Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3009 device /dev/ttyimx7d-sdb-2 [115200 N81] (Debian GNU/Linux) U-Boot 2016.03-imx_v2016.03_4.1.15_2.0.0_ga+g0ec2a01 (Nov 11 2016 - 03:13:54 -0600) CPU: Freescale i.MX7D rev1.3 996 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 25C Reset cause: POR Board: i.MX7D SABRESD RevA I2C: ready DRAM: 1 GiB PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11 MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - bad CRC, using default environment Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc0 is current device Net: FEC0 Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.196 (1938 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80800000 1098238/tftp-deploy-8d0fbbq1/kernel/zImage tftp 0x80800000 1098238/tftp-deploy-8d0fbbq1/kernel/zImage Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.196; sending through gateway 172.16.1.4 Filename '1098238/tftp-deploy-8d0fbbq1/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 9.2 MiB/s done Bytes transferred = 9679360 (93b200 hex) => tftp 0x86800000 1098238/tftp-deploy-8d0fbbq1/ramdisk/ramdisk.cpio.gz.uboot tftp 0x86800000 1098238/tftp-deploy-8d0fbbq1/ramdisk/ramdisk.cpio.gz.uboot Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.196; sending through gateway 172.16.1.4 Filename '1098238/tftp-deploy-8d0fbbq1/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 10.6 MiB/s done Bytes transferred = 16061872 (f515b0 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x83000000 1098238/tftp-deploy-8d0fbbq1/dtb/imx7d-sdb.dtb tftp 0x83000000 1098238/tftp-deploy-8d0fbbq1/dtb/imx7d-sdb.dtb Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.196; sending through gateway 172.16.1.4 Filename '1098238/tftp-deploy-8d0fbbq1/dtb/imx7d-sdb.dtb'. Load address: 0x83000000 Loading: *### 7.2 MiB/s done Bytes transferred = 37996 (946c hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x80800000 0x86800000 0x83000000 bootz 0x80800000 0x86800000 0x83000000 Kernel image @ 0x80800000 [ 0x000000 - 0x93b200 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16061808 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300c46b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.153-cip19-rt8 (KernelCI@build-j483897-arm-gcc-10-defconfig-t7ggz) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Nov 9 21:45:55 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX7 SabreSD Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x30860000 (options '') [ 0.000000] printk: bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xbc000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 16 pages/cpu s33612 r8192 d23732 u65536 [ 0.000000] pcpu-alloc: s33612 r8192 d23732 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933832K/1048576K available (13312K kernel code, 2324K rwdata, 5344K rodata, 2048K init, 417K bss, 49208K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns <6>[ 0.000001] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns <6>[ 0.008310] Switching to timer-based delay loop, resolution 125ns <6>[ 0.016019] Switching to timer-based delay loop, resolution 41ns <6>[ 0.020998] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.029134] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.043639] Console: colour dummy device 80x30 <6>[ 0.045556] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.056200] pid_max: default: 32768 minimum: 301 <6>[ 0.061255] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.068717] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.077521] CPU: Testing write buffer coherency: ok <6>[ 0.082238] CPU0: update cpu_capacity 1024 <6>[ 0.086282] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.092983] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.100553] rcu: Hierarchical SRCU implementation. <6>[ 0.107720] EFI services will not be available. <6>[ 0.109905] smp: Bringing up secondary CPUs ... <6>[ 0.115178] smp: Brought up 1 node, 1 CPU <6>[ 0.118772] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.125288] CPU: All CPU(s) started in SVC mode. <6>[ 0.130715] devtmpfs: initialized <6>[ 0.142015] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.147428] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.157328] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.166806] pinctrl core: initialized pinctrl subsystem <6>[ 0.171839] DMI not present or invalid. <6>[ 0.175100] NET: Registered protocol family 16 <6>[ 0.180928] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.188639] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.188759] cpuidle: using governor menu <6>[ 0.196949] No ATAGs? <6>[ 0.199019] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.207288] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.216350] Serial: AMBA PL011 UART driver <6>[ 0.266827] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver <6>[ 0.272596] imx7d-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver <6>[ 0.325484] iommu: Default domain type: Translated <6>[ 0.328767] vgaarb: loaded <5>[ 0.331844] SCSI subsystem initialized <7>[ 0.335155] libata version 3.00 loaded. <6>[ 0.339218] usbcore: registered new interface driver usbfs <6>[ 0.344794] usbcore: registered new interface driver hub <6>[ 0.350327] usbcore: registered new device driver usb <6>[ 0.363727] i2c i2c-0: IMX I2C adapter registered <6>[ 0.371727] i2c i2c-1: IMX I2C adapter registered <6>[ 0.374418] i2c i2c-2: IMX I2C adapter registered <6>[ 0.384620] i2c i2c-3: IMX I2C adapter registered <6>[ 0.388089] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.392029] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.401474] PTP clock support registered <6>[ 0.409383] clocksource: Switched to clocksource arch_sys_counter <6>[ 1.513547] NET: Registered protocol family 2 <6>[ 1.515632] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.524261] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.531752] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.539842] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.547322] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.553966] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.560815] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.568281] NET: Registered protocol family 1 <6>[ 1.573562] RPC: Registered named UNIX socket transport module. <6>[ 1.578949] RPC: Registered udp transport module. <6>[ 1.583983] RPC: Registered tcp transport module. <6>[ 1.588923] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.595683] PCI: CLS 0 bytes, default 64 <6>[ 1.600411] Trying to unpack rootfs image as initramfs... <6>[ 2.929330] Freeing initrd memory: 15688K <6>[ 2.931511] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 2.940957] Initialise system trusted keyrings <6>[ 2.944390] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.957943] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.962138] NFS: Registering the id_resolver key type <5>[ 2.966592] Key type id_resolver registered <5>[ 2.971046] Key type id_legacy registered <6>[ 2.975413] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 2.982320] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 2.990051] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.995169] Key type asymmetric registered <5>[ 2.999013] Asymmetric key parser 'x509' registered <6>[ 3.004261] bounce: pool size: 64 pages <6>[ 3.008324] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.016006] io scheduler mq-deadline registered <6>[ 3.020814] io scheduler kyber registered <4>[ 3.048416] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 3.066160] mxs-dma 33000000.dma-apbh: initialized <4>[ 3.081160] imx-sdma 30bd0000.sdma: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 <6>[ 3.088211] imx-sdma 30bd0000.sdma: external firmware not found, using ROM firmware <6>[ 3.151603] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.160041] SuperH (H)SCI(F) driver initialized <3>[ 3.162809] clk: failed to reparent uart1_src to pll_sys_main_240m_clk: -16 <6>[ 3.169560] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 58, base_baud = 1500000) is a IMX <6>[ 3.178463] printk: console [ttymxc0] enabled <6>[ 3.182988] printk: bootconsole [ec_imx6q0] disabled <6>[ 3.178463] printk: console [ttymxc0] enabled <6>[ 3.182988] printk: bootconsole [ec_imx6q0] disabled <6>[ 3.189227] 30a80000.serial: ttymxc5 at MMIO 0x30a80000 (irq = 67, base_baud = 15000000) is a IMX <6>[ 3.190700] msm_serial: driver initialized <6>[ 3.190926] STMicroelectronics ASC driver initialized <6>[ 3.192617] STM32 USART driver initialized <6>[ 3.212665] brd: module loaded <6>[ 3.220652] loop: module loaded <6>[ 3.235798] CAN device driver interface <6>[ 3.237020] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.242657] pps pps0: new PPS source ptp0 <3>[ 3.243609] fec 30bf0000.ethernet: Invalid MAC address: 00:00:00:00:00:00 <6>[ 3.243678] fec 30bf0000.ethernet: Using random MAC address: 4a:48:c6:a3:12:f9 <6>[ 4.290376] fec 30bf0000.ethernet eth0: registered PHC device 0 <6>[ 4.291812] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.291821] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.291895] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.291902] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.297311] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.297366] usbcore: registered new interface driver pegasus <6>[ 4.297416] usbcore: registered new interface driver asix <6>[ 4.297465] usbcore: registered new interface driver ax88179_178a <6>[ 4.297506] usbcore: registered new interface driver cdc_ether <6>[ 4.297557] usbcore: registered new interface driver smsc75xx <6>[ 4.297609] usbcore: registered new interface driver smsc95xx <6>[ 4.297649] usbcore: registered new interface driver net1080 <6>[ 4.297688] usbcore: registered new interface driver cdc_subset <6>[ 4.297738] usbcore: registered new interface driver zaurus <6>[ 4.297839] usbcore: registered new interface driver cdc_ncm <6>[ 4.301119] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.301129] ehci-pci: EHCI PCI platform driver <6>[ 4.301172] ehci-platform: EHCI generic platform driver <6>[ 4.301425] ehci-orion: EHCI orion driver <6>[ 4.301619] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.301774] ehci-st: EHCI STMicroelectronics driver <6>[ 4.301925] ehci-exynos: EHCI Exynos driver <6>[ 4.302072] ehci-atmel: EHCI Atmel driver <6>[ 4.302221] tegra-ehci: Tegra EHCI driver <6>[ 4.302400] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.302429] ohci-pci: OHCI PCI platform driver <6>[ 4.302478] ohci-platform: OHCI generic platform driver <6>[ 4.302704] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.302856] ohci-st: OHCI STMicroelectronics driver <6>[ 4.303006] ohci-atmel: OHCI Atmel driver <6>[ 4.304005] usbcore: registered new interface driver usb-storage <6>[ 4.311352] i2c /dev entries driver <3>[ 4.328783] CPUidle arm: CPU 0 failed to init idle CPU ops <6>[ 4.329310] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.329317] sdhci: Copyright(c) Pierre Ossman <6>[ 4.331825] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.333505] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.338393] sdhci-esdhc-imx 30b40000.mmc: Got CD GPIO <6>[ 4.338429] sdhci-esdhc-imx 30b40000.mmc: Got WP GPIO <6>[ 4.343714] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.344888] usbcore: registered new interface driver usbhid <6>[ 4.344898] usbhid: USB HID core driver <6>[ 4.351197] NET: Registered protocol family 10 <6>[ 4.352448] Segment Routing with IPv6 <6>[ 4.352525] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.353192] NET: Registered protocol family 17 <6>[ 4.353210] can: controller area network core <6>[ 4.353278] NET: Registered protocol family 29 <6>[ 4.353286] can: raw protocol <6>[ 4.353294] can: broadcast manager protocol <6>[ 4.353305] can: netlink gateway - max_hops=1 <5>[ 4.353867] Key type dns_resolver registered <6>[ 4.353985] ThumbEE CPU extension supported. <5>[ 4.353999] Registering SWP/SWPB emulation handler <6>[ 4.354468] printk: console [ttymxc0]: printing thread started <5>[ 4.354497] Loading compiled-in X.509 certificates <4>[ 4.394019] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 4.784778] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA <6>[ 4.785453] mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA <4>[ 4.789554] imx_usb 30b10000.usb: No over current polarity defined <4>[ 4.792036] imx_usb 30b20000.usb: No over current polarity defined <4>[ 4.797287] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 4.847274] imx_usb 30b10000.usb: No over current polarity defined <4>[ 4.849797] imx_usb 30b20000.usb: No over current polarity defined <4>[ 4.855084] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 4.888533] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA <6>[ 4.890228] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.892838] imx_usb 30b10000.usb: No over current polarity defined <4>[ 4.895358] imx_usb 30b20000.usb: No over current polarity defined <4>[ 4.900777] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 4.952169] imx_usb 30b10000.usb: No over current polarity defined <4>[ 4.954578] imx_usb 30b20000.usb: No over current polarity defined <4>[ 4.959949] pwm-backlight backlight: supply power not found, using dummy regulator <3>[ 4.987434] fec 30bf0000.ethernet eth0: Unable to connect to phy <3>[ 4.990918] IP-Config: Failed to open eth0 <3>[ 4.990933] IP-Config: No network devices available <6>[ 5.026120] Freeing unused kernel memory: 2048K <6>[ 5.026556] Run /init as init process <6>[ 5.044388] mmc0: new high speed SDHC card at address aaaa <4>[ 5.046683] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) <6>[ 5.047629] mmcblk0: mmc0:aaaa SA16G 14.8 GiB <6>[ 5.069573] mmcblk0: p1 p2 <4>[ 5.069860] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) <4>[ 5.083470] mmc1: queuing unknown CIS tuple 0x80 (6 bytes) <4>[ 5.106576] imx_usb 30b10000.usb: No over current polarity defined <4>[ 5.109040] imx_usb 30b20000.usb: No over current polarity defined <4>[ 5.114502] pwm-backlight backlight: supply power not found, using dummy regulator Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <6>[ 5.322412] mmc1: new ultra high speed SDR104 SDIO card at address 0001 <30>[ 5.340344] udevd[129]: starting version 3.2.9 <5>[ 5.341449] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.341738] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.341878] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 5.377061] udevd[129]: specified user 'tss' unknown <27>[ 5.377237] udevd[129]: specified group 'tss' unknown <30>[ 5.391153] udevd[130]: starting eudev-3.2.9 <6>[ 7.019966] gpio-expander@0 enforce active low on chipselect handle <4>[ 7.193078] imx_usb 30b10000.usb: No over current polarity defined <4>[ 7.195526] imx_usb 30b20000.usb: No over current polarity defined <4>[ 7.201000] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 7.331038] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 7.331291] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 7.331443] usb_phy_generic usbphynop3: deferred probe timeout, ignoring dependency <4>[ 7.331465] usb_phy_generic: probe of usbphynop3 failed with error -110 <4>[ 7.331723] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 7.331927] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 7.435146] imx_usb 30b10000.usb: No over current polarity defined <4>[ 7.642688] imx_usb 30b20000.usb: No over current polarity defined <6>[ 7.646253] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 7.646305] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 7.669426] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 7.670462] hub 1-0:1.0: USB hub found <6>[ 7.670519] hub 1-0:1.0: 1 port detected <4>[ 7.676902] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 8.621397] caam 30900000.crypto: Entropy delay = 3200 <6>[ 8.680851] caam 30900000.crypto: Instantiated RNG4 SH0 <6>[ 8.740263] caam 30900000.crypto: Instantiated RNG4 SH1 <6>[ 8.740279] caam 30900000.crypto: device ID = 0x0a16030000000000 (Era 8) <6>[ 8.740291] caam 30900000.crypto: job rings = 3, qi = 0 <4>[ 8.807813] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 9.176438] pwm-backlight backlight: supply power not found, using dummy regulator <5>[ 9.740282] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 10.292453] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <4>[ 10.292626] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 10.292646] cfg80211: failed to load regulatory.db <4>[ 10.374799] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 10.410674] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <4>[ 10.410986] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed with error -2 <4>[ 10.494812] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 10.993290] caam algorithms registered in /proc/crypto <6>[ 10.995035] caam 30900000.crypto: caam pkc algorithms registered in /proc/crypto <6>[ 10.995058] caam 30900000.crypto: registering rng-caam <4>[ 11.026292] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 11.076574] pwm-backlight backlight: supply power not found, using dummy regulator done Saving random seed: OK <5>[ 11.124409] random: dd: uninitialized urandom read (32 bytes read) Starting network: ip: RTNETLINK answers: File exists FAIL <5>[ 11.174211] random: crng init done Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh <3>[ 11.429447] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 export SHELL=/bin/sh / # . /lava-1098238/environment . /lava-1098238/environment / # /lava-1098238/bin/lava-test-runner /lava-1098238/0 /lava-1098238/bin/lava-test-runner /lava-1098238/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1098238/0/tests/0_dmesg + cat uuid + UUID=1098238_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 17.049569] <8>[ 17.095999] <8>[ 17.140434] + set +x <8>[ 17.184955] / # <8>[ 17.186366] # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1098238/environment / # . /lava-1098238/environment/lava-1098238/bin/lava-test-runner /lava-1098238/1 / # /lava-1098238/bin/lava-test-runner /lava-1098238/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1098238/1/tests/1_bootrr + cat uuid + UUID=1098238_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-1098238/1/../bin:/sbin:/usr/sbin:/bi<8>[ 22.921103] n:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-1098238/1/../bin/lava-test-case <8>[ 23.968670] /lava-1098238/1/../bin/lava-test-case <8>[ 25.013809] /lava-1098238/1/../bin/lava-test-case <8>[ 25.039253] + set +x <8>[ 25.058722] / #