Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.78 (1633 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 177722/tftp-deploy-n4cgpswo/kernel/Image tftp 0x82000000 177722/tftp-deploy-n4cgpswo/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.78; sending through gateway 172.16.0.254 Filename '177722/tftp-deploy-n4cgpswo/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################# 12.3 MiB/s done Bytes transferred = 31910400 (1e6ea00 hex) => tftp 0x90080000 177722/tftp-deploy-n4cgpswo/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 177722/tftp-deploy-n4cgpswo/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.78; sending through gateway 172.16.0.254 Filename '177722/tftp-deploy-n4cgpswo/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #### 12.3 MiB/s done Bytes transferred = 15324551 (e9d587 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 177722/tftp-deploy-n4cgpswo/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 177722/tftp-deploy-n4cgpswo/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.78; sending through gateway 172.16.0.254 Filename '177722/tftp-deploy-n4cgpswo/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 4.8 MiB/s done Bytes transferred = 25279 (62bf hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/nfs rw nfsroot=10.228.65.1:/var/lib/lava/dispatcher/tmp/177722/extract-nfsrootfs-kwubdn1o,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/nfs rw nfsroot=10.228.65.1:/var/lib/lava/dispatcher/tmp/177722/extract-nfsrootfs-kwubdn1o,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2022-10-01 19:29:13 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 15324487 Bytes = 14.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 00000000900092be WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.10.145-cip17-rt7 (KernelCI@build-j247870-arm64-gcc-10-defconfig-95jz6) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Sat Oct 1 19:12:27 UTC 2022 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7feb00-0x20ff800fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0 totalpages: 1031680 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 507392 pages, LIFO batch:63 [ 0.000000] Normal zone: 8192 pages used for memmap [ 0.000000] Normal zone: 524288 pages, LIFO batch:63 [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 19 pages/cpu s40344 r8192 d29288 u77824 [ 0.000000] pcpu-alloc: s40344 r8192 d29288 u77824 alloc=19*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/nfs rw nfsroot=10.228.65.1:/var/lib/lava/dispatcher/tmp/177722/extract-nfsrootfs-kwubdn1o,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3901228K/4126720K available (14592K kernel code, 2874K rwdata, 7608K rodata, 5952K init, 502K bss, 192724K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] GICv3: Distributor has no Range Selector support <6>[ 0.000000] GICv3: 16 PPIs implemented <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008682] Console: colour dummy device 80x25 <6>[ 0.013471] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024188] pid_max: default: 32768 minimum: 301 <6>[ 0.029148] LSM: Security Framework initializing <6>[ 0.034113] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.041869] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.050939] rcu: Hierarchical SRCU implementation. <6>[ 0.056186] Platform MSI: gic-its@6020000 domain created <6>[ 0.061886] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.069750] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.075785] EFI services will not be available. <6>[ 0.080725] smp: Bringing up secondary CPUs ... <6>[ 0.085828] Detected PIPT I-cache on CPU1 <6>[ 0.090150] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.097356] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.104930] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.111839] smp: Brought up 1 node, 2 CPUs <6>[ 0.116248] SMP: Total of 2 processors activated. <6>[ 0.121261] CPU features: detected: 32-bit EL0 Support <6>[ 0.126718] CPU features: detected: CRC32 instructions <6>[ 0.132170] CPU features: detected: 32-bit EL1 Support <6>[ 0.148633] CPU: All CPU(s) started at EL2 <6>[ 0.153051] alternatives: patching kernel code <6>[ 0.158544] devtmpfs: initialized <4>[ 0.164218] KASLR disabled due to lack of seed <6>[ 0.169074] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.179183] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.186861] pinctrl core: initialized pinctrl subsystem <6>[ 0.192996] DMI not present or invalid. <6>[ 0.197519] NET: Registered protocol family 16 <6>[ 0.203038] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.210534] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.218780] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.227057] audit: initializing netlink subsys (disabled) <5>[ 0.232890] audit: type=2000 audit(0.156:1): state=initialized audit_enabled=0 res=1 <6>[ 0.233385] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.233388] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.240981] cpuidle: using governor menu <6>[ 0.258479] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.265619] ASID allocator initialised with 65536 entries <6>[ 0.271966] Serial: AMBA PL011 UART driver <6>[ 0.286893] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.294544] SoC family: QorIQ LS1028A <6>[ 0.298496] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.310744] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.317788] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.324818] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.331849] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.339645] cryptd: max_cpu_qlen set to 1000 <6>[ 0.345650] ACPI: Interpreter disabled. <6>[ 0.350698] iommu: Default domain type: Translated <6>[ 0.356117] vgaarb: loaded <5>[ 0.359253] SCSI subsystem initialized <7>[ 0.363394] libata version 3.00 loaded. <6>[ 0.367632] usbcore: registered new interface driver usbfs <6>[ 0.373560] usbcore: registered new interface driver hub <6>[ 0.379203] usbcore: registered new device driver usb <6>[ 0.384811] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.392753] i2c i2c-0: IMX I2C adapter registered <6>[ 0.397938] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.405622] i2c i2c-1: IMX I2C adapter registered <6>[ 0.410722] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.418502] i2c i2c-2: IMX I2C adapter registered <6>[ 0.423772] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.429054] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.438546] PTP clock support registered <6>[ 0.442826] EDAC MC: Ver: 3.0.0 <6>[ 0.446951] FPGA manager framework <6>[ 0.450687] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.457512] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.464031] VFS: Disk quotas dquot_6.6.0 <6>[ 0.468281] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.475575] pnp: PnP ACPI: disabled <6>[ 0.482632] NET: Registered protocol family 2 <6>[ 0.487587] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.496647] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.505572] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.513921] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) <6>[ 0.521923] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.528896] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.535950] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.543508] NET: Registered protocol family 1 <6>[ 0.548489] RPC: Registered named UNIX socket transport module. <6>[ 0.554735] RPC: Registered udp transport module. <6>[ 0.559744] RPC: Registered tcp transport module. <6>[ 0.564754] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.571521] PCI: CLS 0 bytes, default 64 <6>[ 0.575831] Unpacking initramfs... <6>[ 1.083375] Freeing initrd memory: 14960K <6>[ 1.088014] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 1.096699] kvm [1]: IPA Size Limit: 44 bits <6>[ 1.101894] kvm [1]: GICv3: no GICV resource entry <6>[ 1.106997] kvm [1]: disabling GICv2 emulation <6>[ 1.111758] kvm [1]: GIC system register CPU interface enabled <6>[ 1.117947] kvm [1]: vgic interrupt IRQ9 <6>[ 1.122231] kvm [1]: Hyp mode initialized successfully <5>[ 1.128644] Initialise system trusted keyrings <6>[ 1.133495] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.143394] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.150003] NFS: Registering the id_resolver key type <5>[ 1.155384] Key type id_resolver registered <5>[ 1.159873] Key type id_legacy registered <6>[ 1.164227] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.171261] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.179092] 9p: Installing v9fs 9p2000 file system support <5>[ 1.214752] Key type asymmetric registered <5>[ 1.219154] Asymmetric key parser 'x509' registered <6>[ 1.224363] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.232096] io scheduler mq-deadline registered <6>[ 1.236936] io scheduler kyber registered <6>[ 1.245917] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 1.254033] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x0000000000 <6>[ 1.263183] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x0000000000 <6>[ 1.272330] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x0000000000 <6>[ 1.281478] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x0000000000 <6>[ 1.290624] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x0000000000 <6>[ 1.299773] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x0000000000 <6>[ 1.308915] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x0000000000 <6>[ 1.318100] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 1.327219] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 1.334514] pci_bus 0000:00: root bus resource [bus 00] <6>[ 1.340054] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] (bus address [0x00000000-0x0015ffff]) <6>[ 1.350769] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] (bus address [0x00000000-0x0006ffff]) <6>[ 1.361927] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] (bus address [0x00000000-0x0001ffff]) <6>[ 1.372644] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 1.383798] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] (bus address [0x00000000-0x0001ffff]) <6>[ 1.394514] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 1.405668] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] (bus address [0x00000000-0x003fffff]) <6>[ 1.416399] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 1.422760] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.433569] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.444814] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.455882] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.467401] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 1.473209] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.483490] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.494361] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 1.500713] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.511519] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.522762] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.533830] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.545353] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.551160] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.561438] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.572278] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 1.578632] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.589438] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.600692] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.606612] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 1.612966] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.623772] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.635025] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.640931] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 1.647284] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.658090] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.669346] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.675264] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 1.681615] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.692420] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.703662] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.714477] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.720390] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 1.726743] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.737549] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.748803] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.755336] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 1.761701] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.769662] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <3>[ 1.777676] pcieport 0000:00:1f.0: of_irq_parse_pci: failed with rc=-22 <6>[ 1.785017] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.792700] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.801585] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.810557] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 1.817590] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 1.823392] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 1.829896] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 1.840803] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 1.847184] pci 0001:00:00.0: supports D1 D2 <6>[ 1.851760] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 1.859391] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 1.866344] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 1.871768] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 1.879433] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 1.888315] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 1.897272] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 1.904304] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 1.910110] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 1.919422] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 1.930346] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 1.936728] pci 0002:00:00.0: supports D1 D2 <6>[ 1.941301] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 1.948911] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 1.955860] pci 0002:00:00.0: PCI bridge to [bus 01] <4>[ 1.961850] EINJ: ACPI disabled. <6>[ 1.972710] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.980585] printk: console [ttyS0] disabled <6>[ 1.985210] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 1.994414] printk: console [ttyS0] enabled <6>[ 1.994414] printk: console [ttyS0] enabled <6>[ 2.003363] printk: bootconsole [ns16550a0] disabled <6>[ 2.003363] printk: bootconsole [ns16550a0] disabled <6>[ 2.014194] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 2.023558] SuperH (H)SCI(F) driver initialized <6>[ 2.028641] msm_serial: driver initialized <6>[ 2.033358] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 24, base_baud = 12500000) is a FSL_LPUART <5>[ 2.043873] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 2.050616] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 2.055512] arm-smmu 5000000.iommu: stage 1 translation <5>[ 2.061104] arm-smmu 5000000.iommu: stage 2 translation <5>[ 2.066695] arm-smmu 5000000.iommu: nested translation <5>[ 2.072200] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 2.079625] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 2.086446] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 2.093174] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 2.099900] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <6>[ 2.111050] loop: module loaded <6>[ 2.119425] megasas: 07.714.04.00-rc1 <6>[ 2.125402] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 2.136996] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 2.146083] 8 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 2.153172] Creating 8 MTD partitions on \"20c0000.spi\": <5>[ 2.158682] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 2.165880] 0x000000010000-0x000000100000 : \"failsafe bootloader\" <5>[ 2.173843] 0x000000100000-0x000000140000 : \"failsafe DP firmware\" <5>[ 2.181844] 0x000000140000-0x0000001e0000 : \"failsafe trusted firmware\" <5>[ 2.189853] 0x0000001e0000-0x000000200000 : \"reserved\" <5>[ 2.197838] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 2.205846] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 2.213839] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 2.223504] tun: Universal TUN/TAP device driver, 1.6 <6>[ 2.229280] thunder_xcv, ver 1.0 <6>[ 2.232808] thunder_bgx, ver 1.0 <6>[ 2.236336] nicpf, ver 1.0 <6>[ 2.239805] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 2.353529] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 2.360046] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 7e:95:ed:7a:66:a2 <6>[ 2.368874] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using 6a:61:23:6d:f5:ca <6>[ 2.384288] fsl_enetc 0000:00:00.1: Adding to iommu group 1 <6>[ 2.497524] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 2.504921] fsl_enetc 0000:00:00.1: device is disabled, skipping <6>[ 2.511294] fsl_enetc 0000:00:00.2: Adding to iommu group 2 <6>[ 2.621526] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 2.628333] fsl_enetc 0000:00:00.2: device is disabled, skipping <6>[ 2.634696] fsl_enetc 0000:00:00.6: Adding to iommu group 3 <6>[ 2.745525] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 2.752331] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 2.758753] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 4 <6>[ 2.869525] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 2.876706] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 5 <6>[ 2.882993] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 2.889912] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 2.898920] pps pps0: new PPS source ptp0 <6>[ 2.903641] hclge is initializing <6>[ 2.907245] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 2.914759] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 2.920380] e1000: Intel(R) PRO/1000 Network Driver <6>[ 2.925537] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 2.931599] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.936843] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.943068] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.948748] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.954647] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 2.961200] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 2.967591] sky2: driver version 1.30 <6>[ 2.972132] VFIO - User Level meta-driver version: 0.3 <6>[ 2.977891] dwc3 3100000.usb: Adding to iommu group 6 <6>[ 2.983788] dwc3 3110000.usb: Adding to iommu group 7 <6>[ 2.990422] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.997253] ehci-pci: EHCI PCI platform driver <6>[ 3.001992] ehci-platform: EHCI generic platform driver <6>[ 3.007573] ehci-orion: EHCI orion driver <6>[ 3.011912] ehci-exynos: EHCI Exynos driver <6>[ 3.016420] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.022894] ohci-pci: OHCI PCI platform driver <6>[ 3.027634] ohci-platform: OHCI generic platform driver <6>[ 3.033199] ohci-exynos: OHCI Exynos driver <6>[ 3.037910] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.043693] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 3.051780] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000002002010010 <6>[ 3.061502] xhci-hcd xhci-hcd.0.auto: irq 28, io mem 0x03100000 <6>[ 3.068112] hub 1-0:1.0: USB hub found <6>[ 3.072152] hub 1-0:1.0: 1 port detected <6>[ 3.076500] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.082276] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 3.090227] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.097067] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.105699] hub 2-0:1.0: USB hub found <6>[ 3.109737] hub 2-0:1.0: 1 port detected <6>[ 3.114137] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 3.119915] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 3.128000] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000002002010010 <6>[ 3.137715] xhci-hcd xhci-hcd.1.auto: irq 29, io mem 0x03110000 <6>[ 3.144248] hub 3-0:1.0: USB hub found <6>[ 3.148287] hub 3-0:1.0: 1 port detected <6>[ 3.152629] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 3.158404] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 3.166360] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.173199] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.181824] hub 4-0:1.0: USB hub found <6>[ 3.185862] hub 4-0:1.0: 1 port detected <6>[ 3.190397] usbcore: registered new interface driver usb-storage <6>[ 3.198194] i2c /dev entries driver <6>[ 3.204655] sp805-wdt c000000.watchdog: registration successful <6>[ 3.210959] sp805-wdt c010000.watchdog: registration successful <6>[ 3.218347] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 3.227145] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.233656] sdhci: Copyright(c) Pierre Ossman <6>[ 3.238597] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.245500] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.251913] sdhci-esdhc 2140000.mmc: Adding to iommu group 8 <6>[ 3.252471] sdhci-esdhc 2150000.mmc: Adding to iommu group 9 <6>[ 3.257875] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.271001] usbcore: registered new interface driver usbhid <6>[ 3.276868] usbhid: USB HID core driver <6>[ 3.283620] NET: Registered protocol family 17 <6>[ 3.288447] 9pnet: Installing 9P2000 support <6>[ 3.289534] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <5>[ 3.293042] Key type dns_resolver registered <6>[ 3.300167] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 3.300167] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 3.304938] printk: console [ttyS0]: printing thread started <6>[ 3.304978] registered taskstats version 1 <5>[ 3.304983] Loading compiled-in X.509 certificates <6>[ 3.307235] fsl-edma 22c0000.dma-controller: Adding to iommu group 10 <6>[ 3.308314] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 3.308476] pcieport 0001:00:00.0: PME: Signaling with IRQ 31 <6>[ 3.308610] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 3.308749] pcieport 0002:00:00.0: PME: Signaling with IRQ 33 <6>[ 3.321164] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 3.386996] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.0:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 3.390047] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 3.417522] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 3.419581] mmc0: new HS400 MMC card at address 0001 <6>[ 3.420025] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 3.420221] mmcblk0boot0: mmc0:0001 S0J56X partition 1 31.5 MiB <6>[ 3.420448] mmcblk0boot1: mmc0:0001 S0J56X partition 2 31.5 MiB <6>[ 3.420564] mmcblk0rpmb: mmc0:0001 S0J56X partition 3 4.00 MiB, chardev (234:0) <6>[ 3.428403] mmcblk0: p1 p2 <6>[ 3.621588] hub 3-1:1.0: USB hub found <6>[ 3.621724] hub 3-1:1.0: 7 ports detected <6>[ 6.470449] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 6.493529] Sending DHCP requests ., OK <6>[ 6.513556] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.78 <6>[ 6.513568] IP-Config: Complete: <6>[ 6.513570] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.78, mask=255.255.255.0, gw=172.16.0.254 <6>[ 6.513582] host=172.16.0.78, domain=lava.lan, nis-domain=(none) <6>[ 6.513587] bootserver=0.0.0.0, rootserver=10.228.65.1, rootpath= <6>[ 6.513594] nameserver0=8.8.8.8 <6>[ 6.513861] ALSA device list: <6>[ 6.513870] No soundcards found. <6>[ 6.517443] Freeing unused kernel memory: 5952K <6>[ 6.577638] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 <6>[ 6.941070] mali-dp f080000.display: Adding to iommu group 13 <6>[ 6.969048] NET: Registered protocol family 10 <6>[ 6.969694] Segment Routing with IPv6 <4>[ 6.983821] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 6.984006] mscc_felix 0000:00:00.5: Adding to iommu group 14 <6>[ 6.984150] mscc_felix 0000:00:00.5: device is disabled, skipping <4>[ 6.994948] wm8904 2-001a: supply DCVDD not found, using dummy regulator <4>[ 6.995037] wm8904 2-001a: supply DBVDD not found, using dummy regulator <4>[ 6.995061] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 6.995091] wm8904 2-001a: supply CPVDD not found, using dummy regulator <4>[ 6.995116] wm8904 2-001a: supply MICVDD not found, using dummy regulator <6>[ 7.027207] wm8904 2-001a: revision A <6>[ 7.035133] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 7.035976] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 7.037452] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 7.038299] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 7.054490] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 7.069957] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 7.069974] rtc-rv8803 0-0032: Voltage low, data loss detected. <4>[ 7.080500] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 7.080625] rtc-rv8803 0-0032: registered as rtc0 <4>[ 7.123434] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 7.123443] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 7.126469] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 7.168476] caam 8000000.crypto: Entropy delay = 3200 <6>[ 7.239674] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 7.239693] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 7.239699] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 7.239705] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 7.283300] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 7.292587] caam algorithms registered in /proc/crypto <6>[ 7.293949] caam 8000000.crypto: registering rng-caam <6>[ 7.294175] caam_jr 8020000.jr: Adding to iommu group 16 <6>[ 7.294710] caam_jr 8030000.jr: Adding to iommu group 17 <6>[ 7.295196] caam_jr 8040000.jr: Adding to iommu group 18 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... done. <5>[ 7.354235] random: crng init done IP-Config: eth0 hardware address 00:e0:4b:6e:9b:2b mtu 1500 DHCP IP-Config: eth0 guessed broadcast address 172.16.0.255 IP-Config: eth0 complete (dhcp from 172.16.0.254): address: 172.16.0.78 broadcast: 172.16.0.255 netmask: 255.255.255.0 gateway: 172.16.0.254 dns0 : 8.8.8.8 dns1 : 0.0.0.0 domain : lava.lan rootserver: 172.16.0.254 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 7.700843] systemd[1]: System time before build time, advancing clock. <30>[ 7.756617] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 7.757604] systemd[1]: Detected architecture arm64. Welcome to [1mDebian GNU/Linux 11 (bullseye)[0m! <30>[ 7.807784] systemd[1]: Set hostname to . <30>[ 8.377484] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 8.386604] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 8.386622] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 8.389200] systemd[1]: Created slice system-getty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-getty.slice[0m. [[0;32m OK [0m] Created slice [0;1;39msyste<30>[ 8.434247] systemd[1]: Created slice system-modprobe.slice. m-modprobe.slice[0m. [[0;32m OK [<30>[ 8.458891] systemd[1]: Created slice system-serial\x2dgetty.slice. 0m] Created slice [0;1;39msystem-serial\x2dgetty.slice[0m. [[0;32m OK [<30>[ 8.482520] systemd[1]: Created slice User and Session Slice. 0m] Created slice [0;1;39mUser and Session Slice[0m. [[0;32m OK [<30>[ 8.505901] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. 0m] Started [0;1;39mDispatch Password …ts to Console Directory Watch[0m. [[0;32m OK [0m] Started [0;1;39mForward Pas<30>[ 8.529855] systemd[1]: Started Forward Password Requests to Wall Directory Watch. sword R…uests to Wall Directory Watch[0m. [[0;32m OK [0m] Reached target [0;1;39mLoca<30>[ 8.553756] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. l Encrypted Volu<30>[ 8.553912] systemd[1]: Reached target Local Encrypted Volumes. mes[0m. [[0;32m OK [<30>[ 8.589634] systemd[1]: Reached target Paths. 0m] Reached target [0;1;39mPaths[0m. [[0;32m OK [<30>[ 8.609584] systemd[1]: Reached target Remote File Systems. 0m] Reached target [0;1;39mRemote File Systems[0m. [[0;32m OK [<30>[ 8.629572] systemd[1]: Reached target Slices. 0m] Reached target [0;1;39mSlices[0m. [[0;32m OK [<30>[ 8.649644] systemd[1]: Reached target Swap. 0m] Reached target [0;1;39mSwap[0m. [[0;32m OK [<30>[ 8.669893] systemd[1]: Listening on initctl Compatibility Named Pipe. 0m] Listening on [0;1;39minitctl Compatibility Named Pipe[0m. [[0;32m OK [0m] Listening on<30>[ 8.694786] systemd[1]: Listening on Journal Audit Socket. [0;1;39mJournal Audit Socket[0m. [[0;32m OK [0m] Listening on [0;1;39mJourna<30>[ 8.718623] systemd[1]: Listening on Journal Socket (/dev/log). l Socket (/dev/log)[0m. [[0;32m OK [0m] Listening on [0;1;39mJourna<30>[ 8.742248] systemd[1]: Listening on Journal Socket. l Socket[0m. [[0;32m OK [0m] Listening on<30>[ 8.763335] systemd[1]: Listening on Network Service Netlink Socket. [0;1;39mNetwork Service Netlink Socket[0m. [[0;32m OK [0m] Listening on [0;1;39mudev C<30>[ 8.789900] systemd[1]: Listening on udev Control Socket. ontrol Socket[0m. [[0;32m OK [0m] Listening on<30>[ 8.810690] systemd[1]: Listening on udev Kernel Socket. [0;1;39mudev Kernel Socket[0m. Mountin<30>[ 8.840150] systemd[1]: Mounting Huge Pages File System... g [0;1;39mHuge Pages File System[0m... Mountin<30>[ 8.864022] systemd[1]: Mounting POSIX Message Queue File System... g [0;1;39mPOSIX Message Queue File System[0m... Mountin<30>[ 8.889254] systemd[1]: Mounting Kernel Debug File System... g [0;1;39mKernel Debug File System[0m... <30>[ 8.914090] systemd[1]: Condition check resulted in Kernel Trace File System being skipped. Startin<30>[ 8.918216] systemd[1]: Starting Create list of static device nodes for the current kernel... g [0;1;39mCreate list of st…odes for the current kernel[0m... Starting [0;1;39mLoad Kernel Module co<30>[ 8.957650] systemd[1]: Starting Load Kernel Module configfs... nfigfs[0m... Startin<30>[ 8.981238] systemd[1]: Starting Load Kernel Module drm... g [0;1;39mLoad Kernel Module drm[0m... Startin<30>[ 9.005339] systemd[1]: Starting Load Kernel Module fuse... g [0;1;39mLoad Kernel Module fuse[0m... <6>[ 9.027111] fuse: init (API version 7.32) Startin<30>[ 9.028161] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. g [0;1;39mJourn<30>[ 9.030894] systemd[1]: Starting Journal Service... al Service[0m... Startin<30>[ 9.066753] systemd[1]: Starting Load Kernel Modules... g [0;1;39mLoad Kernel Modules[0m... Starting [0;1;39mRemou<30>[ 9.087930] systemd[1]: Starting Remount Root and Kernel File Systems... nt Root and Kernel File Systems[0m... Starting [0;1;39mColdp<30>[ 9.111790] systemd[1]: Starting Coldplug All udev Devices... lug All udev Devices[0m... [[0;32m OK [<30>[ 9.136560] systemd[1]: Mounted Huge Pages File System. 0m] Mounted [0;1;39mHuge Pages File System[0m. [[0;32m OK [0m] Mounted [0;1;39mPOSIX Messa<30>[ 9.157980] systemd[1]: Mounted POSIX Message Queue File System. ge Queue File System[0m. [[0;32m OK [0m] Mounted [0;1;39mKernel Debu<30>[ 9.181973] systemd[1]: Mounted Kernel Debug File System. g File System[0m. [[0;32m OK [0m] Finished [0;1;39mCreate lis<30>[ 9.202435] systemd[1]: Finished Create list of static device nodes for the current kernel. t of st… nodes for the current kernel[0m. [[0;32m OK [0m] Finished [0<30>[ 9.230494] systemd[1]: modprobe@configfs.service: Succeeded. ;1;39mLoad Kernel Module configf<30>[ 9.231028] systemd[1]: Finished Load Kernel Module configfs. s[0m. [[0;32m OK [<30>[ 9.258357] systemd[1]: modprobe@drm.service: Succeeded. 0m] Finished [0;1;39mLoad Kernel Module drm[0m. <30>[ 9.258872] systemd[1]: Finished Load Kernel Module drm. [[0;32m OK [<30>[ 9.282408] systemd[1]: modprobe@fuse.service: Succeeded. 0m] Finished [0<30>[ 9.282942] systemd[1]: Finished Load Kernel Module fuse. ;1;39mLoad Kernel Module fuse[0m. [[0;32m OK [0m] Started [0;1;39mJournal Ser<30>[ 9.318035] systemd[1]: Started Journal Service. vice[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Modules[0m. [[0;32m OK [0m] Finished [0;1;39mRemount Root and Kernel File Systems[0m. Mounting [0;1;39mFUSE Control File System[0m... Mounting [0;1;39mKernel Configuration File System[0m... Starting [0;1;39mFlush Journal to Persistent Storage[0m... Starting [0;1;39mLoad/Save Random Seed[0m... <46>[ 9.449957] systemd-journald[215]: Received client request to flush runtime journal. Starting [0;1;39mApply Kernel Variables[0m... Starting [0;1;39mCreate System Users[0m... [[0;32m OK [0m] Mounted [0;1;39mFUSE Control File System[0m. [[0;32m OK [0m] Mounted [0;1;39mKernel Configuration File System[0m. [[0;32m OK [0m] Finished [0;1;39mColdplug All udev Devices[0m. [[0;32m OK [0m] Finished [0;1;39mLoad/Save Random Seed[0m. [[0;32m OK [0m] Finished [0;1;39mApply Kernel Variables[0m. [[0;32m OK [0m] Finished [0;1;39mFlush Journal to Persistent Storage[0m. [[0;32m OK [0m] Finished [0;1;39mCreate System Users[0m. Starting [0;1;39mCreate Static Device Nodes in /dev[0m... [[0;32m OK [0m] Finished [0;1;39mCreate Static Device Nodes in /dev[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems (Pre)[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems[0m. Starting [0;1;39mCreate Volatile Files and Directories[0m... Starting [0;1;39mRule-based Manage…for Device Events and Files[0m... [[0;32m OK [0m] Started [0;1;39mRule-based Manager for Device Events and Files[0m. Starting [0;1;39mNetwork Service[0m... [[0;32m OK [0m] Finished [0;1;39mCreate Volatile Files and Directories[0m. Starting [0;1;39mUpdate UTMP about System Boot/Shutdown[0m... [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Boot/Shutdown[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Initialization[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt download activities[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt upgrade and clean activities[0m. [[0;32m OK [0m] Started [0;1;39mPeriodic ext4 Onli…ata Check for All Filesystems[0m. [[0;32m OK [0m] Started [0;1;39mDiscard unused blocks once a week[0m. [[0;32m OK [0m] Started [0;1;39mDaily Cleanup of Temporary Directories[0m. [[0;32m OK [0m] Reached target [0;1;39mTimers[0m. [[0;32m OK [0m] Listening on [0;1;39mD-Bus System Message Bus Socket[0m. [[0;32m OK [0m] Reached target [0;1;39mSockets[0m. [[0;32m OK [0m] Reached target [0;1;39mBasic System[0m. [[0;32m OK [0m] Started [0;1;39mD-Bus System Message Bus[0m. Starting [0;1;39mRemove Stale Onli…t4 Metadata Check Snapshots[0m... Starting [0;1;39mUser Login Management[0m... [[0;32m OK [0m] Started [0;1;39mNetwork Service[0m. Starting [0;1;39mNetwork Name Resolution[0m... [[0;32m OK [0m] Started [0;1;39mUser Login Management[0m. [[0;32m OK [0m] Finished [0;1;39mRemove Stale Onli…ext4 Metadata Check Snapshots[0m. [[0;32m OK [0m] Started [0;1;39mNetwork Name Resolution[0m. [[0;32m OK [0m] Reached target [0;1;39mNetwork[0m. [[0;32m OK [0m] Reached target [0;1;39mHost and Network Name Lookups[0m. Starting [0;1;39mPermit User Sessions[0m... [[0;32m OK [0m] Finished [0;1;39mPermit User Sessions[0m. [[0;32m OK [0m] Started [0;1;39mGetty on tty1[0m. [[0;32m OK [0m] Found device [0;1;39m/dev/ttyS0[0m. [[0;32m OK [0m] Started [0;1;39mSerial Getty on ttyS0[0m. [[0;32m OK [0m] Reached target [0;1;39mLogin Prompts[0m. [[0;32m OK [0m] Reached target [0;1;39mMulti-User System[0m. [[0;32m OK [0m] Reached target [0;1;39mGraphical Interface[0m. Starting [0;1;39mUpdate UTMP about System Runlevel Changes[0m... [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Runlevel Changes[0m. Debian GNU/Linux 11 debian-bullseye-arm64 ttyS0 debian-bullseye-arm64 login: root (automatic login) Linux debian-bullseye-arm64 5.10.145-cip17-rt7 #1 SMP PREEMPT Sat Oct 1 19:12:27 UTC 2022 aarch64 The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/177722/extract-nfsrootfs-kwubdn1o' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/177722/extract-nfsrootfs-kwubdn1o' / # export NFS_SERVER_IP='10.228.65.1' export NFS_SERVER_IP='10.228.65.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-177722/environment . /lava-177722/environment / # /lava-177722/bin/lava-test-runner /lava-177722/0 /lava-177722/bin/lava-test-runner /lava-177722/0 + export TESTRUN_ID=0_dmesg + cd /lava-177722/0/tests/0_dmesg + cat uuid + UUID=177722_1.6.2.4.1 + set +x + KERNELCI_LAVA<8>[ 12.249870] =y /bin/sh /opt/kernelci/dmesg.sh <8>[ 12.313122] <8>[ 12.366166] + set +x <8>[ 12.406595] [ 12.407163] R EXIT> / #