Trying 10.1.1.35... Connected to potato3.baylibre. Escape character is '^]'. GXL:BL1:9ac50e:bb16dc;FEAT:ADFC318C:0;POC:0;RCY:0;USB:0;SPI:0;CHK:A7;EMMC:400;NAND:81;SD:0;READ:0;0.0;CHK:0; no sdio debug board detected TE: 1827896 BL2 Built : 11:58:42, May 27 2017. gxl gc3c9a84 - xiaobo.gu@droid05 set vcck to 1120 mv set vddee to 1000 mv Board ID = 6 CPU clk: 1200MHz DQS-corr enabled DDR scramble enabled DDR3 chl: Rank0+1 @ 912MHz - PASS Rank0: 1024MB(auto)-2T-13 Rank1: 1024MB(auto)-2T-13 DataBus test pass! AddrBus test pass! Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000 New fip structure! Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600 Load bl31 from SD, src: 0x00020200, des: 0x05100000, size: 0x00018400 Load bl33 from SD, src: 0x0003c200, des: 0x01000000, size: 0x000aa400 NOTICE: BL3-1: v1.0(release):3348978 NOTICE: BL3-1: Built : 15:44:01, May 12 2017 [BL31]: GXL CPU setup! mpu_config_enable:ok [Image: gxl_v1.1.3221-2cfba69 2017-05-27 16:03:58 qiufang.dai@droid07] OPS=0x84 48 38 b be a2 f0 dc eb 16 d9 1e b2 [2.226817 Inits done] secure task start! high task start! low task start! ERROR: Error initializing runtime service opteed_fast U-Boot 2022.04 (Jun 20 2022 - 14:54:39 +0000) libretech-cc Model: Libre Computer AML-S905X-CC SoC: Amlogic Meson GXL (S905X) Revision 21:d (84:2) DRAM: 2 GiB Core: 160 devices, 24 uclasses, devicetree: separate MMC: mmc@72000: 0, mmc@74000: 1 Loading Environment from nowhere... OK In: serial Out: serial Err: serial [BL31]: tee size: 0 [BL31]: tee size: 0 Net: eth0: ethernet@c9410000 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp ethernet@c9410000 Waiting for PHY auto negotiation to complete... done Speed: 100, full duplex BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 10.201.3.5 (260 ms) => setenv serverip 10.201.1.11 setenv serverip 10.201.1.11 => tftp 0x8080000 3222361/tftp-deploy-avz8n4fb/kernel/uImage tftp 0x8080000 3222361/tftp-deploy-avz8n4fb/kernel/uImage Speed: 100, full duplex Using ethernet@c9410000 device TFTP from server 10.201.1.11; our IP address is 10.201.3.5 Filename '3222361/tftp-deploy-avz8n4fb/kernel/uImage'. Load address: 0x8080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########T #T ######################################################## ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################### 1.7 MiB/s done Bytes transferred = 31844928 (1e5ea40 hex) => tftp 0x13000000 3222361/tftp-deploy-avz8n4fb/ramdisk/ramdisk.cpio.gz.uboot tftp 0x13000000 3222361/tftp-deploy-avz8n4fb/ramdisk/ramdisk.cpio.gz.uboot Speed: 100, full duplex Using ethernet@c9410000 device TFTP from server 10.201.1.11; our IP address is 10.201.3.5 Filename '3222361/tftp-deploy-avz8n4fb/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x13000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #### 3.7 MiB/s done Bytes transferred = 15320923 (e9c75b hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x8008000 3222361/tftp-deploy-avz8n4fb/dtb/meson-gxl-s905x-libretech-cc.dtb tftp 0x8008000 3222361/tftp-deploy-avz8n4fb/dtb/meson-gxl-s905x-libretech-cc.dtb Speed: 100, full duplex Using ethernet@c9410000 device TFTP from server 10.201.1.11; our IP address is 10.201.3.5 Filename '3222361/tftp-deploy-avz8n4fb/dtb/meson-gxl-s905x-libretech-cc.dtb'. Load address: 0x8008000 Loading: *## 3.1 MiB/s done Bytes transferred = 28939 (710b hex) => setenv bootargs 'console=ttyAML0,115200n8 root=/dev/nfs rw nfsroot=10.201.1.11:/var/lib/lava/dispatcher/tmp/3222361/extract-nfsrootfs-v2dgv7xa,tcp,hard ip=dhcp' setenv bootargs 'console=ttyAML0,115200n8 root=/dev/nfs rw nfsroot=10.201.1.11:/var/lib/lava/dispatcher/tmp/3222361/extract-nfsrootfs-v2dgv7xa,tcp,hard ip=dhcp' => bootm 0x8080000 0x13000000 0x8008000 bootm 0x8080000 0x13000000 0x8008000 ## Booting kernel from Legacy Image at 08080000 ... Image Name: Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 31844864 Bytes = 30.4 MiB Load Address: 08080000 Entry Point: 08080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 13000000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 15320859 Bytes = 14.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 08008000 Booting using the fdt blob at 0x8008000 Loading Kernel Image Loading Ramdisk to 7b0a7000, end 7bf4371b ... OK Loading Device Tree to 000000007b09c000, end 000000007b0a610a ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.162-cip24-rt10 (KernelCI@build-j927262-arm64-gcc-10-defconfig-4klm8) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Fri Jan 27 00:52:47 UTC 2023 [ 0.000000] Machine model: Libre Computer AML-S905X-CC [ 0.000000] efi: UEFI not found. [ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'hwrom@0': base 0x0000000000000000, size 16 MiB [ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'secmon@5000000': base 0x0000000005000000, size 3 MiB [ 0.000000] Reserved memory: created CMA memory pool at 0x000000006b000000, size 256 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000007fe5afff] [ 0.000000] NUMA: NODE_DATA [mem 0x7fa40b00-0x7fa42fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000007fe5afff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x00000000052fffff] [ 0.000000] node 0: [mem 0x0000000005300000-0x00000000072fffff] [ 0.000000] node 0: [mem 0x0000000007300000-0x000000000fffffff] [ 0.000000] node 0: [mem 0x0000000010000000-0x00000000101fffff] [ 0.000000] node 0: [mem 0x0000000010200000-0x000000007fe5afff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fe5afff] [ 0.000000] On node 0, zone DMA: 421 pages in unavailable ranges [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] percpu: Embedded 19 pages/cpu s40344 r8192 d29288 u77824 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 515681 [ 0.000000] Policy zone: DMA [ 0.000000] Kernel command line: console=ttyAML0,115200n8 root=/dev/nfs rw nfsroot=10.201.1.11:/var/lib/lava/dispatcher/tmp/3222361/extract-nfsrootfs-v2dgv7xa,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1692020K/2095468K available (14528K kernel code, 2874K rwdata, 7608K rodata, 5952K init, 502K bss, 141304K reserved, 262144K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] irq_meson_gpio: 110 to 8 gpio interrupt mux initialized [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000970] Console: colour dummy device 80x25 [ 0.001060] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.001070] pid_max: default: 32768 minimum: 301 [ 0.001140] LSM: Security Framework initializing [ 0.001193] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.001208] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.002547] rcu: Hierarchical SRCU implementation. [ 0.004757] EFI services will not be available. [ 0.005091] smp: Bringing up secondary CPUs ... [ 0.005583] Detected VIPT I-cache on CPU1 [ 0.005653] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.006227] Detected VIPT I-cache on CPU2 [ 0.006282] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.006853] Detected VIPT I-cache on CPU3 [ 0.006907] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.006991] smp: Brought up 1 node, 4 CPUs [ 0.006997] SMP: Total of 4 processors activated. [ 0.007002] CPU features: detected: 32-bit EL0 Support [ 0.007006] CPU features: detected: CRC32 instructions [ 0.007011] CPU features: detected: 32-bit EL1 Support [ 0.013834] CPU: All CPU(s) started at EL2 [ 0.013893] alternatives: patching kernel code [ 0.014927] devtmpfs: initialized [ 0.019404] KASLR disabled due to lack of seed [ 0.019576] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.019593] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.027013] pinctrl core: initialized pinctrl subsystem [ 0.028202] DMI not present or invalid. [ 0.028829] NET: Registered protocol family 16 [ 0.030446] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations [ 0.030598] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.030763] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.030845] audit: initializing netlink subsys (disabled) [ 0.031059] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1 [ 0.032105] thermal_sys: Registered thermal governor 'step_wise' [ 0.032114] thermal_sys: Registered thermal governor 'power_allocator' [ 0.032321] cpuidle: using governor menu [ 0.032493] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.d [ 0.032588] ASID allocator initialised with 32768 entries [ 0.034017] Serial: AMBA PL011 UART driver [ 0.066850] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.066863] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.066867] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.066871] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.067911] cryptd: max_cpu_qlen set to 1000 [ 0.070181] ACPI: Interpreter disabled. [ 0.071906] VDDIO_BOOT: supplied by VCC_3V3 [ 0.072881] iommu: Default domain type: Translated [ 0.073151] vgaarb: loaded [ 0.073448] SCSI subsystem initialized [ 0.073805] usbcore: registered new interface driver usbfs [ 0.073837] usbcore: registered new interface driver hub [ 0.073874] usbcore: registered new device driver usb [ 0.074593] pps_core: LinuxPPS API ver. 1 registered [ 0.074598] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.074609] PTP clock support registered [ 0.074723] EDAC MC: Ver: 3.0.0 [ 0.076228] FPGA manager framework [ 0.076310] Advanced Linux Sound Architecture Driver Initialized. [ 0.077126] clocksource: Switched to clocksource arch_sys_counter [ 0.077312] VFS: Disk quotas dquot_6.6.0 [ 0.077358] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.077534] pnp: PnP ACPI: disabled [ 0.082458] NET: Registered protocol family 2 [ 0.082625] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.083610] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.083691] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.083802] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear) [ 0.083998] TCP: Hash tables configured (established 16384 bind 16384) [ 0.084122] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.084169] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.084331] NET: Registered protocol family 1 [ 0.084785] RPC: Registered named UNIX socket transport module. [ 0.084793] RPC: Registered udp transport module. [ 0.084795] RPC: Registered tcp transport module. [ 0.084798] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.084806] PCI: CLS 0 bytes, default 64 [ 0.084966] Unpacking initramfs... [ 0.762254] Freeing initrd memory: 14960K [ 0.762914] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available [ 0.763295] kvm [1]: IPA Size Limit: 40 bits [ 0.764453] kvm [1]: vgic interrupt IRQ9 [ 0.764563] kvm [1]: Hyp mode initialized successfully [ 0.767968] Initialise system trusted keyrings [ 0.768186] workingset: timestamp_bits=42 max_order=19 bucket_order=0 [ 0.773583] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.774205] NFS: Registering the id_resolver key type [ 0.774269] Key type id_resolver registered [ 0.774272] Key type id_legacy registered [ 0.774343] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.774347] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.774516] 9p: Installing v9fs 9p2000 file system support [ 0.809782] Key type asymmetric registered [ 0.809793] Asymmetric key parser 'x509' registered [ 0.809853] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.809859] io scheduler mq-deadline registered [ 0.809863] io scheduler kyber registered [ 0.821788] EINJ: ACPI disabled. [ 0.833463] soc soc0: Amlogic Meson GXL (S905X) Revision 21:d (84:2) Detected [ 0.840448] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.842988] SuperH (H)SCI(F) driver initialized [ 0.843580] c81004c0.serial: ttyAML0 at MMIO 0xc81004c0 (irq = 22, base_baud = 1500000) is a meson_uart [ 0.843643] printk: console [ttyAML0] enabled [ 0.844454] msm_serial: driver initialized [ 0.853199] loop: module loaded [ 0.854103] megasas: 07.714.04.00-rc1 [ 0.859952] tun: Universal TUN/TAP device driver, 1.6 [ 0.860876] thunder_xcv, ver 1.0 [ 0.860914] thunder_bgx, ver 1.0 [ 0.860940] nicpf, ver 1.0 [ 0.862221] hclge is initializing [ 0.862251] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 0.862254] hns3: Copyright (c) 2017 Huawei Corporation. [ 0.862315] e1000: Intel(R) PRO/1000 Network Driver [ 0.862319] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 0.862354] e1000e: Intel(R) PRO/1000 Network Driver [ 0.862357] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.862390] igb: Intel(R) Gigabit Ethernet Network Driver [ 0.862393] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.862416] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 0.862419] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.862781] sky2: driver version 1.30 [ 0.863936] VFIO - User Level meta-driver version: 0.3 [ 0.866311] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.866322] ehci-pci: EHCI PCI platform driver [ 0.866351] ehci-platform: EHCI generic platform driver [ 0.866502] ehci-orion: EHCI orion driver [ 0.866622] ehci-exynos: EHCI Exynos driver [ 0.866714] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.866744] ohci-pci: OHCI PCI platform driver [ 0.866781] ohci-platform: OHCI generic platform driver [ 0.866902] ohci-exynos: OHCI Exynos driver [ 0.867465] usbcore: registered new interface driver usb-storage [ 0.870289] i2c /dev entries driver [ 0.877352] sdhci: Secure Digital Host Controller Interface driver [ 0.877361] sdhci: Copyright(c) Pierre Ossman [ 0.878015] Synopsys Designware Multimedia Card Interface Driver [ 0.879332] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.879574] meson-gx-mmc d0074000.mmc: allocated mmc-pwrseq [ 0.882641] ledtrig-cpu: registered to indicate activity on CPUs [ 0.883435] meson-sm: secure-monitor enabled [ 0.884528] usbcore: registered new interface driver usbhid [ 0.884537] usbhid: USB HID core driver [ 0.885576] platform-mhu c883c404.mailbox: Platform MHU Mailbox registered [ 0.892228] NET: Registered protocol family 17 [ 0.892387] 9pnet: Installing 9P2000 support [ 0.892454] Key type dns_resolver registered [ 0.892872] printk: console [ttyAML0]: printing thread started [ 0.892958] registered taskstats version 1 [ 0.892965] Loading compiled-in X.509 certificates [ 0.911636] meson-gx-mmc d0074000.mmc: no support for card's volts [ 0.911657] mmc1: error -22 whilst initialising SDIO card [ 0.915365] dwc3-meson-g12a d0078080.usb: USB2 ports: 2 [ 0.915382] dwc3-meson-g12a d0078080.usb: USB3 ports: 0 [ 1.439421] dwc2 c9100000.usb: supply vusb_d not found, using dummy regulator [ 1.439652] dwc2 c9100000.usb: supply vusb_a not found, using dummy regulator [ 1.439978] dwc2 c9100000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM [ 1.443570] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.443608] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 1.443771] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f664 hci version 0x100 quirks 0x0000000002010010 [ 1.443839] xhci-hcd xhci-hcd.0.auto: irq 48, io mem 0xc9000000 [ 1.444677] hub 1-0:1.0: USB hub found [ 1.444718] hub 1-0:1.0: 2 ports detected [ 1.444997] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.445013] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 1.445040] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 1.445096] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.445681] hub 2-0:1.0: USB hub found [ 1.445710] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 1.451238] meson-gx-mmc d0072000.mmc: Got CD GPIO [ 1.454460] scpi_protocol scpi: SCP Protocol legacy pre-1.0 firmware [ 1.489158] scpi_clocks scpi:clocks: failed to register clock 'vcpu' [ 1.489206] scpi_clocks: probe of scpi:clocks failed with error -110 [ 1.522087] mmc0: new high speed SDHC card at address aaaa [ 1.523009] mmcblk0: mmc0:aaaa SC16G 14.8 GiB [ 1.525905] mmcblk0: p1 [ 1.701141] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 1.893490] hub 1-1:1.0: USB hub found [ 1.893794] hub 1-1:1.0: 4 ports detected omain-0 init dvfs: 4 [ 13.789295] ALSA device list: [ 13.789309] No soundcards found. [ 13.791931] Freeing unused kernel memory: 5952K [ 13.792030] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [BL31]: tee size: 0 [ 14.291523] gxl-crypto c883e000.crypto: will run requests pump with realtime priority [ 14.291757] gxl-crypto c883e000.crypto: will run requests pump with realtime priority [ 14.300209] meson8b-dwmac c9410000.ethernet: IRQ eth_wake_irq not found [ 14.300229] meson8b-dwmac c9410000.ethernet: IRQ eth_lpi not found [ 14.300365] meson8b-dwmac c9410000.ethernet: PTP uses main clock [ 14.300374] meson8b-dwmac c9410000.ethernet: no reset control found [ 14.311723] meson8b-dwmac c9410000.ethernet: User ID: 0x11, Synopsys ID: 0x37 [ 14.311754] meson8b-dwmac c9410000.ethernet: DWMAC1000 [ 14.311761] meson8b-dwmac c9410000.ethernet: DMA HW capability register supported [ 14.311766] meson8b-dwmac c9410000.ethernet: RX Checksum Offload Engine supported [ 14.311770] meson8b-dwmac c9410000.ethernet: COE Type 2 [ 14.311775] meson8b-dwmac c9410000.ethernet: TX Checksum insertion supported [ 14.311779] meson8b-dwmac c9410000.ethernet: Wake-Up On Lan supported [ 14.311906] meson8b-dwmac c9410000.ethernet: Normal descriptors [ 14.311911] meson8b-dwmac c9410000.ethernet: Ring mode enabled [ 14.311916] meson8b-dwmac c9410000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 14.314517] meson-drm d0100000.vpu: Queued 3 outputs on vpu [ 14.359720] Registered IR keymap rc-empty [ 14.359853] rc rc0: meson-ir as /devices/platform/soc/c8100000.bus/c8100580.ir/rc/rc0 [ 14.359977] input: meson-ir as /devices/platform/soc/c8100000.bus/c8100580.ir/rc/rc0/input0 [ 14.360433] meson-ir c8100580.ir: receiver initialized [ 14.369343] meson-dw-hdmi c883a000.hdmi-tx: Detected HDMI TX controller v2.01a with HDCP (meson_dw_hdmi_phy) [ 14.378684] meson-dw-hdmi c883a000.hdmi-tx: registered DesignWare HDMI I2C bus driver [ 14.380954] meson-drm d0100000.vpu: bound c883a000.hdmi-tx (ops meson_dw_hdmi_ops [meson_dw_hdmi]) [ 14.381854] [drm] Initialized meson 1.0.0 20161109 for d0100000.vpu on minor 0 [ 14.387811] lima d00c0000.gpu: gp - mali450 version major 0 minor 0 [ 14.387880] lima d00c0000.gpu: pp0 - mali450 version major 0 minor 0 [ 14.387923] lima d00c0000.gpu: pp1 - mali450 version major 0 minor 0 [ 14.387968] lima d00c0000.gpu: pp2 - mali450 version major 0 minor 0 [ 14.388009] lima d00c0000.gpu: l2 cache 8K, 4-way, 64byte cache line, 128bit external bus [ 14.388022] lima d00c0000.gpu: l2 cache 64K, 4-way, 64byte cache line, 128bit external bus [ 14.390651] lima d00c0000.gpu: bus rate = 166666667 [ 14.390670] lima d00c0000.gpu: mod rate = 24000000 [ 14.390755] lima d00c0000.gpu: dev_pm_opp_set_regulators: no regulator (mali) found: -19 [ 14.391408] lima d00c0000.gpu: Failed to register cooling device [ 14.391802] [drm] Initialized lima 1.1.0 20191231 for d00c0000.gpu on minor 1 [ 14.407953] Console: switching to colour frame buffer device 90x36 [ 14.432668] meson-drm d0100000.vpu: [drm] fb0: mesondrmfb frame buffer device [ 14.567708] debugfs: Directory 'c1105400.audio-controller' with parent 'GXL-LIBRETECH-S905X-CC' already present! [ 14.567758] debugfs: Directory 'c1105400.audio-controller' with parent 'GXL-LIBRETECH-S905X-CC' already present! Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 66:cf:17:bf:56:f1 mtu 1500 DHCP [ 14.824086] meson8b-dwmac c9410000.ethernet eth0: PHY [0.e40908ff:08] driver [Meson GXL Internal PHY] (irq=49) [ 14.836353] meson8b-dwmac c9410000.ethernet eth0: No Safety Features support found [ 14.836374] meson8b-dwmac c9410000.ethernet eth0: PTP not supported by HW [ 14.836753] meson8b-dwmac c9410000.ethernet eth0: configuring for phy/rmii link mode [ 16.332323] meson8b-dwmac c9410000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx IP-Config: no response after 2 secs - giving up IP-Config: eth0 hardware address 66:cf:17:bf:56:f1 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 10.201.1.3): address: 10.201.3.5 broadcast: 10.201.255.255 netmask: 255.255.0.0 gateway: 10.201.1.3 dns0 : 10.1.1.1 dns1 : 0.0.0.0 rootserver: 10.201.1.3 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 20.489972] systemd[1]: System time before build time, advancing clock. [ 20.642150] NET: Registered protocol family 10 [ 20.643153] Segment Routing with IPv6 [ 20.697061] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 20.697835] systemd[1]: Detected architecture arm64. Welcome to [1mDebian GNU/Linux 11 (bullseye)[0m! [ 20.739530] systemd[1]: Set hostname to . [ 21.522398] systemd[1]: Queued start job for default target Graphical Interface. [ 21.524934] random: systemd: uninitialized urandom read (16 bytes read) [ 21.525288] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 21.525304] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 21.528352] systemd[1]: Created slice system-getty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-getty.slice[0m. [[0;32m OK [0m] Created slice [0;1;39msystem-modprobe.slice[ 21.577326] random: systemd: uninitialized urandom read (16 bytes read) [ 21.578540] systemd[1]: Created slice system-modprobe.slice. [0m. [[0;32m OK [0m] Created slice [0;1;39msystem-serial\x2dgetty[ 21.605340] random: systemd: uninitialized urandom read (16 bytes read) [ 21.606826] systemd[1]: Created slice system-serial\x2dgetty.slice. .slice[0m. [[0;32m OK [0m] Created slice [0;1;39mUser and Session Slice[ 21.634334] systemd[1]: Created slice User and Session Slice. [0m. [[0;32m OK [0m] Started [0;1;39mDispatch Password …ts to Console Directory Watch[0m. [ 21.653659] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [[0;32m OK [0m] Started [0;1;39mForward Password R…uests to Wall Directory Watch[0m. [ 21.677609] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [[0;32m OK [0m] Reached target [0;1;39mLocal Encrypted Volumes[0m. [ 21.701439] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 21.701689] systemd[1]: Reached target Local Encrypted Volumes. [[0;32m OK [0m] Reached target [0;1;39mPaths[0m. [ 21.737510] systemd[1]: Reached target Paths. [[0;32m OK [0m] Reached target [0;1;39mRemote File Systems[0m. [ 21.749366] systemd[1]: Reached target Remote File Systems. [[0;32m OK [0m] Reached target [0;1;39mSlices[0m. [ 21.761349] systemd[1]: Reached target Slices. [[0;32m OK [0m] Reached target [0;1;39mSwap[0m. [ 21.773393] systemd[1]: Reached target Swap. [[0;32m OK [0m] Listening on [0;1;39minitctl Compatibility Named Pipe[0m. [ 21.785739] systemd[1]: Listening on initctl Compatibility Named Pipe. [[0;32m OK [0m] Listening on [0;1;39mJournal Audit Socket[0[ 21.810943] systemd[1]: Listening on Journal Audit Socket. m. [[0;32m OK [0m] Listening on [0;1;39mJournal Socket (/dev/lo[ 21.830740] systemd[1]: Listening on Journal Socket (/dev/log). g)[0m. [[0;32m OK [0m] Listening on [0;1;39mJournal Socket[0m. [ 21.850002] systemd[1]: Listening on Journal Socket. [[0;32m OK [0m] Listening on [0;1;39mNetwork Service Netlink[ 21.862866] systemd[1]: Listening on Network Service Netlink Socket. Socket[0m. [[0;32m OK [0m] Listening on [0;1;39mudev Control Socket[0m. [ 21.885820] systemd[1]: Listening on udev Control Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Kernel Socket[0m. [ 21.909908] systemd[1]: Listening on udev Kernel Socket. Mounting [0;1;39mHuge Pages File System[0m... [ 21.936782] systemd[1]: Mounting Huge Pages File System... Mounting [0;1;39mPOSIX Message Queue File System[0m... [ 21.961641] systemd[1]: Mounting POSIX Message Queue File System... [ 21.989013] systemd[1]: Mounting Kernel Debug File System... Mounting [0;1;39mKernel Debug File System[0m... [ 22.005784] systemd[1]: Condition check resulted in Kernel Trace File System being skipped. [ 22.011795] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting [0;1;39mCreate list of st…odes for the current kernel[0m... Starting [0;1;39mLoad Kernel Module configfs[0m... [ 22.042511] systemd[1]: Starting Load Kernel Module configfs... Starting [0;1;39mLoad Kernel Module drm[0m... [ 22.069274] systemd[1]: Starting Load Kernel Module drm... Starting [0;1;39mLoad Kernel Module fuse[0m... [ 22.087398] systemd[1]: Starting Load Kernel Module fuse... [ 22.116530] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 22.121095] systemd[1]: Starting Journal Service... Starting [0;1;39mJournal Service[0m... [ 22.151915] fuse: init (API version 7.32) Starting [0;1;39mLoad Kernel Modules[0m... [ 22.158396] systemd[1]: Starting Load Kernel Modules... Starting [0;1;39mRemount Root and Kernel File Systems[0m... [ 22.177804] systemd[1]: Starting Remount Root and Kernel File Systems... Starting [0;1;39mColdplug All udev Devices[0m... [ 22.205252] systemd[1]: Starting Coldplug All udev Devices... [[0;32m OK [0m] Mounted [0;1;39mHuge Pages File System[0m.[ 22.222714] systemd[1]: Mounted Huge Pages File System. [[0;32m OK [0m] Mounted [0;1;39mPOSIX Message Queue File System[0m. [ 22.242150] systemd[1]: Mounted POSIX Message Queue File System. [[0;32m OK [0m] Mounted [0;1;39mKernel Debug File System[0m[ 22.262411] systemd[1]: Mounted Kernel Debug File System. . [[0;32m OK [0m] Finished [0;1;39mCreate list of st… nodes [ 22.288024] systemd[1]: Finished Create list of static device nodes for the current kernel. for the current kernel[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module configfs[ 22.310867] systemd[1]: modprobe@configfs.service: Succeeded. [ 22.311885] systemd[1]: Finished Load Kernel Module configfs. [0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module drm[0m.[ 22.338718] systemd[1]: modprobe@drm.service: Succeeded. [ 22.339802] systemd[1]: Finished Load Kernel Module drm. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module fuse[0m[ 22.366688] systemd[1]: modprobe@fuse.service: Succeeded. [ 22.367737] systemd[1]: Finished Load Kernel Module fuse. . [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Modules[0m. [ 22.394841] systemd[1]: Finished Load Kernel Modules. [[0;32m OK [0m] Finished [0;1;39mRemount Root and Kernel Fil[ 22.418814] systemd[1]: Finished Remount Root and Kernel File Systems. e Systems[0m. [[0;32m OK [0m] Started [0;1;39mJournal Service[0m. [ 22.438177] systemd[1]: Started Journal Service. Mounting [0;1;39mFUSE Control File System[0m... Mounting [0;1;39mKernel Configuration File System[0m... Starting [0;1;39mFlush Journal to Persistent Storage[0m... Starting [0;1;39mLoad/Save Random Seed[0m... [ 22.529501] random: systemd: uninitialized urandom read (16 bytes read) [ 22.533982] random: systemd-journal: uninitialized urandom read (16 bytes read) Starting [0;1;39mApply Kernel Variables[0m... [ 22.562510] random: systemd: uninitialized urandom read (16 bytes read) Starting [0;1;39mCreate System Users[0m... [[0;32m OK [0m] Mounted [0;1;39mFUSE Control File System[0m. [ 22.592859] systemd-journald[241]: Received client request to flush runtime journal. [[0;32m OK [0m] Mounted [0;1;39mKernel Configuration File System[0m. [[0;32m OK [0m] Finished [0;1;39mApply Kernel Variables[0m. [[0;32m OK [0m] Finished [0;1;39mColdplug All udev Devices[0m. [ 23.778028] random: systemd-journal: uninitialized urandom read (16 bytes read) [ 24.117134] random: crng init done [ 24.117146] random: 46 urandom warning(s) missed due to ratelimiting [[0m[0;31m* [0m] (1 of 4) A start job is running for…reate System Users (3s / 1min 31s) M[K[[0;1;31m*[0m[0;31m* [0m] (1 of 4) A start job is running for…reate System Users (3s / 1min 31s) M[K[[0;32m OK [0m] Finished [0;1;39mLoad/Save Random Seed[0m. [K[[0;31m*[0;1;31m*[0m[0;31m* [0m] (1 of 3) A start job is running for…reate System Users (5s / 1min 31s) M[K[ [0;31m*[0;1;31m*[0m[0;31m* [0m] (2 of 3) A start job is running for…Persistent Storage (6s / 1min 30s) M[K[ [0;31m*[0;1;31m*[0m[0;31m* [0m] (2 of 3) A start job is running for…Persistent Storage (6s / 1min 30s) M[K[ [0;31m*[0;1;31m*[0m[0;31m*[0m] (2 of 3) A start job is running for…Persistent Storage (7s / 1min 30s) M[K[ [0;31m*[0;1;31m*[0m] (3 of 3) A start job is running for /dev/ttyAML0 (7s / 1min 30s) M[K[ [0;31m*[0m] (3 of 3) A start job is running for /dev/ttyAML0 (8s / 1min 30s) M[K[ [0;31m*[0;1;31m*[0m] (3 of 3) A start job is running for /dev/ttyAML0 (8s / 1min 30s) M[K[ [0;31m*[0;1;31m*[0m[0;31m*[0m] (1 of 3) A start job is running for…reate System Users (9s / 1min 31s) M[K[ [0;31m*[0;1;31m*[0m[0;31m* [0m] (1 of 3) A start job is running for…reate System Users (9s / 1min 31s) M[K[ [0;31m*[0;1;31m*[0m[0;31m* [0m] (1 of 3) A start job is running for…eate System Users (10s / 1min 31s) M[K[[0;31m*[0;1;31m*[0m[0;31m* [0m] (2 of 3) A start job is running for…ersistent Storage (10s / 1min 30s) M[K[[0;1;31m*[0m[0;31m* [0m] (2 of 3) A start job is running for…ersistent Storage (11s / 1min 30s) M[K[[0;32m OK [0m] Finished [0;1;39mFlush Journal to Persistent Storage[0m. [K[[0;32m OK [0m] Finished [0;1;39mCreate System Users[0m. Starting [0;1;39mCreate Static Device Nodes in /dev[0m... [[0;32m OK [0m] Finished [0;1;39mCreate Static Device Nodes in /dev[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems (Pre)[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems[0m. Starting [0;1;39mCreate Volatile Files and Directories[0m... Starting [0;1;39mRule-based Manage…for Device Events and Files[0m... [[0;32m OK [0m] Started [0;1;39mRule-based Manager for Device Events and Files[0m. Starting [0;1;39mNetwork Service[0m... [[0;32m OK [0m] Found device [0;1;39m/dev/ttyAML0[0m. [[0;32m OK [0m] Finished [0;1;39mCreate Volatile Files and Directories[0m. Starting [0;1;39mNetwork Time Synchronization[0m... Starting [0;1;39mUpdate UTMP about System Boot/Shutdown[0m... [[0;32m OK [0m] Started [0;1;39mNetwork Service[0m. [[0;32m OK [0m] Reached target [0;1;39mSound Card[0m. [[0;32m OK [0m] Reached target [0;1;39mHardware activated USB gadget[0m. Starting [0;1;39mNetwork Name Resolution[0m... [[0m[0;31m* [0m] (2 of 3) A start job is running for…tem Boot/Shutdown (17s / no limit) M[K[[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Boot/Shutdown[0m. [K[[0;32m OK [0m] Started [0;1;39mNetwork Time Synchronization[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Initialization[0m. [[0;32m OK [0m] Started [0;1;39mDaily Cleanup of Temporary Directories[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Set[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Synchronized[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt download activities[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt upgrade and clean activities[0m. [[0;32m OK [0m] Started [0;1;39mPeriodic ext4 Onli…ata Check for All Filesystems[0m. [[0;32m OK [0m] Started [0;1;39mDiscard unused blocks once a week[0m. [[0;32m OK [0m] Reached target [0;1;39mTimers[0m. [[0;32m OK [0m] Listening on [0;1;39mD-Bus System Message Bus Socket[0m. [[0;32m OK [0m] Reached target [0;1;39mSockets[0m. [[0;32m OK [0m] Reached target [0;1;39mBasic System[0m. [[0;32m OK [0m] Started [0;1;39mD-Bus System Message Bus[0m. Starting [0;1;39mRemove Stale Onli…t4 Metadata Check Snapshots[0m... Starting [0;1;39mUser Login Management[0m... [[0;32m OK [0m] Started [0;1;39mNetwork Name Resolution[0m. [[0;32m OK [0m] Reached target [0;1;39mNetwork[0m. [[0;32m OK [0m] Reached target [0;1;39mHost and Network Name Lookups[0m. Starting [0;1;39mPermit User Sessions[0m... [[0;32m OK [0m] Finished [0;1;39mRemove Stale Onli…ext4 Metadata Check Snapshots[0m. [[0;32m OK [0m] Finished [0;1;39mPermit User Sessions[0m. [[0;32m OK [0m] Started [0;1;39mGetty on tty1[0m. [[0;32m OK [0m] Started [0;1;39mSerial Getty on ttyAML0[0m. [[0;32m OK [0m] Reached target [0;1;39mLogin Prompts[0m. [[0;32m OK [0m] Started [0;1;39mUser Login Management[0m. [[0;32m OK [0m] Reached target [0;1;39mMulti-User System[0m. [[0;32m OK [0m] Reached target [0;1;39mGraphical Interface[0m. Starting [0;1;39mUpdate UTMP about System Runlevel Changes[0m... [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Runlevel Changes[0m. [ 43.997149] VDDIO_BOOT: disabling Debian GNU/Linux 11 debian-bullseye-arm64 ttyAML0 debian-bullseye-arm64 login: root (automatic login) Linux debian-bullseye-arm64 5.10.162-cip24-rt10 #1 SMP PREEMPT Fri Jan 27 00:52:47 UTC 2023 aarch64 The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/3222361/extract-nfsrootfs-v2dgv7xa' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/3222361/extract-nfsrootfs-v2dgv7xa' / # export NFS_SERVER_IP='10.201.1.11' export NFS_SERVER_IP='10.201.1.11' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-3222361/environment . /lava-3222361/environment / # /lava-3222361/bin/lava-test-runner /lava-3222361/0 /lava-3222361/bin/lava-test-runner /lava-3222361/0 + export TESTRUN_ID=0_dmesg + cd /lava-3222361/0/tests/0_dmesg + cat uuid + UUID=3222361_1.6.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 46.857445] [ 47.361213] [ 47.765995] + set +x [ 48.155509] [ 48.156664] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-3222361/environment / # . /lava-3222361/environment/lava-3222361/bin/lava-test-runner /lava-3222361/1 / # /lava-3222361/bin/lava-test-runner /lava-3222361/1 + export TESTRUN_ID=1_bootrr + cd /lava-3222361/1/tests/1_bootrr + cat uuid + UUID=3222361_1.6.2.4.5 + set +x + export PATH=/opt/bootrr/libexec[ 49.039067] /bootrr/helpers:/lava-3222361/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-3222361/1/../bin/lava-test-case [ 49.299269] /lava-3222361/1/../bin/lava-test-case [ 49.641721] /lava-3222361/1/../bin/lava-test-case [ 49.794576] + set +x [ 49.831177] / #