Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3020 device /dev/ttyimx6sx-sdb-1 [115200 N81] (Debian GNU/Linux) U-Boot 2017.03-imx_v2017.03_4.9.88_2.0.0_ga+gb76bb1b (May 01 2018 - 14:41:44 -0500) CPU: Freescale i.MX6SX rev1.4 996 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 29C Reset cause: POR Model: Freescale i.MX6 SoloX SDB RevB Board Board: MX6SX SABRE SDB DRAM: 1 GiB PMIC: PFUZE100! DEV_ID=0x11 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 *** Warning - bad CRC, using default environment Display: Hannstar-XGA (1024x768) Video: 1024x768x18 In: serial Out: serial Err: serial switch to partitions #0, OK mmc2 is current device Net: Warning: ethernet@02188000 using MAC address from ROM Warning: ethernet@021b4000 using MAC address from ROM eth0: ethernet@02188000, eth1: ethernet@021b4000 [PRIME] Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.200 (1666 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80800000 1078986/tftp-deploy-j6hni3yz/kernel/zImage tftp 0x80800000 1078986/tftp-deploy-j6hni3yz/kernel/zImage Using ethernet@021b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.200; sending through gateway 172.16.1.4 Filename '1078986/tftp-deploy-j6hni3yz/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 10 MiB/s done Bytes transferred = 9675264 (93a200 hex) => tftp 0x86800000 1078986/tftp-deploy-j6hni3yz/ramdisk/ramdisk.cpio.gz.uboot tftp 0x86800000 1078986/tftp-deploy-j6hni3yz/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@021b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.200; sending through gateway 172.16.1.4 Filename '1078986/tftp-deploy-j6hni3yz/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 9.7 MiB/s done Bytes transferred = 16055931 (f4fe7b hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x83000000 1078986/tftp-deploy-j6hni3yz/dtb/imx6sx-sdb.dtb tftp 0x83000000 1078986/tftp-deploy-j6hni3yz/dtb/imx6sx-sdb.dtb Using ethernet@021b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.200; sending through gateway 172.16.1.4 Filename '1078986/tftp-deploy-j6hni3yz/dtb/imx6sx-sdb.dtb'. Load address: 0x83000000 Loading: *### 5.4 MiB/s done Bytes transferred = 39893 (9bd5 hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x80800000 0x86800000 0x83000000 bootz 0x80800000 0x86800000 0x83000000 Kernel image @ 0x80800000 [ 0x000000 - 0x93a200 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16055867 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300cbd4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.145-cip17-rt7 (KernelCI@build-j247982-arm-gcc-10-defconfig-blk4p) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sat Oct 1 18:57:20 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 SoloX SDB RevB Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x02020000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xbc000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 16 pages/cpu s33612 r8192 d23732 u65536 [ 0.000000] pcpu-alloc: s33612 r8192 d23732 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933912K/1048576K available (13312K kernel code, 2323K rwdata, 5344K rodata, 2048K init, 414K bss, 49128K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 256 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76430001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008486] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022299] Console: colour dummy device 80x30 <6>[ 0.024206] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034704] pid_max: default: 32768 minimum: 301 <6>[ 0.039728] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047207] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055873] CPU: Testing write buffer coherency: ok <6>[ 0.060430] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065956] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072365] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.079923] rcu: Hierarchical SRCU implementation. <6>[ 0.086703] EFI services will not be available. <6>[ 0.088826] smp: Bringing up secondary CPUs ... <6>[ 0.093467] smp: Brought up 1 node, 1 CPU <6>[ 0.097793] SMP: Total of 1 processors activated (6.00 BogoMIPS). <6>[ 0.104143] CPU: All CPU(s) started in SVC mode. <6>[ 0.109537] devtmpfs: initialized <6>[ 0.118559] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.123925] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.133868] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.144136] pinctrl core: initialized pinctrl subsystem <6>[ 0.148454] DMI not present or invalid. <6>[ 0.151637] NET: Registered protocol family 16 <6>[ 0.157841] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.165046] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.165169] cpuidle: using governor menu <6>[ 0.359479] vdd3p0: supplied by regulator-dummy <6>[ 0.383787] vddpcie: supplied by regulator-dummy <6>[ 0.804767] No ATAGs? <6>[ 0.804850] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.812799] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.823495] imx6sx-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.833505] Serial: AMBA PL011 UART driver <6>[ 0.866231] mxs-dma 1804000.dma-apbh: initialized <6>[ 0.877941] iommu: Default domain type: Translated <6>[ 0.881608] vgaarb: loaded <5>[ 0.884252] SCSI subsystem initialized <7>[ 0.887509] libata version 3.00 loaded. <6>[ 0.891624] usbcore: registered new interface driver usbfs <6>[ 0.897282] usbcore: registered new interface driver hub <6>[ 0.902773] usbcore: registered new device driver usb <6>[ 0.912932] i2c i2c-0: IMX I2C adapter registered <6>[ 0.915723] i2c i2c-2: IMX I2C adapter registered <6>[ 0.921142] i2c i2c-3: IMX I2C adapter registered <6>[ 0.926675] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.930343] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.939768] PTP clock support registered <6>[ 0.948128] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.992321] NET: Registered protocol family 2 <6>[ 1.994353] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.002893] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.010550] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.018606] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.026071] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.032731] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.039580] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.047056] NET: Registered protocol family 1 <6>[ 2.052288] RPC: Registered named UNIX socket transport module. <6>[ 2.057715] RPC: Registered udp transport module. <6>[ 2.062766] RPC: Registered tcp transport module. <6>[ 2.067689] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.074455] PCI: CLS 0 bytes, default 64 <6>[ 2.079181] Trying to unpack rootfs image as initramfs... <6>[ 3.376081] Freeing initrd memory: 15680K <6>[ 3.378200] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.387589] Initialise system trusted keyrings <6>[ 3.391116] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.403081] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.407127] NFS: Registering the id_resolver key type <5>[ 3.411868] Key type id_resolver registered <5>[ 3.416148] Key type id_legacy registered <6>[ 3.420569] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.427437] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.435203] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.440312] Key type asymmetric registered <5>[ 3.444150] Asymmetric key parser 'x509' registered <6>[ 3.449405] bounce: pool size: 64 pages <6>[ 3.453462] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.461152] io scheduler mq-deadline registered <6>[ 3.465936] io scheduler kyber registered <4>[ 3.497919] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 3.523046] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.530068] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.600867] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.609826] SuperH (H)SCI(F) driver initialized <6>[ 3.612852] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 30, base_baud = 1500000) is a IMX <6>[ 3.620833] printk: console [ttymxc0] enabled <6>[ 3.625309] printk: bootconsole [ec_imx21] disabled <6>[ 3.620833] printk: console [ttymxc0] enabled <6>[ 3.625309] printk: bootconsole [ec_imx21] disabled <6>[ 3.631731] 21f4000.serial: ttymxc4 at MMIO 0x21f4000 (irq = 78, base_baud = 1500000) is a IMX <6>[ 3.633519] msm_serial: driver initialized <6>[ 3.633832] STMicroelectronics ASC driver initialized <6>[ 3.636001] STM32 USART driver initialized <6>[ 3.658173] brd: module loaded <6>[ 3.665737] loop: module loaded <6>[ 3.683905] CAN device driver interface <6>[ 3.685492] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.689548] pps pps0: new PPS source ptp0 <6>[ 3.749414] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.751298] pps pps1: new PPS source ptp1 <6>[ 4.599621] fec 21b4000.ethernet eth1: registered PHC device 1 <6>[ 4.601251] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.601259] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.601328] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.601335] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.608750] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.608809] usbcore: registered new interface driver pegasus <6>[ 4.608870] usbcore: registered new interface driver asix <6>[ 4.608903] usbcore: registered new interface driver ax88179_178a <6>[ 4.608935] usbcore: registered new interface driver cdc_ether <6>[ 4.608977] usbcore: registered new interface driver smsc75xx <6>[ 4.609023] usbcore: registered new interface driver smsc95xx <6>[ 4.609055] usbcore: registered new interface driver net1080 <6>[ 4.609091] usbcore: registered new interface driver cdc_subset <6>[ 4.609121] usbcore: registered new interface driver zaurus <6>[ 4.609190] usbcore: registered new interface driver cdc_ncm <6>[ 4.613545] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.613554] ehci-pci: EHCI PCI platform driver <6>[ 4.613604] ehci-platform: EHCI generic platform driver <6>[ 4.613961] ehci-orion: EHCI orion driver <6>[ 4.614230] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.614458] ehci-st: EHCI STMicroelectronics driver <6>[ 4.614680] ehci-exynos: EHCI Exynos driver <6>[ 4.614896] ehci-atmel: EHCI Atmel driver <6>[ 4.615106] tegra-ehci: Tegra EHCI driver <6>[ 4.615351] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.615381] ohci-pci: OHCI PCI platform driver <6>[ 4.615443] ohci-platform: OHCI generic platform driver <6>[ 4.615767] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.616004] ohci-st: OHCI STMicroelectronics driver <6>[ 4.616247] ohci-atmel: OHCI Atmel driver <6>[ 4.617632] usbcore: registered new interface driver usb-storage <6>[ 4.627818] i2c /dev entries driver <6>[ 4.653225] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.653233] sdhci: Copyright(c) Pierre Ossman <6>[ 4.656574] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.659160] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.667751] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.667787] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.669465] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.669503] sdhci-esdhc-imx 219c000.mmc: Got WP GPIO <6>[ 4.671077] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.672459] usbcore: registered new interface driver usbhid <6>[ 4.672468] usbhid: USB HID core driver <6>[ 4.681077] NET: Registered protocol family 10 <6>[ 4.682309] Segment Routing with IPv6 <6>[ 4.682393] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.682998] NET: Registered protocol family 17 <6>[ 4.683022] can: controller area network core <6>[ 4.683097] NET: Registered protocol family 29 <6>[ 4.683105] can: raw protocol <6>[ 4.683113] can: broadcast manager protocol <6>[ 4.683123] can: netlink gateway - max_hops=1 <5>[ 4.683658] Key type dns_resolver registered <6>[ 4.684780] ThumbEE CPU extension supported. <5>[ 4.684800] Registering SWP/SWPB emulation handler <6>[ 4.685254] printk: console [ttymxc0]: printing thread started <5>[ 4.685288] Loading compiled-in X.509 certificates <4>[ 4.714628] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 4.719785] imx_usb 2184000.usb: No over current polarity defined <6>[ 5.107430] mmc1: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA <6>[ 5.108030] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <4>[ 5.133758] imx_usb 2184200.usb: No over current polarity defined <6>[ 5.135265] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 5.139343] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 5.139385] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 5.169968] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <3>[ 5.170189] mxs_phy 20c9000.usbphy: vbus is not valid <6>[ 5.171405] hub 1-0:1.0: USB hub found <6>[ 5.171550] hub 1-0:1.0: 1 port detected <4>[ 5.184578] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 5.200216] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 5.241495] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 5.254983] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 5.318800] mmc3: new high speed SDHC card at address 0001 <6>[ 5.319571] mmcblk3: mmc3:0001 SD16G 14.5 GiB <6>[ 5.324242] mmcblk3: p1 p2 <4>[ 5.337751] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 5.338713] Qualcomm Atheros AR8031/AR8033 2188000.ethernet-1:01: attached PHY driver [Qualcomm Atheros AR8031/AR8033] (mii_bus:phy_addr=2188000.ethernet-1:01, irq=POLL) <6>[ 5.421427] Qualcomm Atheros AR8031/AR8033 2188000.ethernet-1:02: attached PHY driver [Qualcomm Atheros AR8031/AR8033] (mii_bus:phy_addr=2188000.ethernet-1:02, irq=POLL) <6>[ 8.561183] fec 21b4000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off <6>[ 8.570855] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready <5>[ 8.600892] Sending DHCP requests .., OK <6>[ 10.880825] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.200 <6>[ 10.880841] IP-Config: Complete: <6>[ 10.880844] device=eth1, hwaddr=00:04:9f:06:06:f6, ipaddr=172.16.1.200, mask=255.255.255.0, gw=172.16.1.4 <6>[ 10.880856] host=172.16.1.200, domain=example.org, nis-domain=(none) <6>[ 10.880861] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 10.880867] nameserver0=172.16.1.4 <6>[ 10.935694] Freeing unused kernel memory: 2048K <6>[ 10.961149] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 11.133815] udevd[128]: starting version 3.2.9 <5>[ 11.134965] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 11.135266] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 11.135401] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 11.170999] udevd[128]: specified user 'tss' unknown <27>[ 11.171208] udevd[128]: specified group 'tss' unknown <30>[ 11.180281] udevd[129]: starting eudev-3.2.9 <4>[ 12.882372] etnaviv-gpu 1800000.gpu: deferred probe timeout, ignoring dependency <4>[ 12.882397] etnaviv-gpu: probe of 1800000.gpu failed with error -110 <4>[ 12.896059] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 13.213629] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 13.840675] caam 2100000.crypto: Entropy delay = 12000 <6>[ 14.068140] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 14.295567] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 14.295583] caam 2100000.crypto: device ID = 0x0a16010000000200 (Era 4) <6>[ 14.295593] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 14.341556] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 15.160992] spi-nor spi5.0: n25q256a (32768 Kbytes) <4>[ 15.211854] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 15.212655] spi-nor spi5.2: n25q256a (32768 Kbytes) <4>[ 15.292507] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 15.691049] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 15.691265] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 15.703873] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 15.822496] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 16.838691] caam algorithms registered in /proc/crypto <6>[ 16.840301] caam 2100000.crypto: registering rng-caam <4>[ 16.886015] pwm-backlight backlight-display: supply power not found, using dummy regulator done Saving random seed: OK <5>[ 16.940779] random: dd: uninitialized urandom read (32 bytes read) Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK <5>[ 17.038980] random: dropbear: uninitialized urandom read (32 bytes read) /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh expo<5>[ 17.522724] random: crng init done rt SHELL=/bin/sh / # . /lava-1078986/environment . /lava-1078986/environment / # /lava-1078986/bin/lava-test-runner /lava-1078986/0 /lava-1078986/bin/lava-test-runner /lava-1078986/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1078986/0/tests/0_dmesg + cat uuid + UUID=1078986_1.5.2.4.1 + set<8>[ 22.877724] +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 22.928961] <8>[ 22.974510] + set +x / # <8>[ 23.020549] <8>[ 23.022009] # / # export SHELL=/bin/sh. /lava-1078986/environment / # . /lava-1078986/environment //lava-1078986/bin/lava-test-runner /lava-1078986/1 # /lava-1078986/bin/lava-test-runner /lava-1078986/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1078986/1/tests/1_bootrr + cat uuid + UUID=1078986_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-1078986/1/../bin<8>[ 28.772541] :/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-1078986/1/../bin/lava-test-case <8>[ 29.821627] /lava-1078986/1/../bin/lava-test-case <8>[ 29.864301] /lava-1078986/1/../bin/lava-test-case <8>[ 29.891100] + set +x