Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.9 (4 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 936509/tftp-deploy-02mdkxu1/kernel/zImage tftp 0x82000000 936509/tftp-deploy-02mdkxu1/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '936509/tftp-deploy-02mdkxu1/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 5.2 MiB/s done Bytes transferred = 4607144 (464ca8 hex) => tftp 0x83000000 936509/tftp-deploy-02mdkxu1/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 936509/tftp-deploy-02mdkxu1/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '936509/tftp-deploy-02mdkxu1/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 5.3 MiB/s done Bytes transferred = 10239893 (9c3f95 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 936509/tftp-deploy-02mdkxu1/dtb/am335x-boneblack.dtb tftp 0x88000000 936509/tftp-deploy-02mdkxu1/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '936509/tftp-deploy-02mdkxu1/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.6 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/936509/extract-nfsrootfs-lxjxb4wo,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/936509/extract-nfsrootfs-lxjxb4wo,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-05-18 21:57:56 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 10239829 Bytes = 9.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.179-cip32-rt13 (KernelCI@build-j1529127-arm-gcc-10-omap2plus-defconfig-wwq5h) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu May 18 21:43:08 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] On node 0 totalpages: 130560 [ 0.000000] Normal zone: 1148 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 130560 pages, LIFO batch:31 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 16 pages/cpu s33484 r8192 d23860 u65536 [ 0.000000] pcpu-alloc: s33484 r8192 d23860 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/936509/extract-nfsrootfs-lxjxb4wo,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 475876K/522240K available (9216K kernel code, 1043K rwdata, 2176K rodata, 1024K init, 268K bss, 29980K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008339] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018546] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030223] Console: colour dummy device 80x30 <3>[ 0.035103] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042161] This ensures that you still see kernel messages. Please <3>[ 0.048886] update your kernel commandline. <6>[ 0.053491] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095552] pid_max: default: 32768 minimum: 301 <6>[ 0.100722] LSM: Security Framework initializing <6>[ 0.105832] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.113653] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.122928] CPU: Testing write buffer coherency: ok <6>[ 0.128288] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.134208] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140727] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147942] rcu: Hierarchical SRCU implementation. <6>[ 0.153754] smp: Bringing up secondary CPUs ... <6>[ 0.158690] smp: Brought up 1 node, 1 CPU <6>[ 0.163130] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169874] CPU: All CPU(s) started in SVC mode. <6>[ 0.175622] devtmpfs: initialized <6>[ 0.191343] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199877] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210319] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218963] pinctrl core: initialized pinctrl subsystem <6>[ 0.226524] NET: Registered protocol family 16 <6>[ 0.234169] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260629] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266713] audit: initializing netlink subsys (disabled) <6>[ 0.273808] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273821] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.273825] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.274087] cpuidle: using governor menu <5>[ 1.191253] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.319368] No ATAGs? <6>[ 1.321999] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.346602] Kprobes globally optimized <7>[ 1.357043] reg-fixed-voltage fixedregulator0: GPIO lookup for consumer (null) <7>[ 1.364899] reg-fixed-voltage fixedregulator0: using device tree for GPIO lookup <7>[ 1.372823] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/fixedregulator0[0]' <7>[ 1.382174] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator0[0]' <7>[ 1.391418] reg-fixed-voltage fixedregulator0: using lookup tables for GPIO lookup <7>[ 1.399491] reg-fixed-voltage fixedregulator0: No GPIO consumer (null) found <6>[ 1.409801] iommu: Default domain type: Translated <6>[ 1.416817] vgaarb: loaded <5>[ 1.420513] SCSI subsystem initialized <7>[ 1.425288] libata version 3.00 loaded. <6>[ 1.430140] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.435524] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.445267] PTP clock support registered <6>[ 1.450853] clocksource: Switched to clocksource dmtimer <5>[ 2.060500] VFS: Disk quotas dquot_6.6.0 <6>[ 2.065017] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.082212] NET: Registered protocol family 2 <6>[ 2.087289] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.095989] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.104952] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.113249] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.120932] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.127853] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.134883] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.142503] NET: Registered protocol family 1 <6>[ 2.148323] RPC: Registered named UNIX socket transport module. <6>[ 2.154786] RPC: Registered udp transport module. <6>[ 2.159893] RPC: Registered tcp transport module. <6>[ 2.165019] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.171946] PCI: CLS 0 bytes, default 64 <6>[ 2.176965] Trying to unpack rootfs image as initramfs... <6>[ 2.852189] Freeing initrd memory: 10000K <6>[ 2.857806] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 2.868207] Initialise system trusted keyrings <6>[ 2.873622] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 2.881964] NFS: Registering the id_resolver key type <5>[ 2.887525] Key type id_resolver registered <5>[ 2.892177] Key type id_legacy registered <6>[ 2.896624] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 2.904616] Key type asymmetric registered <5>[ 2.909110] Asymmetric key parser 'x509' registered <6>[ 2.914454] io scheduler mq-deadline registered <6>[ 2.919386] io scheduler kyber registered <3>[ 3.061312] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.069947] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.181690] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.224514] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.297822] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.306554] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.367615] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.376312] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.394028] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.402710] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.467397] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.475967] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.503313] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <7>[ 3.512262] gpio-clk clk_mcasp0: GPIO lookup for consumer enable <7>[ 3.518735] gpio-clk clk_mcasp0: using device tree for GPIO lookup <7>[ 3.525478] gpio-clk clk_mcasp0: No GPIO consumer enable found <6>[ 3.537368] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <7>[ 3.548182] omap8250 44e09000.serial: GPIO lookup for consumer rs485-term <7>[ 3.555595] omap8250 44e09000.serial: using device tree for GPIO lookup <7>[ 3.562720] of_get_named_gpiod_flags: can't parse 'rs485-term-gpios' property of node '/ocp/interconnect@44c00000/segment@200000/target-module@9000/serial@0[0]' <7>[ 3.577807] of_get_named_gpiod_flags: can't parse 'rs485-term-gpio' property of node '/ocp/interconnect@44c00000/segment@200000/target-module@9000/serial@0[0]' <7>[ 3.592793] omap8250 44e09000.serial: using lookup tables for GPIO lookup <7>[ 3.600049] omap8250 44e09000.serial: No GPIO consumer rs485-term found <6>[ 3.607180] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.616604] printk: console [ttyS0] enabled <6>[ 3.616604] printk: console [ttyS0] enabled <6>[ 3.625669] printk: bootconsole [omap8250] disabled <6>[ 3.625669] printk: bootconsole [omap8250] disabled <6>[ 3.649569] brd: module loaded <6>[ 3.661970] loop: module loaded <3>[ 3.667418] mtdoops: mtd device (mtddev=name/number) must be supplied <7>[ 3.676549] mdio_bus fixed-0: GPIO lookup for consumer reset <7>[ 3.682598] mdio_bus fixed-0: using lookup tables for GPIO lookup <7>[ 3.688990] mdio_bus fixed-0: No GPIO consumer reset found <7>[ 3.699286] mdio_bus 4a101000.mdio: GPIO lookup for consumer reset <7>[ 3.705897] mdio_bus 4a101000.mdio: using device tree for GPIO lookup <7>[ 3.712669] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000[0]' <7>[ 3.727743] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000[0]' <7>[ 3.742745] mdio_bus 4a101000.mdio: using lookup tables for GPIO lookup <7>[ 3.749654] mdio_bus 4a101000.mdio: No GPIO consumer reset found <6>[ 3.810815] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <7>[ 3.834696] mdio_bus 4a101000.mdio:00: GPIO lookup for consumer reset <7>[ 3.841605] mdio_bus 4a101000.mdio:00: using device tree for GPIO lookup <7>[ 3.848623] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000/ethernet-phy@0[0]' <7>[ 3.865046] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000/ethernet-phy@0[0]' <7>[ 3.881345] mdio_bus 4a101000.mdio:00: using lookup tables for GPIO lookup <7>[ 3.888517] mdio_bus 4a101000.mdio:00: No GPIO consumer reset found <6>[ 3.896346] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 3.906262] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 3.912982] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 3.918738] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 3.926346] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 3.935382] i2c /dev entries driver <5>[ 3.940991] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 3.948844] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.955396] sdhci: Copyright(c) Pierre Ossman <6>[ 3.960788] sdhci-pltfm: SDHCI platform and OF driver helper <7>[ 3.967798] sdhci-omap 48060000.mmc: GPIO lookup for consumer cd <7>[ 3.974222] sdhci-omap 48060000.mmc: using device tree for GPIO lookup <7>[ 3.981096] sdhci-omap 48060000.mmc: No GPIO consumer cd found <7>[ 3.988109] sdhci-omap 481d8000.mmc: GPIO lookup for consumer wp <7>[ 3.994512] sdhci-omap 481d8000.mmc: using device tree for GPIO lookup <7>[ 4.001367] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/interconnect@48000000/segment@100000/target-module@d8000/mmc@0[0]' <7>[ 4.015230] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/interconnect@48000000/segment@100000/target-module@d8000/mmc@0[0]' <7>[ 4.029010] sdhci-omap 481d8000.mmc: using lookup tables for GPIO lookup <7>[ 4.036028] sdhci-omap 481d8000.mmc: No GPIO consumer wp found <4>[ 4.042337] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.050921] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.059221] Initializing XFRM netlink socket <6>[ 4.064056] NET: Registered protocol family 10 <6>[ 4.071986] Segment Routing with IPv6 <6>[ 4.076040] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.083098] NET: Registered protocol family 17 <6>[ 4.087866] NET: Registered protocol family 15 <5>[ 4.092783] Key type dns_resolver registered <6>[ 4.097940] oprofile: using arm/armv7 <6>[ 4.102060] ThumbEE CPU extension supported. <5>[ 4.106644] Registering SWP/SWPB emulation handler <3>[ 4.112147] omap_voltage_late_init: Voltage driver support not added <3>[ 4.118818] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.127256] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.135957] SmartReflex Class3 initialized <6>[ 4.141596] printk: console [ttyS0]: printing thread started <5>[ 4.141681] Loading compiled-in X.509 certificates <6>[ 4.159224] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <6>[ 4.161181] OMAP GPIO hardware version 0.1 <4>[ 4.211514] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.218945] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.233636] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.234411] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.238389] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.243650] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.243661] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.243917] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.291870] mmc1: new high speed MMC card at address 0001 <6>[ 4.292949] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.293369] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 4.293763] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 4.294110] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (249:0) <6>[ 4.296169] mmcblk1: p1 <6>[ 4.334852] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.336380] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.412357] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 7.571485] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 7.590825] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.620960] Sending DHCP requests ., OK <6>[ 7.660799] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.9 <6>[ 7.660819] IP-Config: Complete: <6>[ 7.660823] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.9, mask=255.255.255.0, gw=192.168.11.1 <6>[ 7.660837] host=192.168.11.9, domain=usen.ad.jp, nis-domain=(none) <6>[ 7.660843] bootserver=0.0.0.0, rootserver=192.168.11.5, rootpath= <6>[ 7.660850] nameserver0=192.168.11.1 <6>[ 7.663487] Freeing unused kernel memory: 1024K <6>[ 7.721300] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <3>[ 8.857275] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <4>[ 8.907870] at24 0-0050: supply vcc not found, using dummy regulator <3>[ 8.952534] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 8.991278] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 8.991775] at24 2-0054: supply vcc not found, using dummy regulator <4>[ 8.995050] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <6>[ 9.006880] remoteproc remoteproc0: wkup_m3 is available <6>[ 9.008524] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <4>[ 9.025226] at24 2-0055: supply vcc not found, using dummy regulator <6>[ 9.026819] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <4>[ 9.118585] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 9.140047] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 9.140387] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 9.152850] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 9.176579] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 9.176674] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <3>[ 9.296540] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 9.331027] usbcore: registered new interface driver usbfs <6>[ 9.331102] usbcore: registered new interface driver hub <6>[ 9.331213] usbcore: registered new device driver usb <4>[ 9.357997] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 9.358315] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <3>[ 9.389899] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 9.420965] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 9.437335] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 9.481050] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.481101] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <3>[ 9.551174] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 9.554004] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 9.554021] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.554030] usb usb1: Product: MUSB HDRC host driver <6>[ 9.554038] usb usb1: Manufacturer: Linux 5.10.179-cip32-rt13 musb-hcd <6>[ 9.554045] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 9.554980] hub 1-0:1.0: USB hub found <6>[ 9.555057] hub 1-0:1.0: 1 port detected <3>[ 9.556288] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 9.563379] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 9.575623] tda998x 0-0070: found TDA19988 <3>[ 9.592548] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 9.629505] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <3>[ 9.776961] davinci-mcasp 48038000.mcasp: IRQ common not found <6>[ 9.779240] remoteproc remoteproc0: powering up wkup_m3 <4>[ 9.779396] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 9.779415] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 9.779423] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 10.139984] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 10.141213] random: crng init done <6>[ 10.192581] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 10.202556] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 10.202935] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 10.205479] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 10.468844] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <3>[ 10.473651] PM: Cannot get wkup_m3_ipc handle <6>[ 10.528139] omap-sham 53100000.sham: will run requests pump with realtime priority <6>[ 10.550049] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 10.598185] omap-aes 53500000.aes: will run requests pump with realtime priority <3>[ 10.640287] PM: Cannot get wkup_m3_ipc handle <3>[ 11.304634] PM: Cannot get wkup_m3_ipc handle <3>[ 11.325797] PM: Cannot get wkup_m3_ipc handle Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 64:cf:d9:3f:a0:d5 mtu 1500 DHCP IP-Config: eth0 guessed broadcast address 192.168.11.255 IP-Config: eth0 complete (dhcp from 192.168.11.1): address: 192.168.11.9 broadcast: 192.168.11.255 netmask: 255.255.255.0 gateway: 192.168.11.1 dns0 : 192.168.11.1 dns1 : 0.0.0.0 domain : usen.ad.jp rootserver: 192.168.11.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 12.712054] systemd[1]: System time before build time, advancing clock. <30>[ 12.804602] systemd[1]: Inserted module 'autofs4' <30>[ 12.847793] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 12.848620] systemd[1]: Detected architecture arm. Welcome to [1mDebian GNU/Linux 11 (bullseye)[0m! <30>[ 12.924282] systemd[1]: Set hostname to . <30>[ 14.734356] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 14.737310] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 14.737358] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [[0;32m OK [0m] Created slice [0;1;39msystem-getty.slice[0m. [[0;32m OK [0m] Created slice [0;1;39msystem-modprobe.slice<30>[ 14.774282] systemd[1]: Created slice system-getty.slice. [0m. <30>[ 14.783709] systemd[1]: Created slice system-modprobe.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-serial\x2dgetty.slice[0m. <30>[ 14.804796] systemd[1]: Created slice system-serial\x2dgetty.slice. [[0;32m OK [0m] Created slice [0;1;39mUser and Session Slice[0m. <30>[ 14.843789] systemd[1]: Created slice User and Session Slice. [[0;32m OK [0m] Started [0;1;39mDispatch Password …ts to Console Directory Watch[0m. <30>[ 14.873072] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [[0;32m OK [0m] Started [0;1;39mForward Password R…uests to Wall Directory Watch[0m. <30>[ 14.902041] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [[0;32m OK [0m] Set up automount [0;1;39mArbitrary…s File System Automount Point[0m. <30>[ 14.933176] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [[0;32m OK [0m] Reached target [0;1;39mLocal Encrypted Volumes[0m. <30>[ 14.961730] systemd[1]: Reached target Local Encrypted Volumes. [[0;32m OK [0m] Reached target [0;1;39mPaths[0m. <30>[ 14.991848] systemd[1]: Reached target Paths. [[0;32m OK [0m] Reached target [0;1;39mRemote File Systems[0m. <30>[ 15.021363] systemd[1]: Reached target Remote File Systems. [[0;32m OK [0m] Reached target [0;1;39mSlices[0m. <30>[ 15.051578] systemd[1]: Reached target Slices. [[0;32m OK [0m] Reached target [0;1;39mSwap[0m. <30>[ 15.081489] systemd[1]: Reached target Swap. [[0;32m OK [0m] Listening on [0;1;39minitctl Compatibility Named Pipe[0m. <30>[ 15.112436] systemd[1]: Listening on initctl Compatibility Named Pipe. [[0;32m OK [0m] Listening on [0;1;39mJournal Audit Socket[<30>[ 15.145415] systemd[1]: Listening on Journal Audit Socket. 0m. [[0;32m OK [0m] Listening on [0;1;39mJournal Socket (/dev/log)[0m. <30>[ 15.183977] systemd[1]: Listening on Journal Socket (/dev/log). [[0;32m OK [0m] Listening on [0;1;39mJournal Socket[0m. <30>[ 15.212980] systemd[1]: Listening on Journal Socket. [[0;32m OK [0m] Listening on [0;1;39mNetwork Service Netlin<30>[ 15.246629] systemd[1]: Listening on Network Service Netlink Socket. k Socket[0m. [[0;32m OK [0m] Listening on [0;1;39mudev Control Socket[0<30>[ 15.287570] systemd[1]: Listening on udev Control Socket. m. [[0;32m OK [0m] Listening on [0;1;39mudev Kernel Socket[0m. <30>[ 15.322693] systemd[1]: Listening on udev Kernel Socket. <30>[ 15.352715] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 15.360414] systemd[1]: Mounting POSIX Message Queue File System... Mounting [0;1;39mPOSIX Message Queue File System[0m... Mounting [0;1;39mKernel Debug File System[0m...<30>[ 15.417202] systemd[1]: Mounting Kernel Debug File System... <30>[ 15.491540] systemd[1]: Mounting Kernel Trace File System... Mounting [0;1;39mKernel Trace File System[0m... Starting [0;1;39mCreate list of st…odes for the curr<30>[ 15.566503] systemd[1]: Starting Create list of static device nodes for the current kernel... ent kernel[0m... Starting [0;1;39mLoad Kernel Module configfs[0m...<30>[ 15.617901] systemd[1]: Starting Load Kernel Module configfs... Starting [0;1;39mLoad Kernel Module drm[0m... <30>[ 15.682083] systemd[1]: Starting Load Kernel Module drm... Starting [0;1;39mLoad Kernel Module fuse[0m... <30>[ 15.731974] systemd[1]: Starting Load Kernel Module fuse... <30>[ 15.773399] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. Starting [0;1;39mJournal Service[0m...<30>[ 15.818214] systemd[1]: Starting Journal Service... Starting [0;1;39mLoad Kernel Modules[0m... <30>[ 15.874551] systemd[1]: Starting Load Kernel Modules... Starting [0;1;39mRemount Root and Kernel File Systems<30>[ 15.907367] systemd[1]: Starting Remount Root and Kernel File Systems... [0m... Starting [0;1;39mColdplug All udev Devices[0m... <30>[ 15.965210] systemd[1]: Starting Coldplug All udev Devices... [[0;32m OK [0m] Mounted [0;1;39mPOSIX Message Queue File Sy<30>[ 16.026180] systemd[1]: Mounted POSIX Message Queue File System. stem[0m. [[0;32m OK [0m] Mounted [0;1;39mKernel Debug File System[0m. <30>[ 16.054178] systemd[1]: Mounted Kernel Debug File System. [[0;32m OK [0m] Mounted [0;1;39mKernel Trace File System[0m. <30>[ 16.070513] systemd[1]: Mounted Kernel Trace File System. [[0;32m OK [0m] Finished [0;1;39mCreate list of st… nodes for the current kernel[0m. <30>[ 16.125723] systemd[1]: Finished Create list of static device nodes for the current kernel. <30>[ 16.146865] systemd[1]: modprobe@configfs.service: Succeeded. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module configfs[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module drm[0m<30>[ 16.188383] systemd[1]: Finished Load Kernel Module configfs. . <30>[ 16.224373] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 16.261244] systemd[1]: Finished Load Kernel Module drm. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module fuse[0m. Mounting [0;1;39mKernel Configuration File System[0m... <30>[ 16.288408] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 16.299856] systemd[1]: Finished Load Kernel Module fuse. <30>[ 16.333269] systemd[1]: Condition check resulted in FUSE Control File System being skipped. <30>[ 16.371693] systemd[1]: Mounting Kernel Configuration File System... [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Modules[0m. Starting [0;1;39mApply Kernel Variables[0m... [[0;32m OK [0m] Finished [0;1;39mRemount Root and Kernel File Systems[0m. <30>[ 16.464829] systemd[1]: Finished Load Kernel Modules. <30>[ 16.513516] systemd[1]: Starting Apply Kernel Variables... <30>[ 16.539520] systemd[1]: Finished Remount Root and Kernel File Systems. [[0;32m OK [0m] Mounted [0;1;39mKernel Configuration File System[0m. <30>[ 16.575047] systemd[1]: Mounted Kernel Configuration File System. <30>[ 16.608025] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. <30>[ 16.608577] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. Starting [0;1;39mLoad/Save Random Seed[0m... Starting [0;1;39mCreate System Users[0m... <30>[ 16.666003] systemd[1]: Starting Load/Save Random Seed... <30>[ 16.736922] systemd[1]: Starting Create System Users... [[0;32m OK [0m] Finished [0;1;39mApply Kernel Variables[0m. <30>[ 17.001996] systemd[1]: Finished Apply Kernel Variables. [[0;32m OK [0m] Finished [0;1;39mLoad/Save Random Seed[0m. <30>[ 17.101925] systemd[1]: Finished Load/Save Random Seed. <30>[ 17.132627] systemd[1]: Condition check resulted in First Boot Complete being skipped. [[0;32m OK [0m] Finished [0;1;39mCreate System Users[0m. <30>[ 17.381699] systemd[1]: Finished Create System Users. Starting [0;1;39mCreate Static Device Nodes in /dev[0<30>[ 17.418106] systemd[1]: Starting Create Static Device Nodes in /dev... m... [[0;32m OK [0m] Finished [0;1;39mCreate Static Device Nodes<30>[ 17.857442] systemd[1]: Finished Create Static Device Nodes in /dev. in /dev[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems (Pre)[0m. <30>[ 17.892358] systemd[1]: Reached target Local File Systems (Pre). [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems[0m. <30>[ 17.921460] systemd[1]: Reached target Local File Systems. Starting [0;1;39mRule-based Manage…for Device Events<30>[ 17.951668] systemd[1]: Condition check resulted in Store a System Token in an EFI Variable being skipped. and Files[0m... <30>[ 17.952028] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped. <30>[ 17.957802] systemd[1]: Starting Rule-based Manager for Device Events and Files... [[0;32m OK [0m] Started [0;1;39mRule-based Manager for Devi<30>[ 18.600030] systemd[1]: Started Rule-based Manager for Device Events and Files. ce Events and Files[0m. [[0;32m OK [0m] Started [0;1;39mJournal Service[0m. <30>[ 18.642507] systemd[1]: Started Journal Service. Starting [0;1;39mFlush Journal to Persistent Storage[0m... Starting [0;1;39mNetwork Service[0m... [[0;32m OK [0m] Finished [0;1;39mColdplug All udev Devices[0m. <46>[ 19.346143] systemd-journald[172]: Received client request to flush runtime journal. [[0m[0;31m* [0m] (1 of 3) A start job is running for /dev/ttyS0 (6s / 1min 30s) M[K[[0;32m OK [0m] Found device [0;1;39m/dev/ttyS0[0m. [K[[0;32m OK [0m] Reached target [0;1;39mHardware activated USB gadget[0m. [[0;32m OK [0m] Finished [0;1;39mFlush Journal to Persistent Storage[0m. Starting [0;1;39mCreate Volatile Files and Directories[0m... [[0;32m OK [0m] Started [0;1;39mNetwork Service[0m. [[0;1;31m*[0m[0;31m* [0m] A start job is running for Create V…s and Directories (10s / no limit) M[K[[0;32m OK [0m] Finished [0;1;39mCreate Volatile Files and Directories[0m. [K[[0;32m OK [0m] Reached target [0;1;39mSound Card[0m. Starting [0;1;39mNetwork Name Resolution[0m... Starting [0;1;39mNetwork Time Synchronization[0m... Starting [0;1;39mUpdate UTMP about System Boot/Shutdown[0m... [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Boot/Shutdown[0m. [[0;32m OK [0m] Started [0;1;39mNetwork Time Synchronization[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Initialization[0m. [[0;32m OK [0m] Started [0;1;39mDaily Cleanup of Temporary Directories[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Set[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Synchronized[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt download activities[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt upgrade and clean activities[0m. [[0;32m OK [0m] Started [0;1;39mPeriodic ext4 Onli…ata Check for All Filesystems[0m. [[0;32m OK [0m] Started [0;1;39mDiscard unused blocks once a week[0m. [[0;32m OK [0m] Reached target [0;1;39mTimers[0m. [[0;32m OK [0m] Listening on [0;1;39mD-Bus System Message Bus Socket[0m. [[0;32m OK [0m] Reached target [0;1;39mSockets[0m. [[0;32m OK [0m] Reached target [0;1;39mBasic System[0m. [[0;32m OK [0m] Started [0;1;39mD-Bus System Message Bus[0m. Starting [0;1;39mRemove Stale Onli…t4 Metadata Check Snapshots[0m... Starting [0;1;39mUser Login Management[0m... [[0;32m OK [0m] Started [0;1;39mNetwork Name Resolution[0m. [[0;32m OK [0m] Reached target [0;1;39mNetwork[0m. [[0;32m OK [0m] Reached target [0;1;39mHost and Network Name Lookups[0m. Starting [0;1;39mPermit User Sessions[0m... [[0;32m OK [0m] Finished [0;1;39mPermit User Sessions[0m. [[0;32m OK [0m] Started [0;1;39mGetty on tty1[0m. [[0;32m OK [0m] Started [0;1;39mSerial Getty on ttyS0[0m. [[0;32m OK [0m] Reached target [0;1;39mLogin Prompts[0m. [[0;32m OK [0m] Started [0;1;39mUser Login Management[0m. [[0;32m OK [0m] Reached target [0;1;39mMulti-User System[0m. [[0;32m OK [0m] Finished [0;1;39mRemove Stale Onli…ext4 Metadata Check Snapshots[0m. [[0;32m OK [0m] Reached target [0;1;39mGraphical Interface[0m. Starting [0;1;39mUpdate UTMP about System Runlevel Changes[0m... [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Runlevel Changes[0m. Debian GNU/Linux 11 debian��V��armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.179-cip32-rt13 #1 SMP Thu May 18 21:43:08 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/936509/extract-nfsrootfs-lxjxb4wo' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/936509/extract-nfsrootfs-lxjxb4wo' / # export NFS_SERVER_IP='192.168.11.5' export NFS_SERVER_IP='192.168.11.5' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-936509/environment . /lava-936509/environment / # /lava-936509/bin/lava-test-runner /lava-936509/0 /lava-936509/bin/lava-test-runner /lava-936509/0 + export TESTRUN_ID=0_dmesg + cd /lava-936509/0/tests/0_dmesg + cat uuid + UUID=936509_1.6.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 38.894735] <8>[ 39.084567] <8>[ 39.249004] + set +x <8>[ 39.407664] <8>[ 39.410159] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-936509/environment / # . /lava-936509/environment/lava-936509/bin/lava-test-runner /lava-936509/1 / # /lava-936509/bin/lava-test-runner /lava-936509/1 + export TESTRUN_ID=1_bootrr + cd /lava-936509/1/tests/1_bootrr + cat uuid + UUID=936509_1.6.2.4.5 + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-936509/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/<8>[ 40.123013] bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto pm33xx /lava-936509/1/../bin/lava-test-case <8>[ 41.379141] /lava-936509/1/../bin/lava-test-case <8>[ 41.512816] /lava-936509/1/../bin/lava-test-case <8>[ 41.587020] /lava-936509/1/../bin/lava-test-case <8>[ 41.738071] /lava-936509/1/../bin/lava-test-case <8>[ 41.855477] /lava-936509/1/../bin/lava-test-case <8>[ 41.949067] /lava-936509/1/../bin/lava-test-case <8>[ 42.064091] /lava-936509/1/../bin/lava-test-case <8>[ 42.187493] /lava-936509/1/../bin/lava-test-case <8>[ 42.283301] /lava-936509/1/../bin/lava-test-case <8>[ 42.395961] /lava-936509/1/../bin/lava-test-case <8>[ 42.485385] /lava-936509/1/../bin/lava-test-case <8>[ 42.611979] /lava-936509/1/../bin/lava-test-case <8>[ 42.715500] /lava-936509/1/../bin/lava-test-case <8>[ 42.808314] /lava-936509/1/../bin/lava-test-case <8>[ 42.900385] /lava-936509/1/../bin/lava-test-case <8>[ 43.020152] /lava-936509/1/../bin/lava-test-case <8>[ 43.112673] /lava-936509/1/../bin/lava-test-case <8>[ 43.227590] /lava-936509/1/../bin/lava-test-case <8>[ 43.342502] /lava-936509/1/../bin/lava-test-case <8>[ 43.443442] /lava-936509/1/../bin/lava-test-case <8>[ 43.557244] /lava-936509/1/../bin/lava-test-case <8>[ 43.668696] /lava-936509/1/../bin/lava-test-case <8>[ 43.761931] /lava-936509/1/../bin/lava-test-case <8>[ 43.883325] /lava-936509/1/../bin/lava-test-case <8>[ 43.975480] /lava-936509/1/../bin/lava-test-case <8>[ 44.094633] /lava-936509/1/../bin/lava-test-case <8>[ 44.194422] /lava-936509/1/../bin/lava-test-case <8>[ 45.344085] /lava-936509/1/../bin/lava-test-case <8>[ 45.435804] /lava-936509/1/../bin/lava-test-case <8>[ 45.552892] /lava-936509/1/../bin/lava-test-case <8>[ 45.646013] /lava-936509/1/../bin/lava-test-case <8>[ 45.773622] /lava-936509/1/../bin/lava-test-case <8>[ 45.860408] /lava-936509/1/../bin/lava-test-case <8>[ 45.973370] /lava-936509/1/../bin/lava-test-case <8>[ 46.064192] /lava-936509/1/../bin/lava-test-case <8>[ 46.196218] /lava-936509/1/../bin/lava-test-case <8>[ 46.290044] /lava-936509/1/../bin/lava-test-case <8>[ 46.405851] /lava-936509/1/../bin/lava-test-case <8>[ 46.502007] /lava-936509/1/../bin/lava-test-case <8>[ 46.624428] /lava-936509/1/../bin/lava-test-case <8>[ 46.714799] /lava-936509/1/../bin/lava-test-case <8>[ 46.833530] /lava-936509/1/../bin/lava-test-case <8>[ 46.927677] /lava-936509/1/../bin/lava-test-case <8>[ 47.049564] /lava-936509/1/../bin/lava-test-case <8>[ 47.143496] /lava-936509/1/../bin/lava-test-case <8>[ 47.257090] /lava-936509/1/../bin/lava-test-case <8>[ 47.351794] /lava-936509/1/../bin/lava-test-case <8>[ 47.473943] /lava-936509/1/../bin/lava-test-case <8>[ 47.568894] /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: 84: assert_device-present: not found /lava-936509/1/../bin/lava-test-case <8>[ 47.667728] /lava-936509/1/../bin/lava-test-case <8>[ 47.784759] /lava-936509/1/../bin/lava-test-case <8>[ 47.905424] + set +x <8>[ 47.927702] / #