Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3027 device /dev/ttyimx8mp-evk-1 [115200 N81] (Debian GNU/Linux) U-Boot SPL 2019.04-5.4.3-2.0.0+g47c1922978 (Mar 13 2020 - 23:25:39 +0000) power_pca9450b_init DDRINFO: start DRAM init DDRINFO:ddrphy calibration done DDRINFO: ddrmix config done Normal Boot Trying to boot from ROMAPI image offset 0x8000, pagesize 0x200, ivt offset 0x0 U-Boot 2019.04-5.4.3-2.0.0+g47c1922978 (Mar 13 2020 - 23:25:39 +0000) CPU: Freescale i.MX8MP rev1.0 1800 MHz (running at 1200 MHz) CPU: Commercial temperature grade (0C to 95C) at 24C Reset cause: POR Model: NXP i.MX8MPlus LPDDR4 EVK board DRAM: 6 GiB TCPC: Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C2 0x50] SNK.Power3.0 on CC2 PDO 0: type 0, 5000 mV, 3000 mA [E] PDO 1: type 0, 9000 mV, 3000 mA [] PDO 2: type 0, 15000 mV, 3000 mA [] PDO 3: type 0, 20000 mV, 2250 mA [] Requesting PDO 3: 20000 mV, 2250 mA Source accept request PD source ready! tcpc_pd_receive_message: Polling ALERT register, TCPC_ALERT_RX_STATUS bit failed, ret = -62 Power supply on USB2 TCPC: Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C1 0x50] MMC: FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... Run CMD11 1.8V switch OK No panel detected: default to MIPI2HDMI adv7535_init: Can't find device id=0x3d, on bus 1 Display: MIPI2HDMI (1920x1080) Video: 1920x1080x24 In: serial Out: serial Err: serial BuildInfo: - ATF f1a195b - U-Boot 2019.04-5.4.3-2.0.0+g47c1922978 Run CMD11 1.8V switch switch to partitions #0, OK mmc1 is current device flash target is MMC:1 Run CMD11 1.8V switch Net: eth0: ethernet@30be0000 [PRIME], eth1: ethernet@30bf0000 Fastboot: Normal Normal Boot Hit any key to stop autoboot: 2  0 u-boot=> setenv autoload no setenv autoload no u-boot=> dhcp dhcp ethernet@30be0000 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.178 (1695 ms) u-boot=> setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 u-boot=> tftp 0x40480000 1147090/tftp-deploy-b2193m3p/kernel/Image tftp 0x40480000 1147090/tftp-deploy-b2193m3p/kernel/Image Using ethernet@30be0000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.178; sending through gateway 172.16.1.4 Filename '1147090/tftp-deploy-b2193m3p/kernel/Image'. Load address: 0x40480000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 11.7 MiB/s done Bytes transferred = 32629248 (1f1e200 hex) u-boot=> tftp 0x44000000 1147090/tftp-deploy-b2193m3p/ramdisk/ramdisk.cpio.gz.uboot tftp 0x44000000 1147090/tftp-deploy-b2193m3p/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@30be0000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.178; sending through gateway 172.16.1.4 Filename '1147090/tftp-deploy-b2193m3p/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x44000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #### 11.2 MiB/s done Bytes transferred = 19132665 (123f0f9 hex) u-boot=> setenv initrd_size ${filesize} setenv initrd_size ${filesize} u-boot=> tftp 0x43000000 1147090/tftp-deploy-b2193m3p/dtb/imx8mp-evk.dtb tftp 0x43000000 1147090/tftp-deploy-b2193m3p/dtb/imx8mp-evk.dtb Using ethernet@30be0000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.178; sending through gateway 172.16.1.4 Filename '1147090/tftp-deploy-b2193m3p/dtb/imx8mp-evk.dtb'. Load address: 0x43000000 Loading: *## 3.5 MiB/s done Bytes transferred = 18268 (475c hex) u-boot=> setenv bootargs 'console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' u-boot=> booti 0x40480000 0x44000000 0x43000000 booti 0x40480000 0x44000000 0x43000000 ## Loading init Ramdisk from Legacy Image at 44000000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 19132601 Bytes = 18.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Using Device Tree in place at 0000000043000000, end 000000004300775b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.162-cip24-rt10 (KernelCI@build-j927136-arm64-gcc-10-defconfig-preempt-rt-jl9fw) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Jan 27 00:52:17 UTC 2023 [ 0.000000] Machine model: NXP i.MX8MPlus EVK board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x0000000030890000 (options '115200n8') [ 0.000000] printk: bootconsole [ec_imx6q0] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x0000000030890000 (options '115200n8') [ 0.000000] ------------[ cut here ]------------ [ 0.000000] console 'ec_imx6q0' already registered [ 0.000000] WARNING: CPU: 0 PID: 0 at kernel/printk/printk.c:2777 register_console+0x58/0x324 [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 5.10.162-cip24-rt10 #1 [ 0.000000] Hardware name: NXP i.MX8MPlus EVK board (DT) [ 0.000000] pstate: 60000085 (nZCv daIf -PAN -UAO -TCO BTYPE=--) [ 0.000000] pc : register_console+0x58/0x324 [ 0.000000] lr : register_console+0x58/0x324 [ 0.000000] sp : ffff800011c53de0 [ 0.000000] x29: ffff800011c53de0 x28: 0000000041c70018 [ 0.000000] x27: 0000000000000400 x26: 0000000000000000 [ 0.000000] x25: 0000000000002f68 x24: ffff800011ea5000 [ 0.000000] x23: 0000000000000000 x22: ffff8000117bb1f8 [ 0.000000] x21: ffff800011f2f098 x20: ffff800011ea5ca8 [ 0.000000] x19: ffff800011ea5ca8 x18: 0000000000000005 [ 0.000000] x17: 0000000000001800 x16: 0000000000000000 [ 0.000000] x15: 0000000000000030 x14: ffffffffffffffff [ 0.000000] x13: ffff800091c53a47 x12: ffff800011c53a54 [ 0.000000] x11: ffff800011c72c88 x10: ffff800011ccaa88 [ 0.000000] x9 : ffff800011c53980 x8 : 36786d695f636527 [ 0.000000] x7 : 20656c6f736e6f63 x6 : ffff800011ea5d0f [ 0.000000] x5 : 0000000000000001 x4 : 0000000000000006 [ 0.000000] x3 : ffff800011c72928 x2 : 0000000000000000 [ 0.000000] x1 : 0000000000000000 x0 : ffff800011c633c0 [ 0.000000] Call trace: [ 0.000000] register_console+0x58/0x324 [ 0.000000] of_setup_earlycon+0x248/0x26c [ 0.000000] early_init_dt_scan_chosen_stdout+0x160/0x1a4 [ 0.000000] acpi_boot_table_init+0x158/0x198 [ 0.000000] setup_arch+0x284/0x600 [ 0.000000] start_kernel+0x74/0x4c4 [ 0.000000] ---[ end trace 6f9f89fe29c58d96 ]--- [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0# 000000040000000-0x00000001bfffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x1bf3f6b00-0x1bf3f8fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000001bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000055ffffff] [ 0.000000] node 0: [mem 0x0000000058000000-0x00000001bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000001bfffffff] [ 0.000000] On node 0 totalpages: 1564672 [ 0.000000] DMA zone: 12288 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 778240 pages, LIFO batch:63 [ 0.000000] Normal zone: 12288 pages used for memmap [ 0.000000] Normal zone: 786432 pages, LIFO batch:63 [ 0.000000] cma: Reserved 32 MiB at 0x00000000fe000000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 19 pages/cpu s40024 r8192 d29608 u77824 [ 0.000000] pcpu-alloc: s40024 r8192 d29608 u77824 alloc=19*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1540096 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000fa000000-0x00000000fe000000] (64MB) <6>[ 0.000000] Memory: 5985612K/6258688K available (15040K kernel code, 2872K rwdata, 7804K rodata, 6016K init, 504K bss, 240308K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 160 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] GICv3: Distributor has no Range Selector support <6>[ 0.000000] GICv3: 16 PPIs implemented <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000038880000 <4>[ 0.000000] ITS: No ITS available, not enabling LPIs <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns <6>[ 0.000000] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns <6>[ 0.008845] Console: colour dummy device 80x25 <6>[ 0.013105] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.00 BogoMIPS (lpj=32000) <6>[ 0.023629] pid_max: default: 32768 minimum: 301 <6>[ 0.028589] LSM: Security Framework initializing <6>[ 0.033480] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.041319] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.050761] rcu: Hierarchical SRCU implementation. <6>[ 0.055844] EFI services will not be available. <6>[ 0.059705] smp: Bringing up secondary CPUs ... <6>[ 0.064698] Detected VIPT I-cache on CPU1 <6>[ 0.068617] GICv3: CPU1: found redistributor 1 region 0:0x00000000388a0000 <6>[ 0.075802] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] <6>[ 0.083039] Detected VIPT I-cache on CPU2 <6>[ 0.086900] GICv3: CPU2: found redistributor 2 region 0:0x00000000388c0000 <6>[ 0.094075] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] <6>[ 0.101305] Detected VIPT I-cache on CPU3 <6>[ 0.105185] GICv3: CPU3: found redistributor 3 region 0:0x00000000388e0000 <6>[ 0.112362] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] <6>[ 0.119242] smp: Brought up 1 node, 4 CPUs <6>[ 0.123557] SMP: Total of 4 processors activated. <6>[ 0.128540] CPU features: detected: 32-bit EL0 Support <6>[ 0.133966] CPU features: detected: CRC32 instructions <6>[ 0.139391] CPU features: detected: 32-bit EL1 Support <6>[ 0.154742] CPU: All CPU(s) started at EL2 <6>[ 0.156273] alternatives: patching kernel code <6>[ 0.162746] devtmpfs: initialized <4>[ 0.167141] KASLR disabled due to lack of seed <6>[ 0.169411] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.179364] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.187526] pinctrl core: initialized pinctrl subsystem <6>[ 0.192969] DMI not present or invalid. <6>[ 0.196753] NET: Registered protocol family 16 <6>[ 0.202005] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.208529] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.216859] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.224796] audit: initializing netlink subsys (disabled) <5>[ 0.230578] audit: type=2000 audit(0.164:1): state=initialized audit_enabled=0 res=1 <6>[ 0.231352] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.231356] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.238528] cpuidle: using governor menu <6>[ 0.255989] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.262978] ASID allocator initialised with 65536 entries <6>[ 0.269783] Serial: AMBA PL011 UART driver <6>[ 0.286346] imx8mp-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver <6>[ 0.301119] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.305275] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.312273] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.319265] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.327175] cryptd: max_cpu_qlen set to 1000 <6>[ 0.333014] ACPI: Interpreter disabled. <6>[ 0.336295] iommu: Default domain type: Translated <6>[ 0.340260] vgaarb: loaded <5>[ 0.343294] SCSI subsystem initialized <7>[ 0.347210] libata version 3.00 loaded. <6>[ 0.351368] usbcore: registered new interface driver usbfs <6>[ 0.357009] usbcore: registered new interface driver hub <6>[ 0.362596] usbcore: registered new device driver usb <6>[ 0.368557] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.373165] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.382624] PTP clock support registered <6>[ 0.386907] EDAC MC: Ver: 3.0.0 <6>[ 0.391214] FPGA manager framework <6>[ 0.393973] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.400955] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.406825] VFS: Disk quotas dquot_6.6.0 <6>[ 0.410923] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.418200] pnp: PnP ACPI: disabled <6>[ 0.426737] NET: Registered protocol family 2 <6>[ 0.428737] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear) <6>[ 0.439252] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear) <6>[ 0.445308] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.453853] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear) <6>[ 0.461995] TCP: Hash tables configured (established 65536 bind 65536) <6>[ 0.468108] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear) <6>[ 0.475214] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear) <6>[ 0.482832] NET: Registered protocol family 1 <6>[ 0.487584] RPC: Registered named UNIX socket transport module. <6>[ 0.493451] RPC: Registered udp transport module. <6>[ 0.498430] RPC: Registered tcp transport module. <6>[ 0.503413] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.510155] PCI: CLS 0 bytes, default 64 <6>[ 0.514490] Unpacking initramfs... <6>[ 1.407679] Freeing initrd memory: 18680K <6>[ 1.409808] kvm [1]: IPA Size Limit: 40 bits <6>[ 1.415267] kvm [1]: GICv3: no GICV resource entry <6>[ 1.418796] kvm [1]: disabling GICv2 emulation <6>[ 1.423483] kvm [1]: GIC system register CPU interface enabled <6>[ 1.429785] kvm [1]: vgic interrupt IRQ9 <6>[ 1.433908] kvm [1]: Hyp mode initialized successfully <5>[ 1.442200] Initialise system trusted keyrings <6>[ 1.444181] workingset: timestamp_bits=42 max_order=21 bucket_order=0 <6>[ 1.456272] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.460102] NFS: Registering the id_resolver key type <5>[ 1.464937] Key type id_resolver registered <5>[ 1.469341] Key type id_legacy registered <6>[ 1.473691] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.480629] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.488449] 9p: Installing v9fs 9p2000 file system support <5>[ 1.530408] Key type asymmetric registered <5>[ 1.531915] Asymmetric key parser 'x509' registered <6>[ 1.537106] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.544782] io scheduler mq-deadline registered <6>[ 1.549594] io scheduler kyber registered <4>[ 1.561431] EINJ: ACPI disabled. <3>[ 1.566663] clk: failed to reparent gic to sys_pll2_500m: -16 <6>[ 1.575019] SoC: i.MX8MP revision 1.0 <6>[ 1.582116] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.587680] SuperH (H)SCI(F) driver initialized <6>[ 1.591078] 30890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 30, base_baud = 1500000) is a IMX <6>[ 1.599796] printk: console [ttymxc1] enabled <6>[ 1.604339] printk: bootconsole [ec_imx6q0] disabled <6>[ 1.599796] printk: console [ttymxc1] enabled <6>[ 1.604339] printk: bootconsole [ec_imx6q0] disabled <6>[ 1.610101] msm_serial: driver initialized <6>[ 1.616606] loop: module loaded <6>[ 1.617273] megasas: 07.714.04.00-rc1 <6>[ 1.621678] tun: Universal TUN/TAP device driver, 1.6 <6>[ 1.622255] thunder_xcv, ver 1.0 <6>[ 1.622282] thunder_bgx, ver 1.0 <6>[ 1.622314] nicpf, ver 1.0 <6>[ 1.623092] pps pps0: new PPS source ptp0 <6>[ 1.639372] hclge is initializing <6>[ 1.639394] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 1.639398] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 1.639432] e1000: Intel(R) PRO/1000 Network Driver <6>[ 1.639435] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 1.639468] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.639470] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.639498] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.639501] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.639522] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 1.639527] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 1.639757] sky2: driver version 1.30 <6>[ 1.640576] VFIO - User Level meta-driver version: 0.3 <6>[ 1.641914] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.641919] ehci-pci: EHCI PCI platform driver <6>[ 1.641945] ehci-platform: EHCI generic platform driver <6>[ 1.642034] ehci-orion: EHCI orion driver <6>[ 1.642103] ehci-exynos: EHCI Exynos driver <6>[ 1.642165] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.642180] ohci-pci: OHCI PCI platform driver <6>[ 1.642209] ohci-platform: OHCI generic platform driver <6>[ 1.642288] ohci-exynos: OHCI Exynos driver <6>[ 1.642657] usbcore: registered new interface driver usb-storage <6>[ 1.644564] i2c /dev entries driver <6>[ 1.649634] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.649640] sdhci: Copyright(c) Pierre Ossman <6>[ 1.650021] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.650741] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.652210] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.653449] usbcore: registered new interface driver usbhid <6>[ 1.653456] usbhid: USB HID core driver <6>[ 1.656243] optee: probing for conduit method. <6>[ 1.656261] optee: revision 3.7 (b32a9b6b) <6>[ 1.656659] optee: initialized driver <6>[ 1.657882] NET: Registered protocol family 17 <6>[ 1.658008] 9pnet: Installing 9P2000 support <5>[ 1.658057] Key type dns_resolver registered <6>[ 1.658344] printk: console [ttymxc1]: printing thread started <6>[ 1.658397] registered taskstats version 1 <5>[ 1.658402] Loading compiled-in X.509 certificates <4>[ 1.677552] pca953x 2-0020: supply vcc not found, using dummy regulator <6>[ 1.677657] pca953x 2-0020: using no AI <6>[ 1.678997] i2c i2c-2: IMX I2C adapter registered <6>[ 1.681064] pps pps0: new PPS source ptp0 <6>[ 1.685003] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA <6>[ 1.764307] mmc2: new HS400 MMC card at address 0001 <6>[ 1.764785] mmcblk2: mmc2:0001 IB2932 29.2 GiB <6>[ 1.764936] mmcblk2boot0: mmc2:0001 IB2932 partition 1 4.00 MiB <6>[ 1.765087] mmcblk2boot1: mmc2:0001 IB2932 partition 2 4.00 MiB <6>[ 1.765195] mmcblk2rpmb: mmc2:0001 IB2932 partition 3 4.00 MiB, chardev (234:0) <6>[ 1.889615] fec 30be0000.ethernet eth0: registered PHC device 0 <6>[ 1.894870] sdhci-esdhc-imx 30b50000.mmc: Got CD GPIO <6>[ 1.925071] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA <6>[ 2.044969] RTL8211F Gigabit Ethernet 30be0000.ethernet-1:01: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=30be0000.ethernet-1:01, irq=POLL) <4>[ 2.057948] mmc1: host does not support reading read-only switch, assuming write-enable <6>[ 2.061649] mmc1: new ultra high speed DDR50 SDHC card at address aaaa <6>[ 2.062179] mmcblk1: mmc1:aaaa SL16G 14.8 GiB <6>[ 2.069477] mmcblk1: p1 p2 <6>[ 6.165750] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <5>[ 6.196961] Sending DHCP requests .., OK <6>[ 8.908976] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.178 <6>[ 8.908985] IP-Config: Complete: <6>[ 8.908987] device=eth0, hwaddr=00:04:9f:06:96:3c, ipaddr=172.16.1.178, mask=255.255.255.0, gw=172.16.1.4 <6>[ 8.908996] host=172.16.1.178, domain=example.org, nis-domain=(none) <6>[ 8.909000] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 8.909004] nameserver0=172.16.1.4 <6>[ 8.910728] ALSA device list: <6>[ 8.910733] No soundcards found. <6>[ 8.912744] Freeing unused kernel memory: 6016K <6>[ 8.985021] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 9.035223] udevd[161]: starting version 3.2.9 <5>[ 9.035797] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 9.035920] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 9.035962] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 9.040312] udevd[161]: specified user 'tss' unknown <27>[ 9.040381] udevd[161]: specified group 'tss' unknown <30>[ 9.041589] udevd[162]: starting eudev-3.2.9 <6>[ 9.306643] caam 30900000.crypto: RNG4 SH0 was previously instantiated without prediction resistance. Tearing it down <6>[ 9.320557] input: 30370000.snvs:snvs-powerkey as /devices/platform/soc@0/30000000.bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0 <6>[ 9.336400] snvs_rtc 30370000.snvs:snvs-rtc-lp: registered as rtc0 <6>[ 9.336438] snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01T00:00:00 UTC (0) <3>[ 9.364674] caam 30900000.crypto: failed to acquire DECO 0 <3>[ 9.364686] caam 30900000.crypto: Failed to deinstantiate RNG4 SH0 <3>[ 9.364694] caam 30900000.crypto: failed to instantiate RNG <4>[ 9.388503] imx-sdma 30bd0000.dma-controller: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 <4>[ 9.388516] imx-sdma 30bd0000.dma-controller: Falling back to sysfs fallback for: imx/sdma/sdma-imx7d.bin done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK <6>[ 9.577607] NET: Registered protocol family 10 <6>[ 9.578350] Segment Routing with IPv6 /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1147090/environment . /lava-1147090/environment / # /lava-1147090/bin/lava-test-runner /lava-1147090/0 /lava-1147090/bin/lava-test-runner /lava-1147090/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1147090/0/tests/0_dmesg + c<8>[ 15.342564] at uuid + UUID=1147090_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 15.358827] <8>[ 15.373402] + set +x <8>[ 15.387867] <8>[ 15.388645] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1147090/environment / # . /lava-1147090/environment/lava-1147090/bin/lava-test-runner /lava-1147090/1 / # /lava-1147090/bin/lava-test-runner /lava-1147090/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1147090/1/tests/1_bootrr + cat uuid + UUID=1147090_1.5.2<8>[ 21.077266] .4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1147090/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + s<8>[ 21.097194] h helpers/bootrr-auto /lava-1147090/1/../bin/lava-test-case /lava-1147090/1/../bin/lava-test-<8>[ 21.115478] case /lava-1147090/1/../bin/lava-test-case <8>[ 21.131242] + set +x <8>[ 21.140632] / #