Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2018.11-rc2-00101-g1ed3c0954b (Oct 25 2018 - 13:13:23 +0200) OMAP4430-GP ES2.1 Trying to boot from MMC1 SPL: Please implement spl_start_uboot() for your board SPL: Direct Linux boot not active! U-Boot 2018.11-rc2-00101-g1ed3c0954b (Oct 25 2018 - 13:13:23 +0200) CPU : OMAP4430-GP ES2.1 Board: OMAP4 Panda I2C: ready DRAM: 1 GiB MMC: OMAP SD/MMC: 0 Loading Environment from FAT... Unable to use mmc 0:1... Net: No ethernet found. Hit any key to stop autoboot: 2  0 => usb start usb start starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 1 Ethernet Device(s) found => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp Waiting for Ethernet connection... done. BOOTP broadcast 1 DHCP client bound to address 10.201.3.110 (22 ms) => setenv serverip 10.201.1.8 setenv serverip 10.201.1.8 => tftp 0x82000000 2171285/tftp-deploy-q9bqeo3r/kernel/zImage tftp 0x82000000 2171285/tftp-deploy-q9bqeo3r/kernel/zImage Waiting for Ethernet connection... done. Using sms0 device TFTP from server 10.201.1.8; our IP address is 10.201.3.110 Filename '2171285/tftp-deploy-q9bqeo3r/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 1.3 MiB/s done Bytes transferred = 9667072 (938200 hex) => tftp 0x84000000 2171285/tftp-deploy-q9bqeo3r/ramdisk/ramdisk.cpio.gz.uboot tftp 0x84000000 2171285/tftp-deploy-q9bqeo3r/ramdisk/ramdisk.cpio.gz.uboot Waiting for Ethernet connection... done. Using sms0 device TFTP from server 10.201.1.8; our IP address is 10.201.3.110 Filename '2171285/tftp-deploy-q9bqeo3r/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x84000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 1.3 MiB/s done Bytes transferred = 16047146 (f4dc2a hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x83f00000 2171285/tftp-deploy-q9bqeo3r/dtb/omap4-panda.dtb tftp 0x83f00000 2171285/tftp-deploy-q9bqeo3r/dtb/omap4-panda.dtb Waiting for Ethernet connection... done. Using sms0 device TFTP from server 10.201.1.8; our IP address is 10.201.3.110 Filename '2171285/tftp-deploy-q9bqeo3r/dtb/omap4-panda.dtb'. Load address: 0x83f00000 Loading: *###### 1.1 MiB/s done Bytes transferred = 86562 (15222 hex) => setenv bootargs 'console=ttyO2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyO2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x82000000 0x84000000 0x83f00000 bootz 0x82000000 0x84000000 0x83f00000 ## Loading init Ramdisk from Legacy Image at 84000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16047082 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83f00000 Booting using the fdt blob at 0x83f00000 Using Device Tree in place at 83f00000, end 83f18221 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.126-cip11 (KernelCI@build-j303258-arm-gcc-10-multi-v7-defconfig-mb7kk) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Mon Jul 4 06:38:48 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [411fc092] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI OMAP4 PandaBoard [ 0.000000] earlycon: omap8250 at MMIO 0x48020000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x98000000, size 8 MiB [ 0.000000] OF: reserved mem: initialized node dsp-memory@98000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x98800000, size 112 MiB [ 0.000000] OF: reserved mem: initialized node ipu-memory@98800000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 64 MiB at 0xbc000000 [ 0.000000] OMAP4: Map 0xafe00000 to (ptrval) for dram barrier [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afdfffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000afe00000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000afdfffff] [ 0.000000] node 0: [mem 0x00000000b0000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] OMAP4430 ES2.1 [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260100 [ 0.000000] Kernel command line: console=ttyO2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 808548K/1046528K available (13312K kernel code, 2230K rwdata, 5340K rodata, 2048K init, 425K bss, 49564K reserved, 188416K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <4>[ 0.000000] L2C: platform modifies aux control register: 0x0e070000 -> 0x3e470000 <4>[ 0.000000] L2C: DT/platform modifies aux control register: 0x0e070000 -> 0x3e470000 <6>[ 0.000000] L2C-310 errata 727915 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c4, AUX_CTRL 0x7e470000 <6>[ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz <6>[ 0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns <6>[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns <6>[ 0.011962] TI gptimer clockevent: always-on 32768 Hz at /ocp/interconnect@4a300000/segment@10000/target-module@8000 <6>[ 0.037322] Console: colour dummy device 80x30 <3>[ 0.042205] WARNING: Your 'console=ttyO2' has been replaced by 'ttyS2' <3>[ 0.049194] This ensures that you still see kernel messages. Please <3>[ 0.055908] update your kernel commandline. <6>[ 0.060516] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256) <6>[ 0.150482] pid_max: default: 32768 minimum: 301 <6>[ 0.155731] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.163513] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.172607] CPU: Testing write buffer coherency: ok <6>[ 0.177978] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.183715] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.190521] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.201934] rcu: Hierarchical SRCU implementation. <6>[ 0.217468] EFI services will not be available. <6>[ 0.222656] smp: Bringing up secondary CPUs ... <6>[ 0.263671] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.263671] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.275421] smp: Brought up 1 node, 2 CPUs <6>[ 0.279907] SMP: Total of 2 processors activated (2393.70 BogoMIPS). <6>[ 0.286743] CPU: All CPU(s) started in SVC mode. <6>[ 0.292388] devtmpfs: initialized <6>[ 0.315246] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1 <6>[ 0.323699] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.334106] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.359130] pinctrl core: initialized pinctrl subsystem <6>[ 0.368377] DMI not present or invalid. <6>[ 0.373504] NET: Registered protocol family 16 <6>[ 0.381378] DMA: preallocated 256 KiB pool for atomic coherent allocations <4>[ 0.393737] omap_hwmod: l3_main_3 using broken dt data from ocp <4>[ 0.401000] omap_hwmod: l3_main_2 using broken dt data from ocp <6>[ 0.424438] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.425109] cpuidle: using governor menu <6>[ 1.309387] omap-gpmc 50000000.gpmc: GPMC revision 6.0 <4>[ 1.314941] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 <6>[ 1.733032] No ATAGs? <6>[ 1.735778] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 1.744323] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 1.766571] Serial: AMBA PL011 UART driver <6>[ 1.815063] iommu: Default domain type: Translated <6>[ 1.820739] vgaarb: loaded <5>[ 1.824981] SCSI subsystem initialized <6>[ 1.829650] usbcore: registered new interface driver usbfs <6>[ 1.835662] usbcore: registered new interface driver hub <6>[ 1.841461] usbcore: registered new device driver usb <6>[ 1.849792] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.855194] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.864898] PTP clock support registered <6>[ 1.873840] clocksource: Switched to clocksource 32k_counter <6>[ 3.270111] NET: Registered protocol family 2 <6>[ 3.275238] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 3.284576] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 3.293487] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 3.301849] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 3.309631] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 3.316619] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 3.323791] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 3.331604] NET: Registered protocol family 1 <6>[ 3.337066] RPC: Registered named UNIX socket transport module. <6>[ 3.343444] RPC: Registered udp transport module. <6>[ 3.348632] RPC: Registered tcp transport module. <6>[ 3.353729] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 3.360656] PCI: CLS 0 bytes, default 64 <6>[ 3.365631] Trying to unpack rootfs image as initramfs... <6>[ 4.914947] Freeing initrd memory: 15672K <4>[ 4.919769] hw perfevents: no irqs for PMU, sampling events not supported <6>[ 4.927215] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 4.937957] Initialise system trusted keyrings <6>[ 4.943054] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 4.957427] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 4.964660] NFS: Registering the id_resolver key type <5>[ 4.970184] Key type id_resolver registered <5>[ 4.974792] Key type id_legacy registered <6>[ 4.979309] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 4.986511] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 4.994445] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 4.999755] Key type asymmetric registered <5>[ 5.004272] Asymmetric key parser 'x509' registered <6>[ 5.009643] bounce: pool size: 64 pages <6>[ 5.013916] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 5.021789] io scheduler mq-deadline registered <6>[ 5.026763] io scheduler kyber registered <6>[ 5.161590] OMAP GPIO hardware version 0.1 <4>[ 5.177764] ti-sysc: probe of 4a318000.target-module failed with error -16 <6>[ 5.469482] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) <6>[ 5.771942] pinctrl-single 4a31e040.pinmux: 28 pins, size 56 <6>[ 5.779083] pinctrl-single 4a100040.pinmux: 203 pins, size 406 <6>[ 5.938995] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 5.952331] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 114, base_baud = 3000000) is a 8250 <6>[ 5.961730] printk: console [ttyS2] enabled <6>[ 5.961730] printk: console [ttyS2] enabled <6>[ 5.970794] printk: bootconsole [omap8250] disabled <6>[ 5.970794] printk: bootconsole [omap8250] disabled <6>[ 5.982818] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 125, base_baud = 3000000) is a 8250 <6>[ 5.993347] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 126, base_baud = 3000000) is a 8250 <6>[ 6.004028] 4806e000.serial: ttyS3 at MMIO 0x4806e000 (irq = 127, base_baud = 3000000) is a 8250 <6>[ 6.017700] SuperH (H)SCI(F) driver initialized <6>[ 6.026031] msm_serial: driver initialized <6>[ 6.031097] STMicroelectronics ASC driver initialized <6>[ 6.040893] STM32 USART driver initialized <6>[ 6.048675] omap_rng 48090000.rng: Random Number Generator ver. 20 <5>[ 6.049224] random: crng init done <6>[ 6.089508] brd: module loaded <6>[ 6.101562] loop: module loaded <6>[ 6.141632] CAN device driver interface <6>[ 6.148986] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 6.158782] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 6.164062] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 6.170379] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 6.176086] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 6.196289] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 6.204101] usbcore: registered new interface driver pegasus <6>[ 6.210083] usbcore: registered new interface driver asix <6>[ 6.215850] usbcore: registered new interface driver ax88179_178a <6>[ 6.222259] usbcore: registered new interface driver cdc_ether <6>[ 6.228485] usbcore: registered new interface driver smsc75xx <6>[ 6.234588] usbcore: registered new interface driver smsc95xx <6>[ 6.240661] usbcore: registered new interface driver net1080 <6>[ 6.246673] usbcore: registered new interface driver cdc_subset <6>[ 6.252929] usbcore: registered new interface driver zaurus <6>[ 6.258880] usbcore: registered new interface driver cdc_ncm <6>[ 6.273071] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 6.279937] ehci-pci: EHCI PCI platform driver <6>[ 6.284729] ehci-platform: EHCI generic platform driver <6>[ 6.290893] ehci-orion: EHCI orion driver <6>[ 6.295715] SPEAr-ehci: EHCI SPEAr driver <6>[ 6.300415] ehci-st: EHCI STMicroelectronics driver <6>[ 6.305999] ehci-exynos: EHCI Exynos driver <6>[ 6.310852] ehci-atmel: EHCI Atmel driver <6>[ 6.315551] tegra-ehci: Tegra EHCI driver <6>[ 6.320312] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 6.326843] ohci-pci: OHCI PCI platform driver <6>[ 6.331604] ohci-platform: OHCI generic platform driver <6>[ 6.337860] ohci-platform 4a064800.ohci: Generic Platform OHCI controller <6>[ 6.345001] ohci-platform 4a064800.ohci: new USB bus registered, assigned bus number 1 <6>[ 6.353607] ohci-platform 4a064800.ohci: irq 106, io mem 0x4a064800 <6>[ 6.444763] hub 1-0:1.0: USB hub found <6>[ 6.448852] hub 1-0:1.0: 3 ports detected <6>[ 6.454101] SPEAr-ohci: OHCI SPEAr driver <6>[ 6.458953] ohci-st: OHCI STMicroelectronics driver <6>[ 6.464569] ohci-atmel: OHCI Atmel driver <6>[ 6.471405] usbcore: registered new interface driver usb-storage <6>[ 6.493835] i2c /dev entries driver <6>[ 6.539276] sdhci: Secure Digital Host Controller Interface driver <6>[ 6.545837] sdhci: Copyright(c) Pierre Ossman <6>[ 6.557556] Synopsys Designware Multimedia Card Interface Driver <6>[ 6.566589] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 6.579223] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 6.587646] usbcore: registered new interface driver usbhid <6>[ 6.593505] usbhid: USB HID core driver <6>[ 6.605255] NET: Registered protocol family 10 <6>[ 6.610748] Segment Routing with IPv6 <6>[ 6.614807] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 6.621459] NET: Registered protocol family 17 <6>[ 6.626220] can: controller area network core <6>[ 6.630920] NET: Registered protocol family 29 <6>[ 6.635681] can: raw protocol <6>[ 6.638916] can: broadcast manager protocol <6>[ 6.643371] can: netlink gateway - max_hops=1 <5>[ 6.648529] Key type dns_resolver registered <6>[ 6.653228] ThumbEE CPU extension supported. <5>[ 6.657806] Registering SWP/SWPB emulation handler <3>[ 6.663604] twl: not initialized <3>[ 6.667144] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660 <3>[ 6.675476] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660 <3>[ 6.683776] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660 <3>[ 6.692108] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660 <3>[ 6.700439] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660 <3>[ 6.708740] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660 <3>[ 6.717071] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1410000 Vs max 1316660 <6>[ 6.725372] Power Management for TI OMAP4+ devices. <4>[ 6.730529] OMAP4 PM: u-boot >= v2012.07 is required for full PM support <5>[ 6.738128] Loading compiled-in X.509 certificates <3>[ 6.849975] abe_cm:clk:0028:0: failed to enable <4>[ 6.854858] ti-sysc: probe of 4012208c.target-module failed with error -16 <3>[ 6.881408] abe_cm:clk:0068:0: failed to enable <4>[ 6.881408] ti-sysc: probe of 40130000.target-module failed with error -16 <6>[ 6.946624] omap_i2c 48060000.i2c: bus 2 rev0.10 at 100 kHz <4>[ 6.953887] Skipping twl internal clock init and using bootloader value (unknown osc rate) <6>[ 6.993591] twl 0-0048: PIH (irq 154) nested IRQs <4>[ 7.001861] twl_rtc 48070000.i2c:twl@48:rtc: Power up reset detected. <6>[ 7.009338] twl_rtc 48070000.i2c:twl@48:rtc: Enabling TWL-RTC <6>[ 7.017974] twl_rtc 48070000.i2c:twl@48:rtc: registered as rtc0 <6>[ 7.025482] twl_rtc 48070000.i2c:twl@48:rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <6>[ 7.056640] omap_i2c 48070000.i2c: bus 0 rev0.10 at 400 kHz <6>[ 7.064758] omap_i2c 48072000.i2c: bus 1 rev0.10 at 400 kHz <6>[ 7.071716] omap_i2c 48350000.i2c: bus 3 rev0.10 at 400 kHz <6>[ 7.092102] input: gpio_keys as /devices/platform/gpio_keys/input/input0 <4>[ 7.125183] hw-breakpoint: Failed to enable monitor mode on CPU 0. <4>[ 7.144622] hw-breakpoint: CPU 0 failed to disable vector catch <4>[ 7.415985] mmc0: host does not support reading read-only switch, assuming write-enable <6>[ 7.427368] mmc0: new high speed SDHC card at address 59b4 <6>[ 7.433868] mmcblk0: mmc0:59b4 USD 3.75 GiB <3>[ 7.798858] blk_update_request: I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 <3>[ 7.833404] blk_update_request: I/O error, dev mmcblk0, sector 1 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 <3>[ 7.868377] blk_update_request: I/O error, dev mmcblk0, sector 2 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 <3>[ 7.879577] blk_update_request: I/O error, dev mmcblk0, sector 3 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 <3>[ 7.914154] blk_update_request: I/O error, dev mmcblk0, sector 4 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 <3>[ 7.949096] blk_update_request: I/O error, dev mmcblk0, sector 5 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 <3>[ 7.984466] blk_update_request: I/O error, dev mmcblk0, sector 6 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 <3>[ 8.019134] blk_update_request: I/O error, dev mmcblk0, sector 7 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 <3>[ 8.029632] Buffer I/O error on dev mmcblk0, logical block 0, async page read <3>[ 8.086791] blk_update_request: I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 <3>[ 8.098449] blk_update_request: I/O error, dev mmcblk0, sector 1 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 <3>[ 8.255004] Buffer I/O error on dev mmcblk0, logical block 0, async page read <6>[ 8.262451] mmcblk0: unable to read partition table <3>[ 19.700317] l4_secure_cm:clk:0038:0: failed to disable <6>[ 19.713806] Freeing unused kernel memory: 2048K <6>[ 19.720336] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 19.823059] udevd[119]: starting version 3.2.9 <27>[ 19.834075] udevd[119]: specified user 'tss' unknown <27>[ 19.834075] udevd[119]: specified group 'tss' unknown <30>[ 19.848297] udevd[120]: starting eudev-3.2.9 <4>[ 21.204040] print_req_error: 6 callbacks suppressed <3>[ 21.204040] blk_update_request: I/O error, dev mmcblk0, sector 7862144 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 <3>[ 21.223907] blk_update_request: I/O error, dev mmcblk0, sector 7862145 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 <3>[ 21.235656] blk_update_request: I/O error, dev mmcblk0, sector 7862146 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 <3>[ 21.247344] blk_update_request: I/O error, dev mmcblk0, sector 7862147 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 <3>[ 21.282775] blk_update_request: I/O error, dev mmcblk0, sector 7862148 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 <3>[ 21.294525] blk_update_request: I/O error, dev mmcblk0, sector 7862149 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 <3>[ 21.306243] blk_update_request: I/O error, dev mmcblk0, sector 7862150 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 <3>[ 21.317962] blk_update_request: I/O error, dev mmcblk0, sector 7862151 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 <3>[ 21.378570] blk_update_request: I/O error, dev mmcblk0, sector 7862144 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 <3>[ 21.413665] blk_update_request: I/O error, dev mmcblk0, sector 7862145 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 <3>[ 21.498046] Buffer I/O error on dev mmcblk0, logical block 982768, async page read <6>[ 21.509826] twl6030_usb 48070000.i2c:twl@48:usb-comparator: Initialized TWL6030 USB module <6>[ 21.890228] ehci-omap: OMAP-EHCI Host Controller driver <6>[ 22.225494] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver <6>[ 22.231506] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 2 <6>[ 22.309661] hub 2-0:1.0: USB hub found <6>[ 22.313751] hub 2-0:1.0: 1 port detected <4>[ 22.641326] usb_phy_generic hsusb1_phy: dummy supplies not allowed for exclusive requests <6>[ 22.706939] ehci-omap 4a064c00.ehci: EHCI Host Controller <6>[ 22.712738] ehci-omap 4a064c00.ehci: new USB bus registered, assigned bus number 3 <6>[ 22.751464] ehci-omap 4a064c00.ehci: irq 107, io mem 0x4a064c00 <6>[ 22.783874] ehci-omap 4a064c00.ehci: USB 2.0 started, EHCI 1.00 <6>[ 22.792175] hub 3-0:1.0: USB hub found <6>[ 22.796386] hub 3-0:1.0: 3 ports detected <6>[ 23.094604] usb 3-1: new high-speed USB device number 2 using ehci-omap <6>[ 23.328216] hub 3-1:1.0: USB hub found <6>[ 23.333618] hub 3-1:1.0: 5 ports detected done Saving random seed: OK Starting network: OK Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # <6>[ 23.654571] usb 3-1.1: new high-speed USB device number 3 using ehci-omap # / # export SHELL=/bin/sh <6>[ 23.821502] smsc95xx v2.0.0 export SHELL=/bin/sh / # . /lava-2171285/environment . /lava-2171285/environment / # /lava-2171285/bin/lava-test-runner /lava-2171285/0 <6>[ 24.029632] SMSC LAN8700 usb-003:003:01: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=usb-003:003:01, irq=POLL) <6>[ 24.042602] smsc95xx 3-1.1:1.0 eth0: register 'smsc95xx' at usb-4a064c00.ehci-1.1, smsc95xx USB 2.0 Ethernet, 02:03:01:8c:13:b0 /lava-2171285/bin/lava-test-runner /lava-2171285/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-2171285/0/tests/0_dmesg<8>[ 24.150329] + cat uuid + UUID=2171285_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 24.187561] <8>[ 24.222381] <8>[ 24.253356] + <8>[ 24.263519] set +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-2171285/environment / # . /lava-2171285/environment/lava-2171285/bin/lava-test-runner /lava-2171285/1 / # /lava-2171285/bin/lava-test-runner /lava-2171285/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-2171285/1/tests/1_bootr<8>[ 24.776885] r + cat uuid + UUID=2171285_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-2171285/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-2171285/1/../bin/lava-test-case <8>[ 25.830078] /lava-2171285/1/../bin/lava-test-case <8>[ 25.865600] /lava-2171285/1/../bin/lava-test-case <8>[ 25.888244] + set +x <8>[ 25.907501] / #