connecting to NetworkSerialPort(target=Target(name='stm32mp157c-lxa-mc1-0', env=None), name='NetworkSerialPort', state=, avail=True, host='moxa.cuskci.stw.pengutronix.de', port=4003, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t moxa.cuskci.stw.pengutronix.de:4003 connected to 10.8.254.5 (port 4003) Escape character: Ctrl-\ Type the escape character to get to the prompt. NOTICE: CPU: STM32MP157C?? Rev.B NOTICE: Model: Linux Automation MC-1 board NOTICE: BL2: v2.4(release):v2.4 NOTICE: BL2: Built : 00:00:00, Dec 1 2020 NOTICE: BL2: Booting BL32 NOTICE: SP_MIN: v2.4(release):v2.4 NOTICE: SP_MIN: Built : 00:00:00, Dec 1 2020 barebox 2020.09.0 #1 2020-09-01T00:00:00+00:00 Board: Linux Automation MC-1 board STM32 RCC reset reason POR (MP_RSTSR: 0x00000015) stm32mp-init: detected STM32MP157C?? Rev.B stpmic1-i2c stpmic10: PMIC Chip Version: 0x10 psci psci.of: detected version 1.1 mdio_bus: miibus0: probed stm32_sdmmc 58005000.sdmmc@58005000.of: registered as mmc0 stm32_sdmmc 58007000.sdmmc@58007000.of: registered as mmc1 mmc1: detected MMC card version 5.0 mmc1: registered mmc1.boot0 mmc1: registered mmc1.boot1 mmc1: registered mmc1 remoteproc0: 10000000.m4@10000000.of is available netconsole: registered as netconsole-1 malloc space: 0xcfefe7e0 -> 0xdfdfcfbf (size 255 MiB) [?25h Hit m for menu or any to stop autoboot: 3 [1;32mbarebox@[1;36mLinux Automation MC-1 board:/[0m bootm -v -r /mnt/tftp/823140/tftp-deploy-kd7rk121/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/823140/tftp-deploy-kd7rk121/dtb/stm32mp157c-lxa-mc1.dtb /mnt/tftp/823140/tftp-deploy-kd7rk121/kernel/zImage [1;32mbarebox@[1;36mLinux Automation MC-1 board:/[0m bootm -v -r /mnt/tftp/823140/tftp-deploy-kd7rk121/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/823140/tftp-deploy-kd7rk121/dtb/stm32mp157c-lxa-mc1.dtb /mnt/tftp/823140/tftp-deploy-kd7rk121/kernel/zImage eth0: 1000Mbps full duplex link detected [33mWARNING:[0m eth0: No MAC address set. Using random address 6a:43:59:47:ca:61 T eth0: DHCP client bound to address 10.8.254.129 Loading ARM Linux zImage '/mnt/tftp/823140/tftp-deploy-kd7rk121/kernel/zImage' OS image not yet relocated Passing control to ARM zImage handler no OS load address, defaulting to 0xc2ec3000 no initrd load address, defaulting to 0xc391e000 Loaded initrd GZIP compressed '/mnt/tftp/823140/tftp-deploy-kd7rk121/ramdisk/ramdisk.cpio.gz' initrd is at 0xc391e000-0xc487fb18 Loading devicetree from '/mnt/tftp/823140/tftp-deploy-kd7rk121/dtb/stm32mp157c-lxa-mc1.dtb' commandline: console=ttySTM0,115200n8 Starting kernel at 0xc2ec3000, initrd at 0xc391e000, oftree at 0xc4880000... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.153-cip19-rt8 (KernelCI@build-j483928-arm-gcc-10-multi-v7-defconfig-preempt-rt-2scnc) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT_RT Wed Nov 9 21:45:48 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Linux Automation MC-1 board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created DMA memory pool at 0x10000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node mcuram2@10000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x10040000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vdev0vring0@10040000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x10041000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vdev0vring1@10041000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x10042000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vdev0buffer@10042000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x30000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node mcuram@30000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x38000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node retram@38000000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 64 MiB at 0xdc000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00000000c0000000-0x00000000dfffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000c0000000-0x00000000dfffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000c0000000-0x00000000dfffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 16 pages/cpu s34912 r8192 d22432 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttySTM0,115200n8 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 412572K/524288K available (14336K kernel code, 2355K rwdata, 5372K rodata, 2048K init, 420K bss, 46180K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms. [ 0.000000] rcu: RCU_SOFTIRQ processing moved to rcuc kthreads. [ 0.000000] No expedited grace period (rcu_normal_after_boot). [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. Starting syslogd: OK Starting k[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 logd: OK Running sysctl: [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000021] Switching to timer-based delay loop, resolution 41ns [ 0.012154] Console: colour dummy device 80x30 [ 0.012232] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.012256] pid_max: default: 32768 minimum: 301 [ 0.012492] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.012516] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.013683] CPU: Testing write buffer coherency: ok [ 0.014188] CPU0: update cpu_capacity 1024 [ 0.014208] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.015604] Setting up static identity map for 0xc0300000 - 0xc03000ac [ 0.019204] rcu: Hierarchical SRCU implementation. [ 0.027792] EFI services will not be available. [ 0.028361] smp: Bringing up secondary CPUs ... [ 0.030051] CPU1: update cpu_capacity 1024 [ 0.030071] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.030340] smp: Brought up 1 node, 2 CPUs [ 0.030359] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.030371] CPU: All CPU(s) started in SVC mode. [ 0.031333] devtmpfs: initialized [ 0.059650] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 OK Populating /dev using udev: [ 0.060091] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.060131] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.063421] pinctrl core: initialized pinctrl subsystem [ 0.067450] DMI not present or invalid. [ 0.068809] NET: Registered protocol family 16 [ 0.074639] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.080341] thermal_sys: Registered thermal governor 'step_wise' [ 0.080895] cpuidle: using governor menu [ 0.081232] No ATAGs? [ 0.081342] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.081360] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.087620] Serial: AMBA PL011 UART driver [ 0.139010] /soc/interrupt-controller@5000d000: bank0 [ 0.139058] /soc/interrupt-controller@5000d000: bank1 [ 0.139082] /soc/interrupt-controller@5000d000: bank2 [ 0.144026] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOA bank added [ 0.144743] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOB bank added [ 0.145390] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOC bank added [ 0.146062] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOD bank added [ 0.146707] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOE bank added [ 0.147370] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOF bank added [ 0.148013] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOG bank added [ 0.148685] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOH bank added [ 0.149312] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOI bank added [ 0.149531] stm32mp157-pinctrl soc:pin-controller@50002000: Pinctrl STM32 initialized [ 0.152026] stm32mp157-pinctrl soc:pin-controller-z@54004000: GPIOZ bank added [ 0.152057] stm32mp157-pinctrl soc:pin-controller-z@54004000: Pinctrl STM32 initialized [ 0.192046] iommu: Default domain type: Translated [ 0.192509] vgaarb: loaded [ 0.193889] SCSI subsystem initialized [ 0.194917] usbcore: registered new interface driver usbfs [ 0.195030] usbcore: registered new interface driver hub [ 0.195122] usbcore: registered new device driver usb [ 0.196895] pps_core: LinuxPPS API ver. 1 registered [ 0.196907] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.196942] PTP clock support registered [ 0.201716] clocksource: Switched to clocksource arch_sys_counter [ 1.599115] NET: Registered protocol family 2 [ 1.599525] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.601486] tcp_listen_portaddr_hash hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.601549] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 1.601631] TCP bind hash table entries: 4096 (order: 4, 114688 bytes, linear) [ 1.601931] TCP: Hash tables configured (established 4096 bind 4096) [ 1.602148] UDP hash table entries: 256 (order: 2, 16384 bytes, linear) [ 1.602213] UDP-Lite hash table entries: 256 (order: 2, 16384 bytes, linear) [ 1.602601] NET: Registered protocol family 1 [ 1.603758] RPC: Registered named UNIX socket transport module. [ 1.603779] RPC: Registered udp transport module. [ 1.603786] RPC: Registered tcp transport module. [ 1.603792] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.603807] PCI: CLS 0 bytes, default 64 [ 1.604497] Trying to unpack rootfs image as initramfs... [ 3.479299] Freeing initrd memory: 15752K [ 3.480202] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 3.482886] Initialise system trusted keyrings [ 3.483407] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 3.498687] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 3.500546] NFS: Registering the id_resolver key type [ 3.500655] Key type id_resolver registered [ 3.500664] Key type id_legacy registered [ 3.500866] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 3.500877] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 3.500945] ntfs: driver 2.1.32 [Flags: R/O]. [ 3.502012] Key type asymmetric registered [ 3.502028] Asymmetric key parser 'x509' registered [ 3.502106] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 3.502120] io scheduler mq-deadline registered [ 3.502129] io scheduler kyber registered [ 3.544198] reg11: supplied by regulator-dummy [ 3.544643] reg18: supplied by regulator-dummy [ 3.545113] usb33: supplied by regulator-dummy [ 3.649387] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 3.655700] SuperH (H)SCI(F) driver initialized [ 3.656973] msm_serial: driver initialized [ 3.657212] STMicroelectronics ASC driver initialized [ 3.659638] STM32 USART driver initialized [ 3.660262] stm32-usart 40010000.serial: rx dma alloc failed [ 3.660280] stm32-usart 40010000.serial: interrupt mode used for rx (no dma) [ 3.660293] stm32-usart 40010000.serial: tx dma alloc failed [ 3.660302] stm32-usart 40010000.serial: interrupt mode used for tx (no dma) [ 3.660333] 40010000.serial: ttySTM0 at MMIO 0x40010000 (irq = 30, base_baud = 4000000) is a stm32-usart [ 3.660512] printk: console [ttySTM0] enabled [ 3.672055] panel-simple panel: Specify missing connector_type [ 3.680681] random: crng init done [ 3.691960] brd: module loaded [ 3.709999] loop: module loaded [ 3.728829] CAN device driver interface [ 3.729948] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 3.731262] e1000e: Intel(R) PRO/1000 Network Driver [ 3.731271] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.731391] igb: Intel(R) Gigabit Ethernet Network Driver [ 3.731399] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.736172] stm32-dwmac 5800a000.ethernet: IRQ eth_wake_irq not found [ 3.736196] stm32-dwmac 5800a000.ethernet: IRQ eth_lpi not found [ 3.736408] stm32-dwmac 5800a000.ethernet: PTP uses main clock [ 3.736426] stm32-dwmac 5800a000.ethernet: no reset control found [ 3.737117] stm32-dwmac 5800a000.ethernet: User ID: 0x40, Synopsys ID: 0x42 [ 3.737163] stm32-dwmac 5800a000.ethernet: DWMAC4/5 [ 3.737178] stm32-dwmac 5800a000.ethernet: DMA HW capability register supported [ 3.737190] stm32-dwmac 5800a000.ethernet: RX Checksum Offload Engine supported [ 3.737199] stm32-dwmac 5800a000.ethernet: TX Checksum insertion supported [ 3.737208] stm32-dwmac 5800a000.ethernet: Wake-Up On Lan supported [ 3.737351] stm32-dwmac 5800a000.ethernet: TSO supported [ 3.737361] stm32-dwmac 5800a000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 3.737375] stm32-dwmac 5800a000.ethernet: Enabled Flow TC (entries=2) [ 3.737386] stm32-dwmac 5800a000.ethernet: TSO feature enabled [ 3.737398] stm32-dwmac 5800a000.ethernet: Using 32 bits DMA width [ 3.809981] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 3.810093] usbcore: registered new interface driver pegasus [ 3.810187] usbcore: registered new interface driver asix [ 3.810254] usbcore: registered new interface driver ax88179_178a [ 3.810319] usbcore: registered new interface driver cdc_ether [ 3.810431] usbcore: registered new interface driver smsc75xx [ 3.810523] usbcore: registered new interface driver smsc95xx [ 3.810591] usbcore: registered new interface driver net1080 [ 3.810657] usbcore: registered new interface driver cdc_subset [ 3.810724] usbcore: registered new interface driver zaurus [ 3.810842] usbcore: registered new interface driver cdc_ncm [ 3.814715] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.814732] ehci-pci: EHCI PCI platform driver [ 3.814803] ehci-platform: EHCI generic platform driver [ 3.815056] ehci-orion: EHCI orion driver [ 3.815265] SPEAr-ehci: EHCI SPEAr driver [ 3.815456] ehci-st: EHCI STMicroelectronics driver [ 3.815646] ehci-exynos: EHCI Exynos driver [ 3.815871] ehci-atmel: EHCI Atmel driver [ 3.816060] tegra-ehci: Tegra EHCI driver [ 3.816264] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.816320] ohci-pci: OHCI PCI platform driver [ 3.816410] ohci-platform: OHCI generic platform driver [ 3.816655] SPEAr-ohci: OHCI SPEAr driver [ 3.816857] ohci-st: OHCI STMicroelectronics driver [ 3.817049] ohci-atmel: OHCI Atmel driver [ 3.818069] usbcore: registered new interface driver usb-storage [ 3.826009] i2c /dev entries driver [ 3.854520] stm32f7-i2c 40015000.i2c: STM32F7 I2C-0 bus adapter [ 3.880994] stpmic1 1-0033: PMIC Chip Version: 0x10 [ 3.886107] vddcore: supplied by regulator-dummy [ 3.889422] vdd_ddr: supplied by regulator-dummy [ 3.892672] vdd: supplied by regulator-dummy [ 3.895938] v3v3: supplied by 5V2 [ 3.898966] v1v8_audio: supplied by v3v3 [ 3.903054] v3v3_hdmi: supplied by 5V2 [ 3.906793] vtt_ddr: supplied by regulator-dummy [ 3.909944] vdd_usb: supplied by regulator-dummy [ 3.910744] vdda: supplied by 5V2 [ 3.914185] v1v2_hdmi: supplied by v3v3 [ 3.917567] vref_ddr: supplied by regulator-dummy [ 3.920831] bst_out: supplied by 5V2 [ 3.922052] vbus_otg: supplied by bst_out [ 3.923048] vbus_sw: supplied by bst_out [ 3.928635] input: pmic_onkey as /devices/platform/soc/5c002000.i2c/i2c-1/1-0033/5c002000.i2c:stpmic@33:onkey/input/input0 [ 3.931607] at24 1-0050: 4096 byte 24c32 EEPROM, writable, 1 bytes/write [ 3.932208] stm32f7-i2c 5c002000.i2c: STM32F7 I2C-1 bus adapter [ 3.951459] mmci-pl18x 58005000.sdmmc: Got CD GPIO [ 3.952885] mmci-pl18x 58005000.sdmmc: mmc0: PL180 manf 53 rev1 at 0x58005000 irq 52,0 (pio) [ 3.984553] mmci-pl18x 58007000.sdmmc: mmc1: PL180 manf 53 rev1 at 0x58007000 irq 53,0 (pio) [ 4.011425] sdhci: Secure Digital Host Controller Interface driver [ 4.011438] sdhci: Copyright(c) Pierre Ossman [ 4.017345] Synopsys Designware Multimedia Card Interface Driver [ 4.021015] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.026228] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 4.027149] usbcore: registered new interface driver usbhid [ 4.027163] usbhid: USB HID core driver [ 4.037073] NET: Registered protocol family 10 [ 4.040016] Segment Routing with IPv6 [ 4.040139] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.041327] NET: Registered protocol family 17 [ 4.041369] can: controller area network core [ 4.041529] NET: Registered protocol family 29 [ 4.041543] can: raw protocol [ 4.041556] can: broadcast manager protocol [ 4.041577] can: netlink gateway - max_hops=1 [ 4.042723] Key type dns_resolver registered [ 4.042830] ThumbEE CPU extension supported. [ 4.042858] Registering SWP/SWPB emulation handler [ 4.043582] printk: console [ttySTM0]: printing thread started [ 4.043648] Loading compiled-in X.509 certificates [ 4.099438] stm32-dma 48000000.dma-controller: STM32 DMA driver registered [ 4.105369] stm32-dma 48001000.dma-controller: STM32 DMA driver registered [ 4.111419] stm32-mdma 58000000.dma-controller: STM32 MDMA driver registered [ 4.118956] panel-simple panel: Specify missing connector_type [ 4.131551] panel-simple panel: Specify missing connector_type [ 4.176664] Freeing unused kernel memory: 2048K [ 4.180448] Run /init as init process [ 4.203724] mmc1: new DDR MMC card at address 0001 [ 4.217373] mmcblk1: mmc1:0001 Q2J55L 7.09 GiB [ 4.217702] mmcblk1boot0: mmc1:0001 Q2J55L partition 1 16.0 MiB [ 4.218003] mmcblk1boot1: mmc1:0001 Q2J55L partition 2 16.0 MiB [ 4.219075] mmcblk1rpmb: mmc1:0001 Q2J55L partition 3 4.00 MiB, chardev (235:0) [ 4.354316] mmcblk1: p1 p2 p3 p4 [ 4.454987] panel-simple panel: Specify missing connector_type [ 4.499959] udevd[128]: starting version 3.2.9 [ 4.517781] udevd[128]: specified user 'tss' unknown [ 4.518050] udevd[128]: specified group 'tss' unknown [ 4.537915] udevd[129]: starting eudev-3.2.9 [ 6.750300] panel-simple panel: Specify missing connector_type [ 7.037175] panel-simple panel: Specify missing connector_type [ 7.141292] etnaviv etnaviv: bound 59000000.gpu (ops gpu_ops [etnaviv]) [ 7.141462] etnaviv-gpu 59000000.gpu: model: GC400, revision: 4652 [ 7.143301] etnaviv-gpu 59000000.gpu: Need to move linear window on MC1.0, disabling TS [ 7.157737] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 [ 7.165439] panel-simple panel: Specify missing connector_type [ 7.232688] panel-simple panel: Specify missing connector_type [ 8.454115] panel-simple panel: Specify missing connector_type [ 8.474363] [drm] Initialized stm 1.0.0 20170330 for 5a001000.display-controller on minor 1 [ 8.516601] Console: switching to colour frame buffer device 100x30 [ 8.540844] stm32-display 5a001000.display-controller: [drm] fb0: stmdrmfb frame buffer device done Saving random seed: OK Starting network: OK Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-823140/environment . /lava-823140/environment / # /lava-823140/bin/lava-test-runner /lava-823140/0 /lava-823140/bin/lava-test-runner /lava-823140/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-823140/0/tests/0_dmesg + cat uuid + UUID=823140_1.5.2.3.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 9.376331] [ 9.436722] [ 9.488804] + set +x [ 9.548305] [ 9.550586] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-823140/environment / # . /lava-823140/environment/lava-823140/bin/lava-test-runner /lava-823140/1 [ 9.830418] BUG: scheduling while atomic: swapper/0/0/0x00010002 [ 9.830456] Modules linked in: pwm_stm32 stm_drm etnaviv gpu_sched stm32_timers [ 9.830494] Preemption disabled at: [ 9.830498] [] schedule_preempt_disabled+0x1c/0x20 [ 9.830532] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.10.153-cip19-rt8 #1 [ 9.830547] Hardware name: STM32 (Device Tree Support) [ 9.830567] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [ 9.830600] [] (show_stack) from [] (dump_stack+0xb4/0xc8) [ 9.830627] [] (dump_stack) from [] (__schedule_bug+0xbc/0xd0) [ 9.830655] [] (__schedule_bug) from [] (__schedule+0x4e0/0x788) [ 9.830679] [] (__schedule) from [] (preempt_schedule_lock+0x28/0x4c) [ 9.830702] [] (preempt_schedule_lock) from [] (rt_spin_lock_slowlock_locked+0x11c/0x300) [ 9.830728] [] (rt_spin_lock_slowlock_locked) from [] (rt_spin_lock_slowlock+0x54/0x7c) [ 9.830755] [] (rt_spin_lock_slowlock) from [] (rt_spin_lock+0x50/0x5c) [ 9.830782] [] (rt_spin_lock) from [] (stm32_usart_interrupt+0x11c/0x130) [ 9.830816] [] (stm32_usart_interrupt) from [] (__handle_irq_event_percpu+0x5c/0x27c) [ 9.830848] [] (__handle_irq_event_percpu) from [] (handle_irq_event+0x80/0x108) [ 9.830873] [] (handle_irq_event) from [] (handle_fasteoi_irq+0xb0/0x1e0) [ 9.830902] [] (handle_fasteoi_irq) from [] (__handle_domain_irq+0xa0/0x10c) [ 9.830928] [] (__handle_domain_irq) from [] (gic_handle_irq+0x94/0xb4) [ 9.830959] [] (gic_handle_irq) from [] (__irq_svc+0x6c/0xbc) [ 9.830984] Exception stack(0xc1901f08 to 0xc1901f50) [ 9.831000] 1f00: 00000000 00004e48 dbb904c8 c031c9c0 ffffe000 c1b3e2e0 [ 9.831016] 1f20: c1907514 c1907558 00000000 c1900000 00000000 c1901f70 00000001 c1901f58 [ 9.831027] 1f40: c03080c4 c03080c8 60000113 ffffffff [ 9.831036] [] (__irq_svc) from [] (arch_cpu_idle+0x38/0x3c) [ 9.831063] [] (arch_cpu_idle) from [] (default_idle_call+0x50/0x1bc) [ 9.831091] [] (default_idle_call) from [] (do_idle+0x270/0x308) [ 9.831123] [] (do_idle) from [] (cpu_startup_entry+0x18/0x1c) [ 9.831152] [] (cpu_startup_entry) from [] (start_kernel+0x4e0/0x518) [ 9.831231] ------------[ cut here ]------------ [ 9.831241] WARNING: CPU: 0 PID: 0 at kernel/sched/core.c:4865 preempt_count_sub+0xa0/0x100 [ 9.831268] DEBUG_LOCKS_WARN_ON(val > preempt_count()) [ 9.831274] Modules linked in: pwm_stm32 stm_drm etnaviv gpu_sched stm32_timers [ 9.831306] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.10.153-cip19-rt8 #1 [ 9.831320] Hardware name: STM32 (Device Tree Support) [ 9.831329] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [ 9.831358] [] (show_stack) from [] (dump_stack+0xb4/0xc8) [ 9.831382] [] (dump_stack) from [] (__warn+0xec/0x104) [ 9.831407] [] (__warn) from [] (warn_slowpath_fmt+0x98/0xbc) [ 9.831431] [] (warn_slowpath_fmt) from [] (preempt_count_sub+0xa0/0x100) [ 9.831455] [] (preempt_count_sub) from [] (irq_exit+0xc/0x15c) [ 9.831483] [] (irq_exit) from [] (__handle_domain_irq+0xa4/0x10c) [ 9.831509] [] (__handle_domain_irq) from [] (gic_handle_irq+0x94/0xb4) [ 9.831537] [] (gic_handle_irq) from [] (__irq_svc+0x6c/0xbc) [ 9.831561] Exception stack(0xc1901f08 to 0xc1901f50) [ 9.831577] 1f00: 00000000 00004e48 dbb904c8 c031c9c0 ffffe000 c1b3e2e0 [ 9.831592] 1f20: c1907514 c1907558 00000000 c1900000 00000000 c1901f70 00000001 c1901f58 [ 9.831604] 1f40: c03080c4 c03080c8 60000113 ffffffff [ 9.831612] [] (__irq_svc) from [] (arch_cpu_idle+0x38/0x3c) [ 9.831639] [] (arch_cpu_idle) from [] (default_idle_call+0x50/0x1bc) [ 9.831668] [] (default_idle_call) from [] (do_idle+0x270/0x308) [ 9.831697] [] (do_idle) from [] (cpu_startup_entry+0x18/0x1c) [ 9.831726] [] (cpu_startup_entry) from [] (start_kernel+0x4e0/0x518) [ 9.831757] ---[ end trace 0000000000000002 ]--- [ 10.832121] ttySTM ttySTM0: 1 input overrun(s) / # /lava-823140/bin[ 34.411802] reg11: disabling [ 34.411836] reg18: disabling [ 34.412058] vdd_usb: disabling [ 34.412188] vdda: disabling