[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9730064/tftp-deploy-cbasjfjf/kernel/zImage tftp 0x10000000 9730064/tftp-deploy-cbasjfjf/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '9730064/tftp-deploy-cbasjfjf/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 10.6 MiB/s done Bytes transferred = 9703936 (941200 hex) => tftp 0x14000000 9730064/tftp-deploy-cbasjfjf/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9730064/tftp-deploy-cbasjfjf/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '9730064/tftp-deploy-cbasjfjf/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 10.1 MiB/s done Bytes transferred = 12143318 (b94ad6 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9730064/tftp-deploy-cbasjfjf/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9730064/tftp-deploy-cbasjfjf/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '9730064/tftp-deploy-cbasjfjf/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.7 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9730064/extract-nfsrootfs-9abw9nl4,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9730064/extract-nfsrootfs-9abw9nl4,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x941200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12143254 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.175-cip29-rt12 (KernelCI@build-j1227395-arm-gcc-10-multi-v7-defconfig-82khf) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Mar 22 12:47:20 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s33612 r8192 d23732 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9730064/extract-nfsrootfs-9abw9nl4,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 936480K/1048576K available (14336K kernel code, 2330K rwdata, 5348K rodata, 2048K init, 415K bss, 46560K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000018] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.003795] Console: colour dummy device 80x30 [ 0.003846] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.003859] pid_max: default: 32768 minimum: 301 [ 0.004021] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004043] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004676] CPU: Testing write buffer coherency: ok [ 0.004707] CPU0: Spectre v2: using BPIALL workaround [ 0.004964] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005683] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.007287] rcu: Hierarchical SRCU implementation. [ 0.010870] EFI services will not be available. [ 0.011177] smp: Bringing up secondary CPUs ... [ 0.011992] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.012006] CPU1: Spectre v2: using BPIALL workaround [ 0.012916] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.012929] CPU2: Spectre v2: using BPIALL workaround [ 0.013811] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.013824] CPU3: Spectre v2: using BPIALL workaround [ 0.013939] smp: Brought up 1 node, 4 CPUs [ 0.013949] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.013959] CPU: All CPU(s) started in SVC mode. [ 0.014508] devtmpfs: initialized [ 0.021839] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.022076] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.022098] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.025218] pinctrl core: initialized pinctrl subsystem [ 0.027055] DMI not present or invalid. [ 0.027884] NET: Registered protocol family 16 [ 0.031443] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.033764] thermal_sys: Registered thermal governor 'step_wise' [ 0.033943] cpuidle: using governor menu [ 0.034122] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.213114] vdd1p1: supplied by regulator-dummy [ 0.220462] vdd3p0: supplied by regulator-dummy [ 0.227759] vdd2p5: supplied by regulator-dummy [ 0.235114] vddarm: supplied by regulator-dummy [ 0.242601] vddpu: supplied by regulator-dummy [ 0.249779] vddsoc: supplied by regulator-dummy [ 0.586437] No ATAGs? [ 0.586579] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.586590] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.590800] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.596904] Serial: AMBA PL011 UART driver [ 0.599073] printk: console [ramoops-1] enabled [ 0.599319] pstore: Registered ramoops as persistent store backend [ 0.599326] ramoops: using 0x10000@0x30000000, ecc: 0 [ 0.631549] iommu: Default domain type: Translated [ 0.631972] vgaarb: loaded [ 0.632864] SCSI subsystem initialized [ 0.633397] usbcore: registered new interface driver usbfs [ 0.633451] usbcore: registered new interface driver hub [ 0.633492] usbcore: registered new device driver usb [ 0.635031] i2c i2c-0: IMX I2C adapter registered [ 0.636372] i2c i2c-1: IMX I2C adapter registered [ 0.637187] i2c i2c-2: IMX I2C adapter registered [ 0.638495] pps_core: LinuxPPS API ver. 1 registered [ 0.638502] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.638527] PTP clock support registered [ 0.642064] clocksource: Switched to clocksource mxc_timer1 [ 1.792816] NET: Registered protocol family 2 [ 1.793263] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.794419] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.794460] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.794549] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.794689] TCP: Hash tables configured (established 8192 bind 8192) [ 1.794896] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.794940] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.795121] NET: Registered protocol family 1 [ 1.795746] RPC: Registered named UNIX socket transport module. [ 1.795755] RPC: Registered udp transport module. [ 1.795759] RPC: Registered tcp transport module. [ 1.795763] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.795774] PCI: CLS 0 bytes, default 64 [ 1.796253] Trying to unpack rootfs image as initramfs... [ 2.759865] Freeing initrd memory: 11860K [ 2.760317] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 2.760716] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.762616] Initialise system trusted keyrings [ 2.762942] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.768624] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.769372] NFS: Registering the id_resolver key type [ 2.769433] Key type id_resolver registered [ 2.769439] Key type id_legacy registered [ 2.769538] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.769546] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.769581] ntfs: driver 2.1.32 [Flags: R/O]. [ 2.770045] Key type asymmetric registered [ 2.770053] Asymmetric key parser 'x509' registered [ 2.770109] bounce: pool size: 64 pages [ 2.770146] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 2.770154] io scheduler mq-deadline registered [ 2.770160] io scheduler kyber registered [ 2.809829] mxs-dma 110000.dma-apbh: initialized [ 2.814659] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 2.814678] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 2.875564] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.880035] SuperH (H)SCI(F) driver initialized [ 2.880998] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 2.882068] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 2.882110] printk: console [ttymxc1] enabled [ 2.883511] msm_serial: driver initialized [ 2.883777] STMicroelectronics ASC driver initialized [ 2.885719] STM32 USART driver initialized [ 2.896515] panel-simple panel-lcd: supply power not found, using dummy regulator [ 2.896678] panel-simple panel-lcd: Specify missing connector_type [ 2.897074] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 2.905749] brd: module loaded [ 2.915666] loop: module loaded [ 2.919575] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 2.919590] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 2.919599] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 2.919607] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 2.919694] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 2.919847] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 2.919930] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 2.922134] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 2.922162] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 2.922179] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 2.923686] scsi host0: ahci-imx [ 2.924044] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 2.936472] CAN device driver interface [ 2.937767] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.941323] pps pps0: new PPS source ptp0 [ 2.960085] fec 2188000.ethernet eth0: registered PHC device 0 [ 2.961567] e1000e: Intel(R) PRO/1000 Network Driver [ 2.961573] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.961633] igb: Intel(R) Gigabit Ethernet Network Driver [ 2.961638] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.967813] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.967857] usbcore: registered new interface driver pegasus [ 2.967898] usbcore: registered new interface driver asix [ 2.967930] usbcore: registered new interface driver ax88179_178a [ 2.967962] usbcore: registered new interface driver cdc_ether [ 2.968012] usbcore: registered new interface driver smsc75xx [ 2.968057] usbcore: registered new interface driver smsc95xx [ 2.968091] usbcore: registered new interface driver net1080 [ 2.968125] usbcore: registered new interface driver cdc_subset [ 2.968154] usbcore: registered new interface driver zaurus [ 2.968222] usbcore: registered new interface driver cdc_ncm [ 2.971750] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.971757] ehci-pci: EHCI PCI platform driver [ 2.971798] ehci-platform: EHCI generic platform driver [ 2.972121] ehci-orion: EHCI orion driver [ 2.972348] SPEAr-ehci: EHCI SPEAr driver [ 2.972540] ehci-st: EHCI STMicroelectronics driver [ 2.972724] ehci-exynos: EHCI Exynos driver [ 2.972906] ehci-atmel: EHCI Atmel driver [ 2.973094] tegra-ehci: Tegra EHCI driver [ 2.973311] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.973331] ohci-pci: OHCI PCI platform driver [ 2.973373] ohci-platform: OHCI generic platform driver [ 2.973632] SPEAr-ohci: OHCI SPEAr driver [ 2.973821] ohci-st: OHCI STMicroelectronics driver [ 2.974009] ohci-atmel: OHCI Atmel driver [ 2.975055] usbcore: registered new interface driver usb-storage [ 2.983290] i2c /dev entries driver [ 3.003140] sdhci: Secure Digital Host Controller Interface driver [ 3.003148] sdhci: Copyright(c) Pierre Ossman [ 3.005844] Synopsys Designware Multimedia Card Interface Driver [ 3.007803] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.009086] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 3.009129] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 3.010371] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 3.012952] ledtrig-cpu: registered to indicate activity on CPUs [ 3.013914] usbcore: registered new interface driver usbhid [ 3.013921] usbhid: USB HID core driver [ 3.020436] NET: Registered protocol family 10 [ 3.021415] Segment Routing with IPv6 [ 3.021497] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.022108] NET: Registered protocol family 17 [ 3.022126] can: controller area network core [ 3.022199] NET: Registered protocol family 29 [ 3.022207] can: raw protocol [ 3.022215] can: broadcast manager protocol [ 3.022225] can: netlink gateway - max_hops=1 [ 3.022634] Key type dns_resolver registered [ 3.024660] ThumbEE CPU extension supported. [ 3.024675] Registering SWP/SWPB emulation handler [ 3.025188] printk: console [ttymxc1]: printing thread started [ 3.025429] printk: console [ramoops-1]: printing thread started [ 3.025480] Loading compiled-in X.509 certificates [ 3.030623] pstore: Using crash dump compression: deflate [ 3.042563] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 3.043053] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 3.051648] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.051799] panel-simple panel-lcd: Specify missing connector_type [ 3.053406] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.061874] imx_usb 2184200.usb: No over current polarity defined [ 3.065433] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 3.065457] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 3.092046] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 3.092647] hub 1-0:1.0: USB hub found [ 3.092686] hub 1-0:1.0: 1 port detected [ 3.094691] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 3.098964] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.099093] panel-simple panel-lcd: Specify missing connector_type [ 3.100477] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.105137] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.105261] panel-simple panel-lcd: Specify missing connector_type [ 3.106664] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.108636] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.113553] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.113682] panel-simple panel-lcd: Specify missing connector_type [ 3.115085] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.235750] mmc2: new high speed SDHC card at address e624 [ 3.236525] mmcblk2: mmc2:e624 SL16G 14.8 GiB [ 3.259667] ata1: SATA link down (SStatus 0 SControl 300) [ 3.259723] ahci-imx 2200000.sata: no device found, disabling link. [ 3.259730] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 3.274592] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 3.305035] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 3.305041] GPT:29296874 != 31116287 [ 3.305046] GPT:Alternate GPT header not at the end of the disk. [ 3.305048] GPT:29296874 != 31116287 [ 3.305053] GPT: Use GNU Parted to correct GPT errors. [ 3.305089] mmcblk2: p1 p2 p3 [ 3.310247] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.310384] panel-simple panel-lcd: Specify missing connector_type [ 3.311861] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.392039] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 3.627460] hub 1-1:1.0: USB hub found [ 3.634797] hub 1-1:1.0: 3 ports detected [ 3.682342] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.682467] panel-simple panel-lcd: Specify missing connector_type [ 3.683874] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 6.392549] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 6.412115] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.442114] Sending DHCP requests ., OK [ 6.482144] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 [ 6.482168] IP-Config: Complete: [ 6.482174] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 [ 6.482199] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) [ 6.482213] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 6.482228] nameserver0=192.168.201.1 [ 6.490570] Freeing unused kernel memory: 2048K [ 6.533694] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 7.369253] imx-ipuv3 2400000.ipu: IPUv3H probed [ 7.374556] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.374728] panel-simple panel-lcd: Specify missing connector_type [ 7.376313] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.379622] imx-ipuv3 2800000.ipu: IPUv3H probed [ 7.384294] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.384473] panel-simple panel-lcd: Specify missing connector_type [ 7.391944] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.402864] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.403036] panel-simple panel-lcd: Specify missing connector_type [ 7.418365] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.424728] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.424875] panel-simple panel-lcd: Specify missing connector_type [ 7.426454] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.451154] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 7.480218] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.480372] panel-simple panel-lcd: Specify missing connector_type [ 7.481052] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 7.481490] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 7.481583] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 7.482278] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.502249] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 7.502327] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 7.502341] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 7.502770] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 [ 7.507770] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.507942] panel-simple panel-lcd: Specify missing connector_type [ 7.514703] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.554534] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.554638] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.554746] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.554840] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.567471] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.567630] panel-simple panel-lcd: Specify missing connector_type [ 7.574038] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.598875] caam 2100000.crypto: Entropy delay = 3200 [ 7.659692] caam 2100000.crypto: Instantiated RNG4 SH0 [ 7.669608] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 7.669786] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 7.669923] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 7.670046] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 7.720439] caam 2100000.crypto: Instantiated RNG4 SH1 [ 7.720461] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 7.720469] caam 2100000.crypto: job rings = 2, qi = 0 [ 7.728677] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.728767] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.728870] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.728928] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.729183] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 7.733493] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 7.734051] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.734200] panel-simple panel-lcd: Specify missing connector_type [ 7.735697] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.752402] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.752498] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.752631] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.752705] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.794572] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.794767] panel-simple panel-lcd: Specify missing connector_type [ 7.797348] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.804627] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.804689] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.804744] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.804788] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 8.127656] caam algorithms registered in /proc/crypto [ 8.129031] caam 2100000.crypto: registering rng-caam [ 8.134426] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.134583] panel-simple panel-lcd: Specify missing connector_type [ 8.136244] panel-simple panel-lvds0: supply power not found, using dummy regulator Begin: Loading essential drivers [ 8.141257] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) ... [ 8.141330] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) done. [ 8.141395] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) Begin: Running /scripts/init-prem[ 8.141440] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) ount ... done. [ 8.147515] panel-simple panel-lcd: supply power not found, using dummy regulator Begin: Mounting root file system [ 8.147672] panel-simple panel-lcd: Specify missing connector_type ... Begin: Running /scripts/nfs-t[ 8.149348] panel-simple panel-lvds0: supply power not found, using dummy regulator op ... done. [ 8.152583] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) Begin: Running /scripts/nfs-premo[ 8.152643] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) unt ... Waiting up to 60 secs for[ 8.152701] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) any ethernet to become available[ 8.152745] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Device /sys/class/net/eth0 found done. [ 8.311555] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f0:fd mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.37 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-7 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 9.592335] systemd[1]: System time before build time, advancing clock. [ 9.648057] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 9.648802] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 9.715403] systemd[1]: Set hostname to . [ OK ] Created slice[ 10.606552] systemd[1]: Queued start job for default target Graphical Interface. system-getty.slice.[ 10.608634] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 10.608658] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 10.609366] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-modprobe.slice. [ 10.672838] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 10.713420] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice User and Session Slice. [ 10.753120] systemd[1]: Created slice User and Session Slice. [ OK ] Started [0;1[ 10.782880] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. ;39mDispatch Password …ts to Console Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 10.822462] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ 10.852898] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 10.853377] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Paths. [ 10.882562] systemd[1]: Reached target Paths. [ OK ] Reached target Remote File Systems. [ 10.912543] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Slices. [ 10.925255] systemd[1]: Reached target Slices. [ OK ] Reached target Swap. [ 10.952335] systemd[1]: Reached target Swap. [ OK ] Listening on initctl Compatibility Named Pipe. [ 10.983433] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on [ 11.047547] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. Journal Socket (/dev/log[ 11.049404] systemd[1]: Listening on Journal Socket (/dev/log). ). [ OK ] Listening on Journal Socket. [ 11.092935] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Network Service Netlink Socket. [ 11.124572] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on udev Control Socket. [ 11.155508] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. [ 11.183618] systemd[1]: Listening on udev Kernel Socket. Mounting Kernel[ 11.213470] systemd[1]: Condition check resulted in Huge Pages File System being skipped. Debug File System... [ 11.214395] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 11.220487] systemd[1]: Mounting Kernel Debug File System... [ 11.247376] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... Starting Create list of st…odes for the current kernel... [ 11.292393] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Load Kernel Module configfs... [ 11.326743] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module drm... [ 11.355886] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module fuse... [ 11.385967] systemd[1]: Starting Load Kernel Module fuse... Starting Journa[ 11.416242] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. l Service... [ 11.420095] systemd[1]: Starting Journal Service... Starting Load K[ 11.469337] systemd[1]: Starting Load Kernel Modules... ernel Modules... Starting Remount Root and Kernel File Systems... [ 11.505903] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Coldplug All udev Devices... [ 11.536131] systemd[1]: Starting Coldplug All udev Devices... [ OK ] Mounted Kernel Debug File System[0[ 11.567190] systemd[1]: Mounted Kernel Debug File System. m. [ OK ] Mounted Kernel Trace File System. [ 11.603152] systemd[1]: Mounted Kernel Trace File System. [ OK ] Finished Create list of st… nodes for the current kernel. [ 11.633287] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Load Kernel Module configfs. [ 11.683554] systemd[1]: modprobe@configfs.service: Succeeded. [ 11.684263] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ 11.713532] systemd[1]: modprobe@drm.service: Succeeded. [ 11.714245] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ 11.743487] systemd[1]: modprobe@fuse.service: Succeeded. [ 11.744180] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Started Journal Service. [ 11.772678] systemd[1]: Started Journal Service. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... [ 12.010142] systemd-journald[287]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.175-cip29-rt12 #1 SMP Wed Mar 22 12:47:20 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9730064/extract-nfsrootfs-9abw9nl4' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9730064/extract-nfsrootfs-9abw9nl4' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-9730064/environment . /lava-9730064/environment / # /lava-9730064/bin/lava-test-runner /lava-9730064/0 /lava-9730064/bin/lava-test-runner /lava-9730064/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-9730064/0/tests/0_timesync-off ++ cat uuid + UUID=9730064_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-9730064/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=9730064_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip/linux-5.10.y-cip-rt/v5.10.175-cip29-rt12/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S skipfile-lkft.yaml -b imx6q-sabrelite -g cip -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: Generating a skipfile based on /lava-9730064/0/tests/1_kselftest-filesystems/automated/linux/kselftest/skipfile-lkft.yaml INFO: Using the following generated skipfile contents (until EOF): breakpoints:breakpoint_test breakpoints:step_after_suspend_test net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait INFO: EOF INFO: install_deps skipped --2023-03-22 13:04:12-- http://storage.kernelci.org/cip/linux-5.10.y-cip-rt/v5.10.175-cip29-rt12/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 52.250.1.28 Connecting to storage.kernelci.org (storage.kernelci.org)|52.250.1.28|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1409152 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 2%[ ] 27.53K 65.9KB/s kselftest.tar.xz 3%[ ] 48.74K 58.3KB/s kselftest.tar.xz 4%[ ] 63.36K 56.8KB/s kselftest.tar.xz 5%[> ] 77.50K 55.6KB/s kselftest.tar.xz 6%[> ] 90.23K 55.7KB/s kselftest.tar.xz 7%[> ] 104.37K 56.3KB/s kselftest.tar.xz 8%[> ] 121.34K 58.1KB/s kselftest.tar.xz 10%[=> ] 138.31K 59.7KB/s kselftest.tar.xz 11%[=> ] 158.10K 62.0KB/s kselftest.tar.xz 12%[=> ] 176.00K 62.2KB/s kselftest.tar.xz 14%[=> ] 200.53K 65.4KB/s eta 18s kselftest.tar.xz 15%[==> ] 216.08K 65.6KB/s eta 18s kselftest.tar.xz 17%[==> ] 246.71K 66.5KB/s eta 18s kselftest.tar.xz 19%[==> ] 272.64K 67.7KB/s eta 18s kselftest.tar.xz 22%[===> ] 304.68K 70.5KB/s eta 15s kselftest.tar.xz 23%[===> ] 325.89K 70.1KB/s eta 15s kselftest.tar.xz 25%[====> ] 347.59K 71.7KB/s eta 15s kselftest.tar.xz 26%[====> ] 370.21K 74.4KB/s eta 15s kselftest.tar.xz 29%[====> ] 400.84K 76.4KB/s eta 14s kselftest.tar.xz 31%[=====> ] 429.60K 78.0KB/s eta 14s kselftest.tar.xz 32%[=====> ] 453.64K 80.7KB/s eta 14s kselftest.tar.xz 35%[======> ] 481.92K 82.8KB/s eta 14s kselftest.tar.xz 37%[======> ] 510.21K 84.1KB/s eta 11s kselftest.tar.xz 39%[======> ] 541.32K 85.9KB/s eta 11s kselftest.tar.xz 40%[=======> ] 562.04K 86.6KB/s eta 11s kselftest.tar.xz 43%[=======> ] 598.81K 86.0KB/s eta 10s kselftest.tar.xz 44%[=======> ] 617.67K 84.5KB/s eta 10s kselftest.tar.xz 46%[========> ] 640.30K 85.3KB/s eta 10s kselftest.tar.xz 47%[========> ] 658.68K 83.4KB/s eta 10s kselftest.tar.xz 50%[=========> ] 688.38K 84.4KB/s eta 9s kselftest.tar.xz 51%[=========> ] 708.17K 83.4KB/s eta 9s kselftest.tar.xz 52%[=========> ] 723.73K 83.9KB/s eta 9s kselftest.tar.xz 53%[=========> ] 738.80K 82.8KB/s eta 9s kselftest.tar.xz 54%[=========> ] 753.42K 81.3KB/s eta 9s kselftest.tar.xz 56%[==========> ] 774.64K 82.0KB/s eta 8s kselftest.tar.xz 57%[==========> ] 793.95K 79.8KB/s eta 8s kselftest.tar.xz 58%[==========> ] 805.75K 77.5KB/s eta 8s kselftest.tar.xz 59%[==========> ] 821.30K 76.6KB/s eta 8s kselftest.tar.xz 61%[===========> ] 841.10K 74.1KB/s eta 7s kselftest.tar.xz 63%[===========> ] 867.48K 71.4KB/s eta 7s kselftest.tar.xz 64%[===========> ] 890.59K 70.1KB/s eta 7s kselftest.tar.xz 65%[============> ] 904.73K 68.1KB/s eta 6s kselftest.tar.xz 66%[============> ] 914.63K 65.2KB/s eta 6s kselftest.tar.xz 67%[============> ] 924.53K 64.7KB/s eta 6s kselftest.tar.xz 68%[============> ] 938.67K 62.9KB/s eta 6s kselftest.tar.xz 69%[============> ] 955.64K 62.6KB/s eta 6s kselftest.tar.xz 70%[=============> ] 975.43K 60.8KB/s eta 6s kselftest.tar.xz 71%[=============> ] 990.50K 59.4KB/s eta 6s kselftest.tar.xz 73%[=============> ] 1008K 57.9KB/s eta 6s kselftest.tar.xz 74%[=============> ] 1023K 58.2KB/s eta 5s kselftest.tar.xz 75%[==============> ] 1.01M 57.9KB/s eta 5s kselftest.tar.xz 76%[==============> ] 1.02M 55.6KB/s eta 5s kselftest.tar.xz 77%[==============> ] 1.04M 55.5KB/s eta 5s kselftest.tar.xz 78%[==============> ] 1.06M 56.0KB/s eta 4s kselftest.tar.xz 79%[==============> ] 1.07M 56.3KB/s eta 4s kselftest.tar.xz 81%[===============> ] 1.09M 57.5KB/s eta 4s kselftest.tar.xz 82%[===============> ] 1.11M 58.6KB/s eta 4s kselftest.tar.xz 83%[===============> ] 1.13M 58.4KB/s eta 4s kselftest.tar.xz 85%[================> ] 1.15M 61.0KB/s eta 3s kselftest.tar.xz 86%[================> ] 1.16M 61.9KB/s eta 3s kselftest.tar.xz 87%[================> ] 1.18M 64.4KB/s eta 3s kselftest.tar.xz 90%[=================> ] 1.21M 66.4KB/s eta 3s kselftest.tar.xz 92%[=================> ] 1.24M 67.8KB/s eta 2s kselftest.tar.xz 93%[=================> ] 1.26M 69.7KB/s eta 2s kselftest.tar.xz 95%[==================> ] 1.28M 71.5KB/s eta 2s kselftest.tar.xz 96%[==================> ] 1.30M 72.7KB/s eta 2s kselftest.tar.xz 98%[==================> ] 1.33M 78.1KB/s eta 2s kselftest.tar.xz 100%[===================>] 1.34M 79.6KB/s in 19s 2023-03-22 13:04:31 (72.3 KB/s) - 'kselftest.tar.xz' saved [1409152/1409152] skiplist: ======================================== breakpoints:breakpoint_test breakpoints:step_after_suspend_test net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait ======================================== filesystems:devpts_pts ============== Tests to run =============== filesystems:devpts_pts ===========End Tests to run =============== [ 51.021028] kselftest: Running tests in filesystems TAP version 13 1..1 # selftests: filesystems: devpts_pts # Failed to perform TIOCGPTPEER ioctl ok 1 selftests: filesystems: devpts_pts filesystems_devpts_pts pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #