: Registered protocol family 2 [ 0.456094] IP idents hash table entries: 8192 (order: 4, 65536 bytes) [ 0.457839] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.457926] TCP bind hash table entries: 4096 (order: 5, 147456 bytes) [ 0.458488] TCP: Hash tables configured (established 4096 bind 4096) [ 0.458708] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.458803] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.459318] NET: Registered protocol family 1 [ 0.461087] RPC: Registered named UNIX socket transport module. [ 0.461110] RPC: Registered udp transport module. [ 0.461119] RPC: Registered tcp transport module. [ 0.461129] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.462846] Trying to unpack rootfs image as initramfs... [ 1.388732] Freeing initrd memory: 10868K [ 1.389777] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 1.394188] audit: initializing netlink subsys (disabled) [ 1.394496] audit: type=2000 audit(1.390:1): initialized [ 1.399118] VFS: Disk quotas dquot_6.6.0 [ 1.399765] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.402214] NFS: Registering the id_resolver key type [ 1.402572] Key type id_resolver registered [ 1.402588] Key type id_legacy registered [ 1.402792] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.408214] io scheduler noop registered [ 1.408249] io scheduler deadline registered [ 1.408305] io scheduler cfq registered (default) [ 1.410538] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 1.413578] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled [ 1.420727] omap_uart 44e09000.serial: no wakeirq for uart0 [ 1.421370] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 158, base_baud = 3000000) is a OMAP UART0 [ 2.164487] console [ttyO0] enabled [ 2.203250] brd: module loaded [ 2.227912] loop: module loaded [ 2.233790] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.309492] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.315879] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.345295] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.356353] cpsw 4a100000.ethernet: Detected MACID = f4:b8:98:ab:fa:84 [ 2.368503] mousedev: PS/2 mouse device common for all mice [ 2.374530] i2c /dev entries driver [ 2.380855] omap_hsmmc 48060000.mmc: Got CD GPIO [ 2.459865] ledtrig-cpu: registered to indicate activity on CPUs [ 2.467333] oprofile: using arm/armv7 [ 2.472119] Initializing XFRM netlink socket [ 2.477077] NET: Registered protocol family 10 [ 2.485117] sit: IPv6 over IPv4 tunneling driver [ 2.492312] NET: Registered protocol family 17 [ 2.497047] NET: Registered protocol family 15 [ 2.502177] Key type dns_resolver registered [ 2.506810] omap_voltage_late_init: Voltage driver support not added [ 2.513526] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize [ 2.522019] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize [ 2.531211] ThumbEE CPU extension supported. [ 2.535712] Registering SWP/SWPB emulation handler [ 2.540798] SmartReflex Class3 initialized [ 2.596707] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 2.603218] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 2.613386] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz [ 2.621051] hctosys: unable to open rtc device (rtc0) [ 2.626426] sr_init: No PMIC hook to init smartreflex [ 2.632018] sr_init: platform driver register failed for SR [ 2.657090] net eth0: initializing cpsw version 1.12 (0) [ 2.665225] net eth0: phy found : id is : 0x7c0f1 [ 2.670322] libphy: PHY 4a101000.mdio:9df5e088 not found [ 2.675872] net eth0: phy \"4a101000.mdio:9df5e088\" not found on slave 1, err -19 [ 2.692524] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 2.699058] mmc1: new high speed MMC card at address 0001 [ 2.707686] mmcblk0: mmc1:0001 MK2704 3.53 GiB [ 2.713822] mmcblk0boot0: mmc1:0001 MK2704 partition 1 2.00 MiB [ 2.720960] mmcblk0boot1: mmc1:0001 MK2704 partition 2 2.00 MiB [ 2.731128] mmcblk0: p1 [ 6.700198] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 6.709552] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.729445] Sending DHCP requests ., OK [ 6.749982] IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.23 [ 6.757988] IP-Config: Complete: [ 6.761433] device=eth0, hwaddr=f4:b8:98:ab:fa:84, ipaddr=192.168.1.23, mask=255.255.255.0, gw=192.168.1.1 [ 6.771997] host=192.168.1.23, domain=example.org, nis-domain=(none) [ 6.779084] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= [ 6.785375] nameserver0=192.168.1.1 [ 6.793789] Freeing unused kernel memory: 448K [ 6.876693] devpts: called with bogus options Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 7.198054] udevd[103]: starting version 3.2.9 [ 7.205651] random: udevd: uninitialized urandom read (16 bytes read, 11 bits of entropy available) [ 7.216614] random: udevd: uninitialized urandom read (16 bytes read, 11 bits of entropy available) [ 7.226466] random: udevd: uninitialized urandom read (16 bytes read, 11 bits of entropy available) [ 7.248661] udevd[103]: specified user 'tss' unknown [ 7.254452] udevd[103]: specified group 'tss' unknown [ 7.268932] udevd[104]: starting eudev-3.2.9 [ 7.922326] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 7.970448] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 7.992716] 47401300.usb-phy supply vcc not found, using dummy regulator [ 8.003498] 47401b00.usb-phy supply vcc not found, using dummy regulator [ 8.210705] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20 [ 8.776167] usbcore: registered new interface driver usbfs [ 8.782712] usbcore: registered new interface driver hub [ 8.788452] usbcore: registered new device driver usb [ 8.901457] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 8.908223] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1 [ 9.046400] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 9.053693] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.061307] usb usb1: Product: MUSB HDRC host driver [ 9.066498] usb usb1: Manufacturer: Linux 4.4.302-cip92 musb-hcd [ 9.072824] usb usb1: SerialNumber: musb-hdrc.1.auto [ 9.207395] hub 1-0:1.0: USB hub found [ 9.234496] hub 1-0:1.0: 1 port detected done Saving random seed: [ 9.552448] random: dd: uninitialized urandom read (512 bytes read, 26 bits of entropy available) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: [ 9.774235] random: dropbear: uninitialized urandom read (32 bytes read, 27 bits of entropy available) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1204503/environment . /lava-1204503/environment / # /lava-1204503/bin/lava-test-runner /lava-1204503/0 /lava-1204503/bin/lava-test-runner /lava-1204503/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1204503/0/tests/0_dmesg + cat uuid + UUID=1204503_1.5.2.4.1 + set +x [ 10.728277] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh kern :crit : clocksource_probe: no matching clocksources found [ 10.835551] [ 10.930136] [ 11.022337] + set +x [ 11.034715] / #