[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (4 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 7922952/tftp-deploy-24ll6mh0/kernel/zImage tftp 0x10000000 7922952/tftp-deploy-24ll6mh0/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '7922952/tftp-deploy-24ll6mh0/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################### 6.3 MiB/s done Bytes transferred = 9806336 (95a200 hex) => tftp 0x14000000 7922952/tftp-deploy-24ll6mh0/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 7922952/tftp-deploy-24ll6mh0/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '7922952/tftp-deploy-24ll6mh0/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################################################### 6 MiB/s done Bytes transferred = 12206003 (ba3fb3 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 7922952/tftp-deploy-24ll6mh0/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 7922952/tftp-deploy-24ll6mh0/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '7922952/tftp-deploy-24ll6mh0/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 6.7 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/7922952/extract-nfsrootfs-xk079lwl,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/7922952/extract-nfsrootfs-xk079lwl,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x95a200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12205939 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.153-cip19-rt8 (KernelCI@build-j483795-arm-gcc-10-defconfig-preempt-rt-8kc47) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT_RT Wed Nov 9 21:40:45 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 16 pages/cpu s34912 r8192 d22432 u65536 [ 0.000000] pcpu-alloc: s34912 r8192 d22432 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/7922952/extract-nfsrootfs-xk079lwl,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 936388K/1048576K available (14336K kernel code, 2355K rwdata, 5372K rodata, 2048K init, 420K bss, 46652K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms. <6>[ 0.000000] rcu: RCU_SOFTIRQ processing moved to rcuc kthreads. <6>[ 0.000000] No expedited grace period (rcu_normal_after_boot). <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008438] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022176] Console: colour dummy device 80x30 <6>[ 0.024074] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034485] pid_max: default: 32768 minimum: 301 <6>[ 0.039518] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046938] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055749] CPU: Testing write buffer coherency: ok <6>[ 0.060049] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065656] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072289] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079749] rcu: Hierarchical SRCU implementation. <6>[ 0.087192] EFI services will not be available. <6>[ 0.089550] smp: Bringing up secondary CPUs ... <6>[ 0.095165] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.099835] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.106566] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.111056] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.117743] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.122279] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127739] smp: Brought up 1 node, 4 CPUs <6>[ 0.131935] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.138416] CPU: All CPU(s) started in SVC mode. <6>[ 0.143914] devtmpfs: initialized <6>[ 0.157800] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.163185] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.173054] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.183375] pinctrl core: initialized pinctrl subsystem <6>[ 0.188200] DMI not present or invalid. <6>[ 0.191011] NET: Registered protocol family 16 <6>[ 0.199860] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.207098] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.207357] cpuidle: using governor menu <6>[ 0.215265] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.417428] vdd1p1: supplied by regulator-dummy <6>[ 0.427547] vdd3p0: supplied by regulator-dummy <6>[ 0.437648] vdd2p5: supplied by regulator-dummy <6>[ 0.447716] vddarm: supplied by regulator-dummy <6>[ 0.458024] vddpu: supplied by regulator-dummy <6>[ 0.467746] vddsoc: supplied by regulator-dummy <6>[ 0.838909] No ATAGs? <6>[ 0.839077] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.846853] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.858119] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.870131] Serial: AMBA PL011 UART driver <6>[ 0.874338] printk: console [ramoops-1] enabled <6>[ 0.876694] pstore: Registered ramoops as persistent store backend <6>[ 0.882921] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.931315] iommu: Default domain type: Translated <6>[ 0.933963] vgaarb: loaded <5>[ 0.937662] SCSI subsystem initialized <7>[ 0.940884] libata version 3.00 loaded. <6>[ 0.944985] usbcore: registered new interface driver usbfs <6>[ 0.950550] usbcore: registered new interface driver hub <6>[ 0.956014] usbcore: registered new device driver usb <6>[ 0.963466] i2c i2c-0: IMX I2C adapter registered <6>[ 0.968501] i2c i2c-1: IMX I2C adapter registered <6>[ 0.972881] i2c i2c-2: IMX I2C adapter registered <6>[ 0.977924] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.981368] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.990854] PTP clock support registered <6>[ 0.999208] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.165451] NET: Registered protocol family 2 <6>[ 2.167705] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.176390] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.183727] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.191704] TCP bind hash table entries: 8192 (order: 5, 229376 bytes, linear) <6>[ 2.199522] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.205947] UDP hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 2.212723] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 2.220210] NET: Registered protocol family 1 <6>[ 2.225222] RPC: Registered named UNIX socket transport module. <6>[ 2.230740] RPC: Registered udp transport module. <6>[ 2.235607] RPC: Registered tcp transport module. <6>[ 2.240642] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.247272] PCI: CLS 0 bytes, default 64 <6>[ 2.252047] Trying to unpack rootfs image as initramfs... <6>[ 3.296680] Freeing initrd memory: 11920K <4>[ 3.298550] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.305919] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.316492] Initialise system trusted keyrings <6>[ 3.318907] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.334770] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.339154] NFS: Registering the id_resolver key type <5>[ 3.343408] Key type id_resolver registered <5>[ 3.347760] Key type id_legacy registered <6>[ 3.352184] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.358983] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.366730] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.371914] Key type asymmetric registered <5>[ 3.375601] Asymmetric key parser 'x509' registered <6>[ 3.380881] bounce: pool size: 64 pages <6>[ 3.384855] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.392502] io scheduler mq-deadline registered <6>[ 3.397263] io scheduler kyber registered <4>[ 3.450020] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.456936] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.467047] mxs-dma 110000.dma-apbh: initialized <6>[ 3.560458] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.569952] SuperH (H)SCI(F) driver initialized <6>[ 3.573272] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.582409] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.589840] printk: console [ttymxc1] enabled <6>[ 3.594242] printk: bootconsole [ec_imx21] disabled <6>[ 3.589840] printk: console [ttymxc1] enabled <6>[ 3.594242] printk: bootconsole [ec_imx21] disabled <6>[ 3.601334] msm_serial: driver initialized <6>[ 3.601651] STMicroelectronics ASC driver initialized <6>[ 3.603972] STM32 USART driver initialized <4>[ 3.616517] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.616737] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.617202] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.629609] brd: module loaded <6>[ 3.643862] loop: module loaded <6>[ 3.648641] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.648657] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.648667] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.648677] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.648774] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.648986] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.649081] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.652210] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.652238] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.652255] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.654202] scsi host0: ahci-imx <6>[ 3.654734] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.670625] CAN device driver interface <6>[ 3.672186] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.676257] pps pps0: new PPS source ptp0 <6>[ 3.697202] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.699121] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.699127] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.699302] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.699309] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.706676] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.706733] usbcore: registered new interface driver pegasus <6>[ 3.706791] usbcore: registered new interface driver asix <6>[ 3.706834] usbcore: registered new interface driver ax88179_178a <6>[ 3.706874] usbcore: registered new interface driver cdc_ether <6>[ 3.706932] usbcore: registered new interface driver smsc75xx <6>[ 3.707000] usbcore: registered new interface driver smsc95xx <6>[ 3.707043] usbcore: registered new interface driver net1080 <6>[ 3.707085] usbcore: registered new interface driver cdc_subset <6>[ 3.707126] usbcore: registered new interface driver zaurus <6>[ 3.707212] usbcore: registered new interface driver cdc_ncm <6>[ 3.711589] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.711597] ehci-pci: EHCI PCI platform driver <6>[ 3.711651] ehci-platform: EHCI generic platform driver <6>[ 3.711994] ehci-orion: EHCI orion driver <6>[ 3.712259] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.712491] ehci-st: EHCI STMicroelectronics driver <6>[ 3.712720] ehci-exynos: EHCI Exynos driver <6>[ 3.712943] ehci-atmel: EHCI Atmel driver <6>[ 3.713163] tegra-ehci: Tegra EHCI driver <6>[ 3.713434] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.713460] ohci-pci: OHCI PCI platform driver <6>[ 3.713512] ohci-platform: OHCI generic platform driver <6>[ 3.713823] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.714059] ohci-st: OHCI STMicroelectronics driver <6>[ 3.714293] ohci-atmel: OHCI Atmel driver <6>[ 3.715550] usbcore: registered new interface driver usb-storage <6>[ 3.725878] i2c /dev entries driver <6>[ 3.750676] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.750685] sdhci: Copyright(c) Pierre Ossman <6>[ 3.753918] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.756290] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.757698] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.757752] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.757982] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.763299] usbcore: registered new interface driver usbhid <6>[ 3.763309] usbhid: USB HID core driver <6>[ 3.771315] NET: Registered protocol family 10 <6>[ 3.772816] Segment Routing with IPv6 <6>[ 3.772902] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.773661] NET: Registered protocol family 17 <6>[ 3.773682] can: controller area network core <6>[ 3.773787] NET: Registered protocol family 29 <6>[ 3.773795] can: raw protocol <6>[ 3.773804] can: broadcast manager protocol <6>[ 3.773821] can: netlink gateway - max_hops=1 <5>[ 3.774336] Key type dns_resolver registered <6>[ 3.777816] ThumbEE CPU extension supported. <5>[ 3.777855] Registering SWP/SWPB emulation handler <6>[ 3.778395] printk: console [ttymxc1]: printing thread started <6>[ 3.778516] printk: console [ramoops-1]: printing thread started <5>[ 3.778548] Loading compiled-in X.509 certificates <6>[ 3.784150] pstore: Using crash dump compression: deflate <6>[ 3.790730] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.792968] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <4>[ 3.818147] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.818324] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.820311] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.829679] mmc2: new high speed SDHC card at address e624 <4>[ 3.830451] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.830710] mmcblk2: mmc2:e624 SL16G 14.8 GiB <6>[ 3.834716] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.834768] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 3.839342] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.839350] GPT:29296874 != 31116287 <4>[ 3.839355] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.839358] GPT:29296874 != 31116287 <4>[ 3.839362] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.839400] mmcblk2: p1 p2 p3 <6>[ 3.859293] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.860116] hub 1-0:1.0: USB hub found <6>[ 3.860161] hub 1-0:1.0: 1 port detected <6>[ 3.863149] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 3.868915] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.869111] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.871119] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.876857] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.877028] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.878756] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.882463] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 3.888327] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.888493] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.890418] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.981269] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.981321] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.981329] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.994181] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.149245] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.350374] hub 1-1:1.0: USB hub found <6>[ 4.350585] hub 1-1:1.0: 3 ports detected <4>[ 4.356942] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.357109] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.358907] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.119782] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.139352] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.169531] Sending DHCP requests ., OK <6>[ 7.209490] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 <6>[ 7.209521] IP-Config: Complete: <6>[ 7.209528] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.209554] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) <6>[ 7.209567] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.209583] nameserver0=192.168.201.1 <6>[ 7.220472] Freeing unused kernel memory: 2048K <6>[ 7.249772] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 <6>[ 8.479678] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 8.522185] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.524932] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.528858] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.551607] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.576960] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.578973] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.581573] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.694328] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.694550] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.695576] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.696054] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.696494] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.697367] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.698086] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.816286] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.816536] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.821448] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.821870] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.822308] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.822405] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.822641] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.822738] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.822752] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.824641] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.845053] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.845275] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.845494] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.845692] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.847640] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.936324] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.943394] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.964918] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.965312] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.965644] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.965868] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.970392] caam 2100000.crypto: Entropy delay = 3200 <6>[ 9.031226] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 9.090228] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 9.095389] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <6>[ 9.099072] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 9.099098] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 9.099107] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 9.099435] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.099541] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 9.159098] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 9.220034] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.240796] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.257334] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.257613] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.257892] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.258132] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.296325] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.381825] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 9.382226] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 9.387264] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 9.411104] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.443611] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.444314] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.444606] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.444864] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.448778] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.541539] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.557960] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.580263] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.585196] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.585537] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.585796] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.996705] caam algorithms registered in /proc/crypto <6>[ 9.998547] caam 2100000.crypto: registering rng-caam <4>[ 10.015322] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 10.124901] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 10.145492] panel-simple panel-lcd: Specify missing connector_type <6>[ 10.174148] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 10.174387] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 10.174609] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 10.174821] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Begin: Loading essential drivers <4>[ 10.178138] panel-simple panel-lvds0: supply power not found, using dummy regulator ... <5>[ 10.187790] random: crng init done done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... done. IP-Config: eth0 hardware address 00:19:b8:08:f0:fd mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.37 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-7 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 11.533165] systemd[1]: System time before build time, advancing clock. <30>[ 11.607791] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 11.608719] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 11.672744] systemd[1]: Set hostname to . [ OK ] Created slice system-getty.slice[0<30>[ 12.640055] systemd[1]: Queued start job for default target Graphical Interface. m. <28>[ 12.642089] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 12.642114] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 12.643070] systemd[1]: Created slice system-getty.slice. <30>[ 12.671433] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 12.720887] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice User and Session Slice. <30>[ 12.749947] systemd[1]: Created slice User and Session Slice. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 12.780422] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 12.810378] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Local Encrypted Volumes. <30>[ 12.839715] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 12.839975] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Paths. <30>[ 12.870540] systemd[1]: Reached target Paths. [ OK ] Reached target Remote File Systems. <30>[ 12.899540] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Slices. <30>[ 12.929773] systemd[1]: Reached target Slices. [ OK ] Reached target Swap. <30>[ 12.959895] systemd[1]: Reached target Swap. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 12.990715] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on Journal Socket (/dev/l<30>[ 13.051441] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 13.053587] systemd[1]: Listening on Journal Socket (/dev/log). og). [ OK ] Listening on Journal Socket. <30>[ 13.100415] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 13.132315] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on udev Control Socket. <30>[ 13.161967] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 13.191254] systemd[1]: Listening on udev Kernel Socket. <30>[ 13.220789] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 13.221798] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. Mounting Kernel<30>[ 13.230211] systemd[1]: Mounting Kernel Debug File System... Debug File System... Mounting Kernel Trace File System... <30>[ 13.285264] systemd[1]: Mounting Kernel Trace File System... Starting Create list of st…odes for the current kernel... <30>[ 13.339666] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Load Kernel Module configfs... <30>[ 13.374003] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module drm... <30>[ 13.404220] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module fuse... <30>[ 13.434090] systemd[1]: Starting Load Kernel Module fuse... Starting Journa<30>[ 13.463315] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. l Service... <30>[ 13.468070] systemd[1]: Starting Journal Service... Starting Load K<30>[ 13.497120] systemd[1]: Starting Load Kernel Modules... ernel Modules... Starting Remount Root and Kernel File Systems<30>[ 13.534108] systemd[1]: Starting Remount Root and Kernel File Systems... [0m... Starting Coldplug All udev Devices... <30>[ 13.573671] systemd[1]: Starting Coldplug All udev Devices... [ OK ] Mounted Kernel Debug File System[0<30>[ 13.604995] systemd[1]: Mounted Kernel Debug File System. m. [ OK ] Mounted Kernel Trace File System. <30>[ 13.641124] systemd[1]: Mounted Kernel Trace File System. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 13.671531] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished [0;<30>[ 13.723311] systemd[1]: modprobe@configfs.service: Succeeded. 1;39mLoad Kernel Module configfs<30>[ 13.726700] systemd[1]: Finished Load Kernel Module configfs. [0m. [ OK ] Finished Load Kernel Module drm<30>[ 13.771987] systemd[1]: modprobe@drm.service: Succeeded. . <30>[ 13.773725] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished [0;<30>[ 13.793805] systemd[1]: modprobe@fuse.service: Succeeded. 1;39mLoad Kernel Module fuse.<30>[ 13.796238] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. <30>[ 13.842472] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. <30>[ 13.871712] systemd[1]: Finished Remount Root and Kernel File Systems. [ OK ] Started Journal Service. <30>[ 13.900075] systemd[1]: Started Journal Service. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... <46>[ 14.041846] systemd-journald[327]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create Volatile Files and Directories. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Getty on tty1. [ OK ] Started User Login Management. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Found device /dev/ttymxc1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.153-cip19-rt8 #1 SMP PREEMPT_RT Wed Nov 9 21:40:45 UTC 2022 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/7922952/extract-nfsrootfs-xk079lwl' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/7922952/extract-nfsrootfs-xk079lwl' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-7922952/environment . /lava-7922952/environment / # /lava-7922952/bin/lava-test-runner /lava-7922952/0 /lava-7922952/bin/lava-test-runner /lava-7922952/0 + export TESTRUN_ID=0_dmesg + cd /lava-7922952/0/tests/0_dmesg + cat uuid + UUID=7922952_1.6.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 28.812728] <8>[ 28.926162] <8>[ 29.008141] + set +x / # <8>[ 29.091047] <8>[ 29.092203] # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-7922952/environment / # . /lava-7922952/environment/lava-7922952/bin/lava-test-runner /lava-7922952/1 / # /lava-7922952/bin/lava-test-runner /lava-7922952/1 + export TESTRUN_ID=1_bootrr + cd /lava-7922952/1/tests/1_bootrr + cat uuid + UUID=7922952_1.6.2.4.5<8>[ 29.708393] + set +x + export PATH=/opt/bootrr/helpers:/lava-7922952/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr + sh helpers/bootrr-auto /lava-7922952/1/../bin/lava-test-case <8>[ 30.828730] + set +x