[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 7923192/tftp-deploy-v6bzn3xz/kernel/zImage tftp 0x10000000 7923192/tftp-deploy-v6bzn3xz/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '7923192/tftp-deploy-v6bzn3xz/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 11.6 MiB/s done Bytes transferred = 9679360 (93b200 hex) => tftp 0x14000000 7923192/tftp-deploy-v6bzn3xz/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 7923192/tftp-deploy-v6bzn3xz/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '7923192/tftp-deploy-v6bzn3xz/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 11.6 MiB/s done Bytes transferred = 16069741 (f5346d hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 7923192/tftp-deploy-v6bzn3xz/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 7923192/tftp-deploy-v6bzn3xz/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '7923192/tftp-deploy-v6bzn3xz/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x93b200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16069677 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.153-cip19-rt8 (KernelCI@build-j483909-arm-gcc-10-multi-v7-defconfig-xkp49) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Nov 9 22:00:51 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 16 pages/cpu s33612 r8192 d23732 u65536 [ 0.000000] pcpu-alloc: s33612 r8192 d23732 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933672K/1048576K available (13312K kernel code, 2324K rwdata, 5344K rodata, 2048K init, 417K bss, 49368K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008439] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022243] Console: colour dummy device 80x30 <6>[ 0.024135] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034547] pid_max: default: 32768 minimum: 301 <6>[ 0.039574] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046998] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055625] CPU: Testing write buffer coherency: ok <6>[ 0.060116] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065671] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072023] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079744] rcu: Hierarchical SRCU implementation. <6>[ 0.086787] EFI services will not be available. <6>[ 0.089018] smp: Bringing up secondary CPUs ... <6>[ 0.094299] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.099426] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105644] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.110650] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116851] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.121873] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127301] smp: Brought up 1 node, 4 CPUs <6>[ 0.131529] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137989] CPU: All CPU(s) started in SVC mode. <6>[ 0.143398] devtmpfs: initialized <6>[ 0.153632] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158971] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168843] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179055] pinctrl core: initialized pinctrl subsystem <6>[ 0.183487] DMI not present or invalid. <6>[ 0.186645] NET: Registered protocol family 16 <6>[ 0.194021] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200614] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200792] cpuidle: using governor menu <6>[ 0.208929] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.391067] vdd1p1: supplied by regulator-dummy <6>[ 0.400290] vdd3p0: supplied by regulator-dummy <6>[ 0.409480] vdd2p5: supplied by regulator-dummy <6>[ 0.418671] vddarm: supplied by regulator-dummy <6>[ 0.428040] vddpu: supplied by regulator-dummy <6>[ 0.436989] vddsoc: supplied by regulator-dummy <6>[ 0.771276] No ATAGs? <6>[ 0.771458] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.779239] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.789388] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.799649] Serial: AMBA PL011 UART driver <6>[ 0.803298] printk: console [ramoops-1] enabled <6>[ 0.806162] pstore: Registered ramoops as persistent store backend <6>[ 0.812373] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.850036] iommu: Default domain type: Translated <6>[ 0.852746] vgaarb: loaded <5>[ 0.856219] SCSI subsystem initialized <7>[ 0.859624] libata version 3.00 loaded. <6>[ 0.863611] usbcore: registered new interface driver usbfs <6>[ 0.869198] usbcore: registered new interface driver hub <6>[ 0.874725] usbcore: registered new device driver usb <6>[ 0.881538] i2c i2c-0: IMX I2C adapter registered <6>[ 0.886362] i2c i2c-1: IMX I2C adapter registered <6>[ 0.890736] i2c i2c-2: IMX I2C adapter registered <6>[ 0.896264] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.900092] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.909524] PTP clock support registered <6>[ 0.917191] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.056544] NET: Registered protocol family 2 <6>[ 2.058772] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.067171] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.074615] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.082686] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.090151] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.096798] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.103522] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.110979] NET: Registered protocol family 1 <6>[ 2.115980] RPC: Registered named UNIX socket transport module. <6>[ 2.121599] RPC: Registered udp transport module. <6>[ 2.126523] RPC: Registered tcp transport module. <6>[ 2.131502] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.138205] PCI: CLS 0 bytes, default 64 <6>[ 2.142872] Trying to unpack rootfs image as initramfs... <6>[ 3.502620] Freeing initrd memory: 15696K <4>[ 3.504473] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.511870] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.521665] Initialise system trusted keyrings <6>[ 3.524796] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.536924] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.540931] NFS: Registering the id_resolver key type <5>[ 3.545506] Key type id_resolver registered <5>[ 3.549933] Key type id_legacy registered <6>[ 3.554261] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.561154] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.568835] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.573873] Key type asymmetric registered <5>[ 3.577778] Asymmetric key parser 'x509' registered <6>[ 3.582930] bounce: pool size: 64 pages <6>[ 3.587006] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.594648] io scheduler mq-deadline registered <6>[ 3.599431] io scheduler kyber registered <6>[ 3.642925] mxs-dma 110000.dma-apbh: initialized <4>[ 3.649710] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.656619] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.720397] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.728628] SuperH (H)SCI(F) driver initialized <6>[ 3.731568] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.740448] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.748415] printk: console [ttymxc1] enabled <6>[ 3.752918] printk: bootconsole [ec_imx21] disabled <6>[ 3.748415] printk: console [ttymxc1] enabled <6>[ 3.752918] printk: bootconsole [ec_imx21] disabled <6>[ 3.759503] msm_serial: driver initialized <6>[ 3.759756] STMicroelectronics ASC driver initialized <6>[ 3.761719] STM32 USART driver initialized <4>[ 3.772848] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.773000] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.773538] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.782364] brd: module loaded <6>[ 3.792354] loop: module loaded <6>[ 3.796233] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.796248] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.796258] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.796266] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.796348] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.796505] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.796590] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.799430] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.799458] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.799476] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.800992] scsi host0: ahci-imx <6>[ 3.801355] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.813698] CAN device driver interface <6>[ 3.815021] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.818573] pps pps0: new PPS source ptp0 <6>[ 3.851849] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.853363] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.853368] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.853426] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.853432] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.859611] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.859657] usbcore: registered new interface driver pegasus <6>[ 3.859697] usbcore: registered new interface driver asix <6>[ 3.859733] usbcore: registered new interface driver ax88179_178a <6>[ 3.859764] usbcore: registered new interface driver cdc_ether <6>[ 3.859807] usbcore: registered new interface driver smsc75xx <6>[ 3.859857] usbcore: registered new interface driver smsc95xx <6>[ 3.859890] usbcore: registered new interface driver net1080 <6>[ 3.859923] usbcore: registered new interface driver cdc_subset <6>[ 3.859953] usbcore: registered new interface driver zaurus <6>[ 3.860020] usbcore: registered new interface driver cdc_ncm <6>[ 3.863569] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.863575] ehci-pci: EHCI PCI platform driver <6>[ 3.863610] ehci-platform: EHCI generic platform driver <6>[ 3.863905] ehci-orion: EHCI orion driver <6>[ 3.864123] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.864304] ehci-st: EHCI STMicroelectronics driver <6>[ 3.864487] ehci-exynos: EHCI Exynos driver <6>[ 3.864663] ehci-atmel: EHCI Atmel driver <6>[ 3.864839] tegra-ehci: Tegra EHCI driver <6>[ 3.865050] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.865068] ohci-pci: OHCI PCI platform driver <6>[ 3.865119] ohci-platform: OHCI generic platform driver <6>[ 3.865392] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.865580] ohci-st: OHCI STMicroelectronics driver <6>[ 3.865763] ohci-atmel: OHCI Atmel driver <6>[ 3.866807] usbcore: registered new interface driver usb-storage <6>[ 3.874964] i2c /dev entries driver <6>[ 3.894483] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.894490] sdhci: Copyright(c) Pierre Ossman <6>[ 3.897269] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.899261] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.900585] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.900629] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.901766] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.904350] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.905388] usbcore: registered new interface driver usbhid <6>[ 3.905395] usbhid: USB HID core driver <6>[ 3.911963] NET: Registered protocol family 10 <6>[ 3.912966] Segment Routing with IPv6 <6>[ 3.913040] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.913597] NET: Registered protocol family 17 <6>[ 3.913613] can: controller area network core <6>[ 3.913688] NET: Registered protocol family 29 <6>[ 3.913695] can: raw protocol <6>[ 3.913702] can: broadcast manager protocol <6>[ 3.913711] can: netlink gateway - max_hops=1 <5>[ 3.914085] Key type dns_resolver registered <6>[ 3.916135] ThumbEE CPU extension supported. <5>[ 3.916150] Registering SWP/SWPB emulation handler <6>[ 3.916901] printk: console [ttymxc1]: printing thread started <6>[ 3.917084] printk: console [ramoops-1]: printing thread started <5>[ 3.917106] Loading compiled-in X.509 certificates <6>[ 3.922186] pstore: Using crash dump compression: deflate <6>[ 3.936171] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <4>[ 3.943872] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.944003] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.945446] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.949343] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <4>[ 3.953921] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.957206] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.957230] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.971679] mmc2: new high speed SDHC card at address 0001 <6>[ 3.972456] mmcblk2: mmc2:0001 SD 14.6 GiB <4>[ 3.985267] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.985274] GPT:29296874 != 30560255 <4>[ 3.985279] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.985282] GPT:29296874 != 30560255 <4>[ 3.985286] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.985322] mmcblk2: p1 p2 p3 <6>[ 3.987192] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.987781] hub 1-0:1.0: USB hub found <6>[ 3.987819] hub 1-0:1.0: 1 port detected <6>[ 3.990022] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 3.994310] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.994438] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.995803] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.000020] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.000148] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.001488] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.003350] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.008726] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.008850] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.010230] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.143832] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.143877] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.143884] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.156226] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.287161] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.508137] hub 1-1:1.0: USB hub found <6>[ 4.508279] hub 1-1:1.0: 3 ports detected <4>[ 4.513235] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.513356] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.514729] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.837247] usb 1-1.1: new low-speed USB device number 3 using ci_hdrc <6>[ 5.006787] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint as /devices/platform/soc/2100000.bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-1.1:1.0/0003:17EF:6009.0001/input/input1 <6>[ 5.067946] hid-generic 0003:17EF:6009.0001: input: USB HID v1.10 Keyboard [Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint] on usb-ci_hdrc.1-1.1/input0 <4>[ 5.077127] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.077566] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.080854] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 5.097598] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint Mouse as /devices/platform/soc/2100000.bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-1.1:1.1/0003:17EF:6009.0002/input/input2 <6>[ 5.100736] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint System Control as /devices/platform/soc/2100000.bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-1.1:1.1/0003:17EF:6009.0002/input/input3 <6>[ 5.167405] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint Consumer Control as /devices/platform/soc/2100000.bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-1.1:1.1/0003:17EF:6009.0002/input/input4 <6>[ 5.167580] hid-generic 0003:17EF:6009.0002: input: USB HID v1.10 Mouse [Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint] on usb-ci_hdrc.1-1.1/input1 <4>[ 5.176586] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.176878] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.180239] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.277706] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.287305] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.317174] Sending DHCP requests ., OK <6>[ 7.357263] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 <6>[ 7.357287] IP-Config: Complete: <6>[ 7.357293] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.357320] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) <6>[ 7.357332] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.357348] nameserver0=192.168.201.1 <6>[ 7.365665] Freeing unused kernel memory: 2048K <6>[ 7.438226] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.567987] udevd[138]: starting version 3.2.9 <5>[ 7.568938] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.569246] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.569366] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.587952] udevd[138]: specified user 'tss' unknown <27>[ 7.588075] udevd[138]: specified group 'tss' unknown <30>[ 7.590340] udevd[139]: starting eudev-3.2.9 <6>[ 7.994320] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 7.996293] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.001137] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.001285] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.002757] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.021611] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.021792] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.023477] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.034959] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.035189] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.037728] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.074421] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.074599] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.076189] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.175922] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.176104] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.178042] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.197875] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.199264] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.199623] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.199709] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.199949] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.200016] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.200030] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.200393] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <4>[ 8.205485] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.205636] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.207233] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.271046] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.271162] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.271271] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.271374] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.276814] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.276957] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.278888] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.302470] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.302537] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.302605] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.302652] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.312422] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.312684] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.315866] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.319667] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.319726] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.319785] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.319828] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.442840] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.503640] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.564401] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.564420] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.564429] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 8.573800] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.573946] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.575495] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.579442] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.579507] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.579562] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.579605] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.689802] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.689963] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.691784] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.704361] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.726119] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 8.737702] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.737909] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.738085] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.738235] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.738901] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.738963] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.739028] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.739088] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.745598] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.745936] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.748028] panel-simple panel-lvds0: supply power not found, using dummy regulator <27>[ 8.772398] udevd[143]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90010, key code 190): Invalid argument <27>[ 8.772447] udevd[143]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90011, key code 148): Invalid argument <27>[ 8.772481] udevd[143]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90012, key code 152): Invalid argument <27>[ 8.772507] udevd[143]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90013, key code 236): Invalid argument <27>[ 8.772533] udevd[143]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90014, key code 238): Invalid argument <27>[ 8.772557] udevd[143]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90015, key code 212): Invalid argument <27>[ 8.772581] udevd[143]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90016, key code 227): Invalid argument <6>[ 8.773984] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.774055] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.774120] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.774173] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.802255] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.802427] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.805474] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.818041] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.818111] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.818194] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) done <6>[ 8.818247] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.117986] caam algorithms registered in /proc/crypto Saving random seed: <6>[ 9.119401] caam 2100000.crypto: registering rng-caam <4>[ 9.124518] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.124678] panel-simple panel-lcd: Specify missing connector_type OK <4>[ 9.126288] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.177493] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) Starting network: <6>[ 9.177563] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.177622] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.177667] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.182337] panel-simple panel-lcd: supply power not found, using dummy regulator ip: RTNETLINK answers: File exist<4>[ 9.182478] panel-simple panel-lcd: Specify missing connector_type s <4>[ 9.184214] panel-simple panel-lvds0: supply power not found, using dummy regulator FAIL <6>[ 9.188459] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.188572] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.188666] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.188757] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Starting dropbear sshd: <5>[ 9.194915] random: dd: uninitialized urandom read (32 bytes read) <5>[ 9.307909] random: crng init done OK <5>[ 9.307920] random: 1 urandom warning(s) missed due to ratelimiting /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-7923192/environment . /lava-7923192/environment / # /lava-7923192/bin/lava-test-runner /lava-7923192/0 /lava-7923192/bin/lava-test-runner /lava-7923192/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-7923192/0/tests/0_dmesg + cat uuid + UUID=7923192_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.948439] <8>[ 9.996312] <8>[ 10.030331] + set +x / # <8>[ 10.069962] <8>[ 10.071199] # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-7923192/environment / # . /lava-7923192/environment/lava-7923192/bin/lava-test-runner /lava-7923192/1 / # /lava-7923192/bin/lava-test-runner /lava-7923192/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-7923192/1/tests/1_bootrr + cat uuid + UUID=7923192_1.5.2<8>[ 10.586371] .4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-7923192/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-7923192/1/../bin/lava-test-case <8>[ 11.643380] /lava-7923192/1/../bin/lava-test-case <8>[ 11.675419] /lava-7923192/1/../bin/lava-test-case <8>[ 11.696069] + set +x / # <8>[ 11.707725]