[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.11 (10 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 14202797/tftp-deploy-v0tluxbm/kernel/zImage tftp 0x10000000 14202797/tftp-deploy-v0tluxbm/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '14202797/tftp-deploy-v0tluxbm/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 5.1 MiB/s done Bytes transferred = 9724416 (946200 hex) => tftp 0x14000000 14202797/tftp-deploy-v0tluxbm/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 14202797/tftp-deploy-v0tluxbm/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '14202797/tftp-deploy-v0tluxbm/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 4.7 MiB/s done Bytes transferred = 16085948 (f573bc hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 14202797/tftp-deploy-v0tluxbm/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 14202797/tftp-deploy-v0tluxbm/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '14202797/tftp-deploy-v0tluxbm/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.3 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x946200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16085884 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.218-cip49-rt20 (KernelCI@build-j220138-arm-gcc-10-defconfig-4d6dn) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Jun 6 12:51:29 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 16 pages/cpu s33676 r8192 d23668 u65536 [ 0.000000] pcpu-alloc: s33676 r8192 d23668 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932624K/1048576K available (14336K kernel code, 2332K rwdata, 5368K rodata, 2048K init, 417K bss, 50416K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008439] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022161] Console: colour dummy device 80x30 <6>[ 0.024053] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034464] CPU: Testing write buffer coherency: ok <6>[ 0.039595] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044893] pid_max: default: 32768 minimum: 301 <6>[ 0.049915] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057355] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066235] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071995] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079646] rcu: Hierarchical SRCU implementation. <6>[ 0.086607] EFI services will not be available. <6>[ 0.088842] smp: Bringing up secondary CPUs ... <6>[ 0.094147] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.099247] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105484] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.110469] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116694] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.121692] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127124] smp: Brought up 1 node, 4 CPUs <6>[ 0.131348] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137809] CPU: All CPU(s) started in SVC mode. <6>[ 0.143219] devtmpfs: initialized <6>[ 0.153618] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158962] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168827] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179036] pinctrl core: initialized pinctrl subsystem <6>[ 0.183491] DMI not present or invalid. <6>[ 0.186623] NET: Registered protocol family 16 <6>[ 0.194000] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200632] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200822] cpuidle: using governor menu <6>[ 0.208910] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.385105] vdd1p1: supplied by regulator-dummy <6>[ 0.394141] vdd3p0: supplied by regulator-dummy <6>[ 0.403112] vdd2p5: supplied by regulator-dummy <6>[ 0.412109] vddarm: supplied by regulator-dummy <6>[ 0.421221] vddpu: supplied by regulator-dummy <6>[ 0.429992] vddsoc: supplied by regulator-dummy <6>[ 0.753866] No ATAGs? <6>[ 0.754049] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.761827] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.772040] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.782374] Serial: AMBA PL011 UART driver <6>[ 0.786093] printk: console [ramoops-1] enabled <6>[ 0.788867] pstore: Registered ramoops as persistent store backend <6>[ 0.795098] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.832769] iommu: Default domain type: Translated <6>[ 0.835502] vgaarb: loaded <5>[ 0.838924] SCSI subsystem initialized <7>[ 0.842376] libata version 3.00 loaded. <6>[ 0.846388] usbcore: registered new interface driver usbfs <6>[ 0.851890] usbcore: registered new interface driver hub <6>[ 0.857475] usbcore: registered new device driver usb <6>[ 0.864300] i2c i2c-0: IMX I2C adapter registered <6>[ 0.869052] i2c i2c-1: IMX I2C adapter registered <6>[ 0.873473] i2c i2c-2: IMX I2C adapter registered <6>[ 0.878975] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.882823] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.892253] PTP clock support registered <6>[ 0.899963] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.053521] NET: Registered protocol family 2 <6>[ 2.055711] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.064342] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.071619] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.079639] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.087126] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.093808] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.100507] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.107936] NET: Registered protocol family 1 <6>[ 2.113010] RPC: Registered named UNIX socket transport module. <6>[ 2.118544] RPC: Registered udp transport module. <6>[ 2.123537] RPC: Registered tcp transport module. <6>[ 2.128462] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.135186] PCI: CLS 0 bytes, default 64 <6>[ 2.139817] Trying to unpack rootfs image as initramfs... <6>[ 3.501683] Freeing initrd memory: 15712K <4>[ 3.503604] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.510888] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.520801] Initialise system trusted keyrings <6>[ 3.523874] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.535950] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.539944] NFS: Registering the id_resolver key type <5>[ 3.544545] Key type id_resolver registered <5>[ 3.548937] Key type id_legacy registered <6>[ 3.553368] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.560180] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.567847] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.572950] Key type asymmetric registered <5>[ 3.576780] Asymmetric key parser 'x509' registered <6>[ 3.581980] bounce: pool size: 64 pages <6>[ 3.586032] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.593675] io scheduler mq-deadline registered <6>[ 3.598443] io scheduler kyber registered <6>[ 3.642697] mxs-dma 110000.dma-controller: initialized <4>[ 3.650041] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.657823] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 3.712439] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.720673] SuperH (H)SCI(F) driver initialized <6>[ 3.723632] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.732528] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.740466] printk: console [ttymxc1] enabled <6>[ 3.744962] printk: bootconsole [ec_imx21] disabled <6>[ 3.740466] printk: console [ttymxc1] enabled <6>[ 3.744962] printk: bootconsole [ec_imx21] disabled <6>[ 3.751528] msm_serial: driver initialized <6>[ 3.751790] STMicroelectronics ASC driver initialized <6>[ 3.753747] STM32 USART driver initialized <4>[ 3.764670] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.764827] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.765143] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.773842] brd: module loaded <6>[ 3.781247] loop: module loaded <6>[ 3.785181] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.785197] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.785207] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.785216] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.785293] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.785459] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.785518] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.788380] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.788408] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.788425] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.789946] scsi host0: ahci-imx <6>[ 3.790323] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.802808] CAN device driver interface <6>[ 3.804148] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.807699] pps pps0: new PPS source ptp0 <6>[ 3.841002] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.842529] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.842534] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.842597] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.842602] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.848778] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.848824] usbcore: registered new interface driver pegasus <6>[ 3.848868] usbcore: registered new interface driver asix <6>[ 3.848903] usbcore: registered new interface driver ax88179_178a <6>[ 3.848958] usbcore: registered new interface driver cdc_ether <6>[ 3.849005] usbcore: registered new interface driver smsc75xx <6>[ 3.849058] usbcore: registered new interface driver smsc95xx <6>[ 3.849091] usbcore: registered new interface driver net1080 <6>[ 3.849122] usbcore: registered new interface driver cdc_subset <6>[ 3.849154] usbcore: registered new interface driver zaurus <6>[ 3.849224] usbcore: registered new interface driver cdc_ncm <6>[ 3.852930] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.852938] ehci-pci: EHCI PCI platform driver <6>[ 3.852974] ehci-platform: EHCI generic platform driver <6>[ 3.853266] ehci-orion: EHCI orion driver <6>[ 3.853485] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.853676] ehci-st: EHCI STMicroelectronics driver <6>[ 3.853861] ehci-exynos: EHCI Exynos driver <6>[ 3.854044] ehci-atmel: EHCI Atmel driver <6>[ 3.854223] tegra-ehci: Tegra EHCI driver <6>[ 3.854445] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.854464] ohci-pci: OHCI PCI platform driver <6>[ 3.854509] ohci-platform: OHCI generic platform driver <6>[ 3.854784] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.854979] ohci-st: OHCI STMicroelectronics driver <6>[ 3.855166] ohci-atmel: OHCI Atmel driver <6>[ 3.856432] usbcore: registered new interface driver usb-storage <6>[ 3.864868] i2c /dev entries driver <6>[ 3.885081] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.885087] sdhci: Copyright(c) Pierre Ossman <6>[ 3.887894] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.889950] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.891240] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.891287] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.892570] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.895185] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.896178] usbcore: registered new interface driver usbhid <6>[ 3.896185] usbhid: USB HID core driver <6>[ 3.902930] NET: Registered protocol family 10 <6>[ 3.903979] Segment Routing with IPv6 <6>[ 3.904057] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.904624] NET: Registered protocol family 17 <6>[ 3.904641] can: controller area network core <6>[ 3.904718] NET: Registered protocol family 29 <6>[ 3.904726] can: raw protocol <6>[ 3.904734] can: broadcast manager protocol <6>[ 3.904744] can: netlink gateway - max_hops=1 <5>[ 3.905157] Key type dns_resolver registered <6>[ 3.907179] ThumbEE CPU extension supported. <5>[ 3.907194] Registering SWP/SWPB emulation handler <6>[ 3.908064] printk: console [ttymxc1]: printing thread started <6>[ 3.908247] printk: console [ramoops-1]: printing thread started <5>[ 3.908273] Loading compiled-in X.509 certificates <6>[ 3.913401] pstore: Using crash dump compression: deflate <6>[ 3.932931] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.933281] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <4>[ 3.934506] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.934640] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.936175] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.944656] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.948159] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.948183] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.969940] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.970570] hub 1-0:1.0: USB hub found <6>[ 3.970605] hub 1-0:1.0: 1 port detected <6>[ 3.979917] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 3.985084] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.985230] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.986961] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.992275] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.992438] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.995732] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.996574] mmc2: new high speed SDHC card at address 0001 <6>[ 3.998218] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 4.004605] mmcblk2: mmc2:0001 SD 14.6 GiB <4>[ 4.009044] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.009194] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.010690] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.021391] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.021398] GPT:7812499 != 30560255 <4>[ 4.021404] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.021407] GPT:7812499 != 30560255 <4>[ 4.021411] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.021448] mmcblk2: p1 p2 p3 <4>[ 4.026508] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.026633] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.028069] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.123023] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.123066] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.123073] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.135276] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.269930] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.490850] hub 1-1:1.0: USB hub found <6>[ 4.490977] hub 1-1:1.0: 3 ports detected <4>[ 4.495959] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.496082] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.497466] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 6.240474] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 6.270054] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.300070] Sending DHCP requests ., OK <6>[ 6.340018] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.11 <6>[ 6.340043] IP-Config: Complete: <6>[ 6.340049] device=eth0, hwaddr=00:19:b8:07:40:03, ipaddr=192.168.201.11, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.340073] host=imx6q-sabrelite-lava-cbg-0, domain=lava-rack, nis-domain=(none) <6>[ 6.340085] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.340102] nameserver0=192.168.201.1 <6>[ 6.340355] clk: Disabling unused clocks <6>[ 6.348246] Freeing unused kernel memory: 2048K <6>[ 6.406225] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.521374] udevd[143]: starting version 3.2.9 <5>[ 6.522159] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.522421] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.522516] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.529508] udevd[143]: specified user 'tss' unknown <27>[ 6.529630] udevd[143]: specified group 'tss' unknown <30>[ 6.531871] udevd[144]: starting eudev-3.2.9 <6>[ 6.870671] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 6.872725] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 6.877600] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 6.877778] panel-simple panel-lcd: Specify missing connector_type <4>[ 6.879769] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 6.915833] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 6.916001] panel-simple panel-lcd: Specify missing connector_type <4>[ 6.917507] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 6.972888] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 6.973040] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 6.973161] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 6.973261] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 6.985016] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 6.985178] panel-simple panel-lcd: Specify missing connector_type <4>[ 6.986809] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.079101] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.087887] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.088313] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.088403] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.090297] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.090368] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.090380] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.090801] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0 <6>[ 7.098721] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.098786] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.098846] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.098891] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.102344] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.102503] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.104159] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.112026] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.112093] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.112151] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.112196] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 7.225395] caam 2100000.crypto: Entropy delay = 3200 <6>[ 7.286193] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 7.346956] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 7.346976] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 7.346984] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 7.355051] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.355216] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.357000] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.369644] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.369712] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.369778] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.369823] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.531844] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 7.532129] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 7.536344] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.536501] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.540284] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.549961] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.550041] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.550110] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.550156] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.613771] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.613960] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.616917] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.621410] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.626445] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.626519] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.626612] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.626677] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 7.636041] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 7.688078] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.688276] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.690493] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.705260] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.705336] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.705417] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.705467] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 7.896363] caam algorithms registered in /proc/crypto <6>[ 7.897755] caam 2100000.crypto: registering rng-caam <4>[ 7.901546] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.901713] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.903434] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.908808] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.908868] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) done <6>[ 7.908925] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.908971] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.912285] panel-simple panel-lcd: supply power not found, using dummy regulator Saving random seed: <4>[ 7.912457] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.914250] panel-simple panel-lvds0: supply power not found, using dummy regulator OK <5>[ 7.987372] random: dd: uninitialized urandom read (32 bytes read) Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 8.074863] random: dropbear: uninitialized urandom read (32 bytes read) OK <5>[ 8.087036] random: crng init done <5>[ 8.087047] random: 1 urandom warning(s) missed due to ratelimiting /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-14202797/environment . /lava-14202797/environment / # /lava-14202797/bin/lava-test-runner /lava-14202797/0 /lava-14202797/bin/lava-test-runner /lava-14202797/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-14202797/0/tests/0_dmesg + cat uuid + UUID=14202797_1.5.2.4.1 + set +x + KERNELCI_LAVA<8>[ 8.695721] =y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.735002] <8>[ 8.773527] + set +x / # <8>[ 8.814772] <8>[ 8.816059]