[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 8414425/tftp-deploy-odpjwswz/kernel/zImage tftp 0x10000000 8414425/tftp-deploy-odpjwswz/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '8414425/tftp-deploy-odpjwswz/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################################### 12.2 MiB/s done Bytes transferred = 6580176 (6467d0 hex) => tftp 0x14000000 8414425/tftp-deploy-odpjwswz/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 8414425/tftp-deploy-odpjwswz/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '8414425/tftp-deploy-odpjwswz/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################## 5.5 MiB/s done Bytes transferred = 7110972 (6c813c hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 8414425/tftp-deploy-odpjwswz/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 8414425/tftp-deploy-odpjwswz/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '8414425/tftp-deploy-odpjwswz/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.9 MiB/s done Bytes transferred = 36503 (8e97 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/8414425/extract-nfsrootfs-ic9s7qto,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/8414425/extract-nfsrootfs-ic9s7qto,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x6467d0 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 7110908 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0be96 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.302-rt232-st28 (KernelCI@build-j725701-arm-gcc-10-multi-v7-defconfig-r5vnp) (gcc version 10.2.1 20210110 (Debian 10.2.1-6) ) #1 SMP Mon Dec 19 23:02:31 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] PERCPU: Embedded 11 pages/cpu @ef7ad000 s15180 r8192 d21684 u45056 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/8414425/extract-nfsrootfs-ic9s7qto,tcp,hard ip=dhcp [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 951888K/1048576K available (8641K kernel code, 986K rwdata, 3828K rodata, 1044K init, 320K bss, 31152K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0e36668 (12474 kB) [ 0.000000] .init : 0xc0e37000 - 0xc0f3c000 (1044 kB) [ 0.000000] .data : 0xc0f3c000 - 0xc10328a0 ( 987 kB) [ 0.000000] .bss : 0xc1035000 - 0xc10850d8 ( 321 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=4 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C-310 erratum 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000006] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000022] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.002313] Console: colour dummy device 80x30 [ 0.002339] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=15000) [ 0.002351] pid_max: default: 32768 minimum: 301 [ 0.002459] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.002470] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003050] CPU: Testing write buffer coherency: ok [ 0.003076] CPU0: Spectre v2: using BPIALL workaround [ 0.003348] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.003433] Setting up static identity map for 0x10209000 - 0x10209098 [ 0.007458] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.007463] CPU1: Spectre v2: using BPIALL workaround [ 0.008229] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.008233] CPU2: Spectre v2: using BPIALL workaround [ 0.008996] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.009001] CPU3: Spectre v2: using BPIALL workaround [ 0.009076] Brought up 4 CPUs [ 0.009088] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.009096] CPU: All CPU(s) started in SVC mode. [ 0.010044] devtmpfs: initialized [ 0.017966] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.018648] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns [ 0.018677] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.022028] pinctrl core: initialized pinctrl subsystem [ 0.023770] NET: Registered protocol family 16 [ 0.026991] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.039364] cpuidle: using governor ladder [ 0.054355] cpuidle: using governor menu [ 0.054618] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.074959] No ATAGs? [ 0.074996] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.075005] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.077995] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.080608] Serial: AMBA PL011 UART driver [ 0.082794] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 0.109607] mxs-dma 110000.dma-apbh: initialized [ 0.115008] vgaarb: loaded [ 0.115935] SCSI subsystem initialized [ 0.116399] usbcore: registered new interface driver usbfs [ 0.116455] usbcore: registered new interface driver hub [ 0.116498] usbcore: registered new device driver usb [ 0.118307] pps_core: LinuxPPS API ver. 1 registered [ 0.118315] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.118348] PTP clock support registered [ 0.118598] EDAC MC: Ver: 3.0.0 [ 0.120991] clocksource: Switched to clocksource mxc_timer1 [ 0.130800] NET: Registered protocol family 2 [ 0.130940] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.132001] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.132091] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.132231] TCP: Hash tables configured (established 8192 bind 8192) [ 0.132396] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.132438] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.132613] NET: Registered protocol family 1 [ 0.132952] RPC: Registered named UNIX socket transport module. [ 0.132961] RPC: Registered udp transport module. [ 0.132968] RPC: Registered tcp transport module. [ 0.132975] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.133442] Unpacking initramfs... [ 0.638010] Freeing initrd memory: 6948K [ 0.638444] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.650307] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.651116] NFS: Registering the id_resolver key type [ 0.651160] Key type id_resolver registered [ 0.651167] Key type id_legacy registered [ 0.651244] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.652759] bounce: pool size: 64 pages [ 0.652967] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.652990] io scheduler noop registered [ 0.653006] io scheduler deadline registered [ 0.653045] io scheduler cfq registered (default) [ 0.675286] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.675304] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.729458] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.731950] SuperH (H)SCI(F) driver initialized [ 0.732649] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 24, base_baud = 5000000) is a IMX [ 0.733274] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 295, base_baud = 5000000) is a IMX [ 1.434959] console [ttymxc1] enabled [ 1.439577] msm_serial: driver initialized [ 1.444414] STMicroelectronics ASC driver initialized [ 1.451489] [drm] Initialized drm 1.1.0 20060810 [ 1.459594] lcd_panel supply power not found, using dummy regulator [ 1.466091] panel supply power not found, using dummy regulator [ 1.479038] loop: module loaded [ 1.490925] CAN device driver interface [ 1.496680] 2188000.ethernet supply phy not found, using dummy regulator [ 1.511245] pps pps0: new PPS source ptp0 [ 1.532639] fec 2188000.ethernet eth0: registered PHC device 0 [ 1.538928] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 1.545911] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.555094] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.562565] usbcore: registered new interface driver pegasus [ 1.568303] usbcore: registered new interface driver asix [ 1.573770] usbcore: registered new interface driver ax88179_178a [ 1.579927] usbcore: registered new interface driver cdc_ether [ 1.585838] usbcore: registered new interface driver smsc75xx [ 1.591674] usbcore: registered new interface driver smsc95xx [ 1.597482] usbcore: registered new interface driver net1080 [ 1.603203] usbcore: registered new interface driver cdc_subset [ 1.609181] usbcore: registered new interface driver zaurus [ 1.614846] usbcore: registered new interface driver cdc_ncm [ 1.622500] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.629053] ehci-pci: EHCI PCI platform driver [ 1.633561] ehci-platform: EHCI generic platform driver [ 1.639051] ehci-omap: OMAP-EHCI Host Controller driver [ 1.644472] ehci-orion: EHCI orion driver [ 1.648669] SPEAr-ehci: EHCI SPEAr driver [ 1.652868] ehci-st: EHCI STMicroelectronics driver [ 1.657928] ehci-exynos: EHCI EXYNOS driver [ 1.662321] ehci-atmel: EHCI Atmel driver [ 1.666512] tegra-ehci: Tegra EHCI driver [ 1.670718] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.676932] ohci-pci: OHCI PCI platform driver [ 1.681446] ohci-platform: OHCI generic platform driver [ 1.686895] ohci-omap3: OHCI OMAP3 driver [ 1.691096] SPEAr-ohci: OHCI SPEAr driver [ 1.695279] ohci-st: OHCI STMicroelectronics driver [ 1.700342] ohci-atmel: OHCI Atmel driver [ 1.704963] usbcore: registered new interface driver usb-storage [ 1.716015] ci_hdrc ci_hdrc.0: doesn't support gadget [ 1.721103] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 1.726021] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 [ 1.741020] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 1.747222] hub 1-0:1.0: USB hub found [ 1.751041] hub 1-0:1.0: 1 port detected [ 1.755573] 2184200.usb supply vbus not found, using dummy regulator [ 1.765348] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 1.770270] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [ 1.786012] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 1.792156] hub 2-0:1.0: USB hub found [ 1.795941] hub 2-0:1.0: 1 port detected [ 1.800836] mousedev: PS/2 mouse device common for all mice [ 1.810820] i2c /dev entries driver [ 1.824396] sdhci: Secure Digital Host Controller Interface driver [ 1.830597] sdhci: Copyright(c) Pierre Ossman [ 1.836794] Synopsys Designware Multimedia Card Interface Driver [ 1.844130] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.850612] sdhci-esdhc-imx 2198000.usdhc: could not get ultra high speed state, work on normal mode [ 1.859790] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [ 1.864960] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [ 1.870379] sdhci-esdhc-imx 2198000.usdhc: No vqmmc regulator found [ 1.911124] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 1.918802] sdhci-esdhc-imx 219c000.usdhc: could not get ultra high speed state, work on normal mode [ 1.927973] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO [ 1.934307] sdhci-esdhc-imx 219c000.usdhc: No vqmmc regulator found [ 1.964443] mmc0: new high speed SDHC card at address 0001 [ 1.970373] mmcblk0: mmc0:0001 SD 14.6 GiB [ 1.976163] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [ 1.985621] ledtrig-cpu: registered to indicate activity on CPUs [ 1.991880] usbcore: registered new interface driver usbhid [ 1.997472] usbhid: USB HID core driver [ 2.006529] NET: Registered protocol family 10 [ 2.011820] sit: IPv6 over IPv4 tunneling driver [ 2.017112] NET: Registered protocol family 17 [ 2.018426] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 2.018430] GPT:29296874 != 30560255 [ 2.018433] GPT:Alternate GPT header not at the end of the disk. [ 2.018435] GPT:29296874 != 30560255 [ 2.018437] GPT: Use GNU Parted to correct GPT errors. [ 2.018480] mmcblk0: p1 p2 p3 [ 2.050400] can: controller area network core (rev 20120528 abi 9) [ 2.056810] NET: Registered protocol family 29 [ 2.061287] can: raw protocol (rev 20120528) [ 2.065569] can: broadcast manager protocol (rev 20120528 t) [ 2.071263] can: netlink gateway (rev 20130117) max_hops=1 [ 2.076024] usb 2-1: new high-speed USB device number 2 using ci_hdrc [ 2.083668] Key type dns_resolver registered [ 2.088402] ThumbEE CPU extension supported. [ 2.092707] Registering SWP/SWPB emulation handler [ 2.099318] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 2.108832] lcd_panel supply power not found, using dummy regulator [ 2.116143] panel supply power not found, using dummy regulator [ 2.123755] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 2.130434] hctosys: unable to open rtc device (rtc0) [ 2.130590] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 2.133730] lcd_panel supply power not found, using dummy regulator [ 2.134686] panel supply power not found, using dummy regulator [ 2.231624] fec 2188000.ethernet eth0: Freescale FEC PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=-1) [ 2.244413] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 2.251618] hub 2-1:1.0: USB hub found [ 2.255463] hub 2-1:1.0: 3 ports detected [ 2.260866] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 [ 2.270324] lcd_panel supply power not found, using dummy regulator [ 2.277609] panel supply power not found, using dummy regulator [ 6.231476] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 6.239024] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.251060] Sending DHCP requests ., OK [ 6.281015] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 [ 6.289149] IP-Config: Complete: [ 6.292403] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 [ 6.302852] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) [ 6.310697] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 6.317757] nameserver0=192.168.201.1 [ 6.322109] CAN XCVR: disabling [ 6.328156] Freeing unused kernel memory: 1044K Loading, please wait... Starting version 247.3-7+deb11u1 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:09 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.35 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-5 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 8.717621] systemd[1]: System time before build time, advancing clock. [ 8.897397] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 8.921125] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 8.942937] systemd[1]: Set hostname to . [ 9.786865] systemd[1]: Queued start job for default target Graphical Interface. [ 9.795562] random: systemd: uninitialized urandom read (16 bytes read, 120 bits of entropy available) [ 9.805111] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 9.817563] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 9.826675] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 9.846210] random: systemd: uninitialized urandom read (16 bytes read, 121 bits of entropy available) [ 9.856063] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 9.876164] random: systemd: uninitialized urandom read (16 bytes read, 121 bits of entropy available) [ 9.885912] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 9.906174] random: systemd: uninitialized urandom read (16 bytes read, 121 bits of entropy available) [ 9.915810] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 9.936183] random: systemd: uninitialized urandom read (16 bytes read, 121 bits of entropy available) [ 9.945798] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 9.971203] random: systemd: uninitialized urandom read (16 bytes read, 121 bits of entropy available) [ 9.980801] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 10.001343] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 10.013184] random: systemd: uninitialized urandom read (16 bytes read, 121 bits of entropy available) [ 10.022602] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 10.041433] random: systemd: uninitialized urandom read (16 bytes read, 122 bits of entropy available) [ 10.050842] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 10.066227] random: systemd: uninitialized urandom read (16 bytes read, 122 bits of entropy available) [ 10.075635] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 10.091188] random: systemd: uninitialized urandom read (16 bytes read, 122 bits of entropy available) [ 10.100600] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 10.116296] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 10.131752] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 10.171670] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 10.181872] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 10.201897] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 10.222626] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 10.243473] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 10.261745] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 10.281655] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 10.290346] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 10.321410] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 10.336659] systemd[1]: Condition check resulted in Kernel Trace File System being skipped. [ 10.349326] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 10.372008] random: nonblocking pool is initialized [ 10.374528] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 10.399750] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 10.420232] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 10.454964] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 10.487343] systemd[1]: Starting Journal Service... Starting Journal Service... [ 10.510171] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 10.530085] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 10.559260] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 10.584331] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 10.608039] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 10.672864] systemd[1]: modprobe@configfs.service: Succeeded. [ 10.679505] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 10.712426] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ 10.934744] systemd-journald[167]: Received client request to flush runtime journal. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ 12.473298] proc: unrecognized mount option "hidepid=invisible" or missing value [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Found device /dev/ttymxc1. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ 13.098193] proc: unrecognized mount option "hidepid=invisible" or missing value [ 13.107895] proc: unrecognized mount option "hidepid=invisible" or missing value [ OK ] Started Network Time Synchronization. [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Permit User Sessions... [ 15.897944] proc: unrecognized mount option "hidepid=invisible" or missing value [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.4.302-rt232-st28 #1 SMP Mon Dec 19 23:02:31 UTC 2022 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/8414425/extract-nfsrootfs-ic9s7qto' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/8414425/extract-nfsrootfs-ic9s7qto' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-8414425/environment . /lava-8414425/environment / # /lava-8414425/bin/lava-test-runner /lava-8414425/0 /lava-8414425/bin/lava-test-runner /lava-8414425/0 + export TESTRUN_ID=0_dmesg + cd /lava-8414425/0/tests/0_dmesg + cat uuid + UUID=8414425_1.6.2.4.1 + set +x[ 24.801746] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 24.907939] [ 24.976275] [ 25.045845] + set +x [ 25.054992] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-8414425/environment / # . /lava-8414425/environment/lava-8414425/bin/lava-test-runner /lava-8414425/1 / # /lava-8414425/bin/lava-test-runner /lava-8414425/1 + export TESTRUN_ID=1_bootrr + cd /lava-8414425/1/tests/1_bootrr + cat uuid + UUID=8414425_1.6.2.4.5 + set +x[ 25.639961] + export PATH=/opt/bootrr/libexec/[ 25.650114] bootrr/helpers:/lava-8414425/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr /lava-8414425/1/tests/1_bootrr/run.sh: 15: cd: can't cd to /opt/bootrr/libexec/bootrr + set +x / #