Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-rc4-00059-g2b9b9cdd5f-dirty (Mar 29 2019 - 11:33:52 +0000) DRAM: 256 MiB CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2019.04-rc4-00059-g2b9b9cdd5f-dirty (Mar 29 2019 - 11:33:52 +0000) Allwinner Technology CPU: Allwinner A13 (SUN5I) Model: Olimex A13-Olinuxino Micro I2C: ready DRAM: 256 MiB MMC: mmc@1c0f000: 0 Loading Environment from FAT... *** Warning - bad CRC, using default environment Setting up a 1024x768 vga console (overscan 0x0) In: serial Out: vga Err: vga Net: No ethernet found. starting USB... USB0: USB EHCI 1.00 USB1: USB OHCI 1.0 scanning bus 0 for devices... Warning: asix_eth using MAC address from ROM 2 USB Device(s) found scanning bus 1 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 10.201.3.189 (11 ms) => setenv serverip 10.201.1.8 setenv serverip 10.201.1.8 => tftp 0x42000000 3053652/tftp-deploy-gizz2139/kernel/zImage tftp 0x42000000 3053652/tftp-deploy-gizz2139/kernel/zImage Using asix_eth device TFTP from server 10.201.1.8; our IP address is 10.201.3.189 Filename '3053652/tftp-deploy-gizz2139/kernel/zImage'. Load address: 0x42000000 Loading: *################################################################# ################################################################# ################################################################# ###################### 1.1 MiB/s done Bytes transferred = 3184024 (309598 hex) => tftp 0x43300000 3053652/tftp-deploy-gizz2139/ramdisk/ramdisk.cpio.gz.uboot tftp 0x43300000 3053652/tftp-deploy-gizz2139/ramdisk/ramdisk.cpio.gz.uboot Using asix_eth device TFTP from server 10.201.1.8; our IP address is 10.201.3.189 Filename '3053652/tftp-deploy-gizz2139/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x43300000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################### 1.1 MiB/s done Bytes transferred = 7932653 (790aed hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x43000000 3053652/tftp-deploy-gizz2139/dtb/sun5i-a13-olinuxino-micro.dtb tftp 0x43000000 3053652/tftp-deploy-gizz2139/dtb/sun5i-a13-olinuxino-micro.dtb Using asix_eth device TFTP from server 10.201.1.8; our IP address is 10.201.3.189 Filename '3053652/tftp-deploy-gizz2139/dtb/sun5i-a13-olinuxino-micro.dtb'. Load address: 0x43000000 Loading: *## 755.9 KiB/s done Bytes transferred = 17041 (4291 hex) => setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x42000000 0x43300000 0x43000000 bootz 0x42000000 0x43300000 0x43000000 ## Loading init Ramdisk from Legacy Image at 43300000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 7932589 Bytes = 7.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Using Device Tree in place at 43000000, end 43007290 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.302-rt232-st28 (KernelCI@build-j725751-arm-gcc-10-sunxi-defconfig-cd4jf) (gcc version 10.2.1 20210110 (Debian 10.2.1-6) ) #1 SMP Mon Dec 19 22:46:58 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Olimex A13-Olinuxino Micro [ 0.000000] Malformed early option 'earlycon' [ 0.000000] Memory policy: Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] PERCPU: Embedded 11 pages/cpu @cfadf000 s13516 r8192 d23348 u45056 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64262 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 242364K/259072K available (4519K kernel code, 198K rwdata, 1284K rodata, 280K init, 249K bss, 16708K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0000000 - 0xff800000 ( 760 MB) [ 0.000000] lowmem : 0xc0000000 - 0xcfd00000 ( 253 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc05b327c (5805 kB) [ 0.000000] .init : 0xc05b4000 - 0xc05fa000 ( 280 kB) [ 0.000000] .data : 0xc05fa000 - 0xc062b880 ( 199 kB) [ 0.000000] .bss : 0xc062e000 - 0xc066c5dc ( 250 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000021] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000047] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000176] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns [ 0.000370] Console: colour dummy device 80x30 [ 0.000407] Calibrating delay loop... 1001.88 BogoMIPS (lpj=5009408) [ 0.090092] pid_max: default: 32768 minimum: 301 [ 0.090197] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090207] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090836] CPU: Testing write buffer coherency: ok [ 0.090882] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.091185] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.091281] Setting up static identity map for 0x40008280 - 0x400082d8 [ 0.092189] Brought up 1 CPUs [ 0.092202] SMP: Total of 1 processors activated (1001.88 BogoMIPS). [ 0.092209] CPU: All CPU(s) started in SVC mode. [ 0.093563] devtmpfs: initialized [ 0.098396] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.098692] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.098718] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.099040] pinctrl core: initialized pinctrl subsystem [ 0.099954] NET: Registered protocol family 16 [ 0.100641] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.104202] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.110972] reg-fixed-voltage usb1-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe [ 0.112114] SCSI subsystem initialized [ 0.112635] usbcore: registered new interface driver usbfs [ 0.112702] usbcore: registered new interface driver hub [ 0.112748] usbcore: registered new device driver usb [ 0.112889] pps_core: LinuxPPS API ver. 1 registered [ 0.112897] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.112929] PTP clock support registered [ 0.113914] clocksource: Switched to clocksource timer [ 0.114837] simple-framebuffer 4fd00000.framebuffer: framebuffer at 0x4fd00000, 0x300000 bytes, mapped to 0xd0100000 [ 0.114854] simple-framebuffer 4fd00000.framebuffer: format=x8r8g8b8, mode=1024x768x32, linelength=4096 [ 0.127279] Console: switching to colour frame buffer device 128x48 [ 0.138906] simple-framebuffer 4fd00000.framebuffer: fb0: simplefb registered! [ 0.148122] NET: Registered protocol family 2 [ 0.148308] IP idents hash table entries: 4096 (order: 3, 32768 bytes) [ 0.148735] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.148765] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 0.148798] TCP: Hash tables configured (established 2048 bind 2048) [ 0.148874] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.148893] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.149047] NET: Registered protocol family 1 [ 0.149489] RPC: Registered named UNIX socket transport module. [ 0.149502] RPC: Registered udp transport module. [ 0.149508] RPC: Registered tcp transport module. [ 0.149513] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.149767] Unpacking initramfs... [ 0.639685] Freeing initrd memory: 7748K [ 0.651813] NFS: Registering the id_resolver key type [ 0.651886] Key type id_resolver registered [ 0.651892] Key type id_legacy registered [ 0.653230] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 0.653250] io scheduler noop registered [ 0.653261] io scheduler deadline registered [ 0.653291] io scheduler cfq registered (default) [ 0.655262] sun5i-a13-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 0.719493] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.722681] console [ttyS0] disabled [ 0.742796] 1c28400.serial: ttyS0 at MMIO 0x1c28400 (irq = 24, base_baud = 1500000) is a U6_16550A [ 1.318011] console [ttyS0] enabled [ 1.322766] CAN device driver interface [ 1.327029] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.333554] ehci-platform: EHCI generic platform driver [ 1.339015] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.345234] ohci-platform: OHCI generic platform driver [ 1.351294] i2c /dev entries driver [ 1.357058] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 1.365464] sunxi-mmc 1c0f000.mmc: No vqmmc regulator found [ 1.371425] sunxi-mmc 1c0f000.mmc: Got CD GPIO [ 1.414085] sunxi-mmc 1c0f000.mmc: base:0xd00a2000 irq:19 [ 1.420718] usbcore: registered new interface driver usbhid [ 1.426343] usbhid: USB HID core driver [ 1.430920] NET: Registered protocol family 17 [ 1.435421] can: controller area network core (rev 20120528 abi 9) [ 1.441861] NET: Registered protocol family 29 [ 1.446336] can: raw protocol (rev 20120528) [ 1.450609] can: broadcast manager protocol (rev 20120528 t) [ 1.456289] can: netlink gateway (rev 20130117) max_hops=1 [ 1.462061] Key type dns_resolver registered [ 1.467064] Registering SWP/SWPB emulation handler [ 1.474399] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.480003] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.487927] ehci-platform 1c14000.usb: irq 20, io mem 0x01c14000 [ 1.513988] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.520979] hub 1-0:1.0: USB hub found [ 1.524865] hub 1-0:1.0: 1 port detected [ 1.529493] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.536184] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 2 [ 1.544082] ohci-platform 1c14400.usb: irq 21, io mem 0x01c14400 [ 1.557243] mmc0: host does not support reading read-only switch, assuming write-enable [ 1.568908] mmc0: new high speed SD card at address 0007 [ 1.574825] mmcblk0: mmc0:0007 SD02G 1.90 GiB [ 1.581620] mmcblk0: p1 p2 [ 1.608776] hub 2-0:1.0: USB hub found [ 1.612573] hub 2-0:1.0: 1 port detected [ 1.616998] hctosys: unable to open rtc device (rtc0) [ 1.763940] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 13.743941] vcc3v0: disabling [ 13.746922] vcc5v0: disabling [ 13.751153] Freeing unused kernel memory: 280K [ 13.787478] devpts: called with bogus options Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 13.919290] udevd[73]: starting version 3.2.9 [ 13.925217] random: udevd: uninitialized urandom read (16 bytes read, 15 bits of entropy available) [ 13.934830] random: udevd: uninitialized urandom read (16 bytes read, 15 bits of entropy available) [ 13.944390] random: udevd: uninitialized urandom read (16 bytes read, 15 bits of entropy available) [ 13.962249] udevd[73]: specified user 'tss' unknown [ 13.967481] udevd[73]: specified group 'tss' unknown [ 13.976590] udevd[74]: starting eudev-3.2.9 done Saving random seed: [ 15.120584] random: dd: uninitialized urandom read (512 bytes read, 18 bits of entropy available) OK Starting network: OK Starting dropbear sshd: [ 15.226844] random: dropbear: uninitialized urandom read (32 bytes read, 19 bits of entropy available) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-3053652/environment . /lava-3053652/environment / # /lava-3053652/bin/lava-test-runner /lava-3053652/0 /lava-3053652/bin/lava-test-runner /lava-3053652/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-3053652/0/tests/0_dmesg + cat uuid [ 15.921038] + UUID=3053652_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 15.967651] [ 16.011194] [ 16.054991] + set +x [ 16.065263] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-3053652/environment / # . /lava-3053652/environment/lava-3053652/bin/lava-test-runner /lava-3053652/1 / # /lava-3053652/bin/lava-test-runner /lava-3053652/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-3053652/1/tests/1_bootrr + cat uuid [ 16.612914] + UUID=3053652_1.5.2.4.5 + set +x [ 16.620471] + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-3053652/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr /lava-3053652/1/tests/1_bootrr/run.sh: cd: line 15: can't cd to /opt/bootrr/libexec/bootrr: No such file or directory + set +x / #