connecting to NetworkSerialPort(target=Target(name='dove-cubox-0', env=None), name='NetworkSerialPort', state=, avail=True, host='moxa.cuskci.stw.pengutronix.de', port=4015, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t moxa.cuskci.stw.pengutronix.de:4015 connected to 10.8.254.5 (port 4015) Escape character: Ctrl-\ Type the escape character to get to the prompt. barebox 2020.06.0-00092-gc130f9ac29 #2 Fri Jul 3 17:13:59 CEST 2020 Board: Marvell Dove SoC: Marvell 0510 rev 7 mdio_bus: miibus0: probed [33mWARNING:[0m m25p80 spi-flash@00: found n25q032, expected w25q32 m25p80 spi-flash@00: n25q032 (4096 Kbytes) dove-sdhci f1092000.sdio-host@92000.of: registered as mci0 mci0: detected SD card version 2.0 mci0: registered disk0 malloc space: 0x1fefe1a0 -> 0x3fdfc33f (size 511 MiB) envfs: no envfs (magic mismatch) - envfs never written? [?25h Hit m for menu or any to stop autoboot: 3 [1;32mbarebox@[1;36mMarvell Dove:/[0m bootm -v -r /mnt/tftp/969018/tftp-deploy-7zngt79z/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/969018/tftp-deploy-7zngt79z/dtb/dove-cubox.dtb /mnt/tftp/969018/tftp-deploy-7zngt79z/kernel/zImage -a 0x05000000 -L 0x04000000 [1;32mbarebox@[1;36mMarvell Dove:/[0m bootm -v -r /mnt/tftp/969018/tftp-deploy-7zngt79z/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/969018/tftp-deploy-7zngt79z/dtb/dove-cubox.dtb /mnt/tftp/969018/tftp-deploy-7zngt79z/kernel/zImage -a 0x05000000 -L 0x04000000 eth0: 1000Mbps full duplex link detected [33mWARNING:[0m eth0: No MAC address set. Using random address be:4a:be:c3:22:c2 T eth0: DHCP client bound to address 10.8.254.155 Loading ARM Linux zImage '/mnt/tftp/969018/tftp-deploy-7zngt79z/kernel/zImage' OS image not yet relocated Passing control to ARM zImage handler Loaded initrd GZIP compressed '/mnt/tftp/969018/tftp-deploy-7zngt79z/ramdisk/ramdisk.cpio.gz' initrd is at 0x04000000-0x04a88e4b Loading devicetree from '/mnt/tftp/969018/tftp-deploy-7zngt79z/dtb/dove-cubox.dtb' commandline: console=ttyS0,115200n8 earlyprintk Starting kernel at 0x05000000, initrd at 0x04000000, oftree at 0x04a89000... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.302-cip76 (KernelCI@build-j1615554-arm-gcc-10-multi-v7-defconfig-hzq98) (gcc version 10.2.1 20210110 (Debian 10.2.1-6) ) #1 SMP Tue Jun 6 13:54:39 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [560f5815] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: SolidRun CuBox [ 0.000000] cma: Reserved 64 MiB at 0x3c000000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] PERCPU: Embedded 11 pages/cpu @ef7dc000 s14860 r8192 d22004 u45056 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 948184K/1048576K available (8649K kernel code, 985K rwdata, 3872K rodata, 1048K init, 320K bss, 34856K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0e43738 (12526 kB) [ 0.000000] .init : 0xc0e44000 - 0xc0f4a000 (1048 kB) [ 0.000000] .data : 0xc0f4a000 - 0xc1040740 ( 986 kB) [ 0.000000] .bss : 0xc1043000 - 0xc1093260 ( 321 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000008] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.001216] Console: colour dummy device 80x30 [ 0.001245] Calibrating delay loop... 791.34 BogoMIPS (lpj=1978368) [ 0.030025] pid_max: default: 32768 minimum: 301 [ 0.030164] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.030180] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.030867] CPU: Testing write buffer coherency: ok [ 0.031139] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.031227] Setting up static identity map for 0x209000 - 0x209098 [ 0.033609] Brought up 1 CPUs [ 0.033626] SMP: Total of 1 processors activated (791.34 BogoMIPS). [ 0.033633] CPU: All CPU(s) started in SVC mode. [ 0.034266] devtmpfs: initialized [ 0.039440] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 5 [ 0.040012] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns [ 0.040097] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.044943] pinctrl core: initialized pinctrl subsystem [ 0.046862] NET: Registered protocol family 16 [ 0.049013] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.050887] cpuidle: using governor ladder [ 0.050910] cpuidle: using governor menu [ 0.051184] Dove 88AP510 SoC [ 0.051204] Tauros2: Disabling L2 prefetch. [ 0.051211] Tauros2: Disabling line fill burt8. [ 0.051217] Tauros2: Enabling L2 cache. [ 0.051223] Tauros2: L2 cache support initialised in ARMv7 mode. [ 0.059578] No ATAGs? [ 0.059602] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.062422] Serial: AMBA PL011 UART driver [ 0.075837] reg-fixed-voltage regulators:regulator@1: could not find pctldev for node /mbus/internal-regs/power-management@d0000/pin-ctrl@0200/pmx-gpio-1, deferring probe [ 0.077952] vgaarb: loaded [ 0.078890] SCSI subsystem initialized [ 0.079386] usbcore: registered new interface driver usbfs [ 0.079457] usbcore: registered new interface driver hub [ 0.079516] usbcore: registered new device driver usb [ 0.080653] pps_core: LinuxPPS API ver. 1 registered [ 0.080662] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.080691] PTP clock support registered [ 0.080855] EDAC MC: Ver: 3.0.0 [ 0.083076] clocksource: Switched to clocksource orion_clocksource [ 0.093603] NET: Registered protocol family 2 [ 0.093744] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.094655] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.094733] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.094836] TCP: Hash tables configured (established 8192 bind 8192) [ 0.094922] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.094955] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.095106] NET: Registered protocol family 1 [ 0.095434] RPC: Registered named UNIX socket transport module. [ 0.095444] RPC: Registered udp transport module. [ 0.095451] RPC: Registered tcp transport module. [ 0.095458] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.095822] Unpacking initramfs... [ 0.880633] Freeing initrd memory: 10788K [ 0.896068] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.897033] NFS: Registering the id_resolver key type [ 0.897075] Key type id_resolver registered [ 0.897083] Key type id_legacy registered [ 0.897150] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.898654] bounce: pool size: 64 pages [ 0.898904] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.898922] io scheduler noop registered [ 0.898936] io scheduler deadline registered [ 0.898972] io scheduler cfq registered (default) [ 0.903123] dove-pinctrl f10d0200.pin-ctrl: falling back to hardcoded PMU resource [ 0.903267] dove-pinctrl f10d0200.pin-ctrl: [Firmware Bug]: Missing pinctrl regs in DTB. Please update your firmware. [ 0.903925] dove-pinctrl f10d0200.pin-ctrl: registered pinctrl driver [ 0.906567] irq: Cannot allocate irq_descs @ IRQ39, assuming pre-allocated [ 0.906912] irq: Cannot allocate irq_descs @ IRQ71, assuming pre-allocated [ 0.910151] mv_xor f1060800.dma-engine: Marvell shared XOR driver [ 0.934249] mv_xor f1060800.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.934461] mv_xor f1060900.dma-engine: Marvell shared XOR driver [ 0.959234] mv_xor f1060900.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.021651] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.023861] SuperH (H)SCI(F) driver initialized [ 1.024487] msm_serial: driver initialized [ 1.025106] console [ttyS0] disabled [ 1.025157] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 21, base_baud = 10416666) is a 16550A [ 1.670417] console [ttyS0] enabled [ 1.674534] STMicroelectronics ASC driver initialized [ 1.680733] [drm] Initialized drm 1.1.0 20060810 [ 1.693456] loop: module loaded [ 1.698649] sata_mv f10a0000.sata-host: slots 32 ports 1 [ 1.705671] scsi host0: sata_mv [ 1.709123] ata1: SATA max UDMA/133 irq 30 [ 1.715761] m25p80 spi0.0: found n25q032, expected w25q32 [ 1.721180] m25p80 spi0.0: n25q032 (4096 Kbytes) [ 1.725808] 2 ofpart partitions found on MTD device spi0.0 [ 1.731281] Creating 2 MTD partitions on \"spi0.0\": [ 1.736063] 0x000000000000-0x000000200000 : \"barebox\" [ 1.742245] 0x000000200000-0x000000220000 : \"env\" [ 1.751500] CAN device driver interface [ 1.756291] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 1.763238] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.788339] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 1.797013] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address be:4a:be:c3:22:c2 [ 1.807625] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.815081] usbcore: registered new interface driver pegasus [ 1.820812] usbcore: registered new interface driver asix [ 1.826255] usbcore: registered new interface driver ax88179_178a [ 1.832386] usbcore: registered new interface driver cdc_ether [ 1.838274] usbcore: registered new interface driver smsc75xx [ 1.844079] usbcore: registered new interface driver smsc95xx [ 1.849871] usbcore: registered new interface driver net1080 [ 1.855569] usbcore: registered new interface driver cdc_subset [ 1.861528] usbcore: registered new interface driver zaurus [ 1.867181] usbcore: registered new interface driver cdc_ncm [ 1.874100] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.880628] ehci-pci: EHCI PCI platform driver [ 1.885124] ehci-platform: EHCI generic platform driver [ 1.890475] ehci-omap: OMAP-EHCI Host Controller driver [ 1.895795] ehci-orion: EHCI orion driver [ 1.899947] orion-ehci f1050000.usb-host: EHCI Host Controller [ 1.905796] orion-ehci f1050000.usb-host: new USB bus registered, assigned bus number 1 [ 1.914031] orion-ehci f1050000.usb-host: irq 25, io mem 0xf1050000 [ 1.928099] orion-ehci f1050000.usb-host: USB 2.0 started, EHCI 1.00 [ 1.935281] hub 1-0:1.0: USB hub found [ 1.939111] hub 1-0:1.0: 1 port detected [ 1.943532] orion-ehci f1051000.usb-host: EHCI Host Controller [ 1.949392] orion-ehci f1051000.usb-host: new USB bus registered, assigned bus number 2 [ 1.957575] orion-ehci f1051000.usb-host: irq 26, io mem 0xf1051000 [ 1.973105] orion-ehci f1051000.usb-host: USB 2.0 started, EHCI 1.00 [ 1.980232] hub 2-0:1.0: USB hub found [ 1.984032] hub 2-0:1.0: 1 port detected [ 1.988428] SPEAr-ehci: EHCI SPEAr driver [ 1.992559] ehci-st: EHCI STMicroelectronics driver [ 1.997559] ehci-exynos: EHCI EXYNOS driver [ 2.001859] ehci-atmel: EHCI Atmel driver [ 2.005970] tegra-ehci: Tegra EHCI driver [ 2.010100] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.016282] ohci-pci: OHCI PCI platform driver [ 2.020792] ohci-platform: OHCI generic platform driver [ 2.026130] ohci-omap3: OHCI OMAP3 driver [ 2.030235] SPEAr-ohci: OHCI SPEAr driver [ 2.034348] ohci-st: OHCI STMicroelectronics driver [ 2.039324] ohci-atmel: OHCI Atmel driver [ 2.043820] usbcore: registered new interface driver usb-storage [ 2.050858] ata1: SATA link down (SStatus 0 SControl F300) [ 2.056694] mousedev: PS/2 mouse device common for all mice [ 2.064578] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time- as rtc0 [ 2.074217] i2c /dev entries driver [ 2.080836] i2c i2c-0: Added multiplexed i2c bus 1 [ 2.085973] i2c i2c-0: Added multiplexed i2c bus 2 [ 2.091074] i2c i2c-0: Added multiplexed i2c bus 3 [ 2.098831] orion_wdt: Initial timeout 25 sec [ 2.105111] sdhci: Secure Digital Host Controller Interface driver [ 2.111281] sdhci: Copyright(c) Pierre Ossman [ 2.116870] Synopsys Designware Multimedia Card Interface Driver [ 2.123662] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.129736] sdhci-dove f1092000.sdio-host: No vmmc regulator found [ 2.135910] sdhci-dove f1092000.sdio-host: No vqmmc regulator found [ 2.168095] mmc0: SDHCI controller on f1092000.sdio-host [f1092000.sdio-host] using DMA [ 2.177497] ledtrig-cpu: registered to indicate activity on CPUs [ 2.183747] usbcore: registered new interface driver usbhid [ 2.189308] usbhid: USB HID core driver [ 2.197171] NET: Registered protocol family 10 [ 2.202506] sit: IPv6 over IPv4 tunneling driver [ 2.207900] NET: Registered protocol family 17 [ 2.212360] can: controller area network core (rev 20120528 abi 9) [ 2.218787] NET: Registered protocol family 29 [ 2.223236] can: raw protocol (rev 20120528) [ 2.227494] can: broadcast manager protocol (rev 20120528 t) [ 2.233148] can: netlink gateway (rev 20130117) max_hops=1 [ 2.239027] Key type dns_resolver registered [ 2.243383] ThumbEE CPU extension supported. [ 2.247651] Registering SWP/SWPB emulation handler [ 2.252436] PJ4 iWMMXt v2 coprocessor enabled. [ 2.262521] rtc-mv f10d8500.real-time-clock: setting system clock to 2023-01-09 13:59:40 UTC (1673272780) [ 2.275246] Freeing unused kernel memory: 1048K [ 2.308149] mmc0: new high speed SD card at address 59b4 [ 2.313823] devpts: called with bogus options [ 2.318402] mmcblk0: mmc0:59b4 USD 1.87 GiB [ 2.326533] mmcblk0: p1 Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 2.436954] udevd[87]: starting version 3.2.9 [ 2.442296] random: udevd: uninitialized urandom read (16 bytes read, 7 bits of entropy available) [ 2.451785] random: udevd: uninitialized urandom read (16 bytes read, 7 bits of entropy available) [ 2.460882] random: udevd: uninitialized urandom read (16 bytes read, 7 bits of entropy available) [ 2.479395] udevd[87]: specified user 'tss' unknown [ 2.484506] udevd[87]: specified group 'tss' unknown [ 2.492987] udevd[88]: starting eudev-3.2.9 done Saving random seed: [ 3.880990] random: dd: uninitialized urandom read (512 bytes read, 15 bits of entropy available) OK Starting network: OK Starting dropbear sshd: [ 3.966711] random: dropbear: uninitialized urandom read (32 bytes read, 16 bits of entropy available) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-969018/environment . /lava-969018/environment / # /lava-969018/bin/lava-test-runner /lava-969018/0 /lava-969018/bin/lava-test-runner /lava-969018/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-969018/0/tests/0_dmesg [ 4.527369] + cat uuid + UUID=969018_1.5.2.3.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 4.568496] [ 4.607308] [ 4.646260] + set +x [ 4.655800] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-969018/environment / # . /lava-969018/environment/lava-969018/bin/lava-test-runner /lava-969018/1 / # /lava-969018/bin/lava-test-runner /lava-969018/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-969018/1/tests/1_bootrr[ 5.128454] + cat uuid + UUID=969018_1.5.2.3.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-969018/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-969018/1/../bin/lava-test-case [ 5.159253] /lava-969018/1/../bin/lava-test-case [ 5.195153] /lava-969018/1/../bin/lava-test-case [ 5.218203] + set +x [ 5.235470] / #