[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (9 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10859041/tftp-deploy-1q63lzvj/kernel/zImage tftp 0x10000000 10859041/tftp-deploy-1q63lzvj/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '10859041/tftp-deploy-1q63lzvj/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 10.6 MiB/s done Bytes transferred = 9703936 (941200 hex) => tftp 0x14000000 10859041/tftp-deploy-1q63lzvj/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10859041/tftp-deploy-1q63lzvj/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '10859041/tftp-deploy-1q63lzvj/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 11.3 MiB/s done Bytes transferred = 12154051 (b974c3 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10859041/tftp-deploy-1q63lzvj/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10859041/tftp-deploy-1q63lzvj/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '10859041/tftp-deploy-1q63lzvj/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.7 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10859041/extract-nfsrootfs-th8dytza,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10859041/extract-nfsrootfs-th8dytza,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x941200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12153987 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.184-cip36-rt14 (KernelCI@build-j76105-arm-gcc-10-multi-v7-defconfig-r7tw2) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Jun 22 10:14:33 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s33676 r8192 d23668 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10859041/extract-nfsrootfs-th8dytza,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 936464K/1048576K available (14336K kernel code, 2332K rwdata, 5360K rodata, 2048K init, 417K bss, 46576K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000017] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.003888] Console: colour dummy device 80x30 [ 0.003937] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.003951] pid_max: default: 32768 minimum: 301 [ 0.004114] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004136] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004768] CPU: Testing write buffer coherency: ok [ 0.004799] CPU0: Spectre v2: using BPIALL workaround [ 0.005056] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005780] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.007389] rcu: Hierarchical SRCU implementation. [ 0.011014] EFI services will not be available. [ 0.011324] smp: Bringing up secondary CPUs ... [ 0.012147] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.012161] CPU1: Spectre v2: using BPIALL workaround [ 0.013082] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.013095] CPU2: Spectre v2: using BPIALL workaround [ 0.013994] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.014007] CPU3: Spectre v2: using BPIALL workaround [ 0.014122] smp: Brought up 1 node, 4 CPUs [ 0.014133] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.014142] CPU: All CPU(s) started in SVC mode. [ 0.014697] devtmpfs: initialized [ 0.022236] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.022472] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.022494] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.025614] pinctrl core: initialized pinctrl subsystem [ 0.027473] DMI not present or invalid. [ 0.028319] NET: Registered protocol family 16 [ 0.031884] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.034234] thermal_sys: Registered thermal governor 'step_wise' [ 0.034417] cpuidle: using governor menu [ 0.034595] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.218416] vdd1p1: supplied by regulator-dummy [ 0.225998] vdd3p0: supplied by regulator-dummy [ 0.233532] vdd2p5: supplied by regulator-dummy [ 0.241078] vddarm: supplied by regulator-dummy [ 0.248757] vddpu: supplied by regulator-dummy [ 0.256129] vddsoc: supplied by regulator-dummy [ 0.600468] No ATAGs? [ 0.600617] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.600627] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.604812] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.611024] Serial: AMBA PL011 UART driver [ 0.613228] printk: console [ramoops-1] enabled [ 0.613443] pstore: Registered ramoops as persistent store backend [ 0.613450] ramoops: using 0x10000@0x30000000, ecc: 0 [ 0.646235] iommu: Default domain type: Translated [ 0.646669] vgaarb: loaded [ 0.647575] SCSI subsystem initialized [ 0.648149] usbcore: registered new interface driver usbfs [ 0.648201] usbcore: registered new interface driver hub [ 0.648241] usbcore: registered new device driver usb [ 0.649818] i2c i2c-0: IMX I2C adapter registered [ 0.651167] i2c i2c-1: IMX I2C adapter registered [ 0.651988] i2c i2c-2: IMX I2C adapter registered [ 0.653357] pps_core: LinuxPPS API ver. 1 registered [ 0.653364] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.653388] PTP clock support registered [ 0.657067] clocksource: Switched to clocksource mxc_timer1 [ 1.716418] NET: Registered protocol family 2 [ 1.716857] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.718107] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.718151] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.718233] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.718383] TCP: Hash tables configured (established 8192 bind 8192) [ 1.718584] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.718629] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.718813] NET: Registered protocol family 1 [ 1.719420] RPC: Registered named UNIX socket transport module. [ 1.719429] RPC: Registered udp transport module. [ 1.719433] RPC: Registered tcp transport module. [ 1.719437] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.719447] PCI: CLS 0 bytes, default 64 [ 1.719937] Trying to unpack rootfs image as initramfs... [ 2.684507] Freeing initrd memory: 11872K [ 2.684952] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 2.685363] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.687301] Initialise system trusted keyrings [ 2.687610] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.693478] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.694226] NFS: Registering the id_resolver key type [ 2.694305] Key type id_resolver registered [ 2.694311] Key type id_legacy registered [ 2.694410] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.694418] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.694453] ntfs: driver 2.1.32 [Flags: R/O]. [ 2.694920] Key type asymmetric registered [ 2.694928] Asymmetric key parser 'x509' registered [ 2.694979] bounce: pool size: 64 pages [ 2.695019] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 2.695027] io scheduler mq-deadline registered [ 2.695033] io scheduler kyber registered [ 2.735270] mxs-dma 110000.dma-apbh: initialized [ 2.740103] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 2.740120] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 2.802239] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.806750] SuperH (H)SCI(F) driver initialized [ 2.807784] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 2.808818] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 2.808857] printk: console [ttymxc1] enabled [ 2.810274] msm_serial: driver initialized [ 2.810545] STMicroelectronics ASC driver initialized [ 2.812510] STM32 USART driver initialized [ 2.823262] panel-simple panel-lcd: supply power not found, using dummy regulator [ 2.823425] panel-simple panel-lcd: Specify missing connector_type [ 2.823834] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 2.832588] brd: module loaded [ 2.842531] loop: module loaded [ 2.846532] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 2.846547] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 2.846557] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 2.846566] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 2.846653] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 2.846798] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 2.846882] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 2.849723] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 2.849752] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 2.849768] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 2.851276] scsi host0: ahci-imx [ 2.851648] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 2.864378] CAN device driver interface [ 2.865741] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.869306] pps pps0: new PPS source ptp0 [ 2.887956] fec 2188000.ethernet eth0: registered PHC device 0 [ 2.889477] e1000e: Intel(R) PRO/1000 Network Driver [ 2.889482] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.889544] igb: Intel(R) Gigabit Ethernet Network Driver [ 2.889549] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.895769] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.895815] usbcore: registered new interface driver pegasus [ 2.895856] usbcore: registered new interface driver asix [ 2.895894] usbcore: registered new interface driver ax88179_178a [ 2.895926] usbcore: registered new interface driver cdc_ether [ 2.895968] usbcore: registered new interface driver smsc75xx [ 2.896020] usbcore: registered new interface driver smsc95xx [ 2.896053] usbcore: registered new interface driver net1080 [ 2.896084] usbcore: registered new interface driver cdc_subset [ 2.896114] usbcore: registered new interface driver zaurus [ 2.896180] usbcore: registered new interface driver cdc_ncm [ 2.899882] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.899890] ehci-pci: EHCI PCI platform driver [ 2.899927] ehci-platform: EHCI generic platform driver [ 2.900225] ehci-orion: EHCI orion driver [ 2.900442] SPEAr-ehci: EHCI SPEAr driver [ 2.900634] ehci-st: EHCI STMicroelectronics driver [ 2.900822] ehci-exynos: EHCI Exynos driver [ 2.901003] ehci-atmel: EHCI Atmel driver [ 2.901183] tegra-ehci: Tegra EHCI driver [ 2.901407] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.901427] ohci-pci: OHCI PCI platform driver [ 2.901468] ohci-platform: OHCI generic platform driver [ 2.901731] SPEAr-ohci: OHCI SPEAr driver [ 2.901919] ohci-st: OHCI STMicroelectronics driver [ 2.902108] ohci-atmel: OHCI Atmel driver [ 2.903354] usbcore: registered new interface driver usb-storage [ 2.911665] i2c /dev entries driver [ 2.931728] sdhci: Secure Digital Host Controller Interface driver [ 2.931735] sdhci: Copyright(c) Pierre Ossman [ 2.934497] Synopsys Designware Multimedia Card Interface Driver [ 2.936491] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.937816] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 2.937864] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 2.939111] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 2.941738] ledtrig-cpu: registered to indicate activity on CPUs [ 2.942729] usbcore: registered new interface driver usbhid [ 2.942736] usbhid: USB HID core driver [ 2.949472] NET: Registered protocol family 10 [ 2.950478] Segment Routing with IPv6 [ 2.950563] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.951130] NET: Registered protocol family 17 [ 2.951145] can: controller area network core [ 2.951215] NET: Registered protocol family 29 [ 2.951223] can: raw protocol [ 2.951230] can: broadcast manager protocol [ 2.951241] can: netlink gateway - max_hops=1 [ 2.951644] Key type dns_resolver registered [ 2.953700] ThumbEE CPU extension supported. [ 2.953715] Registering SWP/SWPB emulation handler [ 2.954519] printk: console [ttymxc1]: printing thread started [ 2.954705] printk: console [ramoops-1]: printing thread started [ 2.954730] Loading compiled-in X.509 certificates [ 2.959799] pstore: Using crash dump compression: deflate [ 2.981173] panel-simple panel-lcd: supply power not found, using dummy regulator [ 2.981311] panel-simple panel-lcd: Specify missing connector_type [ 2.982842] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 2.988193] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 2.988514] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 2.991404] imx_usb 2184200.usb: No over current polarity defined [ 2.994944] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 2.994968] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 3.017071] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 3.017685] hub 1-0:1.0: USB hub found [ 3.017724] hub 1-0:1.0: 1 port detected [ 3.019774] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 3.024126] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.024250] panel-simple panel-lcd: Specify missing connector_type [ 3.025680] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.029969] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.030089] panel-simple panel-lcd: Specify missing connector_type [ 3.031467] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.033365] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.038918] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.039044] panel-simple panel-lcd: Specify missing connector_type [ 3.040474] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.174977] mmc2: new high speed SDHC card at address 0001 [ 3.175802] mmcblk2: mmc2:0001 SD 14.6 GiB [ 3.198593] ata1: SATA link down (SStatus 0 SControl 300) [ 3.198653] ahci-imx 2200000.sata: no device found, disabling link. [ 3.198660] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 3.215936] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 3.304804] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 3.304810] GPT:29296874 != 30560255 [ 3.304815] GPT:Alternate GPT header not at the end of the disk. [ 3.304818] GPT:29296874 != 30560255 [ 3.304821] GPT: Use GNU Parted to correct GPT errors. [ 3.304857] mmcblk2: p1 p2 p3 [ 3.310123] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.310250] panel-simple panel-lcd: Specify missing connector_type [ 3.311716] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.317049] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 3.557125] hub 1-1:1.0: USB hub found [ 3.564437] hub 1-1:1.0: 3 ports detected [ 3.611947] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.612071] panel-simple panel-lcd: Specify missing connector_type [ 3.613477] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 6.327594] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 6.357178] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.387181] Sending DHCP requests ., OK [ 6.427147] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 [ 6.427173] IP-Config: Complete: [ 6.427179] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 [ 6.427203] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) [ 6.427215] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 6.427228] nameserver0=192.168.201.1 [ 6.435612] Freeing unused kernel memory: 2048K [ 6.478688] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 [ 7.302753] imx-ipuv3 2400000.ipu: IPUv3H probed [ 7.312831] imx-ipuv3 2800000.ipu: IPUv3H probed [ 7.316884] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.317138] panel-simple panel-lcd: Specify missing connector_type [ 7.323802] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.340604] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.340786] panel-simple panel-lcd: Specify missing connector_type [ 7.342731] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.370305] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.370587] panel-simple panel-lcd: Specify missing connector_type [ 7.372453] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.372797] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.372920] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.373029] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.373128] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.402366] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.402549] panel-simple panel-lcd: Specify missing connector_type [ 7.404587] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.454711] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 7.469088] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 7.469517] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 7.469605] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 7.469901] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 7.469983] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 7.469997] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 7.470379] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 [ 7.488928] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.489001] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.489082] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.489134] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.495236] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.495414] panel-simple panel-lcd: Specify missing connector_type [ 7.498918] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.507615] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.507683] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.507742] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.507789] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.517714] caam 2100000.crypto: Entropy delay = 3200 [ 7.578515] caam 2100000.crypto: Instantiated RNG4 SH0 [ 7.620599] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 7.620772] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 7.620912] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 7.621043] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 7.639277] caam 2100000.crypto: Instantiated RNG4 SH1 [ 7.639305] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 7.639322] caam 2100000.crypto: job rings = 2, qi = 0 [ 7.657754] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 7.662134] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 7.662662] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.662823] panel-simple panel-lcd: Specify missing connector_type [ 7.664453] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.668036] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.668109] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.668167] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.668222] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.733692] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.733864] panel-simple panel-lcd: Specify missing connector_type [ 7.735717] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.798620] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.798695] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.798757] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.798814] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 8.021979] caam algorithms registered in /proc/crypto [ 8.027494] caam 2100000.crypto: registering rng-caam [ 8.040493] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.040796] panel-simple panel-lcd: Specify missing connector_type [ 8.045385] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.056148] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 8.056223] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 8.056294] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 8.056354] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 8.062181] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.062366] panel-simple panel-lcd: Specify missing connector_type [ 8.064709] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.070940] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 8.071004] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 8.071064] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 8.071107] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 8.209941] random: crng init done Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:09 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.35 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-5 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 9.530579] systemd[1]: System time before build time, advancing clock. [ 9.588479] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 9.589235] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 9.669739] systemd[1]: Set hostname to . [ OK ] Created slice system-getty.slice. [ 10.488255] systemd[1]: Queued start job for default target Graphical Interface. [ 10.490135] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 10.490158] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 10.490872] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-modprobe.slice. [ 10.557852] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 10.588508] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice User and Session Slice. [ 10.628160] systemd[1]: Created slice User and Session Slice. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 10.657939] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 10.687443] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ 10.717661] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 10.718204] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Paths. [ 10.747924] systemd[1]: Reached target Paths. [ OK ] Reached target Remote File Systems. [ 10.777472] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Slices. [ 10.807423] systemd[1]: Reached target Slices. [ OK ] Reached target Swap. [ 10.837549] systemd[1]: Reached target Swap. [ OK ] Listening on [ 10.868314] systemd[1]: Listening on initctl Compatibility Named Pipe. initctl Compatibility Named Pipe. [ OK ] Listening on [ 10.944253] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. Journal Socket (/dev/log[ 10.945689] systemd[1]: Listening on Journal Socket (/dev/log). ). [ OK ] Listening on Journal Socket. [ 10.988745] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Network Service Netlink Socket. [ 11.018576] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on udev Control Socket. [ 11.050088] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. [ 11.078523] systemd[1]: Listening on udev Kernel Socket. Mounting Kernel Debug File System... [ 11.107726] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 11.108210] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 11.111388] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Trace File System... [ 11.148264] systemd[1]: Mounting Kernel Trace File System... Starting Create list of st…odes for the curr[ 11.192027] systemd[1]: Starting Create list of static device nodes for the current kernel... ent kernel... Starting Load Kernel Module configfs... [ 11.241024] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module drm... [ 11.273691] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module fuse... [ 11.289157] systemd[1]: Starting Load Kernel Module fuse... Starting Journa[ 11.321175] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. l Service... [ 11.324950] systemd[1]: Starting Journal Service... Starting Load K[ 11.375780] systemd[1]: Starting Load Kernel Modules... ernel Modules... Starting Remount Root and Kernel File Systems... [ 11.410374] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Coldplug All udev Devices... [ 11.440707] systemd[1]: Starting Coldplug All udev Devices... [ OK ] Mounted Kernel Debug File System[0[ 11.471910] systemd[1]: Mounted Kernel Debug File System. m. [ OK ] Mounted Kernel Trace File System[0[ 11.517768] systemd[1]: Mounted Kernel Trace File System. m. [ OK ] Finished Create list of st… nodes for the current kernel. [ 11.568340] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Load Kernel Module configfs. [ 11.618799] systemd[1]: modprobe@configfs.service: Succeeded. [ 11.619509] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ 11.648493] systemd[1]: modprobe@drm.service: Succeeded. [ 11.649188] systemd[1]: Finished Load Kernel Module drm. [ OK ] Started Journal Service. [ 11.677684] systemd[1]: Started Journal Service. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... [ 11.928583] systemd-journald[295]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Network Name Resolution... [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Network Name Resolution. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.184-cip36-rt14 #1 SMP Thu Jun 22 10:14:33 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10859041/extract-nfsrootfs-th8dytza' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10859041/extract-nfsrootfs-th8dytza' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10859041/environment . /lava-10859041/environment / # /lava-10859041/bin/lava-test-runner /lava-10859041/0 /lava-10859041/bin/lava-test-runner /lava-10859041/0 + export TESTRUN_ID=0_dmesg + cd /lava-10859041/0/tests/0_dmesg + cat uuid + UUID=10859041_1.6.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 25.572584] [ 25.669159] [ 25.740951] + set +x [ 25.834014] [ 25.835002] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-10859041/environment / # . /lava-10859041/environment/lava-10859041/bin/lava-test-runner /lava-10859041/1 / # /lava-10859041/bin/lava-test-runner /lava-10859041/1 + export TESTRUN_ID=1_bootrr + cd /lava-10859041/1/tests/1_bootrr + cat uuid + UUID=10859041_1.6.2.4.5 + set +x + export PATH=/opt/[ 26.424217] bootrr/libexec/bootrr/helpers:/lava-10859041/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd panel-lvds0 120000.hdmi /lava-10859041/1/../bin/lava-test-case [ 27.575578] /lava-10859041/1/../bin/lava-test-case [ 27.654669] /lava-10859041/1/../bin/lava-test-case [ 27.688512] + set +x / # [ 27.717721]