[Enter `^Ec?' for help]  U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.101.99 (3 ms) => setenv serverip 192.168.101.1 setenv serverip 192.168.101.1 => tftp 0x10000000 8333591/tftp-deploy-naa4ycwi/kernel/zImage tftp 0x10000000 8333591/tftp-deploy-naa4ycwi/kernel/zImage Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.99 Filename '8333591/tftp-deploy-naa4ycwi/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 3 MiB/s done Bytes transferred = 9679360 (93b200 hex) => tftp 0x14000000 8333591/tftp-deploy-naa4ycwi/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 8333591/tftp-deploy-naa4ycwi/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.99 Filename '8333591/tftp-deploy-naa4ycwi/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################################################### 2.9 MiB/s done Bytes transferred = 16037729 (f4b761 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 8333591/tftp-deploy-naa4ycwi/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 8333591/tftp-deploy-naa4ycwi/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.99 Filename '8333591/tftp-deploy-naa4ycwi/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.5 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x93b200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16037665 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.158-cip22-rt9 (KernelCI@build-j681170-arm-gcc-10-defconfig-zlbwb) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sun Dec 11 18:46:11 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 16 pages/cpu s33612 r8192 d23732 u65536 [ 0.000000] pcpu-alloc: s33612 r8192 d23732 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933704K/1048576K available (13312K kernel code, 2324K rwdata, 5344K rodata, 2048K init, 417K bss, 49336K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008438] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022609] Console: colour dummy device 80x30 <6>[ 0.024500] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034912] pid_max: default: 32768 minimum: 301 <6>[ 0.039941] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047365] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055998] CPU: Testing write buffer coherency: ok <6>[ 0.060481] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.066041] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072385] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.080203] rcu: Hierarchical SRCU implementation. <6>[ 0.087399] EFI services will not be available. <6>[ 0.089629] smp: Bringing up secondary CPUs ... <6>[ 0.094920] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.100038] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.106282] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.111261] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.117443] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.122484] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127915] smp: Brought up 1 node, 4 CPUs <6>[ 0.132140] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.138599] CPU: All CPU(s) started in SVC mode. <6>[ 0.144009] devtmpfs: initialized <6>[ 0.154674] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.160017] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169885] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.180089] pinctrl core: initialized pinctrl subsystem <6>[ 0.184586] DMI not present or invalid. <6>[ 0.187676] NET: Registered protocol family 16 <6>[ 0.195015] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.201693] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.201876] cpuidle: using governor menu <6>[ 0.209924] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.386857] vdd1p1: supplied by regulator-dummy <6>[ 0.395882] vdd3p0: supplied by regulator-dummy <6>[ 0.404833] vdd2p5: supplied by regulator-dummy <6>[ 0.413798] vddarm: supplied by regulator-dummy <6>[ 0.422921] vddpu: supplied by regulator-dummy <6>[ 0.431666] vddsoc: supplied by regulator-dummy <6>[ 0.756511] No ATAGs? <6>[ 0.756692] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.764454] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.774742] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.785125] Serial: AMBA PL011 UART driver <6>[ 0.788829] printk: console [ramoops-1] enabled <6>[ 0.791618] pstore: Registered ramoops as persistent store backend <6>[ 0.797881] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.835740] iommu: Default domain type: Translated <6>[ 0.838458] vgaarb: loaded <5>[ 0.841869] SCSI subsystem initialized <7>[ 0.845314] libata version 3.00 loaded. <6>[ 0.849343] usbcore: registered new interface driver usbfs <6>[ 0.854874] usbcore: registered new interface driver hub <6>[ 0.860463] usbcore: registered new device driver usb <6>[ 0.867257] i2c i2c-0: IMX I2C adapter registered <6>[ 0.871993] i2c i2c-1: IMX I2C adapter registered <6>[ 0.876454] i2c i2c-2: IMX I2C adapter registered <6>[ 0.881907] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.885814] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.895213] PTP clock support registered <6>[ 0.902955] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.043289] NET: Registered protocol family 2 <6>[ 2.045476] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.053920] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.061359] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.069431] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.076891] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.083585] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.090247] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.097729] NET: Registered protocol family 1 <6>[ 2.102739] RPC: Registered named UNIX socket transport module. <6>[ 2.108346] RPC: Registered udp transport module. <6>[ 2.113289] RPC: Registered tcp transport module. <6>[ 2.118231] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.124949] PCI: CLS 0 bytes, default 64 <6>[ 2.129614] Trying to unpack rootfs image as initramfs... <6>[ 3.481467] Freeing initrd memory: 15664K <4>[ 3.483466] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.490699] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.500502] Initialise system trusted keyrings <6>[ 3.503664] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.516157] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.520130] NFS: Registering the id_resolver key type <5>[ 3.524764] Key type id_resolver registered <5>[ 3.529147] Key type id_legacy registered <6>[ 3.533513] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.540370] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.548078] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.553118] Key type asymmetric registered <5>[ 3.556987] Asymmetric key parser 'x509' registered <6>[ 3.562163] bounce: pool size: 64 pages <6>[ 3.566268] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.573882] io scheduler mq-deadline registered <6>[ 3.578650] io scheduler kyber registered <6>[ 3.622538] mxs-dma 110000.dma-apbh: initialized <4>[ 3.629320] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.636268] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.696721] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.705028] SuperH (H)SCI(F) driver initialized <6>[ 3.707976] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.716876] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.724818] printk: console [ttymxc1] enabled <6>[ 3.729317] printk: bootconsole [ec_imx21] disabled <6>[ 3.724818] printk: console [ttymxc1] enabled <6>[ 3.729317] printk: bootconsole [ec_imx21] disabled <6>[ 3.736036] msm_serial: driver initialized <6>[ 3.736303] STMicroelectronics ASC driver initialized <6>[ 3.738289] STM32 USART driver initialized <4>[ 3.749484] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.749651] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.750188] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.758999] brd: module loaded <6>[ 3.768984] loop: module loaded <6>[ 3.772969] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.772986] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.772995] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.773003] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.773085] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.773235] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.773301] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.776151] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.776178] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.776194] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.777713] scsi host0: ahci-imx <6>[ 3.778089] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.790581] CAN device driver interface <6>[ 3.791913] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.795504] pps pps0: new PPS source ptp0 <6>[ 3.828599] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.830129] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.830135] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.830193] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.830199] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.836440] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.836487] usbcore: registered new interface driver pegasus <6>[ 3.836528] usbcore: registered new interface driver asix <6>[ 3.836562] usbcore: registered new interface driver ax88179_178a <6>[ 3.836593] usbcore: registered new interface driver cdc_ether <6>[ 3.836636] usbcore: registered new interface driver smsc75xx <6>[ 3.836688] usbcore: registered new interface driver smsc95xx <6>[ 3.836720] usbcore: registered new interface driver net1080 <6>[ 3.836753] usbcore: registered new interface driver cdc_subset <6>[ 3.836783] usbcore: registered new interface driver zaurus <6>[ 3.836849] usbcore: registered new interface driver cdc_ncm <6>[ 3.840441] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.840448] ehci-pci: EHCI PCI platform driver <6>[ 3.840482] ehci-platform: EHCI generic platform driver <6>[ 3.840773] ehci-orion: EHCI orion driver <6>[ 3.840989] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.841171] ehci-st: EHCI STMicroelectronics driver <6>[ 3.841353] ehci-exynos: EHCI Exynos driver <6>[ 3.841539] ehci-atmel: EHCI Atmel driver <6>[ 3.841717] tegra-ehci: Tegra EHCI driver <6>[ 3.841930] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.841949] ohci-pci: OHCI PCI platform driver <6>[ 3.842000] ohci-platform: OHCI generic platform driver <6>[ 3.842264] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.842449] ohci-st: OHCI STMicroelectronics driver <6>[ 3.842638] ohci-atmel: OHCI Atmel driver <6>[ 3.843761] usbcore: registered new interface driver usb-storage <6>[ 3.851977] i2c /dev entries driver <6>[ 3.871675] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.871682] sdhci: Copyright(c) Pierre Ossman <6>[ 3.874453] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.876415] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.877730] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.877774] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.878731] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.881912] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.882853] usbcore: registered new interface driver usbhid <6>[ 3.882860] usbhid: USB HID core driver <6>[ 3.889511] NET: Registered protocol family 10 <6>[ 3.890563] Segment Routing with IPv6 <6>[ 3.890640] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.891213] NET: Registered protocol family 17 <6>[ 3.891229] can: controller area network core <6>[ 3.891305] NET: Registered protocol family 29 <6>[ 3.891313] can: raw protocol <6>[ 3.891319] can: broadcast manager protocol <6>[ 3.891328] can: netlink gateway - max_hops=1 <5>[ 3.891806] Key type dns_resolver registered <6>[ 3.893919] ThumbEE CPU extension supported. <5>[ 3.893934] Registering SWP/SWPB emulation handler <6>[ 3.894722] printk: console [ttymxc1]: printing thread started <6>[ 3.894912] printk: console [ramoops-1]: printing thread started <5>[ 3.894951] Loading compiled-in X.509 certificates <6>[ 3.899984] pstore: Using crash dump compression: deflate <6>[ 3.911096] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.915008] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <4>[ 3.921536] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.921688] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.923197] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.931614] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.935124] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.935148] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.950161] mmc2: new high speed SDHC card at address 0001 <6>[ 3.950917] mmcblk2: mmc2:0001 SD 14.6 GiB <6>[ 3.962972] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <4>[ 3.963382] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.963387] GPT:7812499 != 30560255 <4>[ 3.963394] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.963396] GPT:7812499 != 30560255 <4>[ 3.963400] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.963439] mmcblk2: p1 p2 p3 <6>[ 3.963644] hub 1-0:1.0: USB hub found <6>[ 3.963712] hub 1-0:1.0: 1 port detected <6>[ 3.965961] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 3.970367] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.970495] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.971864] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.976150] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.976269] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.977606] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.979459] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 3.984866] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.985000] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.986383] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.252924] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.282928] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) <6>[ 4.283292] ata1.00: ATA-8: INTEL SSDSA2CW080G3, 4PC10362, max UDMA/133 <6>[ 4.283301] ata1.00: 156301488 sectors, multi 1: LBA48 NCQ (depth 32) <6>[ 4.283705] ata1.00: configured for UDMA/133 <5>[ 4.284048] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2CW08 0362 PQ: 0 ANSI: 5 <6>[ 4.284684] ata1.00: Enabling discard_zeroes_data <5>[ 4.284927] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB) <5>[ 4.284974] sd 0:0:0:0: [sda] Write Protect is off <5>[ 4.285060] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6>[ 4.288702] ata1.00: Enabling discard_zeroes_data <6>[ 4.289599] sda: sda1 sda2 sda3 <6>[ 4.290540] ata1.00: Enabling discard_zeroes_data <5>[ 4.290949] sd 0:0:0:0: [sda] Attached SCSI disk <4>[ 4.297074] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.297329] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.299433] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.303249] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.483929] hub 1-1:1.0: USB hub found <6>[ 4.484060] hub 1-1:1.0: 3 ports detected <4>[ 4.488894] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.489020] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.490375] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 6.403442] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 6.413077] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.442977] Sending DHCP requests ., OK <6>[ 6.483051] IP-Config: Got DHCP answer from 192.168.101.1, my address is 192.168.101.99 <6>[ 6.483076] IP-Config: Complete: <6>[ 6.483082] device=eth0, hwaddr=00:19:b8:07:40:03, ipaddr=192.168.101.99, mask=255.255.255.0, gw=192.168.101.1 <6>[ 6.483105] host=imx6q-sabrelite-cbg-0, domain=lava.cbg.collabora.co.uk, nis-domain=(none) <6>[ 6.483119] bootserver=192.168.101.1, rootserver=192.168.101.1, rootpath= <6>[ 6.483134] nameserver0=192.168.101.1 <6>[ 6.491581] Freeing unused kernel memory: 2048K <6>[ 6.553282] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.681755] udevd[138]: starting version 3.2.9 <5>[ 6.682551] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.682760] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.682854] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.690885] udevd[138]: specified user 'tss' unknown <27>[ 6.691038] udevd[138]: specified group 'tss' unknown <30>[ 6.693594] udevd[139]: starting eudev-3.2.9 <6>[ 7.008311] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 7.010165] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 7.015401] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.015713] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.018293] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.046223] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.046382] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.047975] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.054870] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.055051] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.056837] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.159509] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.159682] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.161591] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.169793] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.170112] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.170404] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.170485] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.170654] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.170717] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.170730] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.171097] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 7.172007] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.172146] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.172262] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.172355] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.174694] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.174876] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.176515] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.182606] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.182665] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.182719] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.182762] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.301585] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.301757] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.303776] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.381089] caam 2100000.crypto: Entropy delay = 3200 <6>[ 7.441886] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 7.453240] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.453303] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.453363] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.453406] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 7.502646] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 7.502664] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 7.502673] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 7.507830] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.507992] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.509587] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.590564] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.590632] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.590691] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.590734] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.641824] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 7.642028] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 7.642178] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 7.642292] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 7.644063] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.644233] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.646250] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.667099] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.667190] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.667255] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.667324] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.739322] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.739539] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.742019] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.773697] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.773793] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.773816] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.773895] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.773975] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 7.778069] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 7.839990] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.840248] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.842533] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.866160] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.866243] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.866318] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.866362] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.102285] caam algorithms registered in /proc/crypto <6>[ 8.103843] caam 2100000.crypto: registering rng-caam <4>[ 8.105665] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.105844] panel-simple panel-lcd: Specify missing connector_type done <4>[ 8.107683] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.115203] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) Saving random seed: <6>[ 8.115279] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) OK <6>[ 8.115347] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) Starting network: <6>[ 8.115393] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.117014] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.117220] panel-simple panel-lcd: Specify missing connector_type ip: RTNETLINK answers: File exist<4>[ 8.119076] panel-simple panel-lvds0: supply power not found, using dummy regulator s FAIL <6>[ 8.126038] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.126102] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.126160] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.126205] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <5>[ 8.205876] random: dd: uninitialized urandom read (32 bytes read) <5>[ 8.286260] random: crng init done Starting dropbear sshd: <5>[ 8.286270] random: 1 urandom warning(s) missed due to ratelimiting OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-8333591/environment . /lava-8333591/environment / # /lava-8333591/bin/lava-test-runner /lava-8333591/0 /lava-8333591/bin/lava-test-runner /lava-8333591/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-8333591/0/tests/0_dmesg + cat uuid + UUID=8333591_1.5.2.4.1 + set +x + KERNELCI_LAVA=y<8>[ 8.888053] /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.927320] <8>[ 8.960741] + set +x / # # export SHELL=/bin/sh <8>[ 8.994651] <8>[ 8.995937] # / # export SHELL=/bin/sh. /lava-8333591/environment / # . /lava-8333591/environment/lava-8333591/bin/lava-test-runner /lava-8333591/1 / # /lava-8333591/bin/lava-test-runner /lava-8333591/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-8333591/1/tests/1_bootrr + cat uuid + UUID=8333591_1.5.2<8>[ 9.482214] .4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-8333591/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-8333591/1/../bin/lava-test-case <8>[ 10.531702] /lava-8333591/1/../bin/lava-test-case /lava-8333591/1/../bin/lava-test-<8>[ 10.565360] case <8>[ 10.583097] + set +x / #