[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 7923202/tftp-deploy-8e3doh1w/kernel/zImage tftp 0x10000000 7923202/tftp-deploy-8e3doh1w/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '7923202/tftp-deploy-8e3doh1w/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 11.7 MiB/s done Bytes transferred = 9679360 (93b200 hex) => tftp 0x14000000 7923202/tftp-deploy-8e3doh1w/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 7923202/tftp-deploy-8e3doh1w/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '7923202/tftp-deploy-8e3doh1w/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 5.8 MiB/s done Bytes transferred = 12141188 (b94284 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 7923202/tftp-deploy-8e3doh1w/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 7923202/tftp-deploy-8e3doh1w/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '7923202/tftp-deploy-8e3doh1w/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.1 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/7923202/extract-nfsrootfs-v_cncebh,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/7923202/extract-nfsrootfs-v_cncebh,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x93b200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12141124 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.153-cip19-rt8 (KernelCI@build-j483909-arm-gcc-10-multi-v7-defconfig-xkp49) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Nov 9 22:00:51 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 16 pages/cpu s33612 r8192 d23732 u65536 [ 0.000000] pcpu-alloc: s33612 r8192 d23732 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/7923202/extract-nfsrootfs-v_cncebh,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 937508K/1048576K available (13312K kernel code, 2324K rwdata, 5344K rodata, 2048K init, 417K bss, 45532K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008438] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022270] Console: colour dummy device 80x30 <6>[ 0.024166] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034573] pid_max: default: 32768 minimum: 301 <6>[ 0.039602] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047025] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055655] CPU: Testing write buffer coherency: ok <6>[ 0.060141] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065703] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072056] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079781] rcu: Hierarchical SRCU implementation. <6>[ 0.086820] EFI services will not be available. <6>[ 0.089054] smp: Bringing up secondary CPUs ... <6>[ 0.094330] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.099460] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105692] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.110682] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116879] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.121905] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127333] smp: Brought up 1 node, 4 CPUs <6>[ 0.131561] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.138021] CPU: All CPU(s) started in SVC mode. <6>[ 0.143432] devtmpfs: initialized <6>[ 0.153682] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159012] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168891] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179104] pinctrl core: initialized pinctrl subsystem <6>[ 0.183539] DMI not present or invalid. <6>[ 0.186694] NET: Registered protocol family 16 <6>[ 0.193987] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200602] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200780] cpuidle: using governor menu <6>[ 0.208910] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.390991] vdd1p1: supplied by regulator-dummy <6>[ 0.400228] vdd3p0: supplied by regulator-dummy <6>[ 0.409415] vdd2p5: supplied by regulator-dummy <6>[ 0.418602] vddarm: supplied by regulator-dummy <6>[ 0.427951] vddpu: supplied by regulator-dummy <6>[ 0.436913] vddsoc: supplied by regulator-dummy <6>[ 0.771517] No ATAGs? <6>[ 0.771699] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.779478] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.789623] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.799852] Serial: AMBA PL011 UART driver <6>[ 0.803503] printk: console [ramoops-1] enabled <6>[ 0.806371] pstore: Registered ramoops as persistent store backend <6>[ 0.812577] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.850152] iommu: Default domain type: Translated <6>[ 0.852862] vgaarb: loaded <5>[ 0.856344] SCSI subsystem initialized <7>[ 0.859745] libata version 3.00 loaded. <6>[ 0.863723] usbcore: registered new interface driver usbfs <6>[ 0.869314] usbcore: registered new interface driver hub <6>[ 0.874840] usbcore: registered new device driver usb <6>[ 0.881664] i2c i2c-0: IMX I2C adapter registered <6>[ 0.886456] i2c i2c-1: IMX I2C adapter registered <6>[ 0.890848] i2c i2c-2: IMX I2C adapter registered <6>[ 0.896353] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.900206] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.909639] PTP clock support registered <6>[ 0.917290] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.055224] NET: Registered protocol family 2 <6>[ 2.057476] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.065803] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.073335] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.081362] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.088828] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.095488] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.102222] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.109652] NET: Registered protocol family 1 <6>[ 2.114670] RPC: Registered named UNIX socket transport module. <6>[ 2.120282] RPC: Registered udp transport module. <6>[ 2.125204] RPC: Registered tcp transport module. <6>[ 2.130184] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.136871] PCI: CLS 0 bytes, default 64 <6>[ 2.141572] Trying to unpack rootfs image as initramfs... <6>[ 3.112429] Freeing initrd memory: 11860K <4>[ 3.114439] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.121645] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.131450] Initialise system trusted keyrings <6>[ 3.134798] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.146778] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.150868] NFS: Registering the id_resolver key type <5>[ 3.155362] Key type id_resolver registered <5>[ 3.159804] Key type id_legacy registered <6>[ 3.164124] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.171074] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.178692] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.183742] Key type asymmetric registered <5>[ 3.187632] Asymmetric key parser 'x509' registered <6>[ 3.192780] bounce: pool size: 64 pages <6>[ 3.196859] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.204504] io scheduler mq-deadline registered <6>[ 3.209282] io scheduler kyber registered <6>[ 3.252569] mxs-dma 110000.dma-apbh: initialized <4>[ 3.259368] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.266277] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.324223] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.332344] SuperH (H)SCI(F) driver initialized <6>[ 3.335287] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.344176] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.352126] printk: console [ttymxc1] enabled <6>[ 3.356633] printk: bootconsole [ec_imx21] disabled <6>[ 3.352126] printk: console [ttymxc1] enabled <6>[ 3.356633] printk: bootconsole [ec_imx21] disabled <6>[ 3.363179] msm_serial: driver initialized <6>[ 3.363433] STMicroelectronics ASC driver initialized <6>[ 3.365380] STM32 USART driver initialized <4>[ 3.376414] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.376565] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.376900] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.385993] brd: module loaded <6>[ 3.395956] loop: module loaded <6>[ 3.399910] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.399926] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.399936] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.399944] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.400023] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.400181] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.400246] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.403097] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.403124] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.403142] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.404656] scsi host0: ahci-imx <6>[ 3.405024] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.417403] CAN device driver interface <6>[ 3.418747] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.422282] pps pps0: new PPS source ptp0 <6>[ 3.440961] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.442465] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.442470] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.442529] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.442534] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.448741] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.448787] usbcore: registered new interface driver pegasus <6>[ 3.448829] usbcore: registered new interface driver asix <6>[ 3.448864] usbcore: registered new interface driver ax88179_178a <6>[ 3.448895] usbcore: registered new interface driver cdc_ether <6>[ 3.448936] usbcore: registered new interface driver smsc75xx <6>[ 3.448986] usbcore: registered new interface driver smsc95xx <6>[ 3.449020] usbcore: registered new interface driver net1080 <6>[ 3.449051] usbcore: registered new interface driver cdc_subset <6>[ 3.449081] usbcore: registered new interface driver zaurus <6>[ 3.449145] usbcore: registered new interface driver cdc_ncm <6>[ 3.452725] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.452732] ehci-pci: EHCI PCI platform driver <6>[ 3.452765] ehci-platform: EHCI generic platform driver <6>[ 3.453051] ehci-orion: EHCI orion driver <6>[ 3.453265] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.453446] ehci-st: EHCI STMicroelectronics driver <6>[ 3.453631] ehci-exynos: EHCI Exynos driver <6>[ 3.453806] ehci-atmel: EHCI Atmel driver <6>[ 3.453982] tegra-ehci: Tegra EHCI driver <6>[ 3.454193] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.454212] ohci-pci: OHCI PCI platform driver <6>[ 3.454263] ohci-platform: OHCI generic platform driver <6>[ 3.454522] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.454712] ohci-st: OHCI STMicroelectronics driver <6>[ 3.454897] ohci-atmel: OHCI Atmel driver <6>[ 3.455960] usbcore: registered new interface driver usb-storage <6>[ 3.464105] i2c /dev entries driver <6>[ 3.483676] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.483682] sdhci: Copyright(c) Pierre Ossman <6>[ 3.486374] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.488385] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.489679] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.489722] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.490943] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.493528] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.494498] usbcore: registered new interface driver usbhid <6>[ 3.494505] usbhid: USB HID core driver <6>[ 3.501017] NET: Registered protocol family 10 <6>[ 3.502005] Segment Routing with IPv6 <6>[ 3.502078] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.502635] NET: Registered protocol family 17 <6>[ 3.502651] can: controller area network core <6>[ 3.502722] NET: Registered protocol family 29 <6>[ 3.502730] can: raw protocol <6>[ 3.502736] can: broadcast manager protocol <6>[ 3.502745] can: netlink gateway - max_hops=1 <5>[ 3.503118] Key type dns_resolver registered <6>[ 3.505181] ThumbEE CPU extension supported. <5>[ 3.505197] Registering SWP/SWPB emulation handler <6>[ 3.505937] printk: console [ttymxc1]: printing thread started <6>[ 3.506134] printk: console [ramoops-1]: printing thread started <5>[ 3.506157] Loading compiled-in X.509 certificates <6>[ 3.511253] pstore: Using crash dump compression: deflate <6>[ 3.522932] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.523430] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <4>[ 3.532769] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.532900] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.534320] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.542741] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.546273] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.546297] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.567299] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.567896] hub 1-0:1.0: USB hub found <6>[ 3.567932] hub 1-0:1.0: 1 port detected <6>[ 3.569929] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 3.574141] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.574272] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.575630] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.579906] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.580027] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.581377] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.583249] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 3.588652] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.588780] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.590185] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.710469] mmc2: new high speed SDHC card at address 59b4 <6>[ 3.711224] mmcblk2: mmc2:59b4 SD 14.7 GiB <6>[ 3.754041] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.754100] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.754106] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.766208] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <4>[ 3.826119] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.826125] GPT:29296874 != 30863359 <4>[ 3.826130] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.826133] GPT:29296874 != 30863359 <4>[ 3.826136] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.826175] mmcblk2: p1 p2 p3 <4>[ 3.831494] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.831631] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.833086] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.867275] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.125333] hub 1-1:1.0: USB hub found <6>[ 4.131715] hub 1-1:1.0: 3 ports detected <4>[ 4.173874] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.174011] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.175376] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.917791] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.927367] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.957338] Sending DHCP requests .., OK <6>[ 10.377362] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 <6>[ 10.377387] IP-Config: Complete: <6>[ 10.377393] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 <6>[ 10.377418] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) <6>[ 10.377430] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 10.377445] nameserver0=192.168.201.1 <6>[ 10.385482] Freeing unused kernel memory: 2048K <6>[ 10.437652] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 <6>[ 11.324666] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 11.327172] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 11.342415] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 11.342615] panel-simple panel-lcd: Specify missing connector_type <4>[ 11.344376] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 11.359043] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 11.359192] panel-simple panel-lcd: Specify missing connector_type <4>[ 11.360757] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 11.413525] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 11.413766] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 11.414017] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 11.414176] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 11.457780] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 11.458613] panel-simple panel-lcd: Specify missing connector_type <4>[ 11.460599] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 11.489580] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.490063] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.490378] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.490462] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 11.490726] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 11.490796] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 11.490808] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 11.491242] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 11.492228] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 11.492289] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 11.492343] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 11.492386] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 11.497483] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 11.497718] panel-simple panel-lcd: Specify missing connector_type <4>[ 11.500737] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 11.566220] caam 2100000.crypto: Entropy delay = 3200 <6>[ 11.626195] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 11.626266] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 11.626328] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 11.626372] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 11.627020] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 11.632721] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 11.632870] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 11.632990] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 11.633103] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 11.687784] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 11.687803] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 11.687812] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 11.725422] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 11.728718] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 11.728907] panel-simple panel-lcd: Specify missing connector_type <4>[ 11.731051] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 11.732689] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 11.757796] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 11.757886] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 11.757980] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 11.758050] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 11.783108] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 11.783289] panel-simple panel-lcd: Specify missing connector_type <4>[ 11.785680] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 11.796728] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 11.796809] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 11.796875] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 11.796930] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 12.138946] caam algorithms registered in /proc/crypto <6>[ 12.140328] caam 2100000.crypto: registering rng-caam <4>[ 12.145941] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 12.146117] panel-simple panel-lcd: Specify missing connector_type <4>[ 12.148003] panel-simple panel-lvds0: supply power not found, using dummy regulator Begin: Loading essential drivers <6>[ 12.158609] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) ... <6>[ 12.158675] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) done.<6>[ 12.158749] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) Begin: Running /scripts/init-pr<6>[ 12.158803] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) emount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... done. <5>[ 12.322899] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f1:10 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.34 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-4 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 13.566293] systemd[1]: System time before build time, advancing clock. <30>[ 13.622253] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 13.623009] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 13.690318] systemd[1]: Set hostname to . <30>[ 14.556132] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 14.558076] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 14.558099] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ OK ] Created slice<30>[ 14.558828] systemd[1]: Created slice system-getty.slice. system-getty.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 14.628783] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 14.658655] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice User and Session Slice. <30>[ 14.688612] systemd[1]: Created slice User and Session Slice. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 14.718280] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 14.747674] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Local Encrypted Volumes. <30>[ 14.778089] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 14.778698] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Paths. <30>[ 14.807810] systemd[1]: Reached target Paths. [ OK ] Reached target Remote File Systems. <30>[ 14.837541] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Slices. <30>[ 14.867698] systemd[1]: Reached target Slices. [ OK ] Reached target Swap. <30>[ 14.897763] systemd[1]: Reached target Swap. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 14.928579] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on <30>[ 14.992922] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. Journal Socket (/dev/log<30>[ 14.994738] systemd[1]: Listening on Journal Socket (/dev/log). ). [ OK ] Listening on Journal Socket. <30>[ 15.038147] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 15.069760] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on udev Control Socket. <30>[ 15.099570] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 15.128828] systemd[1]: Listening on udev Kernel Socket. Mounting Kernel<30>[ 15.158594] systemd[1]: Condition check resulted in Huge Pages File System being skipped. Debug File System... <30>[ 15.159520] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 15.165376] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Trace File System... <30>[ 15.199160] systemd[1]: Mounting Kernel Trace File System... Starting Create list of st…odes for the current kernel... <30>[ 15.238449] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Load K<30>[ 15.274849] systemd[1]: Starting Load Kernel Module configfs... ernel Module configfs... Starting Load K<30>[ 15.311143] systemd[1]: Starting Load Kernel Module drm... ernel Module drm... Starting Load Kernel Module fuse... <30>[ 15.342283] systemd[1]: Starting Load Kernel Module fuse... <30>[ 15.384412] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 15.391435] systemd[1]: Starting Journal Service... Starting Journal Service... Starting Load K<30>[ 15.436131] systemd[1]: Starting Load Kernel Modules... ernel Modules... Starting Remount Root and Kernel File Systems<30>[ 15.472620] systemd[1]: Starting Remount Root and Kernel File Systems... [0m... Starting Coldplug All udev Devices... <30>[ 15.520835] systemd[1]: Starting Coldplug All udev Devices... [ OK ] Mounted Kernel Debug File System[0<30>[ 15.552125] systemd[1]: Mounted Kernel Debug File System. m. [ OK ] Mounted [0;1<30>[ 15.588004] systemd[1]: Mounted Kernel Trace File System. ;39mKernel Trace File System. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 15.638553] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Load Kernel Module configfs. <30>[ 15.689178] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 15.689874] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Started [0;1<30>[ 15.717890] systemd[1]: Started Journal Service. ;39mJournal Service. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... Starting Create System Users... <46>[ 16.037480] systemd-journald[281]: Received client request to flush runtime journal. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.153-cip19-rt8 #1 SMP Wed Nov 9 22:00:51 UTC 2022 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/7923202/extract-nfsrootfs-v_cncebh' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/7923202/extract-nfsrootfs-v_cncebh' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-7923202/environment . /lava-7923202/environment / # /lava-7923202/bin/lava-test-runner /lava-7923202/0 /lava-7923202/bin/lava-test-runner /lava-7923202/0 + export TESTRUN_ID=0_dmesg + cd /lava-7923202/0/tests/0_dmesg + cat uuid + UUID=7923202_1.6.2.4.1 + set +x + KERNELCI_LAVA=y /<8>[ 29.714680] bin/sh /opt/kernelci/dmesg.sh <8>[ 29.827566] <8>[ 29.924065] + set +x <8>[ 30.015526] <8>[ 30.017481] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-7923202/environment / # . /lava-7923202/environment/lava-7923202/bin/lava-test-runner /lava-7923202/1 / # /lava-7923202/bin/lava-test-runner /lava-7923202/1 + export TESTRUN_ID=1_bootrr + cd /lava-7923202/1/tests/1_bootrr + cat uuid + UUID=7923202_1.6.2.4.5<8>[ 30.646962] + set +x + export PATH=/opt/bootrr/helpers:/lava-7923202/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr + sh helpers/bootrr-auto /lava-7923202/1/../bin/lava-test-case <8>[ 31.767802] + set +x / # <8>[ 31.800560]