[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (1366 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10859043/tftp-deploy-haaflgzh/kernel/zImage tftp 0x10000000 10859043/tftp-deploy-haaflgzh/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '10859043/tftp-deploy-haaflgzh/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 11.4 MiB/s done Bytes transferred = 9703936 (941200 hex) => tftp 0x14000000 10859043/tftp-deploy-haaflgzh/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10859043/tftp-deploy-haaflgzh/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '10859043/tftp-deploy-haaflgzh/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 10.8 MiB/s done Bytes transferred = 12150848 (b96840 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10859043/tftp-deploy-haaflgzh/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10859043/tftp-deploy-haaflgzh/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '10859043/tftp-deploy-haaflgzh/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.4 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10859043/extract-nfsrootfs-q6u6x3k6,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10859043/extract-nfsrootfs-q6u6x3k6,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x941200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12150784 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.184-cip36-rt14 (KernelCI@build-j76105-arm-gcc-10-multi-v7-defconfig-r7tw2) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Jun 22 10:14:33 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s33676 r8192 d23668 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10859043/extract-nfsrootfs-q6u6x3k6,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 936468K/1048576K available (14336K kernel code, 2332K rwdata, 5360K rodata, 2048K init, 417K bss, 46572K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000017] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.003891] Console: colour dummy device 80x30 [ 0.003942] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.003955] pid_max: default: 32768 minimum: 301 [ 0.004116] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004139] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004769] CPU: Testing write buffer coherency: ok [ 0.004800] CPU0: Spectre v2: using BPIALL workaround [ 0.005053] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005774] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.007388] rcu: Hierarchical SRCU implementation. [ 0.011015] EFI services will not be available. [ 0.011323] smp: Bringing up secondary CPUs ... [ 0.012151] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.012165] CPU1: Spectre v2: using BPIALL workaround [ 0.013087] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.013100] CPU2: Spectre v2: using BPIALL workaround [ 0.013994] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.014007] CPU3: Spectre v2: using BPIALL workaround [ 0.014123] smp: Brought up 1 node, 4 CPUs [ 0.014133] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.014142] CPU: All CPU(s) started in SVC mode. [ 0.014695] devtmpfs: initialized [ 0.022233] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.022469] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.022490] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.025618] pinctrl core: initialized pinctrl subsystem [ 0.027479] DMI not present or invalid. [ 0.028316] NET: Registered protocol family 16 [ 0.031928] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.034285] thermal_sys: Registered thermal governor 'step_wise' [ 0.034468] cpuidle: using governor menu [ 0.034641] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.218468] vdd1p1: supplied by regulator-dummy [ 0.226030] vdd3p0: supplied by regulator-dummy [ 0.233561] vdd2p5: supplied by regulator-dummy [ 0.241101] vddarm: supplied by regulator-dummy [ 0.248759] vddpu: supplied by regulator-dummy [ 0.256150] vddsoc: supplied by regulator-dummy [ 0.600484] No ATAGs? [ 0.600626] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.600637] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.604808] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.611006] Serial: AMBA PL011 UART driver [ 0.613219] printk: console [ramoops-1] enabled [ 0.613434] pstore: Registered ramoops as persistent store backend [ 0.613441] ramoops: using 0x10000@0x30000000, ecc: 0 [ 0.646240] iommu: Default domain type: Translated [ 0.646673] vgaarb: loaded [ 0.647579] SCSI subsystem initialized [ 0.648143] usbcore: registered new interface driver usbfs [ 0.648195] usbcore: registered new interface driver hub [ 0.648236] usbcore: registered new device driver usb [ 0.649831] i2c i2c-0: IMX I2C adapter registered [ 0.651180] i2c i2c-1: IMX I2C adapter registered [ 0.652009] i2c i2c-2: IMX I2C adapter registered [ 0.653377] pps_core: LinuxPPS API ver. 1 registered [ 0.653383] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.653407] PTP clock support registered [ 0.657157] clocksource: Switched to clocksource mxc_timer1 [ 1.717290] NET: Registered protocol family 2 [ 1.717720] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.718881] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.718925] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.719008] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.719156] TCP: Hash tables configured (established 8192 bind 8192) [ 1.719365] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.719410] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.719590] NET: Registered protocol family 1 [ 1.720201] RPC: Registered named UNIX socket transport module. [ 1.720210] RPC: Registered udp transport module. [ 1.720214] RPC: Registered tcp transport module. [ 1.720218] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.720228] PCI: CLS 0 bytes, default 64 [ 1.720709] Trying to unpack rootfs image as initramfs... [ 2.683868] Freeing initrd memory: 11868K [ 2.684342] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 2.684738] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.686606] Initialise system trusted keyrings [ 2.686949] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.692902] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.693647] NFS: Registering the id_resolver key type [ 2.693718] Key type id_resolver registered [ 2.693723] Key type id_legacy registered [ 2.693822] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.693830] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.693864] ntfs: driver 2.1.32 [Flags: R/O]. [ 2.694338] Key type asymmetric registered [ 2.694346] Asymmetric key parser 'x509' registered [ 2.694400] bounce: pool size: 64 pages [ 2.694439] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 2.694448] io scheduler mq-deadline registered [ 2.694454] io scheduler kyber registered [ 2.734762] mxs-dma 110000.dma-apbh: initialized [ 2.739620] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 2.739638] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 2.798236] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.802748] SuperH (H)SCI(F) driver initialized [ 2.803762] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 2.804792] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 2.804832] printk: console [ttymxc1] enabled [ 2.806315] msm_serial: driver initialized [ 2.806579] STMicroelectronics ASC driver initialized [ 2.808615] STM32 USART driver initialized [ 2.819165] panel-simple panel-lcd: supply power not found, using dummy regulator [ 2.819329] panel-simple panel-lcd: Specify missing connector_type [ 2.819736] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 2.828570] brd: module loaded [ 2.838527] loop: module loaded [ 2.842488] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 2.842504] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 2.842513] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 2.842523] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 2.842613] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 2.842779] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 2.842845] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 2.845682] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 2.845709] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 2.845724] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 2.847264] scsi host0: ahci-imx [ 2.847639] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 2.860288] CAN device driver interface [ 2.861678] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.865251] pps pps0: new PPS source ptp0 [ 2.884429] fec 2188000.ethernet eth0: registered PHC device 0 [ 2.885952] e1000e: Intel(R) PRO/1000 Network Driver [ 2.885958] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.886019] igb: Intel(R) Gigabit Ethernet Network Driver [ 2.886024] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.892331] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.892378] usbcore: registered new interface driver pegasus [ 2.892422] usbcore: registered new interface driver asix [ 2.892458] usbcore: registered new interface driver ax88179_178a [ 2.892494] usbcore: registered new interface driver cdc_ether [ 2.892540] usbcore: registered new interface driver smsc75xx [ 2.892590] usbcore: registered new interface driver smsc95xx [ 2.892627] usbcore: registered new interface driver net1080 [ 2.892659] usbcore: registered new interface driver cdc_subset [ 2.892690] usbcore: registered new interface driver zaurus [ 2.892761] usbcore: registered new interface driver cdc_ncm [ 2.896386] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.896393] ehci-pci: EHCI PCI platform driver [ 2.896428] ehci-platform: EHCI generic platform driver [ 2.896719] ehci-orion: EHCI orion driver [ 2.896943] SPEAr-ehci: EHCI SPEAr driver [ 2.897169] ehci-st: EHCI STMicroelectronics driver [ 2.897369] ehci-exynos: EHCI Exynos driver [ 2.897556] ehci-atmel: EHCI Atmel driver [ 2.897737] tegra-ehci: Tegra EHCI driver [ 2.897963] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.897983] ohci-pci: OHCI PCI platform driver [ 2.898026] ohci-platform: OHCI generic platform driver [ 2.898293] SPEAr-ohci: OHCI SPEAr driver [ 2.898487] ohci-st: OHCI STMicroelectronics driver [ 2.898678] ohci-atmel: OHCI Atmel driver [ 2.899937] usbcore: registered new interface driver usb-storage [ 2.908240] i2c /dev entries driver [ 2.928113] sdhci: Secure Digital Host Controller Interface driver [ 2.928120] sdhci: Copyright(c) Pierre Ossman [ 2.930875] Synopsys Designware Multimedia Card Interface Driver [ 2.932862] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.934161] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 2.934205] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 2.935478] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 2.938097] ledtrig-cpu: registered to indicate activity on CPUs [ 2.939085] usbcore: registered new interface driver usbhid [ 2.939092] usbhid: USB HID core driver [ 2.945750] NET: Registered protocol family 10 [ 2.946755] Segment Routing with IPv6 [ 2.946836] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.947454] NET: Registered protocol family 17 [ 2.947470] can: controller area network core [ 2.947541] NET: Registered protocol family 29 [ 2.947550] can: raw protocol [ 2.947557] can: broadcast manager protocol [ 2.947567] can: netlink gateway - max_hops=1 [ 2.947943] Key type dns_resolver registered [ 2.949995] ThumbEE CPU extension supported. [ 2.950010] Registering SWP/SWPB emulation handler [ 2.950812] printk: console [ttymxc1]: printing thread started [ 2.950993] printk: console [ramoops-1]: printing thread started [ 2.951019] Loading compiled-in X.509 certificates [ 2.956009] pstore: Using crash dump compression: deflate [ 2.977421] panel-simple panel-lcd: supply power not found, using dummy regulator [ 2.977567] panel-simple panel-lcd: Specify missing connector_type [ 2.979122] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 2.984380] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 2.984744] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 3.001647] imx_usb 2184200.usb: No over current polarity defined [ 3.010393] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 3.010422] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 3.025076] mmc2: new high speed SDHC card at address e624 [ 3.025866] mmcblk2: mmc2:e624 SL16G 14.8 GiB [ 3.037456] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 3.037464] GPT:29296874 != 31116287 [ 3.037470] GPT:Alternate GPT header not at the end of the disk. [ 3.037472] GPT:29296874 != 31116287 [ 3.037476] GPT: Use GNU Parted to correct GPT errors. [ 3.037513] mmcblk2: p1 p2 p3 [ 3.039865] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 3.044717] hub 1-0:1.0: USB hub found [ 3.044754] hub 1-0:1.0: 1 port detected [ 3.047010] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 3.051477] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.051605] panel-simple panel-lcd: Specify missing connector_type [ 3.053021] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.057256] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.057373] panel-simple panel-lcd: Specify missing connector_type [ 3.058760] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.060848] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.066058] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.066185] panel-simple panel-lcd: Specify missing connector_type [ 3.067644] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.189879] ata1: SATA link down (SStatus 0 SControl 300) [ 3.189925] ahci-imx 2200000.sata: no device found, disabling link. [ 3.189931] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 3.197455] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 3.337080] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 3.558052] hub 1-1:1.0: USB hub found [ 3.558180] hub 1-1:1.0: 3 ports detected [ 3.563213] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.563347] panel-simple panel-lcd: Specify missing connector_type [ 3.564744] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 6.327622] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 6.357202] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.387221] Sending DHCP requests ., OK [ 6.427172] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 [ 6.427196] IP-Config: Complete: [ 6.427202] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 [ 6.427225] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) [ 6.427237] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 6.427250] nameserver0=192.168.201.1 [ 6.435967] Freeing unused kernel memory: 2048K [ 6.471861] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 [ 7.314481] imx-ipuv3 2400000.ipu: IPUv3H probed [ 7.316840] imx-ipuv3 2800000.ipu: IPUv3H probed [ 7.327634] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.327843] panel-simple panel-lcd: Specify missing connector_type [ 7.329873] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.418611] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.418776] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.418890] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.418996] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.422125] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.422591] panel-simple panel-lcd: Specify missing connector_type [ 7.424578] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.486092] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 7.487474] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 7.487959] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 7.488051] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 7.488334] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 7.488405] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 7.488417] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 7.488782] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 [ 7.489529] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.489589] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.489658] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.489700] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.491187] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.491347] panel-simple panel-lcd: Specify missing connector_type [ 7.493030] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.504770] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.504841] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.504909] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.504955] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.535379] caam 2100000.crypto: Entropy delay = 3200 [ 7.593491] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.593653] panel-simple panel-lcd: Specify missing connector_type [ 7.595383] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.596176] caam 2100000.crypto: Instantiated RNG4 SH0 [ 7.603972] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.604037] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.604092] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.604139] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.610603] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 7.614769] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 7.644273] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.644454] panel-simple panel-lcd: Specify missing connector_type [ 7.646213] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.652547] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 7.652757] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 7.652916] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 7.653067] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 7.653293] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.653352] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.653411] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.653456] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.654944] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.655104] panel-simple panel-lcd: Specify missing connector_type [ 7.656848] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.656936] caam 2100000.crypto: Instantiated RNG4 SH1 [ 7.656953] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 7.656961] caam 2100000.crypto: job rings = 2, qi = 0 [ 7.669317] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.669381] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.669436] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.669483] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.671289] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.671477] panel-simple panel-lcd: Specify missing connector_type [ 7.673509] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.682179] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.682245] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.682302] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.682345] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 8.113851] caam algorithms registered in /proc/crypto [ 8.115236] caam 2100000.crypto: registering rng-caam [ 8.116926] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.117256] panel-simple panel-lcd: Specify missing connector_type [ 8.119182] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.128446] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 8.128515] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 8.128581] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 8.128623] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 8.130109] panel-simple panel-lcd: supply power not found, using dummy regulator Begin: Loading essential drivers [ 8.130293] panel-simple panel-lcd: Specify missing connector_type ... [ 8.132110] panel-simple panel-lvds0: supply power not found, using dummy regulator done. [ 8.138824] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) Begin: Running /scripts/init-prem[ 8.138887] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) ount ... done. [ 8.138943] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) Begin: Mounting root file system [ 8.138987] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. [ 8.297669] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f0:fd mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.37 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-7 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 9.350446] systemd[1]: System time before build time, advancing clock. [ 9.396830] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 9.397643] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 9.459876] systemd[1]: Set hostname to . [ OK ] Created slice[ 10.332378] systemd[1]: Queued start job for default target Graphical Interface. system-getty.slice.[ 10.333864] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 10.333888] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 10.334694] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-modprobe.slice. [ 10.387803] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 10.418499] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice User and Session Slice. [ 10.448158] systemd[1]: Created slice User and Session Slice. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 10.478042] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 10.517841] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ 10.557469] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 10.557705] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Paths. [ 10.587929] systemd[1]: Reached target Paths. [ OK ] Reached target Remote File Systems. [ 10.617246] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Slices. [ 10.647410] systemd[1]: Reached target Slices. [ OK ] Reached target Swap. [ 10.677614] systemd[1]: Reached target Swap. [ OK ] Listening on initctl Compatibility Named Pipe. [ 10.708315] systemd[1]: Listening on initctl Compatibility Named Pipe. [ 11.016468] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ OK ] Listening on [ 11.026344] systemd[1]: Listening on Journal Socket (/dev/log). Journal Socket (/dev/log). [ OK ] Listening on [ 11.067980] systemd[1]: Listening on Journal Socket. Journal Socket. [ OK ] Listening on Network Service Netlink Socket. [ 11.099896] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on udev Control Socket. [ 11.130871] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. [ 11.158631] systemd[1]: Listening on udev Kernel Socket. Mounting Kernel[ 11.188403] systemd[1]: Condition check resulted in Huge Pages File System being skipped. Debug File System... [ 11.189323] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 11.195183] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Trace File System... [ 11.251996] systemd[1]: Mounting Kernel Trace File System... Starting Create[ 11.285512] systemd[1]: Starting Create list of static device nodes for the current kernel... list of st…odes for the current kernel... Starting Load Kernel Module configfs... [ 11.330879] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module drm... [ 11.360938] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module fuse... [ 11.390957] systemd[1]: Starting Load Kernel Module fuse... [ 11.433839] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 11.440606] systemd[1]: Starting Journal Service... Starting Journal Service... [ 11.486522] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... Starting Remount Root and Kernel File Systems... [ 11.531015] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Coldplug All udev Devices... [ 11.553053] systemd[1]: Starting Coldplug All udev Devices... [ OK ] Mounted Kernel Debug File System[0[ 11.583042] systemd[1]: Mounted Kernel Debug File System. m. [ OK ] Mounted Kernel Trace File System. [ 11.627998] systemd[1]: Mounted Kernel Trace File System. [ OK ] Finished Create list of st… nodes for the current kernel. [ 11.668326] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Load Kernel Module configf[ 11.730943] systemd[1]: modprobe@configfs.service: Succeeded. [ 11.731639] systemd[1]: Finished Load Kernel Module configfs. s. [ OK ] Finished Load Kernel Module drm. [ 11.788477] systemd[1]: modprobe@drm.service: Succeeded. [ 11.789185] systemd[1]: Finished Load Kernel Module drm. [ OK ] Started Journal Service. [ 11.817790] systemd[1]: Started Journal Service. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... [ 12.070950] systemd-journald[300]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Create Volatile Files and Directories. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Started Network Service. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Network Name Resolution... [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Network Name Resolution. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.184-cip36-rt14 #1 SMP Thu Jun 22 10:14:33 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10859043/extract-nfsrootfs-q6u6x3k6' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10859043/extract-nfsrootfs-q6u6x3k6' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-10859043/environment . /lava-10859043/environment / # /lava-10859043/bin/lava-test-runner /lava-10859043/0 /lava-10859043/bin/lava-test-runner /lava-10859043/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-10859043/0/tests/0_timesync-off ++ cat uuid + UUID=10859043_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-10859043/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=10859043_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip/linux-5.10.y-cip-rt/v5.10.184-cip36-rt14/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b imx6q-sabrelite -g cip -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-06-22 10:32:12-- http://storage.kernelci.org/cip/linux-5.10.y-cip-rt/v5.10.184-cip36-rt14/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1409520 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 2%[ ] 28.94K 109KB/s kselftest.tar.xz 6%[> ] 84.09K 158KB/s kselftest.tar.xz 7%[> ] 110.03K 138KB/s kselftest.tar.xz 11%[=> ] 151.96K 143KB/s kselftest.tar.xz 13%[=> ] 185.90K 139KB/s kselftest.tar.xz 14%[=> ] 206.18K 129KB/s kselftest.tar.xz 16%[==> ] 228.81K 123KB/s kselftest.tar.xz 18%[==> ] 255.19K 113KB/s kselftest.tar.xz 19%[==> ] 274.06K 108KB/s kselftest.tar.xz 21%[===> ] 299.51K 107KB/s kselftest.tar.xz 23%[===> ] 322.14K 105KB/s eta 10s kselftest.tar.xz 25%[====> ] 347.59K 104KB/s eta 10s kselftest.tar.xz 27%[====> ] 374.46K 104KB/s eta 10s kselftest.tar.xz 29%[====> ] 404.15K 104KB/s eta 10s kselftest.tar.xz 30%[=====> ] 419.22K 102KB/s eta 9s kselftest.tar.xz 32%[=====> ] 445.16K 103KB/s eta 9s kselftest.tar.xz 33%[=====> ] 467.78K 102KB/s eta 9s kselftest.tar.xz 34%[=====> ] 477.20K 98.4KB/s eta 9s kselftest.tar.xz 36%[======> ] 498.89K 97.8KB/s eta 9s kselftest.tar.xz 37%[======> ] 513.96K 89.5KB/s eta 9s kselftest.tar.xz 38%[======> ] 528.59K 87.1KB/s eta 9s kselftest.tar.xz 39%[======> ] 544.14K 82.0KB/s eta 9s kselftest.tar.xz 40%[=======> ] 558.28K 79.1KB/s eta 9s kselftest.tar.xz 41%[=======> ] 573.84K 77.6KB/s eta 9s kselftest.tar.xz 43%[=======> ] 592.22K 79.2KB/s eta 9s kselftest.tar.xz 44%[=======> ] 616.26K 80.5KB/s eta 9s kselftest.tar.xz 46%[========> ] 646.89K 79.5KB/s eta 9s kselftest.tar.xz 48%[========> ] 671.41K 79.5KB/s eta 9s kselftest.tar.xz 49%[========> ] 686.48K 77.9KB/s eta 8s kselftest.tar.xz 51%[=========> ] 702.52K 76.0KB/s eta 8s kselftest.tar.xz 52%[=========> ] 718.07K 74.2KB/s eta 8s kselftest.tar.xz 53%[=========> ] 735.04K 72.2KB/s eta 8s kselftest.tar.xz 54%[=========> ] 754.84K 74.1KB/s eta 8s kselftest.tar.xz 56%[==========> ] 773.22K 73.0KB/s eta 7s kselftest.tar.xz 58%[==========> ] 800.09K 76.0KB/s eta 7s kselftest.tar.xz 60%[===========> ] 829.30K 75.5KB/s eta 7s kselftest.tar.xz 62%[===========> ] 856.65K 77.6KB/s eta 7s kselftest.tar.xz 64%[===========> ] 882.10K 80.0KB/s eta 6s kselftest.tar.xz 64%[===========> ] 890.59K 79.4KB/s eta 6s kselftest.tar.xz 66%[============> ] 914.63K 81.6KB/s eta 6s kselftest.tar.xz 68%[============> ] 938.18K 80.1KB/s eta 6s kselftest.tar.xz 69%[============> ] 958.46K 79.2KB/s eta 5s kselftest.tar.xz 71%[=============> ] 981.09K 78.9KB/s eta 5s kselftest.tar.xz 72%[=============> ] 1002K 77.6KB/s eta 5s kselftest.tar.xz 74%[=============> ] 1.00M 77.9KB/s eta 5s kselftest.tar.xz 75%[==============> ] 1.02M 76.5KB/s eta 4s kselftest.tar.xz 77%[==============> ] 1.04M 76.9KB/s eta 4s kselftest.tar.xz 78%[==============> ] 1.05M 75.4KB/s eta 4s kselftest.tar.xz 79%[==============> ] 1.07M 72.5KB/s eta 4s kselftest.tar.xz 80%[===============> ] 1.08M 70.8KB/s eta 3s kselftest.tar.xz 81%[===============> ] 1.10M 70.5KB/s eta 3s kselftest.tar.xz 83%[===============> ] 1.12M 66.9KB/s eta 3s kselftest.tar.xz 84%[===============> ] 1.14M 64.3KB/s eta 3s kselftest.tar.xz 86%[================> ] 1.16M 66.0KB/s eta 2s kselftest.tar.xz 87%[================> ] 1.18M 64.5KB/s eta 2s kselftest.tar.xz 88%[================> ] 1.19M 63.8KB/s eta 2s kselftest.tar.xz 89%[================> ] 1.21M 61.0KB/s eta 2s kselftest.tar.xz 90%[=================> ] 1.22M 60.6KB/s eta 2s kselftest.tar.xz 92%[=================> ] 1.24M 60.9KB/s eta 2s kselftest.tar.xz 93%[=================> ] 1.26M 59.1KB/s eta 2s kselftest.tar.xz 94%[=================> ] 1.27M 58.6KB/s eta 2s kselftest.tar.xz 95%[==================> ] 1.28M 58.7KB/s eta 1s kselftest.tar.xz 96%[==================> ] 1.29M 56.1KB/s eta 1s kselftest.tar.xz 97%[==================> ] 1.31M 56.2KB/s eta 1s kselftest.tar.xz 98%[==================> ] 1.32M 56.6KB/s eta 1s kselftest.tar.xz 99%[==================> ] 1.34M 56.9KB/s eta 0s kselftest.tar.xz 100%[===================>] 1.34M 57.7KB/s in 18s 2023-06-22 10:32:30 (76.1 KB/s) - 'kselftest.tar.xz' saved [1409520/1409520] skiplist: ======================================== ======================================== filesystems:devpts_pts ============== Tests to run =============== filesystems:devpts_pts ===========End Tests to run =============== [ 50.433704] kselftest: Running tests in filesystems TAP version 13 1..1 # selftests: filesystems: devpts_pts # Failed to perform TIOCGPTPEER ioctl ok 1 selftests: filesystems: devpts_pts filesystems_devpts_pts pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #