Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.3 (4 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 752728/tftp-deploy-llb_jdu1/kernel/zImage tftp 0x82000000 752728/tftp-deploy-llb_jdu1/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.3 Filename '752728/tftp-deploy-llb_jdu1/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################### 5.1 MiB/s done Bytes transferred = 9810432 (95b200 hex) => tftp 0x83000000 752728/tftp-deploy-llb_jdu1/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 752728/tftp-deploy-llb_jdu1/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.3 Filename '752728/tftp-deploy-llb_jdu1/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################################### 5.1 MiB/s done Bytes transferred = 16121317 (f5fde5 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 752728/tftp-deploy-llb_jdu1/dtb/am335x-boneblack.dtb tftp 0x88000000 752728/tftp-deploy-llb_jdu1/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.3 Filename '752728/tftp-deploy-llb_jdu1/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.6 MiB/s done Bytes transferred = 62852 (f584 hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2022-10-01 19:21:48 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16121253 Bytes = 15.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 88012583 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.145-cip17-rt7 (KernelCI@build-j247911-arm-gcc-10-multi-v7-defconfig-preempt-rt-npbc9) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT_RT Sat Oct 1 19:00:15 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] On node 0 totalpages: 130560 [ 0.000000] DMA zone: 1020 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 130560 pages, LIFO batch:31 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 16 pages/cpu s34912 r8192 d22432 u65536 [ 0.000000] pcpu-alloc: s34912 r8192 d22432 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129540 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 410704K/522240K available (14336K kernel code, 2354K rwdata, 5368K rodata, 2048K init, 421K bss, 46000K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms. <6>[ 0.000000] rcu: RCU_SOFTIRQ processing moved to rcuc kthreads. <6>[ 0.000000] No expedited grace period (rcu_normal_after_boot). <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008330] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.019074] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.033193] Console: colour dummy device 80x30 <3>[ 0.038062] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.045114] This ensures that you still see kernel messages. Please <3>[ 0.051834] update your kernel commandline. <6>[ 0.056445] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.096070] pid_max: default: 32768 minimum: 301 <6>[ 0.101281] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.109078] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.118237] CPU: Testing write buffer coherency: ok <6>[ 0.123647] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.129504] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.136047] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.145311] rcu: Hierarchical SRCU implementation. <6>[ 0.155801] EFI services will not be available. <6>[ 0.161079] smp: Bringing up secondary CPUs ... <6>[ 0.166012] smp: Brought up 1 node, 1 CPU <6>[ 0.170439] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.177154] CPU: All CPU(s) started in SVC mode. <6>[ 0.182869] devtmpfs: initialized <6>[ 0.201548] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.210125] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.220566] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.231867] pinctrl core: initialized pinctrl subsystem <6>[ 0.240607] DMI not present or invalid. <6>[ 0.245673] NET: Registered protocol family 16 <6>[ 0.254722] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.284134] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.292816] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.293247] cpuidle: using governor menu <6>[ 1.554027] No ATAGs? <6>[ 1.556658] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.574027] Serial: AMBA PL011 UART driver <6>[ 1.622291] iommu: Default domain type: Translated <6>[ 1.628038] vgaarb: loaded <5>[ 1.632648] SCSI subsystem initialized <7>[ 1.637185] libata version 3.00 loaded. <6>[ 1.642092] usbcore: registered new interface driver usbfs <6>[ 1.648064] usbcore: registered new interface driver hub <6>[ 1.653985] usbcore: registered new device driver usb <6>[ 1.661682] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.667065] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.676815] PTP clock support registered <6>[ 1.685644] clocksource: Switched to clocksource dmtimer <6>[ 2.680072] NET: Registered protocol family 2 <6>[ 2.685157] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.694329] tcp_listen_portaddr_hash hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.703405] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.711722] TCP bind hash table entries: 4096 (order: 4, 114688 bytes, linear) <6>[ 2.719606] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.726666] UDP hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 2.733770] UDP-Lite hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 2.741624] NET: Registered protocol family 1 <6>[ 2.747230] RPC: Registered named UNIX socket transport module. <6>[ 2.753595] RPC: Registered udp transport module. <6>[ 2.758804] RPC: Registered tcp transport module. <6>[ 2.763911] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.770834] PCI: CLS 0 bytes, default 64 <6>[ 2.776006] Trying to unpack rootfs image as initramfs... <6>[ 3.968588] Freeing initrd memory: 15744K <6>[ 3.973897] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.984672] Initialise system trusted keyrings <6>[ 3.990003] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 4.006942] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 4.014546] NFS: Registering the id_resolver key type <5>[ 4.020210] Key type id_resolver registered <5>[ 4.024785] Key type id_legacy registered <6>[ 4.029355] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 4.036549] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 4.044469] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 4.049958] Key type asymmetric registered <5>[ 4.054452] Asymmetric key parser 'x509' registered <6>[ 4.059855] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 4.067759] io scheduler mq-deadline registered <6>[ 4.072683] io scheduler kyber registered <3>[ 4.254017] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.262731] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 4.403617] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 4.456330] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 4.547150] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.555921] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 4.633301] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.642004] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 4.662751] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.671575] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 4.754638] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 4.763273] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 4.817751] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 4.946591] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 4.959896] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 4.969614] printk: console [ttyS0] enabled <6>[ 4.969614] printk: console [ttyS0] enabled <6>[ 4.978749] printk: bootconsole [omap8250] disabled <6>[ 4.978749] printk: bootconsole [omap8250] disabled <6>[ 4.993238] SuperH (H)SCI(F) driver initialized <6>[ 5.000843] msm_serial: driver initialized <6>[ 5.005876] STMicroelectronics ASC driver initialized <6>[ 5.014450] STM32 USART driver initialized <6>[ 5.022505] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 5.029359] random: crng init done <6>[ 5.061252] brd: module loaded <6>[ 5.077132] loop: module loaded <6>[ 5.107077] CAN device driver interface <6>[ 5.113330] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 5.121954] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 5.127270] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 5.133595] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 5.139311] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 5.215690] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 5.254020] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 5.264392] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 5.271199] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 5.276949] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 5.287141] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 5.294964] usbcore: registered new interface driver pegasus <6>[ 5.301600] usbcore: registered new interface driver asix <6>[ 5.307487] usbcore: registered new interface driver ax88179_178a <6>[ 5.313921] usbcore: registered new interface driver cdc_ether <6>[ 5.320147] usbcore: registered new interface driver smsc75xx <6>[ 5.326301] usbcore: registered new interface driver smsc95xx <6>[ 5.332385] usbcore: registered new interface driver net1080 <6>[ 5.338397] usbcore: registered new interface driver cdc_subset <6>[ 5.344642] usbcore: registered new interface driver zaurus <6>[ 5.350630] usbcore: registered new interface driver cdc_ncm <6>[ 5.362818] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 5.369743] ehci-pci: EHCI PCI platform driver <6>[ 5.374539] ehci-platform: EHCI generic platform driver <6>[ 5.380875] ehci-orion: EHCI orion driver <6>[ 5.385608] SPEAr-ehci: EHCI SPEAr driver <6>[ 5.390356] ehci-st: EHCI STMicroelectronics driver <6>[ 5.395945] ehci-exynos: EHCI Exynos driver <6>[ 5.400767] ehci-atmel: EHCI Atmel driver <6>[ 5.405391] tegra-ehci: Tegra EHCI driver <6>[ 5.410110] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 5.416675] ohci-pci: OHCI PCI platform driver <6>[ 5.421498] ohci-platform: OHCI generic platform driver <6>[ 5.427573] SPEAr-ohci: OHCI SPEAr driver <6>[ 5.432255] ohci-st: OHCI STMicroelectronics driver <6>[ 5.437948] ohci-atmel: OHCI Atmel driver <6>[ 5.444060] usbcore: registered new interface driver usb-storage <6>[ 5.463256] i2c /dev entries driver <5>[ 5.499505] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 5.508110] sdhci: Secure Digital Host Controller Interface driver <6>[ 5.514596] sdhci: Copyright(c) Pierre Ossman <6>[ 5.523909] Synopsys Designware Multimedia Card Interface Driver <6>[ 5.533662] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 5.547274] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 5.568324] usbcore: registered new interface driver usbhid <6>[ 5.574214] usbhid: USB HID core driver <6>[ 5.606117] NET: Registered protocol family 10 <6>[ 5.615975] Segment Routing with IPv6 <6>[ 5.620028] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 5.627155] NET: Registered protocol family 17 <6>[ 5.632260] can: controller area network core <6>[ 5.637128] NET: Registered protocol family 29 <6>[ 5.641864] can: raw protocol <6>[ 5.645160] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <6>[ 5.653375] can: broadcast manager protocol <6>[ 5.658099] can: netlink gateway - max_hops=1 <5>[ 5.664623] Key type dns_resolver registered <6>[ 5.669531] ThumbEE CPU extension supported. <5>[ 5.674199] Registering SWP/SWPB emulation handler <3>[ 5.680019] omap_voltage_late_init: Voltage driver support not added <6>[ 5.689731] printk: console [ttyS0]: printing thread started <5>[ 5.689794] Loading compiled-in X.509 certificates <6>[ 5.729176] OMAP GPIO hardware version 0.1 <6>[ 5.744897] mmc1: new high speed MMC card at address 0001 <6>[ 5.751757] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 5.752139] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 5.752494] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 5.752772] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (235:0) <6>[ 5.754897] mmcblk1: p1 <4>[ 5.758896] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 5.768631] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 5.796149] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <4>[ 5.796966] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 5.797728] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 5.798597] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <4>[ 5.809300] at24 2-0054: supply vcc not found, using dummy regulator <4>[ 5.853533] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 5.878812] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 5.908463] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 5.938097] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 5.965102] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 5.965134] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 5.965351] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 6.043041] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 6.079944] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 6.157948] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 11.396908] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 11.425772] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 11.456057] Sending DHCP requests ., OK <6>[ 11.496376] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.3 <6>[ 11.496433] IP-Config: Complete: <6>[ 11.496444] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.3, mask=255.255.255.0, gw=192.168.11.1 <6>[ 11.496483] host=192.168.11.3, domain=usen.ad.jp, nis-domain=(none) <6>[ 11.496500] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 11.496521] nameserver0=192.168.11.1 <6>[ 11.519195] Freeing unused kernel memory: 2048K <6>[ 11.527242] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 11.806785] udevd[108]: starting version 3.2.9 <27>[ 11.824282] udevd[108]: specified user 'tss' unknown <27>[ 11.824518] udevd[108]: specified group 'tss' unknown <30>[ 11.841435] udevd[109]: starting eudev-3.2.9 <4>[ 13.911371] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 13.911780] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 13.987156] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 13.987569] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 14.116576] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 14.116633] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 14.117929] hub 1-0:1.0: USB hub found <6>[ 14.165805] hub 1-0:1.0: 1 port detected done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-752728/environment . /lava-752728/environment / # /lava-752728/bin/lava-test-runner /lava-752728/0 /lava-752728/bin/lava-test-runner /lava-752728/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-752728/0/tests/0_dmesg + cat uuid + UUID=752728_1.5.2.4.1 <8>[ 19.715201] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 19.779437] <8>[ 19.838928] + set +x / # # export SHELL=/bin/sh <8>[ 19.898047] <8>[ 19.900343] # / # export SHELL=/bin/sh. /lava-752728/environment / # . /lava-752728/environment/lava-752728/bin/lava-test-runner /lava-752728/1 / # /lava-752728/bin/lava-test-runner /lava-752728/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-752728/1/tests/1_bootrr + cat uuid + UUID=752728_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-752728/1/../b<8>[ 20.420342] in:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-752728/1/../bin/lava-test-case <8>[ 21.506303] /lava-752728/1/../bin/lava-test-case <8>[ 21.562694] /lava-752728/1/../bin/lava-test-case <8>[ 21.596734] + set +x <8>[ 21.625514] / #