[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11574822/tftp-deploy-3nxdd4c4/kernel/zImage tftp 0x10000000 11574822/tftp-deploy-3nxdd4c4/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '11574822/tftp-deploy-3nxdd4c4/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 14.4 MiB/s done Bytes transferred = 9708032 (942200 hex) => tftp 0x14000000 11574822/tftp-deploy-3nxdd4c4/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11574822/tftp-deploy-3nxdd4c4/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '11574822/tftp-deploy-3nxdd4c4/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 14.4 MiB/s done Bytes transferred = 16080023 (f55c97 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11574822/tftp-deploy-3nxdd4c4/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11574822/tftp-deploy-3nxdd4c4/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '11574822/tftp-deploy-3nxdd4c4/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.1 MiB/s done Bytes transferred = 42645 (a695 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x942200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16079959 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d694 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.194-cip39-rt16 (KernelCI@build-j51445-arm-gcc-10-multi-v7-defconfig-cw2tz) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Sep 19 21:59:16 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 16 pages/cpu s33676 r8192 d23668 u65536 [ 0.000000] pcpu-alloc: s33676 r8192 d23668 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932632K/1048576K available (14336K kernel code, 2332K rwdata, 5364K rodata, 2048K init, 417K bss, 50408K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008439] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022137] Console: colour dummy device 80x30 <6>[ 0.024030] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034442] CPU: Testing write buffer coherency: ok <6>[ 0.039571] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044870] pid_max: default: 32768 minimum: 301 <6>[ 0.049889] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057331] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066210] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071957] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079657] rcu: Hierarchical SRCU implementation. <6>[ 0.086655] EFI services will not be available. <6>[ 0.088898] smp: Bringing up secondary CPUs ... <6>[ 0.094185] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.099294] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105523] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.110516] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116735] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.121739] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127165] smp: Brought up 1 node, 4 CPUs <6>[ 0.131396] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137855] CPU: All CPU(s) started in SVC mode. <6>[ 0.143271] devtmpfs: initialized <6>[ 0.153831] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159178] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169042] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179255] pinctrl core: initialized pinctrl subsystem <6>[ 0.183754] DMI not present or invalid. <6>[ 0.186843] NET: Registered protocol family 16 <6>[ 0.194163] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200835] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.201018] cpuidle: using governor menu <6>[ 0.209084] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.400282] vdd1p1: supplied by regulator-dummy <6>[ 0.409868] vdd3p0: supplied by regulator-dummy <6>[ 0.419398] vdd2p5: supplied by regulator-dummy <6>[ 0.428937] vddarm: supplied by regulator-dummy <6>[ 0.438665] vddpu: supplied by regulator-dummy <6>[ 0.447980] vddsoc: supplied by regulator-dummy <6>[ 0.798247] No ATAGs? <6>[ 0.798431] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.806209] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.816461] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.826805] Serial: AMBA PL011 UART driver <6>[ 0.830511] printk: console [ramoops-1] enabled <6>[ 0.833303] pstore: Registered ramoops as persistent store backend <6>[ 0.839552] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.877713] iommu: Default domain type: Translated <6>[ 0.880488] vgaarb: loaded <5>[ 0.883843] SCSI subsystem initialized <7>[ 0.887308] libata version 3.00 loaded. <6>[ 0.891297] usbcore: registered new interface driver usbfs <6>[ 0.896865] usbcore: registered new interface driver hub <6>[ 0.902401] usbcore: registered new device driver usb <6>[ 0.909243] i2c i2c-0: IMX I2C adapter registered <6>[ 0.913969] i2c i2c-1: IMX I2C adapter registered <6>[ 0.918457] i2c i2c-2: IMX I2C adapter registered <6>[ 0.923882] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.927795] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.937198] PTP clock support registered <6>[ 0.944931] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.091783] NET: Registered protocol family 2 <6>[ 2.093970] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.102399] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.109876] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.117926] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.125398] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.132035] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.138781] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.146216] NET: Registered protocol family 1 <6>[ 2.151308] RPC: Registered named UNIX socket transport module. <6>[ 2.156841] RPC: Registered udp transport module. <6>[ 2.161763] RPC: Registered tcp transport module. <6>[ 2.166743] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.173431] PCI: CLS 0 bytes, default 64 <6>[ 2.178093] Trying to unpack rootfs image as initramfs... <6>[ 3.535109] Freeing initrd memory: 15704K <4>[ 3.537098] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.544341] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.554247] Initialise system trusted keyrings <6>[ 3.557339] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.569696] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.573674] NFS: Registering the id_resolver key type <5>[ 3.578371] Key type id_resolver registered <5>[ 3.582684] Key type id_legacy registered <6>[ 3.587058] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.593908] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.601609] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.606672] Key type asymmetric registered <5>[ 3.610525] Asymmetric key parser 'x509' registered <6>[ 3.615719] bounce: pool size: 64 pages <6>[ 3.619779] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.627422] io scheduler mq-deadline registered <6>[ 3.632187] io scheduler kyber registered <6>[ 3.676319] mxs-dma 110000.dma-apbh: initialized <4>[ 3.694504] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.701480] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.741057] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.749270] SuperH (H)SCI(F) driver initialized <6>[ 3.752210] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.761113] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.769055] printk: console [ttymxc1] enabled <6>[ 3.773557] printk: bootconsole [ec_imx21] disabled <6>[ 3.769055] printk: console [ttymxc1] enabled <6>[ 3.773557] printk: bootconsole [ec_imx21] disabled <6>[ 3.780235] msm_serial: driver initialized <6>[ 3.780494] STMicroelectronics ASC driver initialized <6>[ 3.782469] STM32 USART driver initialized <4>[ 3.792977] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.793126] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.793476] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.802375] brd: module loaded <6>[ 3.809865] loop: module loaded <6>[ 3.813826] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.813842] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.813852] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.813862] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.813942] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.814090] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.814152] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.817023] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.817052] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.817069] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.818575] scsi host0: ahci-imx <6>[ 3.818946] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.831537] CAN device driver interface <6>[ 3.832905] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.836463] pps pps0: new PPS source ptp0 <6>[ 3.870096] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.871597] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.871603] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.871662] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.871668] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.877961] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.878008] usbcore: registered new interface driver pegasus <6>[ 3.878051] usbcore: registered new interface driver asix <6>[ 3.878088] usbcore: registered new interface driver ax88179_178a <6>[ 3.878121] usbcore: registered new interface driver cdc_ether <6>[ 3.878169] usbcore: registered new interface driver smsc75xx <6>[ 3.878222] usbcore: registered new interface driver smsc95xx <6>[ 3.878255] usbcore: registered new interface driver net1080 <6>[ 3.878287] usbcore: registered new interface driver cdc_subset <6>[ 3.878318] usbcore: registered new interface driver zaurus <6>[ 3.878386] usbcore: registered new interface driver cdc_ncm <6>[ 3.882026] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.882034] ehci-pci: EHCI PCI platform driver <6>[ 3.882071] ehci-platform: EHCI generic platform driver <6>[ 3.882357] ehci-orion: EHCI orion driver <6>[ 3.882573] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.882760] ehci-st: EHCI STMicroelectronics driver <6>[ 3.882949] ehci-exynos: EHCI Exynos driver <6>[ 3.883128] ehci-atmel: EHCI Atmel driver <6>[ 3.883305] tegra-ehci: Tegra EHCI driver <6>[ 3.883531] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.883550] ohci-pci: OHCI PCI platform driver <6>[ 3.883593] ohci-platform: OHCI generic platform driver <6>[ 3.883857] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.884045] ohci-st: OHCI STMicroelectronics driver <6>[ 3.884235] ohci-atmel: OHCI Atmel driver <6>[ 3.885569] usbcore: registered new interface driver usb-storage <6>[ 3.893950] i2c /dev entries driver <6>[ 3.913776] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.913783] sdhci: Copyright(c) Pierre Ossman <6>[ 3.916601] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.918560] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.919858] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.919900] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.921318] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.923811] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.924782] usbcore: registered new interface driver usbhid <6>[ 3.924789] usbhid: USB HID core driver <6>[ 3.931593] NET: Registered protocol family 10 <6>[ 3.932657] Segment Routing with IPv6 <6>[ 3.932741] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.933323] NET: Registered protocol family 17 <6>[ 3.933339] can: controller area network core <6>[ 3.933412] NET: Registered protocol family 29 <6>[ 3.933420] can: raw protocol <6>[ 3.933429] can: broadcast manager protocol <6>[ 3.933439] can: netlink gateway - max_hops=1 <5>[ 3.933896] Key type dns_resolver registered <6>[ 3.936031] ThumbEE CPU extension supported. <5>[ 3.936046] Registering SWP/SWPB emulation handler <6>[ 3.936915] printk: console [ttymxc1]: printing thread started <6>[ 3.937088] printk: console [ramoops-1]: printing thread started <5>[ 3.937113] Loading compiled-in X.509 certificates <6>[ 3.942137] pstore: Using crash dump compression: deflate <6>[ 3.953255] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.961647] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <4>[ 3.963241] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.963374] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.964832] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.973311] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.976823] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.976849] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.004916] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.005508] hub 1-0:1.0: USB hub found <6>[ 4.005542] hub 1-0:1.0: 1 port detected <6>[ 4.007557] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.011802] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.011931] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.013299] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.017592] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.017721] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.019113] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.021000] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.026516] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.026657] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.028093] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.136245] mmc2: new high speed SDHC card at address e624 <6>[ 4.137036] mmcblk2: mmc2:e624 SL16G 14.8 GiB <6>[ 4.161489] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.161548] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.161555] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.173771] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <4>[ 4.214235] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.214241] GPT:7812499 != 31116287 <4>[ 4.214246] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.214249] GPT:7812499 != 31116287 <4>[ 4.214252] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.214289] mmcblk2: p1 p2 p3 <4>[ 4.219549] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.219689] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.221116] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.304908] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.547884] hub 1-1:1.0: USB hub found <6>[ 4.555565] hub 1-1:1.0: 3 ports detected <4>[ 4.596793] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.596918] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.598270] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.285387] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.295038] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.324917] Sending DHCP requests ., OK <6>[ 7.365018] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 <6>[ 7.365044] IP-Config: Complete: <6>[ 7.365049] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.365074] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) <6>[ 7.365087] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.365100] nameserver0=192.168.201.1 <6>[ 7.373549] Freeing unused kernel memory: 2048K <6>[ 7.427358] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.543355] udevd[136]: starting version 3.2.9 <5>[ 7.544159] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.544364] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.544459] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.555940] udevd[136]: specified user 'tss' unknown <27>[ 7.556091] udevd[136]: specified group 'tss' unknown <30>[ 7.558656] udevd[137]: starting eudev-3.2.9 <6>[ 7.962255] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 7.964252] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 7.969578] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.969763] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.971358] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.979119] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.979324] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.981187] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.986855] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.987038] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.988800] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.107230] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 8.115193] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.115351] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.115502] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.115631] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.115824] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.117764] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.139860] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.140033] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.141698] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.158560] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.195601] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.196022] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.196343] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.196431] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.219358] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.280120] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.280138] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.280148] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.284259] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.284348] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.284363] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.284776] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.308669] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.308735] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.308791] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.308835] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.310425] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.310605] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.312306] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.365822] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.365886] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.365953] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.365998] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.574766] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.575111] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.575295] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.575420] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 8.577022] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.577183] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.578978] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.607175] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.607268] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.607329] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.607374] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.637106] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.637364] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.640267] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.647160] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.650839] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.650907] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.650985] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.651035] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.656235] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 8.698849] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.699052] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.701197] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.712466] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.712672] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.712804] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.712855] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.996708] caam algorithms registered in /proc/crypto <6>[ 8.998228] caam 2100000.crypto: registering rng-caam <4>[ 9.000132] panel-simple panel-lcd: supply power not found, using dummy regulator done <4>[ 9.000337] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.002182] panel-simple panel-lvds0: supply power not found, using dummy regulator Saving random seed: <6>[ 9.013366] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) OK <6>[ 9.013428] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.013482] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) Starting network: <6>[ 9.013539] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.015076] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.015291] panel-simple panel-lcd: Specify missing connector_type ip: RTNETLINK answers: File exist<4>[ 9.017027] panel-simple panel-lvds0: supply power not found, using dummy regulator s <5>[ 9.072356] random: dd: uninitialized urandom read (32 bytes read) FAIL Starting dropbear sshd: <5>[ 9.164311] random: dropbear: uninitialized urandom read (32 bytes read) OK <5>[ 9.180678] random: crng init done /bin/sh: <5>[ 9.180696] random: 1 urandom warning(s) missed due to ratelimiting can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11574822/environment . /lava-11574822/environment / # /lava-11574822/bin/lava-test-runner /lava-11574822/0 /lava-11574822/bin/lava-test-runner /lava-11574822/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-11574822/0/tests/0_dmesg + cat uuid + UUID=11574822_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.<8>[ 9.777534] sh <8>[ 9.826461] <8>[ 9.859913] + set +x <8>[ 9.893246] <8>[ 9.894489] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11574822/environment / # . /lava-11574822/environment/lava-11574822/bin/lava-test-runner /lava-11574822/1 / # /lava-11574822/bin/lava-test-runner /lava-11574822/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-11574822/1/tests/1_bootrr + cat uuid + UUID=11574822_1.5.2.4.5 + set +x + export 'PAT<8>[ 10.410075] H=/opt/bootrr/libexec/bootrr/helpers:/lava-11574822/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto 120000.hdmi panel-lcd panel-lvds0 backlight-lcd backlight-lvds /lava-11574822/1/../bin/lava-test-case <8>[ 11.470268] /lava-11574822/1/../bin/lava-test-case <8>[ 11.502637] /lava-11574822/1/../bin/lava-test-case <8>[ 11.524009] + set +x / # <8>[ 11.535719]